TG-1 12F Specifica ation V1.1 TG-
peci Sp
-12F ific F_31 cati 133 ion Ve Copyr ersion right2 V1.1 2020 Copyright
2020 ShenzzhenAi-Thinker
TechnologyCo o.,LtdAllRights sReserved
1 18 TG-12F Specification V1.1 Disclaimer and copyright notice The information in this article, including the URL address for reference, is subject to change without prior notice.The Documentation is provided "as is" without any warranty, including any warranties of merchantability, fitness for a particular purpose, or non-infringement, and any warranties mentioned in the proposal, specification or sample. This document is not responsible for any infringement of any patent rights arising out of the use of the information in this document. No license, express or implied, by estoppel or otherwise, is hereby granted. The test data obtained in this paper are all obtained by Ai-Thinker laboratory , and the actual results may be slightly different.The Wi-Fi alliance membership mark is owned by the WiFi alliance. All trade mark names, trademarks and registered trademarks mentioned herein are the property of their respective owners and are hereby declared. The final interpretation right is owned by Shenzhen Ai-Thinker Technology Co., Ltd. Note The contents of this manual may be changed due to the version upgrade of the product or other reasons. Shenzhen Ai-Thinker Technology Co., Ltd. reserves the right to modify the contents of this manual without any notice. This manual is only used as a guide, and Shenzhen Ai-Thinker Technology Co., Ltd. makes every effort to provide accurate information in this manual, but Shenzhen Ai-Thinker Technology Co., Ltd. does not ensure that the contents of the manual are completely true,, All statements and information in this manual. and the recommendations do not constitute for any warranty, express or implied. Copyright2020 ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved
2 18
TG-12F Specification V1.1 Documentdevelopment/revision/revocationresume Version Date Revisedcontent Edition Approve V1.0 2020.10.15 First Edition V1.1 2020.10.26 Update Yuan Nannan Guan Ning Xu Hong Xu Hong Copyright2020 ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved
3 18
TG-12F Specification V1.1 CONTENT 1.Product Overview.......................................................................................................................................5 2.Electrical parameters.............................................................................................................................8 3.Appearance dimensions...........................................................................................................................10
((Pictureandlabelprintingareforreferenceonly,subjecttophysicalobject)).............................................10 4.Pin definition.........................................................................................................................................12
((Pictureandlabelprintingareforreferenceonly,subjecttophysicalobject)).............................................12 5.Schematic diagrams.................................................................................................................................14 6.Design guidance.......................................................................................................................................15 7.Reflow soldering.....................................................................................................................................17 8.Packaging information...........................................................................................................................18 9. Contact us...............................................................................................................................................18 Copyright2020 ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved
4 18
TG-12F Specification V1.1 1.Product Overview TG-12F_3133 is a module based on Tmall TG7100C WiFi+ BLE chip, which is designed with 2.4 G frequency band, WiFi 802.11b/g/n and BLE5.0 baseband/MAC designed, with high performance, low cost, quick and easy development characteristics. Suitable for low power consumption and high performance application development, and is also an integrated solution that can connect Tmall Genie directly. The micro controller subsystem consists of low power 32-bit RISC CPU cache and memory. It can control low power mode through power management unit. At the same time, it can support AES 256 bit encryption engine and has many security characteristics. For Software, pre-integrated Tmall Giene standard firmware, support customizable SDK, and to assist terminal products through the Tmall giene control certification. This chip Built-in 276 KB SRAM,128KB ROM.TG-12F support a variety of low-power working states, can meet the power consumption requirements of various application scenarios. TG-12F provide rich peripheral interfaces, including DSIOSPII2CIR remote PWMADCDACPIR and GPIO interfaces TG-12F_3133 has a variety of unique hardware security mechanisms. The hardware encryption accelerator supports AES 128/192/256 bit encryption engine and SHA-1/224/256, support Real random number generator (TRNG), public key accelerator (PKA) and so on, can be perfectly applied to various encryption products. Copyright2020 ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved
5 18 TG-12F Specification V1.1 Characteristics Complete 802.11b/g/n Wi-Fi + BLE SoC module, data rate up to 150Mbps TG-12F_3133 chip is 32-bit RISC CPU with FPU (floating point unit), operating frequency up to 192 MHz. The chip has built-in 276 KB SRAM and 128 KB ROM. Support SDIO/SPI/UART/I2C/IR remote/PWM/ADC/DAC/PIR/GPIO interface. SMD-22 package Integrated Wi-Fi MAC/ BB/RF/PA/LNA Support multiple sleep modes, deep sleep current is less than 30uA Support UART port local upgrade and remote firmware upgrade (FOTA) General AT commands can be quick and easy use Support secondary development, integrated Linux development environment Copyright2020 ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved
6 18 Main parameters TG-12F Specification V1.1 Table 1 main parameter descriptions Model Name TG-12F_3133 Package SMD-22 Size 24.0*16.0*3.0(0.2)MM Antenna On-board PCB antenna/IPEX Frequency Range Operating Temperature Store Temperature Power supply range Support Interface 2400 ~ 2483.5MHz
-40 ~ 85
-40 ~ 125 , < 90%RH Voltage: 3.0V ~ 3.6Velectrical current:>500mA SDIO/SPI/UART/I2C/IR remote/PWM/ADC/DAC/PIR/GPIO IO Support 110 ~ 4608000 bps default 115200 bps Security AES/SHA/PKA SPI Flash 2MB Copyright2020 ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved
7 18 TG-12F Specification V1.1 2.Electrical parameters Electrical characteristics Parameters Conditions Min Typ Max Unit Supply voltage VDD 3.0 3.3 3.6 V VIL/VIH I/O VOL/VOH IMAX
-0.3/0.75VIO N/0.8VIO
0.25VIO/3.6 V 0.1VIO/N 12 V mA RF parameters Description Operating frequency Typical values 2400 - 2483.5 Output power 11n mode HT20PA output power 11g modePA output power 11b modePA output power 152 162 182 CCK, 1 Mbps CCK, 11 Mbps Receiving sensitivity
-97
-88 Unit MHz dBm dBm dBm dBm dBm Copyright2020 ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved
8 18 6 Mbps (1/2 BPSK) 54 Mbps (3/4 64-QAM) HT20 (MCS7) Power consumption TG-12F Specification V1.1
-92
-75
-72 dBm dBm dBm The following power consumption data are based on a 3.3 V power supply ,25C ambient temperature and measured using an internal voltage regulator. All measurements were completed at the antenna interface without SAW filters All emission data are based on a duty cycle of 90%, measured in the mode of continuous emission. Mode Min Tx 802.11b, CCK 1Mbps, POUT=+21dBm Tx 802.11g, OFDM 54Mbps, POUT
=+18dBm Tx 802.11n, MCS7, POUT =+17dBm Rx 802.11b,1024 byte, -80dBm Rx 802.11g,1024 byte, -70dBm Rx 802.11n,1024 byte, -65dBm Deep-Sleep Power Off
Typ 180 145 Max 320 250 135 250 40 40 40 30 1
Unit mA mA mA mA mA mA A A Copyright2020 ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved
9 18 TG-1 12F Specifica ation V1.1 3.Appe earance dimensi ons TG-12F F_3133 Appeara ance Ima age
((Pictu ureandlabel printingaref forreference only,subject ttophysicalo object)) Copyright
2020 Shenz zhenAi-Thinker rTechnologyCo o.,LtdAllRights sReserved 10 18 TG-12F Specification V1.1 Copyright2020 ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved
11 18 4.Pin definition TG-12F Specification V1.1
((Pictureandlabelprintingareforreferenceonly,subjecttophysicalobject)) TG-12F module is connected to 22 interfaces, refer to pin diagram, pin function definition table is interface definition. TG-12F Pin diagram Table Pin function definition No. Name Function 1 2 3 IO0 SDIO,SFLASH,SPI,I2C,UART,PWM,GPIO IO11 SPI,I2C,UART,PWM,AUXADC,GPIO EN/RST Chip enable Copyright2020 ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved
12 18 TG-12F Specification V1.1 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 IO3 SDIO,SPI,I2C,UART,PWM,GPIO IO4 SDIO,SPI,I2C,UART,PWM,GPIO IO5 SDIO,SPI,I2C,UART,PWM,GPIO IO12 SPI,I2C,UART,PWM,AUXADC,GPIO VDD VDD NC XI XO Empty Pin Crystal oscillator Input 32.768KHz Crystal oscillator Input 32.768KHz IO14 SPI,I2C,UART,PWM,AUXADC,GPIO IO17 SFLASH,SPI,I2C,UART,PWM,GPIO IO20 SFLASH,SPI,I2C,UART,PWM,GPIO GND GND IO21 SFLASH,SPI,I2C,UART,PWM,GPIO IO22 SFLASH,SPI,I2C,UART,PWM,GPIO IO8 SPI,I2C,UART,PWM,AUXADC,GPIO IO1 SDIO,SFLASH,SPI,I2C,UART,PWM,GPIO IO2 SDIO,SFLASH,SPI,I2C,UART,PWM,GPIO RXD SPI,I2C,UART,PWM,AUXADC,GPIO TXD SPI,I2C,UART,PWM,GPIO Table Module Start-up Mode Description Pin EN/RST IO8 System start-up mode Default SPI Start-up mode Download Start-up Mode Pull up Drop-down 1 N/A 0 0 Copyright2020 ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved
13 18 TG-12F Specification V1.1 5.Schematic diagrams Copyright2020 ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved
14 18 TG-12F Specification V1.1 6.Design guidance 1Antenna layout requirements 1The installation position on the motherboard is recommended in the following two ways:
Scheme 1: put the module on the edge of the motherboard, and the antenna area extends out of the edge of the motherboard. Scheme two: put the module on the edge of the motherboard, the edge of the motherboard in the antenna position to make an empty area. 2In order to meet the performance of on-board antenna, metal parts are forbidden to be placed around the antenna, away from high frequency devices. 2Power supply 1Recommend 3.3V voltage, peak current above 50mA 2It is recommended to use LDO for power supply; if DC-DC is used, the ripple is recommended to be controlled within 30mV. 3DC-DC the power supply circuit, it is suggested to reserve the position of output ripple can be optimized when the load changes greatly. 4It is recommended to add ESD devices to the 3.3V power interface. Copyright2020 ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved
15 18 TG-12F Specification V1.1 3GPIO Interface 1The module periphery leads to some GPIO ports, such as the recommended resistance of 10-100 Ohms in series on the IO port. This can suppress overshoot, to ensure both sides of the level more stable. helpful for both EMI and ESD. 2 For special IO, please refer to the specification, which will affect the starting configuration of the module. 3The IO port of the module voltage is 3.3 V, if the main control does not match the IO level of the module, require to add the level conversion circuit. 4 When the IO port is connected directly to the peripheral interface, or the pin header and other terminals, it is recommended to reserve ESD device near the terminal. Electrical level conversion circuit Copyright2020 ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved
16 18 7.Reflow soldering TG-12F Specification V1.1 Copyright2020 ShenzhenAi-ThinkerTechnologyCo.,LtdAllRightsReserved
17 18 8.Pa ckaging g inform mation TG-1 12F Specifica ation V1.1 Refer t to below i image, the e TG-12Fpa ackage is in Tape/R Reel. 9. Con ntact us s Official l website:
https://ww w.ai-thinke er.com Developm ment DOCS http s
//d ocs.ai-
-thinker.co om Official l Forum: ht ttp://bbs.a i-thinker.c com Sample p purchase: h https://anx inke.taobao o.com Business s cooperati ion: sales@
aithinker.c com Technica al support:
support@a ithinker.co om Company Address: B Building C, Huafeng In ntelligent I Innovation P Port, Xixia ang, Baoan D District, Shenzhen n Tel :075 6 55-29162996 Copyright
2020 Shenz zhenAi-Thinker rTechnologyCo o.,LtdAllRights sReserved 18 18 Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules The TG-12F_3133 is an WIFI & BT Module with digitally modulated systems using an DSSS with DBPSK/DQPSK/CCK for 802.11b; OFDM with BPSK/QPSK/16QAM/64QAM for 802.11g/n; modulation and BLE GFSK modulation. It operates on the 2400-2483.5MHz band and, therefore, is within U.S. FCC part 15.247 standard 2.3 Specific operational use conditions The EUT is a WIFI & BT Module Operation Frequency: 2412-2462MHz for 802.11b/g/11n(HT20);
Modulation Type: DSSS with DBPSK/DQPSK/CCK for 802.11b;
OFDM with BPSK/QPSK/16QAM/64QAM for 802.11g/n;
Number Of Channel: 11 channels for 802.11b/g/11n(HT20);
Antenna Designation: PCB Antenna Antenna Gain: 0.5dBi BLE:
Operation Frequency: 2402-2480MHz for BLE;
Modulation Type: GFSK Number Of Channel: 40 channels Antenna Designation: PCB Antenna Antenna Gain: 0.5dBi TG-12F_3133 is a WIFI & BT module developed by Ensink Technology. The core processor TG7100C of this module is a highly integrated low-power Wi-Fi& BT system-on-chip (SoC) designed for the Internet of Things (IoT) , Mobile devices, wearable electronic devices, smart home and other applications. TG7100C has industry-leading low-power performance and RF performance, supports IEEE802.11b / g / n protocol, integrates Wi-Fi MAC, Wi-Fi RF and baseband, RF switch, RF Balun, power amplifier, low noise Amplifier, etc. 2.4 Limited module procedures not applicable; Single Modular Approval Request 2.5 Trace antenna designs Not applicable;
2.6 RF exposure considerations To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. 2.7 Antennas The TG-12F_3133 is an Wi-Fi Module beams signals and communicates with its antenna, which is PCB Antenna. The PCB Antenna gain is 0.5dBi. Antenna could not be in no-load state when module is working. During debugging, it is suggested to add 50 ohms load to the antenna port to avoid damage or performance degradation of the module under long-time no-load condition. 2.8 Label and compliance information The final end product must be label in a visible area with the following Host must Contains FCC ID: 2ATPO-TG12F. If the size of the end product is larger than 24x16mm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may cause undesired operation. 2.9 Information on test modes and additional testing requirements Data transfer module demo board can control the EUT work in RF test mode at specified test channel. 2.10 Additional testing, Part 15 Subpart B disclaimer The module without unintentional-radiator digital circuit, so the module does not required an evaluation by FCC Part 15 Subpart B. The host should be evaluated by the FCC Subpart B. ATTENTION This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) This device and its antenna(s) must not be colocated with any other transmitters except in accordance with FCC multitransmitter product procedures. Referring to the multitransmitter policy, multiple transmitter(s) and module(s) can be operated simultaneously without C2P. 3) For all products market in US, OEM has to limit the Operating Frequency: 2412-2462 MHz /2402-2480MHz by supplied firmware programming tool. OEM shall not supply any tool or info to the enduser regarding to Regulatory Domain change. USERS MANUAL OF THE END PRODUCT:
In the user manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radiofrequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.