FCC ID: 2AUMJEV-05 Personal Safety Watch

 

Smart Watch

Front

The smart watch is designed for the

elderly and lone worker. The watch

combines many intelligent functions,

such as SOS alarm, two way talking,

heart rate, pedometer and so on. The

operation is very simple. Please read

this operation guide carefully before

using it.

Touch Screen

Power Button

SOS Button

Watch Strap

1

Getting To Know Your Watch

2

Accessories

3

SIM Card Installation

4

Charging your Watch

5

Functions and Basic Settings

6

Making a phone call

Back

Side

USB Cable

Watch Strap

1

Remove Strap from watch.

Charging Pins

Charging Contacts

TIP

Please do as below picture shows.

Heart Rate Sensor

Charging Contacts

Microphone

SIM Card Holder

Speaker

Charging Base

User Manual

2

3

Remove SIM card holder from the watch and put a Nano

SIM on the holder.

Put the holder back and lock the strap on watch.

Smart

Watch

SIM

Charging

Connect the USB cable from

charging base to the AC adaptor.

Place the watch into the charging

base correctly, you will hear

spoken confirmation “your watch

is charging”.

Please fully charge the battery

daily for around 2 hours or when

battery is low.

The watch battery is not removable.

After a long period of inactivity, the

watch may not be turned on due to

low battery. please charge it every

day to ensure that the watch can

work normally.

When the watch is turned on, slide leftwards or rightwards to

view all available functions. it displays Watch Face, Weather,

Heart Rate, Contact, Steps and Settings.

Slide rightwards to enter the

interface of Contact, select

the contact person, and make

a call.

7

Steps

1

2

1

2

At watch face, you can see time, date, heart rate and steps.　

There are two watch faces for your option. Sliding right to

the end and click settings, select watch face and choose

what you like by sliding left and right.　

Keep sliding right to enter the

interface of Steps, step

counting is enabled by default

and opened all day. You can

also view distance and

consumed calories.

8

Heart Rate Measurement

9

Activating an SOS Alarm

Tips

10

Notes on Voicemail

11

Fall Alarm

12

Getting a GPS fix

13

General Specifications

There are two ways to activate SOS alarm.

1

Pressing the side button for 3 seconds until you feel the

watch vibrate.

We advise emergency contacts to switch off any

voice mail facility on their phone to prevent delay in

reaching help. However, the followin safe-guards

are used if a voicemail is reached:

The watch can automatically detect a fall. When this occurs

the watch will give a warning message to the user.

To get an initial GPS fix, go outdoors or near a window so

the watch can get a fix on the satellites. This could take few

minutes depending on your environment.

Stop fall alarm?

GPS

Wear the watch on the left hand and click heart

rate, after several seconds checking, the screen

the will display your heart rate BPM.

2

When screen is on, long press the screen for 3 seconds

until you feel the watch vibrate.

3sec.

3sec.

After SOS alarm is activated, you will hear a

voice prompt confirming the activation of the

SOS alert and allowing you approximately 10

seconds to cancel the alarm. If the SOS is not

cancelled in time an SOS alert text message is

immediately sent to the emergency contact

numbers followed by the outgoing calls.

If the watch fails to connect to the first number,

it will call the second number after delay of 10

seconds. In case the second number fails to be

connected as well, the system will connect to the

third number etc.

Between each call, it will have 10 seconds

delay, during this time, user can stop call

sequence or prevent a possible false alarm by

pressing SOS button.

The wearer can end the current call by clicking

the SOS button and the calling sequence to

continue if the voice mail does not automatically

disconnect.

An emergency contact can call back to the

watch if they are disconnected. Remember that

the watch maybe already calling the next contact

unless the calling sequence has been stopped.

some daily activities like sports oe even sitting down

abruptly can trigger the fall alarm.

The wearer has a short time to cancel a fall alarm by

clicking the Cancel on the watch. If the alarm is not

cancelled, emergency contacts will be called.

TIP

It is possible that the watch will not detect every

real fall. We strongly advise the wearer to press

the SOS button in any emergency situation, if they

are able.

TIP GPS functionality may be unavailable or inaccurate

in some locations (for example, availability or

accuracy of GPS location maybe impacted inside

buildings or near tall buildings or other tall features

or underground).

The watch also provides Wi-Fi, LBS positioning, when GPS

is unavailable, it will switch to Wi-Fi and LBS for locating.

The home Wi-Fi and beacons provide at home out of home

information in addition to optimizing watch battery life.

Please note Wi-Fi and LBS tracking service is not 100%

accurate, it can be used to approximate your location only.

1

2

3

4

5

6

Dimension: 47.5mm*16.9mm/1.87in*0.66in.

Weight: 65g/2.29oz.

Battery: Rechargeable, 3.7V,580mAh.

Charging voltage: 5V DC.

Waterproof: IPX8.

4 locating technologies: GPS, BLE, Wi-Fi, LBS.

TIP Please comply with the instructions to

extend the watch life:

Don’t use & store the watch in dusty, hot, cold,

electric, chemical, areas. Please always keep the

watch and accessories dry.

Don’t drop, shake or knock the watch, Rough

handling can break it.

Clear the watch with a piece of dry cloth. Don’t

clean in chemicals, detergent.

Don’t disassemble or refit the watch as it will

void your warranty.

Using other batteries will cause unwanted

situation.

To avoid accident, never play the watch while

driving.

Please turn off the watch in aircraft and follow

any restrictions. Wireless devices can cause

interference in aircraft.

Smart

Watch

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates uses

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

•Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) information:

This device meets the government's requirements for exposure to radio waves. The guidelines are

based on standards that were developed by independent scientific organizations through periodic

and thorough evaluation of scientific studies. The standards include a substantial safety margin

designed to assure the safety of all persons regardless of age or health. FCC RF Exposure

Information and Statement the SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of

tissue. Device types: This device has also been tested against this SAR limit. This device was

tested for typical body-worn operations with the back of the device kept 10mm from face and

0mm from wrist worn. To maintain compliance with FCC RF exposure requirements, use

accessories that maintain an 0mm separation distance between the user's wrist worn and the back

of the device and an 10mm separation distance between the user's face and the front of the device.

The use of belt clips, holsters and similar accessories should not contain metallic components in

its assembly. The use of accessories that do not satisfy these requirements may not comply with

FCC RF exposure requirements, and should be avoided.



 

 

 

 

 

 

 

 

 

 

Shenzhen LCS Compliance Testing Laboratory Ltd. FCC ID: 2AUMJEV-05 LABEL AND LOCATION Personal Safety Watch Model No.: EV-05 FCC ID: 2AUMJEV-05 Size: L 1.5cm*W1.0cm Label Location This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1

 

 

Shenzhen Eview GPS Technology Agent Authorization Company: Shenzhen Eview GPS Technology Address: Rm 201, Building 1-A, Nankechuang Yuangu, Dalang, Longhua District, Shenzhen, China Product Name: Personal Safety Watch Trade Mark: N/A Model Number: EV-05 FCC ID: 2AUMJEV-05 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: 2021-08-04 Name:

Bella Wang Title:

CEO Company:

Shenzhen Eview GPS Technology

 

 

Shenzhen Eview GPS Technology

Office of Engineering Technology

Federal Communications Commission

7435 Oakland Mills Road

Columbia, MD 21046

USA

Date: 2021-08-04

Subject; Request for Confidentiality

FCC ID: 2AUMJEV-05

To Whom It May Concern,

Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we

are requesting the Commission to withhold the following attachment(s) as confidential

documents from public disclosure indefinitely.

These documents contain detailed system and equipment descriptions and are considered as

proprietary information in operation of the equipment. The public disclosure of these documents

might be harmful to our company and would give competitors an unfair advantage in the market.

Schematic Diagram

Block Diagram

Operational Description

Parts List

Tune-up Procedure

External Photos

Test Setup Photos

Internal Photos

User Manual

In additional to above mentioned documents, in order to comply with the marketing regulations

in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that

business sensitive information remains confidential until the actual marketing of newly

authorized devices, we request Short Term Confidentiality of the following attachment(s);

OR

For 45 days, pursuant to Public Notice DA 04-1705.

For 180 days pursuant to KDB 726920 D01.

It is our understanding that all measurement test reports, FCC ID label format and

correspondence during the certification review process cannot be granted as confidential

documents and this information will be available for public review once the grant of equipment

authorization is issued.

Sincerely,

Signature:

Name: Bella Wang

Title: CEO



 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Shenzhen Eview GPS Technology

WIFI Channel 12 and 13 Declaration Letter

We declare the equipment identified below with regards to Channel 12 and 13 capabilities for

FCC ID: 2AUMJEV-05

Declaration

Product hardware does not have the capability to operate on Channel 12 and 13.

Product hardware has the capability to operate on Channel 12 and 13. However,

these two channels will be disabled via software and will not be accessible to user.

Product hardware has the capability to operate on Channel 12 and 13. However, all

the operated channels can’t be changed in the RF parameter via software. All

channels have complied with all of the requirements sets out in FCC Part 15.247.

Product hardware has the capability to operate on WiFi Channel 12 and 13, and

meets the requirements of KDB 594280 D01 v02r01. Please note:

1.) By default, this device operates in a mode that is compliant with the U.S.

requirements.

2.) This device will also use supplemental information such as geo-location data

to determine that it is operating outside the U.S., if necessary, to change its

power. Such supplemental data will be derived from the following:

Global Navigation Satellite System (GNSS)7 sensors in the device

Mobile Country Code (MCC),8 or MCC with a Mobile Network code (MNC), received

from a CMRS9 carrier and received directly by a receiver on the device

Country information derived from multiple adjacent access points (for example using

IEEE Std 802.11d provisions) may be permitted on case-by-case basis

Other suitable geo-location data based on IP addresses or other reliable source.

Name / Title: Bella Wang / CEO

Signature:

Tel: 86-15899795842

Email: sales@eviewltd.com

Date: 2021-08-04

Page 1 of 1

Rev.2.0