(==) (al (1
(ER) ==} (8 ALI Return Button LCD Display Power button Dust Box /
Water Tank Push Button PCO}
eo O68 e200 C8 0 6 Start Auto Cleaning Adjust suction power level in Auto Cleaning Mode Start Auto Cleaning Stop Cleaning Schedule Auto Cleaning start time Mode Switching:
Spot Cleaning Mode Single Room Cleaning Mode Edge Cleaning Mode Control deaning direction manually Adjust the hour and minute Adjust time Return to Charging Base Install the side brushes before use.
) _ harging your robot Place the robot on the harging _ock for battery charging
(hen charging, indication light is flashing. ight will stay light Up when charging is finished. ormal charging time Is about We.
. 2. Spot Cleaning
+ Robot intensively cleans a specific area in a spiral pattern within the 5 ft radius useful if there is a concentrated area of dust or debris.
+ Press @ onthe Remote andset repeatedly, unti the icon of Spot Cleaning Mode is displayed on the screen
@H ti}
se, 3. Edge Cleaning
+ Robot reduces the moving speed when detects a wall and then followsthe wall to ensure the edge is cleaned thoroughly. Robot will return to the Charging ock when finish.
+ Press @ on the Remote andset repeatedly, until the icon of Edge Cleaning Mode is displayed on the screen
iS 4, Single Room Cleaning Seleot this mode only when one specific room needs to be cleaned. Make sure to confine Robot to the room by Closing the door. Robot will also clean the edges before finish. Press @ on the Remote andset repeatedly unt the icon of Single Room Cleaning Mode is displayed on the screen 5. Manual Cleaning You can direct Robot to clean a particular area by using the directional buttons on the Remote andset. cael >
BO ws Set Sot a Scheduled Clear Set Time and Scheduled Cleaning 1, Press @on the Remote _andset. The time will blink on the display 2.Press @D@W tosetthe hour and minute 3.Press @ to save the setting, S$ S$
ove ove
+ You can schedule Robot to stat cleaning ata speciod time
+ To cancel a previously scheduled cleaning, press and hold @ for 3 seconds 1. Press @ on the Remote _andset. The time will blink on the display 2,Press @DA@W tosetthe hour and 3.Press @ _tosave the setting minute ppen the water inflow hole cover, in ect water slowly into the Replace the dust bo of the robot with water tank. Mopping i water tank, ready. Take out the mopping cloth and piace it on top of the water tank, Press the mopping cloth gently to ensure it stick firmly ith water tank. Clean the Dust 0 and Filters For optimal performance, follow the instructions below to clean 1. Press the ust Bo release button to pull the ust Bo ou!
land maintain Robot reguiarly. The cleaning/replacement frequency Sa ere alan Te nen Recommended caningheplacament frequency Ca 2. Open and empty the ust Bo 3. Take out the foam filter and high-performance filter liz. 4, Clean the Dust Box and filters with a vacuum cleaner ora cleaning brush, 5, Use water to rinse the primary fter screen 6. The dust box can be scrubbed clean with dishcloth,
$e 7. Dry the dust box and filter assembly, and keep the robot dry to ensure its service life. xf 8. Put the filters and pre-fiter back together in the Dust Box. o-e eS 1. Press the ater Tank release button to pull he ater = se water to clean the mopping cloth Tank out, i;
Cee W 38 Sy 3. Open the water inflow hole co er and emply water from 6.The _ater Tank can be dried with dry cloth or let it naturally ater Tank dry with air. Clean the Rolling Brush Pullon the release tabs to unlock the brush guard as shown,
@ Lift the rolling brush to remove, Clean the rolling brush with the provided cleaning tool or a vacuum cleaner. Reinstall the rolling brush by inserting the fixed protruding end first and then clicking into place, Press down to snap the brush guard into place Clean the Side Brushes Foreign substances, such as hair, can easily get tangled in the side brushes, and dirt may adhere to them, Be sure fo clean them regularly Remove the side brushes Carefully unwind and pul off any hair or sting that is wrapped between the main unit and the side brushes Use a cloth dampened with warm water to remove dust Frcriy aw Saiieie cr to endiy rechanca tech, Replace the Side Brushes The side brushes may become bent or damaged after being used for a period of time. Follow the instructions below to replace them Pull off the old side brushes and snap the new ones into place Clean the Sensors and Charging Pins To maintain the best performance, clean the drop sensors and Clean drive wheels and omnidirectional whee charging pins regularly. Dust off the drop sensors and charging contact pins using a cloth or cleaning brush. A Clean up charging dock pins Clean the downeview sensor Product Parameter