CHT909BT BLUETOOTH TOWER SPEAKER SYSTEM user manual

 

TOWER STEREO SYSTEM TOWER STEREO SYSTEM Owner's Manual PLEASE READ BEFORE OPERATING THIS EQUIPMENT. Model: CHT 909BT

-

POWER SOURCE Insert the AC plug into a conveniently located AC outlet having AC 120V~60Hz. NOTE: The AC plug supplied with the unit is polarized to help minimize the possibility of electric shock. If the AC plug dose not fit into a non polarized AC outlet, do not file or cut the wide blade. It is the user's responsibility to have an electrician replacing the obsolete outlet. INSTALLATION 1. Remote Sensor 2. Speakers 3. Speaker Net 4. Wooden Base 5. Screws 6. Washers 3 1 2 6 4 5 Figure1 Figure 2 Note:

1.The speaker net can be taken out and reassembled as Fig.1 above. 2.Assemble the wooden base to the main body with the supplied screws and washers as Fig.2 above. LOCATION OF CONTROLS MAIN UNIT 1.ST/MO (Stereo/ Mono) button 2.SOURCE button 3.VOL- (Volume Down) button 4.VOL+ (Volume Up) button 5.AUX IN 2 jack 6. / TUNE+ button 7. / TUNE- button 8. (Play/Pause) button 9. POWER button 10.Indicator 11. FM Antenna 12.AUX IN 1 jacks 13.POWER ON/OFF switch 1 2 3 4 10 9 INDICATOR AUX IN 2 ST/MO SOURCE VOL-

VOL+

POWER TUNE-

TUNE+

5 6 8 7 ANT L R AUX IN 1 OFF ON POWER 11 12 13 AC 120V~ 60Hz LOCATION OF CONTROLS REMOTE CONTROL 1 2 3 1 POWER 2 3 TUNE-

SOURCE TUNE+

VOL EQ ST/MO 4 5 6 7 8 9 1. POWER button 2. / TUNE - button 3. VOL (Volume)+/- buttons 4. SOURCE button 5. (Mute) button 6. / TUNE+ button 7 (Play/Pause) button 8 ST/MO (Stereo/ Mono) button 9 EQ (Equalizer) button 5 BATTERY INSTALLATION--- REMOTE CONTROL

-First Time Use Remove and discard the insulation tab as figure on the right

-Replacing Batteries For Remote Control 1. Push and slide out the battery holder as figure 1 below. 2. Replace the battery with a new CR2025 button cell as the polarity markings on the rear of the Remote Control. 3. Close the battery holder. Fig.1 Fig.2 Fig.3 BATTERY PRECAUTIONS EFFECTIVE DISTANCE OF REMOTE TRANSMITTER Remote Sensor, on the front of main unit Approx.15 feet GENERAL OPERATIONS 1. Insert the AC plug into a conveniently located AC outlet having AC 120V~60Hz. 2. Move POWER ON/OFF switch on the rear of the unit to ON position to switch the unit to Standby mode and the indicator will turn Red. 3. Press Power button on the unit or remote control to power on the unit. The Red Standby indicator will turn off. The Source indicator will light. 4.Press the SOURCE button repeatedly to switch to desired mode.The Source Indicator will turn corresponding color as below:

to

~ Green: Radio

~ Blue: Bluetooth

~ Purple: AUX IN 1

~ Orange: AUX IN 2 5.During Playback:

~ Press the VOL (Volume) buttons to adjust volume level as desired.

~ Press EQ button repeatedly to select and set equalizer mode as desired.

~ Press (Mute) button on the Remote Control to turn off the sound. Press again to resume. 6.When finished listening, press Power button to power off the unit. The indicator will turn Red. NOTE:

Press the POWER ON/OFF switch to OFF position use the unit. to shut off the unit if long period of time will not 7 LISTEN TO FM RADIO 1.Power on the unit as previous procedures. 2.Press the SOURCE button repeatedly until the color of the indicator turns Green. 3.Press and hold the /TUNE - or /TUNE + buttons until the indicator start blinking. The unit will start to search next (or previous) available FM radio station then plays. 4.Repeat the same procedures until the desired radio station are received. 5.If the received FM stations are in stereo mode, the unit will play in stereo mode automatically.. If reception is weak, press ST/MO (Stereo/Mono) button to turn the unit to mono mode. Press again to shift to stereo mode. FM Antenna The Antenna wire on the rear of the unit is for radio reception. If reception is weak, unwind and extend the wire or relocate the wire to improve the radio reception. LISTEN TO TV/DVD/VCR/DVR Audio out jacks on TV/DVD/ VCR/DVR White Red L R AUX IN 1 AUX IN 1 AC 120V~ 60Hz DVD 1. Connect one end of RCA audio connection cable (not supplied) to the AUX IN 1 jacks on the rear of the unit as the figure above. 2. Connect the other end to the AUX out jacks on the external player (such as Television, VCR, DVD Player, DVR ... etc.). 3. Power on the unit as previous procedures. 4. Press SOURCE button repeatedly until the indicator turns Purple. 5. Play the music in the external player as usual. (Make sure the volume output level of the player is in high level. Otherwise, sound from this unit is weak). 8 LISTEN TO EXTERNAL AUDIO DEVICES INDICATOR AUX IN 2 ST/MO SOURCE VOL-

VOL+

POWER TUNE-

TUNE+

AUX IN 2 jack INDICATOR AUX IN 2 1. Connect one end of supplied audio connection cable to the AUX IN 2 jack on the top of the unit. 2. Connect the other end to the AUX out/Line out/Phone jack on the external player (such like iPod, iPhone, iPad, MP3 player, Discman... etc.). 3. Power on the unit as previous procedures. 4. Press SOURCE button repeatedly until the indicator turns Orange. 5. Play the music in the external player as usual. (Make sure the volume output level of the player is in high level. Otherwise, sound from this unit is weak). 9 BLUETOOTH PARING AND PLAYBACK 1. Power on the unit as previous procedures. 2. Press the SOURCE button on the unit or remote control until the indicator turns blue. 3. Turn on the BT function on the external BT device and play the music as usual. (Make sure the volume level of the external BT device is set to high level). 4. During palyback:

Press the VOL (Volume) +/- buttons to adjust volume level. Press the / TUNE- or / TUNE + button to skip track. Press the (Play/Pause) button to pause. Press again to to resume normal playback. NOTES:

During the first time use, pair the external BT device as below:

1. Power on the unit as previous procedures and press the SOURCE button repeatedly until the indicator turns blue and blinking. 2. Power on the external BT device and enter searching mode. Start paring as the on screen instructions on the external BT player(For detailed paring procedures, please refer to the user's manual of your BT device.) 3. When the external BT player searched the Speaker, our model number"CHT-909BT" will appear on the display of the external BT device. 4. Paring code"0000" may need to enter. 10 TROUBLESHOOTING GUIDE Check the followings before requesting service SYMPTOM POSSIBLE CAUSE POSSIBLE SOULTION No power AC plug not connected to the Plug to the wall outlet. wall outlet Volume in minimum position Raise volume level by pressing the VOL

(Volume) + button No sound The connected device is not in payback mode Play the music/movie in the connected device as usual and make sure the volume level of it is in high level Input source incorrect Press the SOURCE button repeatedly to set the input source to the desired mode Sound distortion Remote not working Bluetooth reception failure Bass level of the connected device too high Reduce the bass level of the connected device Volume level too high Reduce the volume level by pressing the VOL (Volume- )-button

-

The batteries are consumed Replace with new battery The external device is far from the unit Put the external BT device close to the unit Have not paired Pair both unit as BT pairing page 11 GENERAL SPECIFICATIONS Power Source...........................................................................................................AC 120V~60Hz Power Consumption...................................................................................................................45W Radio Coverage................................................................................................FM 87.5 -108.0 MHz Impedance of Speakers:

Loud Speakers .......................................................................................................8 Ohm, 10W x 2 Tweeters................................................................................................................... 8 Ohm, 5W x 2 Bluetooth Working Distance......................................................................................... Up to 30 feet and structures may affect the effective range) Remote Working Distance.............................................................................................Up to 15 feet

(Measured in open area. Wall Accessories 1 x User Manual 1 x Remote Control, using CR 2025 button cell (Already installed in the remote control) 1 x Stereo Audio Connection Cable with 3.5 stereo plug 2 x Assembly Screws / Washers 1 x Wooden Base 12 LIMITED WARRANTY Craig warrants this product to be free from manufacturing defects in material and workmanship under normal use for a period of 90 days from date of purchase. If service is required, please return the product to the store where it was purchased for exchange;

or, pack the unit in the original packing material with all accessories if applicable, a copy of your sales receipt and a Cashiers check or Money Order for $20.00 (to cover shipping and handling costs) payable to Craig Electronics Inc. For consumers in Canada, please make sure that the cashier check or money order is redeemable through a U.S. bank. Ship your product freight pre-paid. Your unit will be repaired, replaced or if the unit can not be repaired or replaced, a refund will be forwarded to you within four weeks of receipt of your unit. Please ship your unit to:

Craig Electronics Inc. 1160 NW 163 Drive Miami, Fl 33169 This warranty is void if the product has been: a) Used in a commercial application or rental. b) Damaged through misuse, negligence, or abuse. c) Modified or repaired by anyone other than an authorized Craig service center. d) Damaged because it is improperly connected to any other equipment. Note: This warranty does not cover: a) Ordinary adjustments as outlined in the Owners Manual which can be performed by the customer. b) Damage to equipment not properly connected to the product. c) Any cost incurred in shipping the product for repair. d) Damage to the product not used in the USA. This warranty is not transferable and only applies to the original purchase. Any implied warranties, including the warranty of merchantability, are limited in duration to the period of this expressed warranty and no warranty whether expressed or implied shall apply to the product thereafter. Under no circumstance shall Craig be liable for any loss or consequential damage arising out of the use of this product. This warranty gives specific legal rights. However, you may have other rights which may vary from state to state. Some states do not allow limitations on implied warranties or exclusion of consequential damage. Therefore, these restrictions may not apply to you. To Obtain Service on your Product email:service@craigelectronics.com Printed in China CHT910-IB-E0CL1-B0US