| submitted | available | document details (if available) | source link |
|---|---|---|---|
| CHT917BT IB English.cdr Administrator Corel PDF Engine Version 14.0.0.653 |
| various | Manual | Users Manual | 4.57 MiB |
FCC Warnings WARNING:Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC NOTICE:
To assure continued compliance, follow the attached installation instructions and use only shielded cables when connecting to other devices. Modifications not authorized by the manufacturer may void users authority to operate this device. Insert the small plug from supplied AC/DC adaptor to DC IN jack on the rear of the unit and insert the AC/DC adaptor to the wall outlet having AC 100-240V~, 50/60 Hz. NOTE:This AC/DC Adapter is intended to be correctly orientated in a vertical or floor mount position. AC/DC adapter To the DC IN jack on the rear of unit. 1. Placing on the table When placing the Sound Bar on an entertainment center, bookshelf, or any type of enclosed space, be sure to allow at least 2-3 inches of space around the Sound Bar for ventilation. If the Sound Bar is enclosed in a tight space, without ventilation, heat generated from the Sound Bar could produce a potential heat hazard. 2. Mounting the Speaker Bar onto a wall We recommend having this speaker professionally mounted. By using the included wall mounting accessories, the sound bar can be mounted onto a wall. Distance Between Two Brackets 22.9 inches 2.1 Mounting on the wooden wall You may use 22.9 inches 2 pieces screws
(Included) 1. Mark the position of the mounting screws on the wall using a pencil. 2. Drill the supplied screws directly into the marks that you have made on the wall and leave approx. 0.3 inch length to hook the sound bar. 3. Put the sound bar onto the mounting screws. Make sure they are firm and stable. 2.2 Mounting on the wall l:
You may use 2 pieces screws
(Included) 2 pieces plastic inserts
(Included) 1. Mark the position of the mounting screws on the wall using a pencil. 2. Drill 2 x 7/32 inch diameter holes by a powerful electric drill ( Not Supplied ). 3. Insert the supplied plastic inserts into the holes by hammer .
( Not Supplied ) 4. Secure the supplied screws into the plastic insert and leave approx. 0.3 inch length to hook the sound bar. 5. Put the sound bar onto the mounting screws. Make sure they are firm and stable. 22.9 inches
(1)
(2) 4 2
. 2 M o u n t i n g o n t h e w o o d e n w a l Front View 1.Remote Sensor 2. LCD Display Top View and Back View 3.Speakers ANT AUX 2 L R AUX 1
-
VOL
+
SOURCE DC IN DC 16V, 3A ANT AUX 2 L R AUX 1
-
VOL
+
SOURCE DC IN DC 16V, 3A 11 10 9 78 6 5 4 4. DC IN jack 5. ( Mute ) button 6. SOURCE button 7. Standby button 8. AUX 1 jacks 10. AUX 2 jack 9. VOL ( Volume ) + and - buttons 11. ANT ( Antenna ) 5 1 2 3 4 5 6 7 8 9 CH+
TUNE-
M TUNE+
SLEEP CH-
EQ MO/ST SOURCE CLOCK BASS -
TREBLE-
VOL-
BASS+
TREBLE+
VOL+
10 11 12 13 14 15 1. CH+/ ( Channel Up ) 2. Power 3. TUNE + / ( Tune or Skip Forward ) 4. TUNE - / ( Tune or Skip Backward ) 5. M/ ( Memory/Play/Pause ) 6. SLEEP 7. CH - / ( Channel Down ) 8. MO/ST ( Mono/Stereo ) 9. BASS +/-
10. ( Mute ) 11. EQ ( Equalizer ) 12. CLOCK ( Set ) 13. SOURCE 14. VOL ( Volume ) +/-
15. TREBLE +/-
6
-First Time Use Remove and discard the insulation tab as figure on the right
-Replacing Batteries For Remote Control 1. Push and slide out the battery holder as figure 1 below. 2. Replace the battery with a new CR2025 button cell as the polarity markings on the rear of the Remote Control. 3. Close the battery holder. Fig.1 Fig.2 Fig.3 BATTERY PRECAUTIONS Remote Sensor 30 30 7 GENERAL OPERATIONS TIME SET OR RESET:
1. Connect the unit to the power as previous procedures. 2. Make sure the unit is in Standby mode, then press and hold the CLOCK button on the remote control. The digit of hour will blink. 3. Press the or button repeatedly to set hour . ( Make sure PM indicator appear on the display if the time is PM and not appear if the time is AM ). 4. Press the CLOCK button again, the digit of minute will blink. 5. Press the or button to set minute. 6. When finished, press the CLOCK button again to save the settings and exit. The LCD Display will turn on. PPPPPPPPP SLEE TIMER:
In power on mode, press the SLEEP button on the remote control repeatedly to activate and set the sleep time of the sleep timer. " " will appear on the display. To turn off the Sleep Timer before times up, press the SLEEP button repeatedly to reset the sleep time to "OFF". 8 GENERAL OPERATIONS 1. Connect the AC/DC adapter to the unit and wall outlet as the previous procedure . The LCD display will turn on. switch to desired mode. 2. Press the Power button on the unit or remote control to power on the unit from standby mode. 3. Press the SOURCE button repeatedly to 4. During Playback:
~ Press the VOL ( Volume ) + or - buttons to adjust volume level as desired.
~ Press the EQ button repeatedly to select and set equalizer mode as desired.
~ Press ( Mute ) button to turn off the sound. Press again to resume.
~ Press the BASS +/- buttons to adjust the sound level of bass.
~ Press the TREBLE +/- buttons to adjust the sound level of treble. 5. When finished listening, press the Power button on the remote control or unit to power off
( Standby mode ) the unit. 6. If long period of time will not use the unit, unplug the AC/DC Adaptor from the wall outlet. LISTEN TO FM RADIO 1. Connect the Sound Bar to the power as previous procedures. 2. Press the Power button on the unit or remote control to power on the unit. 3. Press the SOURCE button on the unit or remote control repeatedly until FM Frequency shows on the LCD Display to turn to Radio ( FM ) mode. 4. In first time use:
~ Press and hold the / TUNE - or /TUNE + buttons approx. 1 second, then release to start auto searching the next or previous available station.
~ When the available FM station is searched, the unit will stop search then start playback.
~ Press the M/ button to enter to memory mode, the current program number will appear on the display and blink.
~ Press the CH ( Channel ) + or - buttons on the remote control repeatedly to desired program number then press the M/ button to stored it.
~ Repeat the same procedures until all the desired available FM stations were stored.
( Total 20 stations can be programmed.) 5. After programmed, press the CH + or - buttons to selected the desired programmed channel. NOTE: If the AC power is cut off or failure, the stored program may be erased. Reset again as above procedures. 6. If reception no good, press the or buttons repeatedly to fine tune. 7. Press the MO/ST (Mono/Stereo) button repeatedly to set to Mono or Stereo mode as desire. FM Antenna The Antenna wire on the rear of the unit is for radio reception. If reception is weak, unwind and extend the wire or relocate the wire to improve the radio reception. 9 BLUETOOTH PARING AND PLAYBACK BT ( Blue Tooth ) BT ( Blue Tooth ) In first time use or re-pairing to new BT Device, pairing the unit to external BT Device as follows:
1. Power on the unit as previous procedures. 2. Press the SOURCE button repeatedly until BT appears on the display and blink. 3. Power on the external BT Device and enter to searching mode. Start pairing as the on screen instructions on the external BT Device. After paired, blinking.
( For details pairing procedures, please refer to the user's manual of your BT Device.) BT on display will stop Notes:
1. When the external BT player searched the unit, our model number
"CHT923" will appear on the display of external BT device. 2. Pairing code "0000" may need to enter. Normal operation after paired:
1. Power on the unit and selected the playback source to BT as previous procedures. 2. Turn on the BT function of the external BT Device. 3. Wait a few seconds until the unit paired to the external BT Device automatically.
( BT on display will stop blinking ). 4. Play the music in the connected BT Device as usual. 5. During playback:
--Press the button to pause; press again to resume normal playback.
--Press the /TUNE - or / TUNE + buttons to skip tracks. 10 AUX 1 : LISTEN TO TV/DVD/VCR/DVR 1. Connect the Aux out jacks from the external audio player (such like TV, DVD player, VCR etc.) to the AUX 1 jacks on the rear of unit by the supplied RCA Connection Cable as the figure below:
To Audio Out Jacks DVD white red ANT AUX 2 L R AUX 1 DC IN DC 16V, 3A 2. Connect the Sound Bar to the power as previous procedures. 3. Press the ( ) Power button to power on the unit. 4. Press the SOURCE button repeatedly until " AUX 1" appear on display. 5. Power on the connected external player and start playback music as usual. AUX 2 : LISTEN TO EXTERNAL AUDIO DEVICES 1. Connect the Headphone/Earphone; Line out jacks from the external audio player
(such like MP3 player; Discman etc) to the AUX 2 jack on the rear of unit by the supplied Audio Connection Cable as the figure below:
ANT AUX 2 UX 2 L R AUX 1 DC IN DC 16V, 3A Audio Player To Phone Jack 2. Connect the unit to the power as previous procedures. 3. Press the ( ) Power button to power on the unit. 4. Press the SOURCE button repeatedly until " AUX 2" appear on display. 5. Power on the connected external player and start playback music as usual. 11 TROUBLESHOOTING GUIDE Check the followings before requesting service SYMPTOM POSSIBLE CAUSE POSSIBLE SOULTION No power Power AC/DC adapter not connected Connect the power AC/DC adapter The unit is in Standby mode Press button to turn on the unit Volume in minimum position No sound The connected device is not in payback mode Raise volume level by pressing the VOL
(Volume) + button Play the music/movie in the connected device as usual and make sure the volume level of it is in high level Input source incorrect Press the SOURCE button repeatedly to set the input source to the desired mode Bass level of the connected device too high Volume level too high Reduce the bass level of the connected device. Press the BASS - button on the Sound Bar to reduce bass level. Reduce the volume level by pressing the VOL (Volume ) - button The battery is consumed Replace with new battery The external device is far from the unit Put the external BT device close to the unit Have not paired Pair both units as BT pairing page Sound distortion Remote not working Bluetooth reception failure 12 Power Source........................................................................................ DC 16V; 3A, Radio Coverage.............................................................................................FM 87.5 -108.0 MHz
---
Impedance of Speakers:
Loud Speakers Woofer
........ .......................................................................... 8 Ohm,10 W x 2
........................................................................... 8 Ohm,15 W x 2 Bluetooth Effective Range in Open Aera....................................................................Up to 32 feet Remote Effective Range..........................................................................................Up to 16 feet 1 x AC/DC Adaptor ( Input: AC 100-240V~ 50/60Hz; 1.4A Max. Output: DC 16V; 3 A, ) 1 x Remote Control, using CR 2025 button cell ( Included, already installed in remote control ) 1 x Stereo Audio Connection Cable with 3.5mm stereo plugs 1 x RCA Connection Cable 1 x User's Manual 2 x Plastic Inserts ( For Wall Mount ) 2 x Metallic Screws ( For Wall Mount )
---
13 LIMITED WARRANTY Craig warrants this product to be free from manufacturing defects in material and workmanship under normal use for a period of 90 days from date of purchase. If service is required, please return the product to the store where it was purchased for exchange;
or, pack the unit in the original packing material with all accessories if applicable, a copy of your sales receipt and a Cashiers check or Money Order for $15.00 (to cover shipping and handling costs) payable to Craig Electronics Inc. For consumers in Canada, please make sure that the cashier check or money order is redeemable through a U.S. bank. Ship your product freight pre-paid. Your unit will be repaired, replaced or if the unit can not be repaired or replaced, a refund will be forwarded to you within four weeks of receipt of your unit. Please ship your unit to:
Craig Electronics Inc. 1160 NW 163 Drive Miami, Fl 33169 This warranty is void if the product has been: a) Used in a commercial application or rental. b) Damaged through misuse, negligence, or abuse. c) Modified or repaired by anyone other than an authorized Craig service center. d) Damaged because it is improperly connected to any other equipment. Note: This warranty does not cover: a) Ordinary adjustments as outlined in the Owners Manual which can be performed by the customer. b) Damage to equipment not properly connected to the product. c) Any cost incurred in shipping the product for repair. d) Damage to the product not used in the USA. This warranty is not transferable and only applies to the original purchase. Any implied warranties, including the warranty of merchantability, are limited in duration to the period of this expressed warranty and no warranty whether expressed or implied shall apply to the product thereafter. Under no circumstance shall Craig be liable for any loss or consequential damage arising out of the use of this product. This warranty gives specific legal rights. However, you may have other rights which may vary from state to state. Some states do not allow limitations on implied warranties or exclusion of consequential damage. Therefore, these restrictions may not apply to you. To Obtain Service on your Product email:service@craigelectronics.com Printed in China CHT923_WC_E0CL1_H0US Size: 148.5(W) x 210(H)mm (A5)
This product uses the FCC Data API but is not endorsed or certified by the FCC