submitted | available | document details (if available) | source link |
---|---|---|---|
ITSB-340-Manual-012215-lores Adobe PDF library 9.90 |
various | User Manual | Users Manual | 2.83 MiB |
2.1CH TV Stand Bluetooth Sound Base Speaker MODEL:ITSB-350 1 X Remote Control 1 X Instruction Manual 1 X RCA Cable 1 X 3.5mm Aux In Cable Press the button on the unit or press the SOURCE button on the remote control repeatedly until "BT"appears on display. ITSB-350 ITSB-350 optical in. Optical-In 14 FRONT VIEW 1 TOP VIEW 2 3 4 5 6 7 8 9 10 REAR VIEW OPTICAL OPTICAL 11 12 13 14 1. SPEAKER 2. DISPLAY 3. REMOTE SENSOR 4. POWER Button 5. SOURCE Button 6. PLAY/PAUSE/PAIR Button 7. TUNE DOWN/PREVIOUS Button 8. TUNE UP/NEXT Button 9. VOLUME DOWN Button 10. VOLUME UP Button 11. DC IN JACK 12. AUX IN JACKS(L/R) 13. OPTICAL IN JACK 14. ANTENNA WIRE 1. Connect the Aux out jacks from the external audio player (such like DVD player, VCR etc.) to the AUX IN jacks on the rear of the unit by the supplied RCA connection cable as the figure below:
OPTICAL white red
(DVD or VCR...etc) 2. Connect the unit to the power as previous procedures. 3. Press the Standby ( ) button on the unit or Remote Control to power on the unit. 4. Press the button on the unit or press the SOURCE button on the Remote Control repeatedly until "AUX" appears on display. 5. Power on the connected external player and start playback music as usual. STANDBY PAIR TUNE-
TUNE+
FM SCAN MO/ST PRE/
RECALL 10 11 12 13 1 2 3 4 5 6 7 8 9 2. VOL(volume)- Button 3. SOURCE Button 4. PAIR Button 5. EQ (equalizer) Button 6. TUNE- Button 7. Button 8. FM SCAN Button 9. MO/ST(Mono/Stereo) Button 10. MUTE Button 11. VOL(volume)+ Button 12. TUNE+ Button 13. PRE/RECALL Button PLAYING AUDIO VIA OPTICAL-IN SOURCE 1. Connect the Optical out jack from the external audio Player (such like TV, DVD Player OPTICAL IN jack on the top of unit by the Optical Connection BD Player etc.) to the Cable (not supplied) as the figure below: ( F or PCM format only ) OPTICAL Rear view of the unit Optical Connection Cable ( not supplied ) TV; DVD player; BD player... etc. 2. Power on the unit as previous procedures. 3. Press the button on the unit or press the SOURCE button on the Remote Control repeatedly until "OPTI" appears on display. 4. Power on the connected external player and start playback the Music as usual. Turn on the digital audio output and set it to PCM (Plus Code Modulation) type similar to the follows figure:
Picture AudioAudio Time Setup Lock Off Sound Mode Bass Treble Balance Surround AVL Digital Output Digital Output Audio Language Standard Off Off PCM PCM English Select Move MENU Exit The TV STAND SOUND BASE Press the button on the unit or press the SOURCE button on the remote control repeatedly until "BT"appears on display. SOUND BASE the TV STAND the TV STAND SOUND BASE ITSB-350 ITSB-350 ITSB-350 ITSB-350 2) Press the button on the unit or press the SOURCE button on the Remote Control repeatedly until FM frequency appears on display. 3) Press /TUNE- or /TUNE+ button on remote control(or press If you want to connect another BT device remote control or press and hold the Button on the unit to cut off current pairing, then try to connect the other BT device following above steps. while playing, press "PAIR" Button on to search the specific or button on the unit) repeatedly band. Press and hold the TUNE - or TUNE + button on remote control
(or press and hold the or button on the unit), the unit will search then stop and play). automatically the To store the band automatically, press FM SCAN button on remote control , the unit will scan all available band and store automatically. available band back and forth 4) 5) After finishing scanning, press "PRE/RECALL" button on remote control repeatedly to select and listen the desired preset channels.
~ Press the EQ button on the remote control to set to JAZZ, POP, ROCK, CLAS and NORM mode. Press the /TUNE + or /TUNE - button to skip the tracks. button on the remote control on the unit to pause, press again to resume. or press the button
~
~ Press the Folloe these precautions when using a battery in this device:
1. Use only the size and type of battery specified. 2. Be sure to follow the correct polarity when installing the battery as indicated in the battery compartment. A reversed battery may cause damage to the device. 3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc ) or old batteries with fresh ones. 4. If the batteries in the device are consumed or device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. 5. Do not try to recharge the battery not intended to be recharged; it can overheat and rupture.
( Follow battery manufacturer's instructions.) 6. The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. 7. Clean the battery contacts and also those of the device prior to battery installation. 8. This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burn in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. 6) If the available FM station is stereo, the unit will plays it in stereo mode automatically. If the reception is no good, press the MO/ST button on the Remote Control to switch it to Mono mode. Press again to turn back to Stereo mode. 20 3 60 Type of Optical Digital Audio in ........................................................................ PCM is a trademark on a registered trademark of Bluetooth SIG Inc. All other trademarks and trade names are those of their respective owners. FCC Warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. RF Exposure Statement To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body:
Use only the supplied antenna. or +
correct source appears or -
6
This product uses the FCC Data API but is not endorsed or certified by the FCC