all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Users Manual | Users Manual | 3.34 MiB | February 11 2018 | |||
1 | Cover Letter(s) | February 11 2018 | ||||||
1 | Cover Letter(s) | May 11 2018 / February 11 2018 | ||||||
1 | External Photos | February 11 2018 | ||||||
1 | Internal Photos | February 11 2018 | ||||||
1 | ID Label/Location Info | February 11 2018 | ||||||
1 | Cover Letter(s) | February 11 2018 | ||||||
1 | RF Exposure Info | February 11 2018 | ||||||
1 | Test Report | February 11 2018 | ||||||
1 | Test Setup Photos | February 11 2018 |
1 | Users Manual | Users Manual | 3.34 MiB | February 11 2018 |
Nostalgia 6 in 1 Turntable Radio MODEL:SRCD838BT INSTRUCTION MANUAL PLEASE READ CAREFULLY BEFORE OPERATION IMPORTANT SAFETY INSTRUCTIONS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product`s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance(servicing) instructions in the literature accompanying the appliance. DANGER:
Invisible and hazardous laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam. FCC NOTICE:
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC ID: OKUSRCD838BT To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. Changes or modifications made to this equipment not expressly approved by (manufacturer name) may void the FCC authorization to operate this equipment It has been designed in such a way that it does not require a safety connection to electrical earth. FCC WARNING:
To assure continued compliance, follow the attached installation instructions and use only shielded cables when connecting to other devices. Modifications not authorized by the manufacturer may void user`s authority to operate this device. RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION:
THIS DIGITAL VIDEO DISC PLAYER EMPLOYS A LASER SYSTEM. TO ENSURE PROPER USE OF THIS PRODUCT. PLEASE READ THIS OWNER`S MANUAL CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONT ACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE. USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOT STARE INTO BEAM. WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. INDUSTRY CANADA CONFORMITY INDUSTRY CANADA CONFORMITY CAN ICES-3(B)/NMB-3(B) WARNING:The mains plus is used as disconnected device, the disconnect device shall remian readily operable. The equipment is Class II or double insulated electrical appliance. 2 IC Caution:
RSS-Gen Issue 5 April 2018&CNR-Gen 5e April 2018:
- English:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
- French:
Le prsentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationestautorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareildoit accepter tout brouillageradiolectriquesubi, mmesi le brouillageest susceptible d'encompromettre le fonctionnement. IMPORTANT SAFETY INSTRUCTIONS Before using the unit, be sure to read all operating instructions carefully. Please note that these are general precautions and may not pertain to your unit. For example, this unit may not have the capability to be connected to an outdoor antenna. All the safety and operating instructions should be read before the product is operated. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. All operating and use instructions should be followed. The safety and operating instructions should be retained for future reference. All warnings on the product and in the operating instructions should be adhered to. Do not use this product near water and moisture, for example: near a bathtub, washbowl, kitchen sink or laundry tub; in a wet basement; or near a swimming pool. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning. instructions. Slots and openings in the cabinet and in the back or bottom are provided for ventilation, to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should never be placed near or over a radiator or heat source. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus(including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. receptacles, and the point where they exit from the apparatus. 10)Protect the power cord from being walked on or pinched particularly at plugs, convenience 11)Only use attachments/accessories specified by the manufacturer. 12)Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. An appliance and cart combination should be moved with care. Quick stop, excessive force and uneven surfaces may cause the appliance and cart combination to overturn. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. To protect your product from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture does not operate normally, or has been dropped. 15) Power source 16) Power lines This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other source, refer to the operation instructions. An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 3 IMPORTANT SAFETY INSTRUCTIONS 17) Overloading 18) Object and liquid entry Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. Never push objects of any kind into the product through openings as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid on the product. 19) Outdoor antenna grounding If an outside antenna is connected to the product, be sure the antenna system is grounded so as to Provide some protection against voltage surges and built up static charges. Section 810 of the National Electric Code ANSI/NFPA 70 provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge product, size of grounding conductors, location of antenna-discharge product, connection to grounding electrodes and requirements for the grounding electrodes. 20)Service 21)Replacement parts 22)Safety check Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original parts. Unauthorized substitutions may result in fire or electric shock or other hazards. Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 32
)Damage requiring service Unplug this product from the wall outlet and refer service to qualified service personnel under the following conditions. a) When the power-supply cord or plug is damaged. b) c) d) If liquid has been spilled or objects have fallen into the product. If the product has been exposed to rain or water. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an adjustment of other controls may result in damage and will require extensive work by a qualified technician to restore the product to its normal operation. If the product has been dropped or the cabinet has been damaged. When the product exhibits a distinct change in performance-this indicates a need for service. e) f) 2 )Note to CATV system installer 4 This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. NOTE: Refer all servicing to qualified service personnel. Servicing is required when the unit has been damaged in any way such as the following: the power-supply cord or plug has been damaged, liquid has been spilled into unit, the unit has been exposed to rain or moisture, the unit has been dropped or the unit does not operate normally. 4 Turntable Location of Controls B C D E F A Before use, take out the stylus guard ( white plastic cover ) by pull it out. A Turntable B Screw fixing the turntable for transportation Before use, completely loosen the screw by turning it clockwise. When transport the unit again, turn the screw counterclockwise to secure the turntable. C Lever D Tone arm holder E Speed selector F Tone arm 5 Location of Controls Side View Front View VOLUME M I N O N. OFF MAX AUX IN H I J K L M N O P Cassette Eject button Speakers Function selector Tuning knob Radio dial scale Power ON/OFF-Volume knob OPEN/CLOSE button AUX IN jack Q R S T U V W X Y STOP button PLAY/PAUSE button REPEAT button LED display for CD Disc tray PROGRAM button B.SKIP and F.SKIP
(Backward and Forward skip) buttons AM/FM BAND Switch PHONE jack 6 Location of Controls Back View AC~120V 60Hz FM antenna FM antenna LINE OUT jacks LINE OUT jacks AC Power Cord AC Power Cord Open/close the turntable cover 1.Lift the turntable cover. 2.Pull the arms to front to lock it as the figure on left. 1. Lift the cover. 2. Push the arms to backward to release the lock. 3. Close the cover. 7 Listening to a Record Transportation screw VOLUME M I N O N.OFF MAX AUX IN Before use, completely loosen the transportation screw by turning it clockwise. Select the speed. Take out the stylus guard (white plastic cover). Turn the Power ON/OFF-VOLUME knob clockwise until a sound
"
click was heard to turn on the unit.
"
If plays the small size 45 rpm record, insert the supplied adaptor to the center spindle before place the record. VOLUME M I N O N.OFF MAX Turn the Function selector to the PHONO position. Step 2 Step 1 45 RPM adaptor Open the cover. Unlock the clip to release the tone arm as the figure below. clip 8 Listening to a Record 7 Raise the lever to lift the tone arm. 10 Turn the Power ON/OFF-VOLUME knob to adjust the volume. tone arm VOLUME M I N O N.O FF MAX 11 When finished listening, replace the tone arm to the rest and lock it as previous procedures. Turn the Power ON/OFF-VOLUME knob counterclockwise until a click sound was heard to power off the unit.
"
"
cue lever 8 Move the tone arm to the top of the record. The turntable will start to turn. 9 Place the tone arm to the desired point on the record by turn the lever down as the figure below. lever 9 Listening to a CD 2 1 6 8 CD Playback:
1 Turn the POWER ON/OFF-VOLUME knob clockwise until a click sound was heard to turn on the unit.
"
"
VOLUME M I N O N.OFF MAX 2 Turn the Function selector to the CD position. 3 Press the OPEN/CLOSE button to open the disc tray. 4 Place a disc on the tray with the printed label face up. VOLUME M I N O N
. OFF MAX AUX IN 3 5 4 5 Press the OPEN/CLOSE button to close the tray. A few seconds later, the total number of tracks will appear on the LED display and play will start automatically. 6 Turn the POWER ON/OFF-Volume knob to adjust volume level. VOLUME M I N O N.OFF MAX 7 During playback:
~ Press the PLAY/PAUSE button to pause, press again to resume normal playback.
~ Press the B.SKIP or F.SKIP button repeatedly to skip the tracks.
~ Press and hold the B.SKIP or F.SKIP button to fast searching the desired section.
~ To stop, press the STOP button. 8 When finished listening Turn the Power ON/OFF - VOLUME knob counterclockwise unit a
"click"
sound was heard to power off the unit. Never place more than one disc on the tray. The disc must be placed on the center of the disc tray. If the disc is not correctly loaded, it may not be possible to open the tray again once it has closed. 10 Listening to a CD Repeat Playback:
During playback:
1. Press the REPEAT button once, the Repeate indicator repeatedly until the STOP button was pressed. will light and blinking. The current track will playback 2. Press the REPEAT button twice, the Repeate indicator will light and stop blinking. All the tracks in the current disc will playback repeatedly until the STOP button was pressed. 3. To cancel the repeat function during playback, press the REPEAT button repeatedly until the Repeat indicator not light. Repeat indicator Programme Playback:
Up to 20 tracks can be programmed playback as follows:
1. In CD STOP mode, press the PROGRAM button. 01 will appear on the LED display and blinking . 2. Select the first specific track to be programmed by pressing the B.SKIP or F.SKIP buttons. 3. Press PROGRAM button again to store the selected track into the memory. 4. Repeat steps 2 and 3 until all the specific tracks stored into the memory. 5. Press the PLAY/PAUSE button to start playback. 6. To stop and cancel program playback, press the STOP button. 11 Listening to the Radio 2 4 1 5 6 VOLUME M I N O N
.OF F MAX AUX IN 3 1 Turn the Power ON/OFF-VOLUME knob clockwise until a click sound was heard to turn on the unit.
"
"
4 Turn the TUNING knob to receive the desired radio station. VOLUME M I N O N.O FF MAX 2 Turn the Function selector to the RADIO position. 5 Turn the Power ON/OFF-VOLUME knob to adjust the volume level. VOLUME M I N O N.O FF MAX 3 Slide the AM/FM band switch to AM or FM as desired. AM/FM 6 When finished listening, turn the Power ON/OFF-VOLUME knob counterclockwise until a sound 'click' was heard to power off the unit. Antennas:
AM
- This unit has a build in ferrite rod antenna, which provides adequate reception in most areas. If reception is weak, turn the unit to improve reception. FM
- The FM Antenna wire is for FM reception. If reception is weak, unwound and extended the wire or relocation the wire to improve the radio reception. 12 Listening through Bluetooth 2 1 5 VOLUME M I N O N
.OF F MAX AUX IN 1 Turn the Power ON/OFF-VOLUME knob clockwise until a
"
click sound was heard to turn on the unit.
"
VOLUME M I N O N.O FF MAX 2 Turn the Function selector to the TAPE/AUX position. The unit will say "Pairing" after a few seconds. 5 Turn the Power ON/OFF-VOLUME knob to adjust volume level. VOLUME M I N O N.O FF MAX NOTE:
1. The music control buttons are not working under Bluetooth mode. 2. During playing, DO NOT plug the AUX IN cable or insert the cassette tape, or it will switch to AUX IN or cassette tape mode. 3. The unit will search and connect last paired device automatically when both of them are in Bluetooth mode and working range. 3 4 Activate the Bluetooth function on external Bluetooth device and try to search the unit, the pairing name will appear as "SYLVANIA SRCD838BT". Select it and make connection, indication voice
"Paired" will be heard playing on your external device. when paired. Control the music 13 Listening to a Cassette Tape 2 1 4 VOLUME M I N O N
.OF F MAX AUX IN 1 Turn the Power ON/OFF-VOLUME knob clockwise until a
"
click sound was heard to turn on the unit.
"
VOLUME M I N O N.O FF MAX 4 Turn the Power ON/OFF-VOLUME knob to adjust volume level. VOLUME M I N O N.O FF MAX 2 Turn the Function selector to the TAPE/AUX position. 5 Fast forward 3 Insert a pre-recorded cassette tape into the cassette compartment until the Eject button ejected. Play will start automatically. To fast foreword to desired point, press the Eject button to half position. When finished, press the button again to resume normal playback. Note: When finish winding, please remember press the Eject button to stop winding and take out the tape. Otherwise, the unit will maintains on the winding mode. 6 To stop playback and eject the tape When finished listening, press the Eject button to stop playback and take out the tape. Turn the Power ON/OFF
-VOLUME button counterclockwise until a "Click" sound was heard to power off the unit. NOTE: During playing, DO NOT plug the AUX IN cable, or it will switch to AUX IN mode. 14 Others Connection AUX IN:
1. Connected the external audio device to the unit by an audio connection cable with 3.5mm stereo mini jacks
~ Insert one end to the Phone; Line Out or AUX Out Jack on the external audio device.
~ Insert the other end to the AUX IN jack on the front of unit. 3 2 5 VOLUME M I N O N
. OFF MAX AUX IN 1
...................................... Mobile Phone Connect to the Phones;
AUX Out; Line Out Jack of external audio devices
(Such like MP3 Player;
cell phone; iPod/iPad ... etc)
....................................... To AUX IN Jac on the unit k 2. Turn the Power ON/OFF - VOLUME knob clockwise until a "click" sound was heard to turn on the unit. 3. Turn the Function selector to the TAPE/AUX position. 4. Play the music on the connected external audio device as usual. 5. When finished listening, turn the Power ON/OFF - VOLUME knob counterclockwise until a "click" sound was heard to power off the unit. Notes:
Make sure the sound output level of the connected external audio device is in high level. LINE OUT:
1. Connected the external audio device by an audio connection cable with RCA plugs
~ Insert one end to the Line IN or AUX IN jacks on the external audio Amplifier.
~ Insert the other end to the LINE OUT jacks on the rear of unit. AC~120V 60Hz To the Line In/AUX In jacks on the external audio Amplifier
(Connection Cable not included) 15 2. Turn the Power ON/OFF - VOLUME knob clockwise until a "click" sound was heard to turn on the unit. 3. Plays the music/radio as previous procedures. Sound will hearing from the connected external audio Amplifier system. Adjust the
(If do not want to hearing the sound from this unit at the same time, turn the Power ON/
knob to minimum position). volume level by the volume control on the connected external Amplifier. OFF - VOLUME 4. When finished listening, turn the Power ON/OFF - VOLUME knob counterclockwise until a "click" sound was heard to power off the unit. Phones jack:
For private listening, connect a headphone / earphone (not included) unit. The speakers will be disconnected when headphone / earphone is inserted into the jack. into the PHONE jack on the front of About Disc Discs which can be played on this unit:
Conventional audio CDs bearing the CD-DA logo on the label:
Do not expose discs to direct sunlight or high humidity and temperature for extended periods. Long exposure to high temperatures will warp the disc. Properly finalized CD-R and CD-RW discs. Always place the disc on the disc tray with the label side up.
(Compact discs can be played or recorded only on one side.) To remove a disc from its storage case, press down on the center of the case and lift the disc out, holding it carefully by the edges. How to remove the disc How to hold the disc Should the disc become dirty, wipe the surface radially (from the center hole outward towards the outer edge) with a soft, dry cloth:
Never use such chemicals as record sprays, antistatic sprays or fluid, benzine or thinner to clean the discs. Such chemicals will do irreparable damage to the discs plastic surface. Discs should be returned to their cases after use to avoid dust and scratches that could cause the laser pickup to skip. Do not play any disc that is warped, deformed or damaged. Playing such discs may cause irreparable harm to the playing mechanisms. CD-R and CD-RW discs are more sensitive to the effects of heat and ultraviolet rays than ordinary CDs. It is important that they are not stored in a location where direct sunlight will fall on them, and away from sources of heat such as radiators or heat-generating electrical devices. Printable CD-R and CD-RW discs arent recommended, as the label side might be sticky and damage the unit. Do not stick papers or protective sheets on the discs and do not use any protective coating spray. Use a soft oil-based felt-tipped pen to write the information on the label side. Never use a ball-point or hard-tipped pen, as this may cause damage to the recorded side. Never use a stabilizer. Using commercially available CD stabilizers with this unit will damage the mechanisms and cause them to malfunction. Do not use CDs with an irregular shape (octagonal, heart shaped, business card size, etc.). CDs of this sort can damage the unit:
If you are in any doubt as to the care and handling of a CDR/
CD-RW disc, read the precautions supplied with the disc, or contact the disc manufacturer directly. 16 Cassette Tape Records Handling How to replace the stylus Replace the stylus 1. Use a screwdriver to push the stylus off then pull it out as the figures below:
2. Install the new stylus as figures below:
(Guide pins inside) 17 Troubleshooting If you experience any problems with the unit, please take a monent to look through this chart and see if you can solve the problem yourself before you call your dealer. No power Check the connection of AC wall outlet. No sound. Rising the volume level by turn the Power ON/OFF - VOLUME knob clockwise. Noisy sound:
The unit is too close to a TV set or similar appliances. Relocate the unit. Radio:
Can not listen to any station, or signal is too weak. Tune the station properly. The Function selector is in wrong position, turn it to Relocation the unit. RADIO position. Turntable:
Not playing or sound distortion The Function selector is in wrong position, turn it to PHONO position. Loosen the screw, and take out the stylus guard.
(The stylus guard is a white plastic cover that protects the stylus during transportation.) Select the correct playback speed. CD Player Not playing The Function selector is in wrong position, turn to CD position. Load the disc with the label side face up. If the disc is dirty, clean the surface of the disc. Try again wth another disc. Cassette Tape Player Not playing The tape has not insert completely. Insert the tape tightly until the Eject button is ejected. The Function selector is in wrong position, turn it to TAPE/AUX position. Bluetooth Not playing The Function selector is in wrong position, turn it to TAPE/AUX position. The external BT device had NOT paired to the unit The external BT device too far from the unit Sound is distorted or noisy Clean and demagnetize the heads. If the unit is halt or abnormal operation, unplug the power cord from the wall outlet and plug it again. Maintenance:
Always keep the turntable clean. If the surface of the unit gets dirty, wipe with a soft cloth or liquid soap. Be sure to remove any excess damage the surface of the of the unit to dry completely before using. unit. Allow the surface liquid completely. Do not use thinner, benzine or alcohol as use a diluted mild they may 18 Specifications Power Requirement...........................................................................................................................AC 120V~, 60Hz 20 W Power Consumption............................................................................................................................................. Audio:
Impedance of speakers: .............................................................................................................2 x 2W; 4Ohm Radio:
Frequency range (FM) Frequency range (AM)
................................................................................................................... 88MHz~108MHz
............................................................................................................. 530 kHz to 1710 kHz Cassette:
Track System Tape Speed Wow and Flutter Frequency Response Signal-to-Noise Ratio
..................................................................................................................................... 4 track, stereo
............................................................................................................................................. 4.8 cm/sec
................................................................................................................................. 0.15%(WRMS)
............................................................................................................................100-8,000Hz
......................................................................................................................................... 35dB Bluetooth:
Working range Turntable:
.......................................................................................................................................about 32 feet Motor Drive System Speed Wow and Flutter Cartrige Type Stylus
.................................................................................................................................................DC servo motor
.............................................................................................................................................. Belt Drive
........................................................................................................................... 33-1/3 rpm, 45 rpm, 78 rpm
................................................................................................................... less than 0.15% (WDT)
...................................................................................................................Ceramic Stereo Cartridge
...........................................................................................................................................................CSC-015 Design and specifications are subject to change without notice. Accessories:
1 x User's manual 1 x 45 rpm Adaptor 1 x AUX IN Cable For service assistance and product information, please call: 1-800-968-9853. Curtis International Ltd. 7045 BECKETT DRIVE, UNIT 15, MISSISSAUGA, ON, L5S 2A3 www.curtisint.com 18 PLATINE NOSTALGIA 6 EN 1 MODLE: SRCD838BT MODE DEMPLOI VEUILLEZ LIRE ATTENTIVEMENT AVANT LA MISE EN SERVICE CONSIGNES DE SCURIT IMPORTANTES ATTENTION RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR ATTENTION : AFIN DE RDUIRE LES RISQUES DE CHOC LECTRIQUE, NE PAS RETIRER L E COUVERCLE (OU LE CAPOT ARRIRE). NE CONTIENT AUCUNE PICE REMPLAABLE PAR L'UTILISATEUR. CONTACTEZ L E PERSONNEL QUALIFI POUR TOUTE OPRATION DE MAINTENANCE. ATTENTION :
CE LECTEUR DE VIDODISQUE NUMRIQUE UTILISE UN SYSTME LASER. POUR SASSURER DU BON USAGE DE CE PRODUIT, VEUILLEZ LIRE ATTENTIVEMENT CE MANUEL DUTILISATEUR ET LE CONSERVER POUR UNE UTILISATION ULTRIEURE. POUR LA MAINTENANCE DE LQUIPEMENT, VEUILLEZ CONTACTER UN CENTRE DE SERVICE AGRE-VOIR LA PROCDURE DE SERVICE. LUTILISATION DES COMMANDES, LES AJUSTEMENTS OU LEXCUTION DES PROCDURES AUTRES QUE CEUX/CELLES SPCIFI(E)S DANS LE PRSENT MANUEL PEUT ENTRANER DES EXPOSITIONS DANGEREURES AUX RADIATONS. POUR EMPCHER UNE EXPOSITION DIRECTE AU RAYONNEMENT LASER, NESSAYEZ PAS DOUVRIR LE COFFRET. UN RAYONNEMENT LASER VISIBLE PEUT SURVENIR LORSQUE LE COFFRET EST OUVERT. NE JAMAIS REGARDER DANS LE FAISCEAU. AVERTISSEMENT :
POUR RDUIRE LE RISQUE DINCENDIE OU DE CHOC LECTRIQUE, NE PAS EXPOSER CET APPAREIL LA PLUIE OU LHUMIDIT. AVERTISSEMENT :
POUR RDUIRE LE RISQUE DINCENDIE OU DE CHOC LECTRIQUE ET PARASITES, UTILISER UNIQUEMENT LES ACCESSOIRES RECOMMANDS. CONFORMIT LINDUSTRIE DU CANADA MOULEUX-3(B)/NMB-3(B) AVERTISSEMENT:
La prise secteur est utilise en tant que dispositif dconnect. le dispositif dconnect doit toujours tre en tat de marche. Lquipement est un appareil lectrique de classe II ou double isolation. Le symbole reprsentant un clair dans un triangle signifie que cet appareil comporte des composants non isols qui pourraient comporter une intensit suffisante pour causer des chocs lectriques si le botier est ouvert. Le point dexclamation dans un triangle attire votre attention sur des points importants de ce manuel concernant lutilisation ou lentretien de lappareil. DANGER Radiation de laser invisible et dangereuse lorsquil est ouvert et le verrouillage est en panne ou dsactiv. vitez toute exposition directe au faisceau. 2 DCLARATION DE LA FCC :
Cet quipement a t test et jug conforme aux limites tablies pour un dispositif numrique de classe B, conformment la partie 15 de la rglementation FCC. Ces limites ont ts mises en place pour offrir une protection raisonnable contre les interfrences dans un complexe rsidentiel. Cet quipement gnre et peut mettre des frquences radio et, sil nest pas install et utilis conformment aux instructions du mode demploi, peut causer des interfrences nuisibles aux communications radio. Mais il nexiste aucune garantie que des interfrences ne seront pas produites dans une installation particulire. Si cet quipement cre des interfrences pour la rception radio ou tlvisuelle, ce qui peut tre constat en lallumant et en lteignant, alors il vous est conseill dy remdier dune des manires suivantes :
Rorienter ou dplacer lantenne rceptrice. Augmenter la distance entre lquipement et le rcepteur. Connectez lquipement une prise ou un circuit diffrent de celui du rcepteur. Prenez conseil auprs du revendeur ou dun technicien radio/TV qualifi pour obtenir de laide. AVERTISSEMENT DE LA FCC :
Pour sassurer la conformit de lappareil, suivez les instructions de ce manuel et utilisez seulement des cbles blinds pour le raccordement dautres appareils. Les modifications non autorises par le fabricant pourraient annuler le droit de lutilisateur de faire fonctionner cet appareil. Il a t conu de manire ne pas ncessiter une mise la terre de scurit. 3 CONSIGNES DE SCURIT IMPORTANTES Avant dutiliser lappareil, veuillez vous assurer de lire attentivement les instructions. Veuillez remarquer que ce sont des prcautions gnrales et pourraient ne pas sappliquer votre appareil. Par exemple, cet appareil pourrait ne pas avoir la capacit dtre branch une antenne extrieure. 1) Lire ces instructions. Toutes les instructions concernant la scurit et le mode demploi devraient tre lues avant de faire fonctionner ce produit. 2) Conserver ces instructions. Les instructions concernant la scurit et le mode demploi devraient tre conserves pour rfrence future. 3) Tenir compte de tous les avertissements. Tous les avertissements sur le produit et dans le mode demploi devraient tre respects. 4) Suivre toutes les instructions. Toutes les instructions dutilisation devraient tre suivies. 5) Ne pas utiliser cet appareil prs de leau. Ne pas utiliser ce produit prs de leau et de lhumidit. Par exemple : prs dune baignoire, dun lavabo, dun vier de cuisine ou un bac lessive, dans un sous-sol humide, ou prs dune piscine. 6) Nettoyer seulement avec un chiffon sec. Dbrancher cet appareil avant de le nettoyer. Ne pas utiliser de nettoyant liquide ou en arosol. Utiliser un chiffon sec pour le nettoyer. 7) Ne pas bloquer les ouvertures de ventilation. Installer selon les instructions du fabricant. Les fentes et ouvertures dans le cabinet, larrire ou en dessous sont pour la ventilation afin de sassurer du fonctionnement continu de lappareil et pour lempcher de surchauffer. Ces ouvertures ne doivent pas tre bloques ou couvertes. Ces ouvertures ne doivent jamais tre bloques en plaant le produit sur un lit, divan, tapis ou autre surface similaire. Ce produit ne devrait jamais tre plac proximit dune source de chaleur ou dun radiateur. Ce produit ne devrait pas tre plac dans une installation assemble comme une bibliothque ou une tagre moins quil y ait une ventilation adquate ou que les instructions du fabricant soient respectes. 8) Ne pas installer prs dune source de chaleur telle quun radiateur, une cuisinire ou un autre appareil (y compris un amplificateur) qui produit de la chaleur. 9) Ne pas contourner le dispositif de scurit de la fiche polarit ou de mise la terre. Une fiche polarise possde deux lames dont lune est plus large que lautre. Une fiche de mise la terre possde deux lames et une troisime broche de mise la terre. La lame large ou la troisime broche est l pour votre scurit. Si la fiche ne sadapte pas votre prise, consulter un lectricien pour le remplacement de la prise dsute. 10) Protger le cordon dalimentation afin quil ne soit pas pitin ou pinc, surtout au niveau de la fiche, de la prise et lendroit o il sort de lappareil. 11) Utiliser seulement des accessoires recommands par le fabricant. 12) Utilisez uniquement le chariot, trpied, support ou table spcifis par le fabricant, ou vendus avec lappareil. Lorsquun chariot est utilis, faire attention lors du dplacement de la combinaison chariot/appareil afin dviter toute blessure lors dun basculement. Une combinaison de chariot et dappareil devrait tre dplac avec soin. Un arrt brusque, force excessive et surfaces irrgulires peuvent faire basculer la combinaison de chariot et dappareil. 13) Dbrancher cet appareil durant les orages ou lorsquil est inutilis pendant une longue priode de temps. Pour protger votre produit des orages ou lorsquil nest pas utilis pendant une longue 4 priode de temps, le dbrancher de la prise murale et dbrancher lantenne ou le systme de cble. Cela prviendra tout dommage au produit caus par les clairs et les surtensions. 14) Rfrer tout entretien des techniciens expriments. Une rparation est ncessaire lorsque lappareil a t endommag de quelque faon, tel que cordon dalimentation ou fiche endommag, liquide renvers ou objets tombs dans lappareil, appareil expos la pluie ou lhumidit, appareil ne fonctionne pas normalement, ou sil a t chapp. 15) Source dalimentation Ce produit devrait tre aliment seulement partir du type de source dalimentation spcifi sur ltiquette. Si vous ntes pas certain de la source dalimentation, veuillez contacter le vendeur ou la compagnie dlectricit locale. Pour les produits conus pour fonctionner avec des piles ou dautres sources, se rfrer au mode demploi. 16) Lignes lectriques Une antenne extrieure ne doit pas tre situe proximit de lignes lectriques ariennes ou autres circuits lectriques ou dalimentation, ou si elle peut tomber sur ces lignes ou circuits lectriques. Lors de linstallation de systme dantenne extrieure, viter de toucher ces lignes ou circuits car leur contact peut tre fatal. 17) Surcharge Ne pas surcharger les prises murales et les rallonges, car cela pourrait entraner un risque dincendie ou de choc lectrique. 18) Insertion dobjet ou de liquide Ne jamais insrer dobjet dans le produit travers les ouvertures car il pourrait toucher des points de tensions dangereux ou faire court-circuiter des pices, ce qui pourrait causer un incendie ou choc lectrique. Ne jamais verser ou pulvriser aucun type de liquide sur le produit. 19) Mise la terre dantenne extrieure Si une antenne extrieure est branche au produit, veuillez vous assurer que le systme dantenne est mis la terre afin de fournir une protection contre les surtensions et les charges statiques. Larticle 810 du code lectrique national (National Electrical Code), ANSI / NFPA 70, fournit des informations relatives la mise la terre adquate du mt et sa structure, la mise la terre du fil conducteur un produit de dcharge dantenne, la taille des conducteurs de mise la terre, lemplacement des produits de dcharge dantenne la connexion aux lectrodes de mise la terre et les exigences pour les lectrodes de mise la terre. PINCE DE MASSE QUIPEMENT DE SERVICE DLECTRICIT DANTENN FIL E DCHARGE DANTENNE
(NEC SECTION 810-20) CONDUCTEURS DE MASSE
(NEC SECTION 810-21) CONDUCTEURS DE MASSE (NEC SECTION 810-21) SYSTME DLECTRODE DE MASSE DE SERVICE DLECTRICIT (NEC ART 250, PARTH) 5 20) Entretien Ne pas essayer deffectuer vous-mme lentretien de ce produit puisque louverture ou le retrait des couvercles pourrait vous exposer des tensions dangereuses et autres risques. Rfrer tout entretien des techniciens expriments. 21) Pices de remplacement Lorsque des pices de remplacement sont requises, sassurer que le technicien utilise des pices de remplacement spcifies par le fabricant ou que celles-ci possdent les mmes caractristiques que la pice originale. Les substitutions non autorises pourraient causer des incendies, chocs lectriques ou autres risques. 22) Vrification de scurit Lorsque les rparations sont termines, veuillez demander au technicien deffectuer des contrles de scurit pour dterminer si le produit est en bon tat de fonctionnement. 23) Dommage ncessitant une rparation Dbrancher le produit de la prise murale et confier la rparation un technicien qualifi si une des conditions suivantes est rencontre :
a. Lorsque le cordon dalimentation ou la fiche est endommag. b. Si du liquide a t renvers ou des objets sont tombs sur le produit. c. Si le produit a t expos la pluie ou de leau. d. Si le produit ne fonctionne pas normalement en suivant le mode demploi. Ajuster seulement les contrles viss par le mode demploi, comme lajustement des autres contrles pourrait causer des dommages et occasionnerait un effort supplmentaire de la part du technicien pour restaurer le produit son tat de fonctionnement. e. Si le produit a t chapp ou si le cabinet a t endommag. f. Lorsque le rendement de lappareil diminue de faon notable. 24) Remarque linstallateur du systme CATV Ce rappel est destin attirer lattention de linstallateur du systme CATV sur larticle 820-
40 du NEC qui fournit des directives pour la mise la terre adquate et, en particulier, spcifie que le cble de mise la terre doit tre reli au systme de la mise la terre du btiment, aussi prs que possible du point dentre du cble. REMARQUE : Rfrer tout entretien des techniciens expriments. Une rparation est ncessaire lorsque lappareil a t endommag de quelque faon telle que : le cordon dalimentation ou la fiche a t endommage, du liquide a t renvers dans lappareil, lappareil a t expos la pluie ou lhumidit, lappareil a t chapp ou lappareil ne fonctionne pas normalement. 6 Emplacement des composants Platine Avant lutilisation, veuillez enlever la protection de la tte de lecture (enveloppe blanche en plastique) en le tirant. Platine Fixation de la vis par vis pour le transport. Avant la premire utilisation, desserrez compltement la vis en la tournant dans le sens horaire. Lorsque vous transportez de nouveau lappareil, serrez la vis dans le sens antihoraire afin de scuriser la platine. Levier Support des bras de lecture Slecteur de vitesses Bras de lecture 7 Emplacement des composants Vue de ct Vue de face VOLUME M I N O N. OF F MAX AUX IN Cassette Touche djection Haut-parleurs Slecteur de fonctions Bouton de syntonisation Bascule cadran de la radio Bouton MARCHE/ARRT-V0lume Bouton OVRIR/FERMER Prise AUX IN Bouton arrter Bouton LECTURE/PAUSE Bouton RPTER Affichage DEL pour CD Plateau porte-disques Bouton PROGRAMME Boutons B.SKIP et F.SKIP
(Sauter en avant et sauter en arrire) Commutateur de BANDES AM/FM Sortie CASQUE 8 Emplacement des composants Vue arrire Antenne FM Prises LINE OUT
(sortie de ligne) Cble dalimentation CA Ouverture/fermeture du couvercle de la platine Pour ouvrir :
1. Soulevez le couvercle de la platine. 2. Tirez les bras vers lavant pour le fermer comme lindique la figure gauche. Pour fermer :
1. Soulevez le couvercle. 2. Poussez les bras vers larrire pour dsengager le verrouillage. 3. Fermez le couvercle. 9 coute dun disque Vis de transport VOLUME M I N O N. OF F MAX AUX IN Avant de procder au transport, desserrez compltement la vis en la tournant dans le sens horaire. Enlevez la protection de la tte de lecture (enveloppe blanche en plastique) 1. Pour allumer lunit, tournez le bouton MARCHE/ARRT-VOLUME dans le sens horaire jusqu entendre un clic . 2. Basculez le slecteur de fonctions la position PHONO. 3. Ouvrez le couvercle. 4. Slectionnez la vitesse. 5. Placez le disque sur la platine. Si vous souhaitez lire un disque de petite taille 45 tr/
min, placez ladaptateur rond fourni sur laxe central avant de poser le disque. tape 1 tape 2 Adaptateur 45 TR/M 10 6. Dverrouillez le clip pour relcher le bras de lecture tel quillustr sur la figure ci- dessous. clip 7. Soulevez le levier clip pour lever le bras de lecture tel quillustr sur la figure ci-
dessous. 10. Tournez le bouton MARCHE/ARRT-
VOLUME pour ajuster le volume. levier 8. Placez le bras de lecture sur la face suprieure du disque. La platine commencera tourner. 11. la fin de lcoute, tez le bras de lecture du reste et verrouillez en suivant les procdures prcdentes. Pour teindre lunit, tournez le bouton MARCHE/ARRT-
VOLUME dans le sens antihoraire jusqu entendre un clic . 9. Placez le bras de lecture sur le point dsir du disque en basculant le levier vers le bas comme le montre la figure ci-
dessous. levier 11 coute dun CD VOLUME M I N O N. OF F MAX AUX IN Lecture de CD :
1. Pour allumer lunit, tournez le bouton MARCHE/ARRT-VOLUME dans le sens horaire jusqu entendre un clic . 2. Basculez le slecteur de fonctions la position CD. 3. Appuyez sur le bouton OUVRIR/FERMER pour ouvrir le plateau porte disques. 4. Placez un disque sur le plateau, la face imprime regardant vers le haut.
* Ne placez jamais plus dun disque sur le plateau.
* Le disque doit tre plac au centre du plateau porte-disques. Si le disque nest pas correctement charg, il peut savrer impossible de rouvrir le plateau une fois quil se soit ferm. 12 5. Appuyez sur le bouton OUVRIR/FERMER pour fermer le plateau porte disques. Quelques secondes aprs, le nombe total de pistes apparatra sur laffichage DEL et la lecture dbutera automatiquement. 6. Tournez le bouton MARCHE/ARRT-VOLUME pour ajuster le niveau de volume dsir. 7. Pendant la lecture
~ Appuyez sur le bouton LIRE/PAUSE pour mettre en pause, appuyez de nouveau pour reprendre la lecture normale
~ Appuyez sur le bouton B.SKIP ou F.SKIP de manire rpte pour passer au titre suivant.
~ Appuyez sur le bouton B.SKIP ou F.SKIP et maintenez le enfonc, pour rechercher rapidement la section souhaite.
~ Pour arrter, appuyez sur le bouton STOP (ARRT). 8. la fin de lcoute Pour teindre lunit, tournez le bouton MARCHE/ARRT-VOLUME dans le sens antihoraire jusqu entendre un clic . coute dun CD Rpter la lecture :
Pendant la lecture 1). Appuyez une fois sur le bouton RPTER, lindicateur de rptition sallumera et clignotera. La piste actuelle jouera de faon rpte jusqu ce que le bouton STOP soit press. 3). Pour annuler la fonction de rptition au cours de la lecture, appuyez sur le bouton RPTER de faon rpte jusqu ce que lindicateur de rptition steigne. 2). Appuyez deux fois sur le bouton RPTER, lindicateur de rptition sallumera et clignotera. Toutes les pistes du CD actuel joueront de faon rpte jusqu ce que le bouton STOP soit press. 13 Lecture programme :
Jusqu 20 pistes peuvent tre programmes la lecture comme suit :
1. En mode CD STOP (ARRTER CD), appuyez sur le bouton PROGRAMME. 01 apparatra sur laffichage DEL et clignotera. 2. Slectionnez la premire piste programmer en appuyant sur les boutons B.SKIP ou F.SKIP. 3. Appuyez de nouveau sur le bouton PROGRAMME pour enregistrer la piste slectionne dans 4. Rptez les tapes 2 et 3 jusqu ce que toutes les diffrentes pistes soient enregistres dans la mmoire. la mmoire. 5. Appuyez sur le bouton LIRE/PAUSE pour dmarrer la lecture. 6. Pour arrter et annuler la lecture programme, appuyez sur le bouton STOP. coute de la radio VOLUME M I N O N. OFF MAX AUX IN 1. Pour allumer lunit, tournez le bouton MARCHE/ARRT-VOLUME dans le sens horaire jusqu entendre un clic . 3. Glissez le commutateur de bandes AM/
FM sur AM ou FM selon votre choix. 2. Basculez le slecteur de fonctions la position RADIO. 4. Tournez le bouton de syntonisation pour capter la station radio dsire. 5. Tournez le bouton MARCHE/ARRT-
VOLUME pour ajuster le niveau de volume. 14 6. la fin de lcoute, teignez lunit en tournant le bouton MARCHE/ARRT-VOLUME dans le sens antihoraire jusqu entendre un clic . Antennes :
AM- Cette unit dispose dune antenne tige de ferrite intgre, laquelle assure une rception adquate dans la plupart des zones. Si le signal est faible, tournez lunit pour avoir une meilleure rception. FM- Le fil dantenne FM est destin la rception du signal FM. Si le signal est faible, droulez le cble et allongez-le, ou alors repositionnez le fil pour amliorer la rception radio. BLUETOOTH 15 coute dune bande de cassette VOLUME M I N O N. OFF MAX AUX IN 1. Pour allumer lunit, tournez le bouton MARCHE/ARRT-VOLUME dans le sens horaire jusqu entendre un clic . 2. Basculez le slecteur de fonctions la position TAPE/AUX . 3. Insrez une bande de cassette pr-
enregistre dans le compartiment rserv la cassette jusqu ce que le bouton Eject soit ject. La lecture dmarrera automatiquement. 4. Tournez le bouton MARCHE/ARRT-
VOLUME pour ajuster le niveau de volume. 16 5. Avance rapide 6. Arrter la lecture et jecter la cassette la fin de lcoute, appuyez sur le bouton jecter pour arrter la lecture et retirer la cassette. Pour teindre lunit, tournez le bouton MARCHE/ARRT-VOLUME dans le sens antihoraire jusqu entendre un clic . Pour effectuer une avance rapide jusquau point dsir, appuyez de moiti sur le bouton jecter. Lorsque vous avez termin, appuyez de nouveau sur le bouton pour reprendre la lecture. Remarque : la fin de lenroulement, noubliez pas dappuyer sur le bouton jecter pour arrter lenroulement et retirer la cassette. Le cas contraire, lunit restera en mode enroulement. Autres connexions AUX IN :
1. Permet de connecter un appareil audio externe lunit travers un cble de liaison audio avec des mini-jacks stro 3,5
~ Connectez une extrmit au tlphone ; prise Line Out ou AUX Out du priphrique audio externe.
~ Connectez lautre extrmit la prise AUX IN se trouvant lavant de lunit. 2. Pour allumer lunit, tournez le bouton MARCHE/ARRT - VOLUME dans le sens horaire mm de la manire suivante
:
jusqu entendre un clic . ....................................... Tlphone portable Connectez aux tlphones ;
AUX Out ; prise Line Out des priphriques audio (tel que lecteur MP3, portable, iPod/
iPad, etc.)
......................................... VOLUME M I N O N. OFF MAX AUX IN la prise AUX IN de lunit 17 3. Basculez le slecteur de fonctions la position TAPE/AUX . 4. Joue la musique sur le priphrique externe connect, comme dhabitude. 5. la fin de lcoute, teignez lunit en tournant le bouton MARCHE/ARRT - VOLUME dans le sens antihoraire jusqu entendre un clic . Remarques :
Rassurez-vous que le niveau sonore de sortie du priphrique audio externe connect est lev. Le cas contraire, le son sera faible. LINE OUT :
1. Permet de connecter un appareil audio externe travers un cble de liaison audio avec des fiches RCA (cble non inclus) de la manire suivante :
~ Connectez une extrmit aux prises Line IN ou AUX In de lamplificateur audio externe.
~ Connectez lautre extrmit aux prises LINE OUT se trouvant larrire de lunit. 2. Pour allumer lunit, tournez le bouton MARCHE/ARRT - VOLUME dans le sens horaire jusqu entendre un clic
.
(Cble de liaison non inclus) Aux prises Line IN ou AUX In de lamplificateur audio externe 3. Joue la musique/radio suivant les procdures prcdentes. Un son provenant du systme de lamplificateur audio externe se fera entendre. Ajustez le niveau sonore grce aux commandes du volume de lamplificateur externe connect.
(Si vous ne souhaitez pas entendre le son provenant de cette unit, alors tournez le bouton MARCHE/ARRT - VOLUME la position infrieure). 4. la fin de lcoute, teignez lunit en tournant le bouton MARCHE/ARRT - VOLUME dans le sens antihoraire jusqu entendre un clic . Prise Phones :
Pour une coute prive, connectez un casque / couteur (non inclus) la prise PHONE lavant de lunit. Les haut-
parleurs sont dconnects lorsque le casque / couteur est insr dans la prise. 18 propos des disques Disques pouvant tre lus laide de cet appareil :
CD audio standard portant le logo CD-DA sur ltiquette. Disques CD-R et CD-RW correctement gravs. Placer toujours le disque sur le plateau disque avec ltiquette vers le haut. Pour retirer un disque de son botier de rangement, appuyez sur le centre du botier et
(Les disques compacts ne peuvent tre lus ou gravs que dun seul ct). soulevez le disque en le tenant soigneusement par les bords. Comment retirer le disque Comment tenir le disque Si le disque devient sale, essuyez sa surface dun mouvement allant du centre vers le bord extrieur avec un chiffon doux et sec. Pour nettoyer les disques, nutilisez jamais de produits chimiques comme des vaporisateurs pour disques vinyle, des vaporisateurs ou fluides antistatiques, du benzne ou des diluants. De tels produits chimiques causeront des dommages irrparables la surface en plastique du disque. Les disques doivent tre remis dans leurs botiers aprs leur utilisation pour viter la poussire et les rayures qui pourraient causer le sautillement du capteur laser. Nexposez pas les disques la lumire directe du soleil ou une humidit et des tempratures leves pendant de longues priodes. Une exposition prolonge des tempratures leves peut causer la dformation du disque. Ne faites jouer aucun disque gondol, dform ou endommag. Faire jouer de tels disques peut causer des dommages irrparables aux mcanismes de lecture. Les disques CD-R et CD-RW sont plus sensibles aux effets de la chaleur et des rayons ultraviolets que les CD ordinaires. Il est important quils ne soient pas stocks dans un endroit expos la lumire directe du soleil et quils soient loin de toute source de chaleur comme les radiateurs ou les appareils lectriques produisant de la chaleur. Les CD-R et CD-RW imprimables ne sont pas recommands, car le ct de ltiquette pourrait Ne collez pas de papiers ou de feuilles protectrices sur les disques et nutilisez aucun enduit tre collant et endommager lappareil. protecteur en vaporisateur. Utilisez un crayon-feutre doux base dhuile pour crire les informations sur le ct de ltiquette. Nutilisez jamais un stylo-bille ou stylo pointe dure, car cela peut endommager le ct grav. Nutilisez jamais un stabilisateur. Lutilisation de stabilisateurs de CD offerts sur le march avec cet appareil endommagera les mcanismes et causera leur dfaillance. Nutilisez pas de CD ayant une forme irrgulire (octogonale, en forme de cur, taille de la carte daffaires, etc.). Des CD de ce genre peuvent endommager lappareil. Si vous avez des doutes relativement lentretien et la manipulation dun disque CDR/CD-RW, lisez les consignes fournies avec le disque, ou contactez directement le fabricant de disques. 19 Slection de la bande Les bandes de mtal et chrome (cobalt) ont des trous didentification. Bande de cassette Manipulation des bandes Utilisez vos doigts ou un crayon pour faire tourner le moyeu de la cassette et ainsi bien tendre la bande. salet. vitez de toucher la bande. Les empreintes laisses par les doigts attirent la poussire et la vitez de laisser tomber les cassettes ou de les soumettre des chocs excessifs. Nutilisez pas les bandes C-120, car elles sont physiquement faibles et pourraient senchevtrer dans le mcanisme de dfilement. Ne rangez pas de cassettes dans les endroits suivants :
Sur le dessus de radiateurs, les endroits exposs la lumire directe du soleil, ou dans tout autre endroit soumis des tempratures leves. Prs de haut-parleurs, sur les tlviseurs ou amplificateurs ou des endroits o ils seraient exposs des champs magntiques puissants. L o lhumidit est leve et dans des endroits sales et poussireux. Entretien de la tte La tte et le parcours de dfilement de la bande doivent tre nettoys et dmagntiss priodiquement. Veuillez utiliser une cassette de nettoyage et de dmagntisation de tte de lecture de cassette. Pour plus dinformations sur lutilisation approprie dun article, veuillez lire le mode demploi de chaque article. Manipulation des disques Ne touchez pas aux rainures du disque. Manipulez les disques vinyle uniquement par les bords ou ltiquette. Assurez-vous que vos mains soient propres. Les huiles produites par la peau des mains peuvent laisser un rsidu sur la surface du disque qui dtriora progressivement la qualit de votre enregistrement sur le disque. 20 Conservez vos disques vinyle loin de la poussire. Conservez-les dans un endroit frais et sec. Pour viter la poussire et des rayures, gardez les disques vinyle dans leurs enveloppes et leurs pochettes lorsquils ne sont pas utiliss. Rangez les disques vinyle en position debout sur leurs bords. Les disques vinyle rangs horizontalement vont ventuellement plier et se dformer. Nexposez pas les disques vinyle la lumire directe du soleil ou une humidit et des tempratures leves. Une exposition prolonge des tempratures leves peut causer la dformation du disque vinyle. Ne rangez pas vos disques vinyle dans le coffre de votre voiture. La temprature dans un coffre ferm peut ruiner votre collection. Rangez les disques vinyle dans un endroit soumis une temprature stable et une faible Si le disque vinyle devient sale, essuyez doucement la surface dans un mouvement circulaire laide dun chiffon doux antistatique. humidit. Comment remplacer le stylet Remplacer le stylet 1. Utilisez un tournevis pour pousser le stylet tel que le montre les figures suivantes :
2. Installez le nouveau stylet selon les figures suivantes :
Tiges de guidage
(intrieure) 21 En cas de problme avec lappareil, veuillez parcourir cette reprsentation graphique et voir si vous pouvez rsoudre le problme vous-mme avant de contacter votre concessionnaire. Dpannage Pas dalimentation Vrifiez la connexion de la prise de courant murale. Pas de son Augmentez le volume en tournant le bouton MARCHE/ARRT - VOLUME dans le sens horaire Changez la position de lquipement. Son bruyant :
Lunit est trs proche dun tlviseur ou dappareils similaires. Radio :
Impossible dcouter une station de radio, ou signal trop faible Recherchez la station de manire correcte. Le slecteur de fonctions est mal positionn, mettez-le en position RADIO. Changez la position de lqu ipement. Platine :
Ne joue pas ou distorsion du son Le slecteur de fonctions est mal positionn, mettez-le en position PHONE. Desserrez la vis et retirez la protection de la tte de lecture.
(La protection de la tte de lecture est une enveloppe blanche en plastique qui protge le stylet pendant le transport. Slectionnez la vitesse de lecture approprie. Lecteur de CD Ne joue pas Le slecteur de fonctions est mal positionn, mettez-le en position CD. Chargez le disque de manire ce que la face imprime regarde vers le haut. Si le disque est sale, nettoyez la surface du disque. Essayez un autre disque. Lecteur de bande de cassette Ne joue pas La cassette na pas t entirement insre. Insrez correctement la cassette jusqu ce que le bouton jecter soit ject. Le slecteur de fonctions est mal positionn, mettez-le en position TAPE/AUX . Son bruyant ou distordu Nettoyez et dmagntisez les ttes. Si lunit fonctionne de manire anormale, dbranchez le cble dalimentation de la prise de courant murale et rebranchez-le. 22 Maintenance :
Veuillez conserver la platine toujours propre. Si la surface de lunit se salit, nettoyez-la laide dun tissu doux ou utilisez une solution savonneuse douce dilue. Rassurez-vous de retirer compltement tout excs de liquide. Nutilisez pas de solvants comme le diluant, le benzne ou lalcool car ils peuvent endommager la surface de lunit. Laissez scher la surface de lunit avant de lutiliser. Caractristiques Gnrales Alimentation ....................................................................................................120 V en CA~, 60 Hz Consommation ........................................................................................................................ 20 W Audio :
Impdance des haut-parleurs : ...............................................................................2 x 2 W; 4 Ohms Radio :
Plage de frquence (FM) .....................................................................................88 MHz~108 MHz Plage de frquence (AM) ................................................................................. 530 kHz 1710 kHz Cassette :
Piste Systme.......................................................................................................................4 streo Vitesse de bande ............................................................................................................. 4,8 cm/sec Pleurage et scintillement .........................................................................................0,15 % (WRMS) Rponse en frquence ................................................................................................ 100-8 000 Hz Rapport signal/bruit ................................................................................................................ 35 dB Platine :
Moteur ....................................................................................................................Servomoteur CC Systme dentranement..........................................................................Entranement par courroie Vitesse ..........................................................................................33-1/3 tr/min, 45 tr/min, 78 tr/min Pleurage et scintillement ........................................................................ infrieurs 0,15 % (WDT) Type de cartouche .......................................................................... Cartouche stro en cramique Stylet...................................................................................................................................CSC-015 Le modle et les caractristiques sont sujets des modifications sans pravis. Accessoires :
1 x Manuel dutilisateur 1 x Adaptateur 45 tr/min 1 x Cble AUX IN Pour obtenir assistance et information appelez: 1-800-968-9853. Curtis International Ltd. 7045 BECKETT DRIVE, UNIT 15, MISSISSAUGA, ON, L5S 2A3 www.curtisint.com 23
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2018-11-02 | 2402 ~ 2480 | DSS - Part 15 Spread Spectrum Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2018-11-02
|
||||
1 | Applicant's complete, legal business name |
Shenzhen Junlan Electronic Ltd
|
||||
1 | FCC Registration Number (FRN) |
0021880893
|
||||
1 | Physical Address |
No.277 PingKui Road, Shijing Community
|
||||
1 |
Shenzhen, N/A
|
|||||
1 |
China
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
c******@micomlabs.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
OKU
|
||||
1 | Equipment Product Code |
SRCD838BT
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
p****** x****
|
||||
1 | Title |
safety engineer
|
||||
1 | Telephone Number |
0755-********
|
||||
1 | Fax Number |
0755-********
|
||||
1 |
x******@jump-lan.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Shenzhen NTEK Testing Technology Co., Ltd.
|
||||
1 | Name |
J****** C****
|
||||
1 | Physical Address |
1/F, Building E, Fenda Science Park
|
||||
1 |
Shenzhen, Guangdong, 518126
|
|||||
1 |
China
|
|||||
1 | Telephone Number |
(86)-********
|
||||
1 |
J******@ntek.org.cn
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DSS - Part 15 Spread Spectrum Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Nostalgia 6 in 1 Turntable Radio | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output power listed is conducted power. The antenna used with this transmitter must be installed to provide a minimum separation distance of at least 20 cm from all persons. End-users must be provided with operating procedures for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Shenzhen NTEK Testing Technology Co., Ltd.
|
||||
1 | Name |
A******** L****
|
||||
1 | Telephone Number |
+86-7********
|
||||
1 |
c******@ntek.org.cn
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | 20 | 2402.00000000 | 2480.00000000 | 0.0038000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC