FCC ID: 2BDPQ-LSFD002 Locate It Device

Locate It Device User Manual Locate It Device User Manual Index 2 01 Getting Started 02 Add Your Locate It Device 03 Locate Your Locate It Device 04 Notifications 05 When Your Locate It Device Is Lost 06 Lookup Serial Number 07 Resetting Locate It Device 08 Extras 09 The Fine Print 10 About Apple Find My Locate It Device User Manual 01 Getting Started 01.1 Power On / Off:

3 Place the CR2032 battery (positive side up, i.e. text facing up) into the battery case in the back of Locate It Device, it is automatically turned on. Or press the Locate It Devices Function Button once to turn it on if the battery is already in the battery case. It should beep once to indicate that it is powered on. To power off, press and hold the same button until two confirmation beeps sound, then release the button, two short beeps will sound to indicate that it is powered off. 01.2 Check For Updates:

To use the Find My app to locate this item, the latest version of iOS, iPadOS or macOS is recommended. The Find Items app on Apple Watch requires the latest version of watchOS. Locate It Device User Manual 4 02 Add Your Locate It Device 02.1 Start The APP Open Find My app on your supported iPhone or iPad. 02.2 Connect Your Locate It Device Press the function button once to power on your Locate It Device. Tap+, then Add Other Item. Once your Locate It Device is located, tap Connect. Enter a name and choose an emoji for your Locate It Device and tap Continue. Find My will ask for confirmation to add your Locate It Device to your Apple ID, tap Agree. Tap Finish and your Locate It Device will be set up and ready to be used. Locate It Device User Manual 5 03 Locate Your Locate It Device 03.1 Find Locate It Device When Its Nearby:

Open Find My app and select the Item tab or open the Find Items app on your Apple Watch. Tap on your Locate It Device from the list. Tap Play Sound to make your Locate It Device beep. Tap Stop Sound to stop the beeps once you find. 03.2 Find Locate It Devices Location:

Open Find My app and select the Items tab or open the Find Items app on your Apple Watch. Tap on your Locate It Device from the list. Your Locate It Devices location will appear on the Map with a time stamp of when the Items was located. To navigate to the Locate It Devices location, tap Directions to open Apple Maps. Locate It Device User Manual 04 Notifications 6 04.1 Enabling Notify When Left Behind:

Open Find My app and select the Items tab or open the Find Items app on your Apple Watch. Tap on your Locate It Device from the list. Under Notifications enable the Notify When Left Behind toggle. You will receive a notification when you leave your Locate It Device behind and its no longer in range of your device. 04.2 Enabling Notify When Found:

When your Locate It Device has been put into Lost Mode, under Notifications, you can enable the Notify When Found toggle. When your Locate It Device is seen by another Find My network device, you will receive a notification of its location. Note: Notify When Found can also be activated when your Locate It Device is out of range. Locate It Device User Manual 7 05 When Your Locate It Device Is Lost 05.1 Enabling Lost Mode:

Open Find My app and select the Items tab or open the Find Items app on your Apple Watch. Tap on your Locate It Device from the list. Under Lost Mode tap Enable. A screen detailing Lost Mode will pop up, tap Continue. Enter Your phone number or email address and tap Next. You may enter a message that will be shared with the person that finds your Item. Tap Activate to enable Lost Mode. Note: When Lost Mode is enabled, Notify When Found is automatically enabled. Note: When Lost Mode is enabled, your Locate It Device is locked and cannot be paired to a new device. Locate It Device User Manual 8 06 Lookup Serial Number 06.1 Search The Locate It Device:

Open Find My app. Select Items, swipe up, and select Identify Found Item. Select the Locate It Device and select Continue. 06.2 Follow Instructions For Lookup Serial Number:

Locate the button in the back of the Locate It Device. Press and hold the button for six seconds. Three beeps will sound while the button is depressed. Release the button. Two confirmation beeps will sound. In the Find My app, Select Continue On Website, you will see the Serial Number information. Locate It Device User Manual 9 07 Resetting Locate It Device 07.1 Remove The Locate It Device From Find My app:

Open Find My app and select the Items tab. Tap on your Locate It Device from the list. Please ensure Lost Mode is disabled. Scroll to the bottom of the screen and tap Remove Item. A summary will open, tap Remove to confirm. 07.2 Factory Reset Your Locate It Device:

Locate the button in the back of the Locate It Device. After successfully removing the Locate It Device from Find My app, press and hold the Locate It Devices Function Button until four or more confirmation beeps sound, then release the button, three short beeps will sound to indicate that it is factory reset. The Locate It Device is now ready to be paired to a new Apple ID. Locate It Device User Manual 08 Extras 10 08.1 Replace The Battery:

Open the battery cover in the back of your Locate It Device. Replace the battery with a new CR2032 battery placing it positive side up (text facing up). Carefully close the battery cover in the back of your Locate It Device. 08.2 Unwanted Tracking If any Find My network accessory separated from its owner is seen moving with you over time, you'll be notified in one of the two ways:

1. lf you have an iPhone or iPad, Find My will send a notification to your Apple device. This feature is available on iOS or iPadOS 14.5 or later. 2. lf you don't have an iOS device, a Find My network accessory that isn't with its owner for a period of time will emit a sound when it's moved. These features were created specifically to discourage people from trying to track you without your knowledge. Locate It Device User Manual 09 The Fine Print 11 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or Tv interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes not expressly approved by the party responsible for compliance could void the user's authority to operate this device. The device has been evaluated to meet general RF exposure requirement, The device can be used in portable exposure condition without restriction. Federal Communication Commission (FCC) Radiation Exposure Statement Power is so low that no RF exposure calculation is needed. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Locate It Device User Manual 12 10 About Apple Find My The Apple Find My network provides an easy, secure way to locate compatible personal items on a map using the Find My app on your iPhone, iPad, or Mac. Simply pair your compatible product with the Apple Find My app to view it right alongside your Apple devices. If your item ever goes missing, you can put it in Lost Mode to display a message and contact information to anyone who might find it. The Find My network is encrypted and anonymous, so no one else, not even Apple or the maker of your personal item, can view its location. Use of the Works with Apple badge means that a product has been designed to work specically with the technology identified in the badge and has been certified by the product manufacturer to meet Apple Find My network product specifications and requirements. Apple is not responsible for the operation of this device or use of this product or its compliance with safety and regulatory standards. Apple, Apple Find My, Apple Watch, Find My, iPhone, iPad, iPadOS, Mac, macOS and watchOS are trademarks of Apple Inc. IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license. FCC Warning:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

80 90 1(

ilsertienl

.) lint 0 40 60 60 7 bisilivvcrereedieer 10 20 3 uli oli!

INT] FT) IVTD] TNT) EULA) TCUY) CUP p EERE PUTT EET) OL 02 O Ov 0S 09 02 08 06 QD} OF 0

Shenzhen Leshan Technology Co., Ltd Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 11/28/2023 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2BDPQ-LSFD002

[Shenzhen Leshan Technology Co., Ltd] certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signed:

Printed name: james_xu Title: general manager Company Name: Shenzhen Leshan Technology Co., Ltd. Rev 1/26/2023 Shenzhen Leshan Technology Co., Ltd. Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 11/28/2023 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2BDPQ-LSFD002

[Shenzhen Leshan Technology Co., Ltd] certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List(as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely, Signed:

Printed name: james_xu Title: general manager Company Name: Shenzhen Leshan Technology Co., Ltd. Rev 1/26/2023

Request for Confidentiality:

MUST BE ON COMPANY LETTERHEAD AND SIGNED BY OFFICIAL OF APPLICANT COMPANY 2023-11-28 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2BDPQ-LSFD002 Product Name: Locate It Device Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

Schematics Long-term confidential Block diagram Long-term confidential Operation description Long-term confidential These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors. Signature:

Name Position Company Name Address Tel Fax Email james_xu general manager Shenzhen Leshan Technology Co., Ltd Room 207, Building 1, Xinfu Material Market, No. 386 Chuangye Second Road, Xinan Street, Baoan District, Shenzhen 00860755-2330713 00860755-2330713 sales2@szleshan.com

Differences Description We Shenzhen Leshan Technology Co., Ltd state:

Product name: Locate It Device Model: LSFD002, LSFD003, LSFD004, LSFD005, LSFD006, LSFD007, LSFD008, LSFD009, LSFD010 All models the function, software and electric circuit are the same, except the model name difference. Signature:

Name Position Company Name Address Tel Fax Email james_xu general manager Shenzhen Leshan Technology Co., Ltd Room 207, Building 1, Xinfu Material Market, No. 386 Chuangye Second Road, Xinan Street, Baoan District, Shenzhen 00860755-2330713 00860755-2330713 sales2@szleshan.com

Shenzhen Leshan Technology Co., Ltd 2023-11-28 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Director of Certification Authority to Act as Agent On our behalf, I appoint Shenzhen Alpha Product Testing Co., Ltd. Address: Building i, No.2, Lixin Road, Fuyong Street, Baoan District, 518103, Shenzhen, Guangdong, China

(Name: Shenzhen Alpha Product Testing Co., Ltd. Person: Mark Zhu and address: Building i, No.2, Lixin Road, Fuyong Street, Baoan District, 518103, Shenzhen, Guangdong, China). to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, as specified by TMICO still resides with Shenzhen Leshan Technology Co., Ltd Address: Room 207, Building 1, Xinfu Material Market, No. 386 Chuangye Second Road, Xinan Street, Baoan District, Shenzhen (applicant name and address). Signature:

Name Position Company Name Address Tel Fax Email james_xu general manager Shenzhen Leshan Technology Co., Ltd Room 207, Building 1, Xinfu Material Market, No. 386 Chuangye Second Road, Xinan Street, Baoan District, Shenzhen 00860755-2330713 00860755-2330713 sales2@szleshan.com

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6962309.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Shenzhen Leshan Technology Co., Ltd U.S. Agent Designation for Service of Process -

Certification Attestation Letter 11/28/2023 ATTN.: Reviewing Engineer FCC ID: 2BDPQ-LSFD002 FRN: 0034520767 Per section 2.911(d)(7) of the FCC rules, Shenzhen Leshan Technology Co., Ltd (the applicant) certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process:

Company Name: JOC Australia Inc Physical U.S. Company Address: 18351 Colima Road Ste 585 Rowland Heights, California, 91748 United States of America Agent contact name/Title : Benjamin. Smith/Vice President Agent Email Address: sales@jocinc.org/calvinsui001@gmail.com Tel No.: +1(626) 341 3408 FRN No.: 0033379421 The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed:

Agent Signed (if different to Applicant):

Signed:

Printed name: james_xu Title: General manager Company Name: Shenzhen Leshan Technology Co., Ltd Date: 11/28/2023 Signed:

Printed name: Benjamin. Smith Title: Vice President Company Name: JOC Australia Inc Date: 11/28/2023

* the applicant must designate a contact located in the United States for purposes of acting as the applicants agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process.