BT 5.0 Module MS50SFA Specification BLE* Module Specification Model: MS50SFA Version: V1.0
* Low energy Bluetooth 4.0 and above 1) The Bluetooth trade mark is owned by the Bluetooth SIG Inc. USA. 2) All other trademarks listed herein are owned by their respective owners. 3) All specifications are subject to change without notice. TEL: 0086-755-2103 8160 EMAIL: sales@minewtech.com URL: www.minewtech.com Page 1 BT 5.0 Module MS50SFA Specification Overview The MS50SFA is a compact and very small size Bluetooth 5.0 module with ultra-low power consumption and optional antenna types; it is very suitable for the coin cell battery powered applications. The module is highly integrated that contains all the necessary components from radio to different antenna and a completely implemented Bluetooth protocol stack and pre-flashed UART communication protocol. Features Frequency: 2402 to 2480 MHz Max RF Conducted power: -3.564dBm Single power supply: 1.8 3.9V Range: 10-60 meters Chip: nRF52810 (Nordic) GPIO Quantity: 15 192kB Flash and 24kB RAM (nRF52810) Module size: 15.8 x 12.0 x 2.0 mm ARM Cortex-M4F processor Metal shielding with marking UART communication protocol (Slave / Master optional) 2 optional antenna types: PCB antenna, chip antenna Operating Temperature range: -25 to 85 degree Celsius Certifications CE Certification FCC Certification (FCCID: 2ABU6-MS50SFA) MS50SFA Applications Cycle computer Heart rate monitor Blood pressure monitor Blood glucose meter Weighing machine Thermometer Mobile accessories Sports and fitness sensors Remote controllers / Toys Key fobs and wrist band 3D glasses and gaming controller TEL: 0086-755-2103 8160 EMAIL: sales@minewtech.com URL: www.minewtech.com Page 2 BT 5.0 Module MS50SFA Specification 1. Pin Assignment and Description 1.1 Pin assignment 1.2 Pin description Symbol VCC GND Type Power Power SWDIO Digital I/O Description Power supply Ground System reset (active low). Hardware debug and flash programming I/O programming I/O. SWCLK Digital input Hardware debug and flash programming I/O P0.04 - P0.31 Digital I/O General purpose I/O pin ANT RST Antenna output Digital I/O External antenna Configurable as system RESET pin TEL: 0086-755-2103 8160 EMAIL: sales@minewtech.com URL: www.minewtech.com Page 3 BT 5.0 Module MS50SFA Specification 2. Electronic Characteristic 2.1 Absolute maximum ratings Symbol VCC ANT Min 1.7 Max 3.9
+10 Unit V dBm Condition Input DC voltage at VCC pin Input RF power at antenna pin at receiver Note: The module is not protected against overvoltage or reserved voltages. If necessary, voltage spikes exceeding the power supply voltage specification must be limited to values within the specified boundaries by using appropriate protection devices. 2.2 Maximum ESD ratings Parameter ESD Sensitivity Max 4 750
+/- 8 Unit KV V KV Remarks Human body model Charged device model ESD indirect contact discharge 2.3 Operating temperature range Parameter Storage temperature Operating temperature 2.4 Current consumption Parameter Receiving current Transmission power Sleeping current Min 2.5 RF performance Parameter Receiver input sensitivity Output power Min
-40
-40 Max 85 85 Unit Max 5.4 5.3 1 Unit mA mA uA Remark standard mode transmission power at 0dbm power mode 3 Min
-30 Typical
-93 0 Max
+4 Unit dBm dBm TEL: 0086-755-2103 8160 EMAIL: sales@minewtech.com URL: www.minewtech.com Page 4 BT 5.0 Module MS50SFA Specification 3. Physical Dimension Unit: mm Unit: mm 4. Layout and Soldering Considerations To make sure wireless performance is at its best condition, please layout the module on the carrier board as below instructions. 4.1 Carrier board under the antenna area of the module like the picture;
4.2 Keep out enough area for the antenna area;
4.3 Reflow profiles are to be selected according to standard manufacturing process;
4.4 The soldering temperature should be less than 206;
4.5 The module should be placed far away other low frequency and digital circuits;
4.6 The MS50 series modules contain highly sensitive electronic circuitry and are Electrostatic Sensitive Devices (ESD). Handling the MS50 series modules without proper ESD protection may destroy or damage them permanently. Recommended Layout for the Carrier Board
*PCB: Its the mother board / carrier board. TEL: 0086-755-2103 8160 EMAIL: sales@minewtech.com URL: www.minewtech.com Page 5 BT 5.0 Module MS50SFA Specification 5. UART Commands Please refer to the UART commands document to know more. 6. Package Details Quantity (module) Net Weight Gross Weight Size 7. Ordering information Tray 80 pcs 40.0g 75.0g 20 x 18 x 5 cm Carton 4000 pcs / 50 trays 4.5Kg 9.5Kg 32 x 23 x 40 cm MS50SFAC-003, nRF52810 BT 5.0 Module, PCB Antenna, UART function Description Ordering number 306030058
<END>
TEL: 0086-755-2103 8160 EMAIL: sales@minewtech.com URL: www.minewtech.com Page 6 FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. To m aintain c ompliance w ith F CCs R F E xposure g uidelines, This e quipment s hould b e installed and ope rated w ith m inimum di stance be tween 20c m t he r adiator y our body : U se only the supplied antenna. The final end product must be labeled in a visible area with the following:Contains FCC ID: 2ABU6-MS50SFA