BLE 5.0 & WiFi Gateway Specification BLE WiFi Gateway Model: G1 Version: V1.3.2 Contents Contents ...................................................................................................................................... 1 1.Overview ................................................................................................................................... 2 2.Features .................................................................................................................................... 3 3.Typical Application .................................................................................................................... 3 4.Outside View ............................................................................................................................ 4 5.Electronic Parameters ............................................................................................................... 5 Email: sales@minewtech.com SHENZHEN MINEW TECHNOLOGIES CO LTD Page 1 BLE 5.0 & WiFi Gateway Specification 1. Overview G1 is a Bluetooth 5.0 low energy (BLE) to Wi-Fi connectivity gateway without the uses of smartphones or apps. The G1 gateway collects the data from iBeacon, Eddystone, BLE sensor and other BLE devices, and then sends to the local server or remote cloud server by HTTPs / MQTT/mbed (ARM) protocol with SSL and TLS certification over Wi-Fi / Ethernet / Cellular. The subsequent version G1 Gateway will also implement the connection with BLE devices. This product is a science fiction with a color lamp ring on the top. It can be fixed by sticker or screw thread. Outside View Internal Structure Email: sales@minewtech.com SHENZHEN MINEW TECHNOLOGIES CO LTD Page 2 BLE 5.0 & WiFi Gateway Specification 2. Features General:
1A @ DC 5.0V input, micro-USB 10/100 Ethernet, POE (802.3af) Firmware upgrade OTA Multiple data transportation protocols Local server: TCP / UDP Remote serer / Cloud: HTTP/MQTT/mbed(ARM) with SSL and TLS certification Operating temperature: -15 to 55 WIFI:
Wifi module based on the Mediatek MT7628 580MHz 32-bit Application Processor 2T2R 2.4 GHz with 300 Mbps PHY data rate,802.11b/g/n WiFi Two USB 2.0 Host Connectors and one TF Card slot 128M bytes 16-bit DDR2 RAM 16M bytes SPI NOR Flash RGB LED strip as the status indicator OpenWrt 15.05, Linux distribution for embedded devices. BLE:
BLE module based on the Nordic's nRF52832 with ARM Cortex-M4 64MHz 32-bit processor At least Bluetooth 4.0(Only Bluethooth Low Energy) 3. Typical Application iBeacon / Eddystone / other BLE tag receiver BLE sensor reader / receiver Asset tracking Access control management Advertisement promotion Indoor location and position Industrial automation Email: sales@minewtech.com SHENZHEN MINEW TECHNOLOGIES CO LTD Page 3 BLE 5.0 & WiFi Gateway Specification S1: Bluetooth temperature & humidity sensor E2: 300 to 500 meters MaxBeacon E6: Bluetooth ambient light sensor i3: Waterproof iBeacon & Eddystone i7 : Bluetooth accelerometer sensor C7: Credit card beacon with RFID/NFC G1: Bluetooth & WiFi gateway 4. Appearance G1-C Sign & Slots Feature Description ON/OFF Reset RJ-45 USB IN TF Power On / Off device Factory reset or close/open AP 10/100Mbps Ethernet, 802.3af PoE 2pcs external USB2.0 slot Micro-USB, power input (5.0V DC, 1A) TF card slot (reverse) Email: sales@minewtech.com SHENZHEN MINEW TECHNOLOGIES CO LTD Page 4 BLE 5.0 & WiFi Gateway Specification The meaning of the top LED Strip Lights status is as follows:
Static LED Strip Lights Dynamic white light rotation Dynamic rotation Dynamic breathing lights LED Strip Lights LED Strip Lights go out Indicates that the gateway is staring Indicates that the gateway has been started Indicates that the gateway is not connected to the server Indicates that the gateway is already connected to the server
(Note: The gateway is in the dynamic breathing lights by default, it can step into the energy-saving mode on minute after extinction of lights, you also can set up bright mode in the configuration page if rich enough) Indicates that the gateway is not power or in energy-saving mode 5. Electronic Parameters General Information Color Size Net Weight Accessory White 150x150x36mm 180g 1x USB cable, mental fixing and screws Absolute Maximum Rating Power supply (Vcc) Storage temperature Voltage ripple Max. 5.5 Volts, DC
-40 to 85
+/- 2%
Operation Condition (Recommendable) Operating temperature Humidity Power supply (Vcc)
-15 to 55 Max 95%, Non condensing, relative humidity DC 5.0 (+/- 5%) Current Consumption Powered by Micro-USB Powered by PoE 330mA (LED strip and Wi-Fi works in the same time) 290mA (Wi-Fi only) 340mA (LED strip and Wi-Fi works in the same time) 300mA (Wi-Fi only Email: sales@minewtech.com SHENZHEN MINEW TECHNOLOGIES CO LTD Page 5 BLE 5.0 & WiFi Gateway Specification Wi-Fi RF Performance Wireless Network modes Data rate Frequency band Number of selectable Sub channels Channel Bandwidth Modulation Maximum receive input level Minimum receive input level Transmit Power Carrier Frequency Accuracy Antenna Range Security BLE RF Performance Operation Mode Transmission Power RF Power Accuracy Receiver Sensibility Maximum Received Signal Strength at <0.1% PER Frequency Deviation Antenna Scanning & concurrently process Range IEEE 802.11b/g/n (single stream) Router, Repeater, Cellular (coming soon, Q4/2017) IEEE 802.11b, 1-11Mbps IEEE 802.11g, 6-54Mbps IEEE 802.11n(2.4GHz), 150Mbps 2.412 2.462 GHz 11 channels 20 / 40 MHz OFDM, DSSS, DBPSK,DQPSK, CCK , 16 / 64QAM
- 10dBm (with PER < 8%@11 Mbps)
- 20dBm (with PER < 10%@54 Mbps)
- 20dBm (with PER < 10%@MCS7)
- 87dBm (typ. with PER < 8%@11 Mbps)
- 70dBm (typ. with PER < 10%@54 Mbps)
- 70dBm (typ. with PER < 10%@MCS7) 18.13dBm (typical)@ 802.11b 17.36dBm (typical)@ 802.11g 18.8dBm (typical)@ 802.11n
+/- 20ppm (crystal: 16MHz +/-10ppm in 25) FPC antenna up to 100 meters( in open space) WPA / WPA2 LAN mode Ranges from -30 to +4dBm
+/- 4 dB
-108 dBm @250kbps, 0.1% BER
-93 dBm @1Mbps, 0.1 %BER 0dBm
+/-250 kHz @BLE Flexible FPC antenna 200 BLE devices per second 300 meters in open space (max.) Email: sales@minewtech.com SHENZHEN MINEW TECHNOLOGIES CO LTD Page 6 FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.