Wireless Charging Power Bank Instruction Manual MSL-W198Q 5 34 1 c. d. 2. a. b. 3. a. b.
*
2 7 6 Features:
LED Indicator 1. ON/OFF button 2. Micro Input 3. Lightning Input 4. USB port 5. Wireless Input Pad 6. Wireless Output Pad 7. Silicone Wraps 8. Whats included:
1 x 6000 mAh Power Bank 1 x 2-in-1 Charging Cable 1 x Instruction Manual Micro Input: DC 5V 2A Lightning Input: DC 5V 1A USB Output 1/2: DC 5V 2A(MAX) Wireless Input: 5V 0.8A Wireless Output: 5V 1A LED Indicators:
ON/OFF Button: Press once to to view the remaining power capacity. LED indicator will show Green once the Power bank is on wireless charging standby mode. Instructions:
1. a. b. Charging the power bank:
Charge the power bank fully before usage. Using the built-in 2-in-1 charging cable, AC adapter or USB port of a computer, insert the 2-in-1 tip (the side with pins upwards) into power bank micro input. charging, and will stop once fully charged. To Wireless Charge the power bank, place power bank(6) on a wireless charging surface, Charging mobile phones and other electronic devices:
Connect the 2-in-1 cable to your mobile phone. Android device: The tip with pins upwards;
iOS device: The tip without pins upwards. Connect the other end to the power bank it will begin to charge automatically. Remove the USB cable from your mobile device when it is fully charged. Charging Mobile phones and other electronic devices with wireless output. Place wireless charging enable device on Wireless Charging Output Pad(7). The device begins to charge with LED indicator will turn RED. You can fasten your phone on the power bank via silicone wrap of the power bank(8) during wireless charging. Note: In order to charge devices, use only the accessory cable or the cable included with your own device by the manufacturer. SAFETY PRECAUTIONS:
WARNING-When using this product, basic precautions should always be followed:
Read all the instructions before use. Never store or use this product in temperatures below 32F (0C) or above 115F (45C). Do not overcharge your phone. The unit may become hot under excessive use. Remove your phone once it is fully charged. Never charge your phone for more than 7 hours at a time. The unit will only achieve full performance after 2 or 3 completed charge and discharge cycles. To reduce the risk of injury, close supervision is required when the product is used near children. Do not expose the device to moisture. Do not use the device in excess of its output rating. Overload outputs above the Do not use the device if damaged or 1. 2. 3. 4. 5. 6. 7. 8. 9. explosion or risk of injury. Do not disassemble the device. For 10. professional. Incorrect reassembly may 11. or temperatures above 104F (40C) may result in explosion. To ensure product safety, ensure that 12. identical replacement parts. Attachments on the back of your phone 13. can impede the effectiveness of the wireless charger, and lead to overheating. Please remove attachments from the phone before charging on this device. FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator your body: Use only the supplied antenna MADE IN CHINA