CC2640S1 Overview Radioland would like to announce a low-cost and low-power consumption module which has all of the Bluetooth Smart 4.1 functionalities. The CC2640S1 module fully supports the single mode Bluetooth Low Energy operation, and the output power can support class 2. The module provides the ability to either put your entire application into the integrated ARM Cortex M3 microcontroller, or use the module in Network Processor mode in conjunction with the microcontroller of your choice. RF Cores dedicated ARM Cortex M0 improves system performance and frees up FLASH memory for custom applications. Feature Built in CC2650F128 Bluetooth Smart
(BLE 4.1) System-On-Chip (SOC) 128 kB Flash / 20 kB SRAM RF Receive Sensitivity: -96 dBm Size: 11.8mm x 15.8mm Operating Voltage: 1.8V to 3.8V Operating Temperature: -40 to +85C 8.4 mA Transmit Mode 7.4 mA Receive Mode 1A Standby (SRAM/CPU retention and RTC running) with quick 100 s start up 200nA Shutdown 61A/MHz Active CPU Current Drivers, Bluetooth Low Energy Controller, and bootloader in ROM Flexible peripheral set On board 32 kHZ and 24 MHz Crystals Worldwide Acceptance:
Applications Consumer electronics Mobile phone accessories Sports & Fitness equipment HID applications Home and Building Automation, Lighting Control, Alarm and Security Electronic Shelf Labeling, Proximity Tags 5F.BlockA2 | Hangcheng Industry Zone | ChenTian | Xixiang Town | Baoan district | Shenzhen,P.R.C Tel:+86 0755 66621530 |
www.radioland-china.com |
sales@radioland-china.com Electrical Characteristics ITEM TEST REQUIREMENT REMARKS Voltage supply Center frequency Frequency error Modulation 1.83.8V 24022480MHz 50KHz O-QPSK Receiving sensitivity Receiving current Transmitting current Sleep consumption At power mode2 Sleep consumption At power mode3 Transmit distance Antenna Module size
-97dBm 5.9mA 9.1mA 1uA 0.1uA
>60M 50ohm 11.8mm*15.8mm DC Programmable High gain Mode TX Power 5dBm Sleep Timer ON External interrupts BER<0.1%
RECOMMENDED OPERATING CONDITIONS Operating ambient temperature range, TA Operating supply voltage MIN
-30 1.8 MAX 85 3.8 UNIT C V CAUTION:
ESD sensitive device. Precautions should be used when handing the device in order to prevent permanent damage. 5F.BlockA2 | Hangcheng Industry Zone | ChenTian | Xixiang Town | Baoan district | Shenzhen,P.R.C Tel:+86 0755 66621530 |
www.radioland-china.com |
sales@radioland-china.com Dimensions RL-CC2640-S1 Pin Assignment 1 13 36 24 14 23 5F.BlockA2 | Hangcheng Industry Zone | ChenTian | Xixiang Town | Baoan district | Shenzhen,P.R.C Tel:+86 0755 66621530 |
www.radioland-china.com |
sales@radioland-china.com Pin Num. Pin Name Pin Type Description RL-CC2640-S1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 VDDS GND VDD_EB DIO_0 DIO_1 DIO_2 DIO_3 DIO_4 DIO_5 GND VDD_EB JTAG_TCK JTAG_TMS nREST DIO_7 DIO_8 DIO_9 DIO_10 DIO_11 DIO_12 DIO_13 DIO_14 nREST Power Ground Power Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O 1.8 V to 3.8 V GPIO supply(1) ground 1.8 V to 3.8 V main chip supply(1) GPIO, Sensor Controller GPIO, Sensor Controller GPIO, Sensor Controller, High drive capability GPIO, Sensor Controller, High drive capability GPIO, Sensor Controller, High drive capability GPIO, High drive capability, JTAG_TDO ground 1.8 V to 3.8 V main chip supply(1) JTAG TCKC JTAG TMSC, High drive capability Reset, active-low. No internal pullup Digital I/O Ground Power Digital I/O Digital I/O Digital input Digital/Analog I/O GPIO, Sensor Controller, Analog Digital/Analog I/O GPIO, Sensor Controller, Analog Digital/Analog I/O GPIO, Sensor Controller, Analog Digital/Analog I/O GPIO, Sensor Controller, Analog Digital/Analog I/O GPIO, Sensor Controller, Analog Digital/Analog I/O GPIO, Sensor Controller, Analog Digital/Analog I/O GPIO, Sensor Controller, Analog Digital/Analog I/O GPIO, Sensor Controller, Analog Digital input Reset, active-low. No internal pullup 5F.BlockA2 | Hangcheng Industry Zone | ChenTian | Xixiang Town | Baoan district | Shenzhen,P.R.C Tel:+86 0755 66621530 |
www.radioland-china.com |
sales@radioland-china.com Layout Suggestion CC2640S1 bluetooth module serial level should be 3.3 V, if the connection and 5V level system need to increase the level conversion chip. Bluetooth signal is highly affected by the surrounding,such as trees, metal, wall can have certain absorption on the bluetooth signal or block, so the installation is not recommended in the metal case. Due to metal will weaken the function of antenna, it is suggested that Lay in the module board,don't lay GND and a line under the antenna module, it is best to hollow out. NOTE:
Additional information on the Texas Instruments CC2650 device can be found in the companys latest datasheet release at http://www.ti.com/product/CC2650 5F.BlockA2 | Hangcheng Industry Zone | ChenTian | Xixiang Town | Baoan district | Shenzhen,P.R.C Tel:+86 0755 66621530 |
www.radioland-china.com |
sales@radioland-china.com FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: 2AGUT-CC2640S1 Or Contains FCC ID: 2AGUT-CC2640S1 when the module is installed inside another device, the user manual of this device must contain below warning statements;
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product Any company of the host device which install this modular with limit modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C : 15.247 and 15.209 requirement, Only if the test result comply with FCC part 15C : 15.247 and 15.209 requirementthen the host can be sold legally.