RadioLand Smart Wireless Solutions CC2530-A1Module General description The CC2530-A1 RF Module is a low-power, highly integrated 2.4-GHz transceiver that suitable for systems targeting compliance with worldwide radio-frequency. Its a true system-on-chip solution for 2.4-GHz IEEE802.15.4, ZigBee and RF4CE applications. Features z 2.4-GHz IEEE802.15.4 compliant RF transceiver z Programmable output power up to 4.5dBm z Accurate digital RSSI/LQI support z Suitable for systems targeting compliance with worldwide radio-frequency z Data rate: 250kbps z 256KB in-system programmable flash, customization 32-,64-,128KB z Two 64 bytes FIFO for TX & RX buffer z CSMA/CA hardware support z Battery monitor and temperature sensor z AES security coprocessor z 8KB RAM with retention in all power mode z 32-kHz sleep timer with capture z Wide Supply-Voltage Range (2 V3.6 V) Applications z 2.4-GHz IEEE 802.15.4 systems z RF4CE remote control systems (64-KB flash and higher) z AMR Automatic Meter Reading z Two-way RKE Remote Keyless Entry z Home and building automation z Wireless alarm and security systems z z Wireless Light Dimming z Wireless sensor networks Industrial monitoring and control
1 RadioLand Smart Wireless Solutions Electrical Characteristics CC2530-A1 Module ITEM TEST REQUIREMENT REMARKS Voltage supply Center frequency Frequency error Modulation Output power Receiving sensitivity Receiving current Receiving current Transmitting current Sleep consumption At power mode2 Sleep consumption At power mode3 Transmit distance Antenna module size 2405-2480MHz 2.03.6V 24002483.5MHz
50KHz O-QPSK 0dBm
-93dBm 20.2mA 17.9mA 18.2mA 1uA 0.5uA
>80M 50ohm 15*24mm DC Programmable High gain Mode High gain mode Standard mode TX Power 0dBm Sleep Timer ON External interrupts BER<0.1%
RECOMMENDED OPERATING CONDITIONS Operating ambient temperature range, TA Operating supply voltage MIN MAX
-30 85 2 3.6 UNIT C V CAUTION:
ESD sensitive device. Precautions should be used when handing the device in order to prevent permanent damage.
2 RadioLand Smart Wireless Solutions Pin Assignment Module PIN PIN name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 CC-Debugger and test boards GND RESET P0.0 P0.1 P0.2 P0.3 P0.4 P0.5 P0.6 P0.7 P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 DP DM P1.6 P1.7 P2.0 P2.1 P2.2 VCC GND ANT CC2530-A1 Module Description Ground N_RESET active-low Digital I/O Digital I/O Digital I/O RXD Digital I/O TXD Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O 20-mA drive capability Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Debug data Digital I/O Debug clock IC PIN 1, 20 19 18 17 16 15 14 13 12 11 9 8 7 6 5 2 3 5 37 36 35 34 214,24,27-31 23.6V power-supply 1, Ground 50ohm/External antenna
3 RadioLand Smart Wireless Solutions Outline and Size CC2530-A1 Module NOTE:
Additional information on the Texas Instruments CC2530 device can be found in the companys latest datasheet release at http:// www.ti.com/product/CC2530
4 FCC Statement
Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)Thisdevicemaynotcauseharmful
interference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
NOTE:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttoPart15oftheFCCRules.
Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,
usesandcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterference
toradiocommunications.However,thereis noguaranteethatinterferencewillnotoccurinaparticularinstallation.If thisequipmentdoes
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouragedtotrytocorrecttheinterferencebyoneormoreofthefollowing
measures:
Reorientorrelocatethereceivingantenna.
Increasetheseparationbetweentheequipmentandreceiver.
Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.
Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
FCCRadiationExposureStatement
Themodularcanbeinstalledorintegratedinmobileorfixdevicesonly.Thismodularcannotbeinstalledinanyportabledevice,forexample,
USBdongleliketransmittersisforbidden.
ThismodularcomplieswithFCCRFradiationexposurelimitssetforthforanuncontrolledenvironment.Thistransmittermustnotbecolocated
oroperatinginconjunctionwithanyotherantennaortransmitter.Thismodularmustbeinstalledandoperatedwithaminimumdistanceof20
cmbetweentheradiatoranduserbody.
IftheFCCidentificationnumberisnotvisiblewhenthemoduleisinstalledinsideanotherdevice,thentheoutsideofthedeviceintowhichthe
module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:
ContainsTransmitterModuleFCCID:2AGUTCC2530A1OrContainsFCCID:2AGUTCC2530A1
whenthemoduleisinstalledinsideanotherdevice,theusermanualofthisdevicemustcontainbelowwarningstatements;
1.ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:
(1)Thisdevicemaynotcauseharmfulinterference.
(2)Thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
Thedevicesmustbeinstalledandusedinstrictaccordancewiththemanufacturer'sinstructionsasdescribedintheuserdocumentationthat
comeswiththeproduct
Any company of the host device which install this modular with limit modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C : 15.247 and 15.209 requirement,Only if the test result comply with FCC part 15C : 15.247 and 15.209 requirementthen the host can be sold legally.