FCC ID: 2AYANEVP01 New Energy Vehicle Detection Tool

www.newsmartsafe.com iSmartEV P01 User Manual Copyright Information Copyright 2021 by SHENZHEN SMARTSAFE TECH CO.,LTD. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of SMARTSAFE. Neither SMARTSAFE nor its affiliates shall be liable to the purchaser of this unit or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: Accident, misuse, or abuse of this unit, or unauthorized modifications, repairs, or alterations to this unit, or failure to strictly comply with SMARTSAFE operating and maintenance instructions. SMARTSAFE shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original SMARTSAFE Products or SMARTSAFE Approved Products by SMARTSAFE. All information, specifications and illustrations in this manual are based on the latest information available at the time of printing. SMARTSAFE reserves the right to make changes at any time without prior written or oral notice. Trademark Information In countries where any of SMARTSAFE is a registered trademark of SHENZHEN SMARTSAFE TECH CO.,LTD. in China and other countries. All other SMARTSAFE trademarks, service marks, domain names, logos, and company names referred to in this manual are either trademarks, registered trademarks, service marks, domain names, logos, company names of SMARTSAFE or are otherwise the property of SMARTSAFE or its affiliates. the SMARTSAFE trademarks, service marks, domain names, logos and company names are not registered, SMARTSAFE claims other rights associated with unregistered trademarks, service marks, domain names, logos, and company names. Other products or company names referred to in this manual may be trademarks of their respective owners. You may not use any trademark, service mark, domain name, logo, or company name of SMARTSAFE or any third party without permission from the owner of the applicable trademark, service mark, domain name, logo, or company name. You may contact SMARTSAFE by visiting the website at www.newsmartsafe.com, or writing to SHENZHEN SMARTSAFE TECH CO.,LTD., 3310, Building 11, Tianan Cloud Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China, to request written permission to use Materials on this manual for purposes or for all other questions relating to this manual. I www.newsmartsafe.com iSmartEV P01 User Manual To avoid personal injury, property damage, or accidental damage to the product, please read all the information in this chapter before using the product. Operation Specification For New Energy Vehicle Safety Maintenance 1. Identification of high voltage components: The orange wiring harnesses of the vehicle are all high voltage wires. 2. High voltage parts: power battery pack, high voltage distribution box, on-board charger, driving motor controller and DC-DC assembly, electric power assembly, integrated compressor, PTC heater, maintenance switch. 3. When repairing the high voltage system, the power supply of the vehicle must be OFF (and the vehicle is in the non-charging state), and remove the maintenance switch; After the emergency maintenance switch is removed, it shall be kept by full-time guardianship personnel, and ensure that no one will plug it in during the maintenance process. Notice: When the high voltage distribution box needs to be repaired or replaced, remove the positive and negative high voltage connectors connected to the battery pack carefully, and wrap the exposed wires with electrical tape to avoid electric shock. 4. Five minutes after turning off the emergency maintenance switch, use a multimeter to measure the high voltage circuit and ensure that there is no power before checking and repairing the high voltage system. 4.1 Measure the voltage between the positive electrode of the battery pack and the body to preliminarily determine whether there is electric leakage. If the voltage is greater than or equal to 50V, it indicates that there is a leakage in the battery pack. Stop the operation immediately. 4.2 When using a multimeter the correct measurement range. The accuracy level of the multimeter should not be lower than 0.5, and the measurement range should not be less than or equal to 600V. Please follow "One-hand Operation" principle;

4.3 One pen line of the multimeter is equipped with an insulated alligator clip (the voltage is required to be 3KV; the overcurrent capacity is greater than 5A). During measuring, clamp the clip to a terminal of the circuit first, and then connect the other pen to the terminal to measure the reading. Only hold the pen with one hand during each measurement; do not the pen during measurement. 5. The maintenance switch shall not be assembled during low-voltage debugging. In high-voltage debugging, the full-time guardian shall instruct the assembly and maintenance switch. to measure high voltage, select touch the metal part of II www.newsmartsafe.com iSmartEV P01 User Manual 6. High voltage debugging must be carried out under the premise of good low voltage debugging, so as to determine whether the battery has leakage. If there is leakage, it should be checked in time, and high voltage debugging cannot be carried out. 7. During disassembling and installing the power battery pack assembly; wrap the high-voltage wiring harness connector connected to the high-voltage distribution box with insulation tape. Do not damage the wiring harness during disassembly and installation to avoid electric shock. 8. During repairing or replacing parts that pass through the sheet metal holes of the body, such as high-pressure wiring harnesses and tubing, pay attention to check whether the protection with the sheet metal of the body is normal to avoid the wear of the wiring harnesses and tubing NOTES the shift 1. Maintain a safe environment for vehicle testing at all times. 2. Do not operate the detection equipment while driving the vehicle to avoid distraction and causing an accident. 3. Before starting the engine, you should pull the handbrake, especially the front transmission) or [P] gear lever in neutral (manual wheel, and put

(automatic transmission) so as not to start the engine and make the vehicle injure people. 4. The exhaust gas from the engine contains a variety of toxic compounds (such as hydrocarbons, carbon monoxide, nitrogen oxides, etc.), which will lead to slow injury or death. The vehicle under test response and even serious personal should be parked in a well-ventilated place during operation. 5. Take extreme care when working around ignition coils, distributor caps, ignition lines and plugs. These components generate dangerous voltages when the engine is running. 6. To avoid damaging the testing equipment or generating incorrect data, please ensure that the vehicle battery is fully charged and that the connection of the vehicle diagnostic seat is clean and safe. 7. The vehicle battery liquid contains sulfuric acid, sulfuric acid is corrosive to the skin, so you should avoid direct contact between the battery liquid and the skin during the operation, especially do not splash it into the eyes, and do not put it close to the fire. 8. Keep clothing, hair, hands, tools, testers, etc. away from running or hot engine parts. 9. Please use the charger that comes with it. The Company will not be III www.newsmartsafe.com iSmartEV P01 User Manual responsible for any damage or loss caused by the use of other chargers not designated by the Company. 10. Keep the testing equipment dry and clean, away from gasoline, water and grease. When necessary, clean the surface of the equipment with a clean cloth coated with a mild detergent. 11. All internal repairs to test equipment must be performed by authorized maintenance organizations or authorized technicians. Attempting to disassemble or modify the device will void the warranty. This manual uses the following conventions. PROMPT Prompt information provides helpful instructions, tips, and suggestions. Example:

information such as additional operation Prompt: The VIN code is usually located on the driver's side, in the lower right corner of the front windshield. The exact location varies from car to car. A VIN code is generally composed of 17 standard characters. The VIN code characters can contain the uppercase letters A to Z and the numbers 1 to 0, but the letters I, O, and Q are not usually used to avoid mispronunciation. WARNING It indicates an imminent hazard that, if unavoidable, will result in death or serious injury to the operator or bystander. Example:

Warning: Reading a fault code during troubleshooting a vehicle is only a small step in the diagnostic process. The vehicle fault code is only used as a reference, and parts cannot be replaced directly on the basis of the given fault code definition. Each fault code has a set of test procedures, and the service technician must strictly follow the operating instructions and procedures described in the vehicle service manual to confirm the root of the fault. DANGER It indicates an imminent hazard that, if unavoidable, will result in death or serious injury to the operator or bystander. Example:

Danger: You must drive the vehicle in order to perform troubleshooting. Please find someone else to help you. It is dangerous to drive and operate diagnostic equipment at the same time, which can cause severe traffic accidents. IV www.newsmartsafe.com iSmartEV P01 User Manual Table of Contents 1. Packing List .............................................................................................. 1 2. Product Introduction ................................................................................6 2.1 Overview ................................................................................................ 6 2.2 iSmartEV P01 Tablet ............................................................................. 6 2.3 iSmartEV BOX Detection box ................................................................ 8 2.4 Technical parameters ............................................................................ 8 3. Initial Use ................................................................................................ 10 3.1 Charge the Tablet ................................................................................ 10 3.2 Turn On/Off .......................................................................................... 10 3.3 Network Connection .............................................................................10 3.4 Registration and Upgrade .................................................................... 11 4. Getting Started ....................................................................................... 14 4.1 Main interface and bottom navigation bar ............................................14 4.2 Communication settings .......................................................................15 5. Battery Pack Detection .......................................................................... 17 6. Quick Charging Port Detection ............................................................. 22 7. Vehicle Detection ................................................................................... 25 7.1 Intelligent Detection ............................................................................. 25 7.2 Manual Selection ................................................................................. 25 8. Endoscope .............................................................................................. 37 9. Current Clamp ........................................................................................ 37 10. ADAS Calibration ................................................................................. 37 10.1 Activate ADAS calibration function .................................................... 37 10.2 Start calibration .................................................................................. 38 11. Special Functions .................................................................................41 11.1 A/F Reset ........................................................................................... 41 11.2 Electronic Parking Brake Reset ......................................................... 41 11.3 Oil Reset Service ............................................................................... 41 11.4 Steering Angle Calibration ................................................................. 41 V www.newsmartsafe.com iSmartEV P01 User Manual 11.5 Battery Maintenance System Reset ...................................................41 11.6 ABS Bleeding .....................................................................................42 11.7 Throttle learning ................................................................................. 42 11.8 Tire Pressure Monitor System Reset ................................................. 42 11.9 Diesel Particulate Filter (DPF) regeneration ...................................... 43 11.10 Gearbox Matching ............................................................................43 11.11 Gear Learning .................................................................................. 43 11.12 Motor Angle Calibration Diagnosis ...................................................43 11.13 Coolant Bleed .................................................................................. 43 11.14 Engine Power Balance Monitoring Diagnosis .................................. 43 11.15 IMMO Service .................................................................................. 44 11.16 High Voltage Battery Diagnostics Diagnosis ....................................44 11.17 Gas Particulate Filter Regeneration Diagnosis ................................ 44 11.18 Transport Mode ................................................................................44 11.19 Tire Reset ........................................................................................ 44 11.20 Windows Calibration ........................................................................ 44 11.21 AdBlue Reset ................................................................................... 44 11.22 NOx Sensor Reset ........................................................................... 44 11.23 Injector Coding .................................................................................45 11.24 Airbag Reset .................................................................................... 45 11.25 Stop/Start Reset ...............................................................................45 11.26 Sunroof Initialization .........................................................................45 11.27 Suspension Calibration .................................................................... 45 11.28 Odometer Calibration Diagnosis ...................................................... 45 11.29 Language Change ........................................................................... 46 11.30 Intelligent Cruise Control System Diagnosis ....................................46 11.31 AC System Relearn/Initialization Diagnosis .....................................46 11.32 Seats Calibration ..............................................................................46 11.33 AFS (Adaptive Front-lighting System) Reset ................................... 46 12. Software upgrade ................................................................................. 47 12.1 Upgradable ........................................................................................ 47 12.2 Downloaded ....................................................................................... 47 13. Remote diagnosis ................................................................................ 49 VI www.newsmartsafe.com iSmartEV P01 User Manual 13.1 Remote diagnosis request ................................................................. 49 13.2 Assist others remotely ........................................................................50 13.3 Contact list ......................................................................................... 51 14. Personal center .................................................................................... 53 14.1 My connector ..................................................................................... 53 14.2 Connector activation .......................................................................... 53 14.3 Firmware fix ....................................................................................... 53 14.4 Personal information .......................................................................... 54 14.5 Diagnostic unit settings ...................................................................... 54 14.6 Diagnostic software clearing .............................................................. 54 14.7 About ..................................................................................................55 14.8 Exit the current account ..................................................................... 55 15. Detection report ....................................................................................56 16. Other... .................................................................................................. 58 16.1 Tablet setting ..................................................................................... 58 16.2 Diagnostic feedback ...........................................................................60 16.3 File management ............................................................................... 61 16.4 Remote control ...................................................................................62 16.5 Browser ..............................................................................................62 16.6 System OTA upgrade ........................................................................ 62 16.7 Photo album .......................................................................................63 16.8 Screen recording ................................................................................63 16.9 Player .................................................................................................63 16.10 Mail .................................................................................................. 63 16.11 Photograph ...................................................................................... 63 17. Frequently Asked Questions ...............................................................64 FCC Warnning ............................................................................................ 66 Warranty.. ................................................................................................... 67 VII www.newsmartsafe.com iSmartEV P01 User Manual 1. Packing List Each machine has the same general accessories, but the product configuration is different for different markets. For details, please consult the local dealer or refer to the packing list delivered randomly with the product. Main Frame and Accessories No. Name Q'TY Reference Picture 1 iSmartEV P01 Tablet 1 2 iSmartEV BOX 1 3 4 OBD II Extension Cable Charger 5V 3A 1 1 1 www.newsmartsafe.com iSmartEV P01 User Manual USB Cable Type-C USB Cable Type-B Power Adapter 12V 5A Password Envelop Quick Use Guide User Manual Packing List 1 1 1 1 1 1 1

Special Connector for Battery Pack Name Q'TY Reference Picture Special connector for battery pack TL-100R 1 5 6 7 8 9 10 11 No. 1 2 www.newsmartsafe.com iSmartEV P01 User Manual 2 3 4 5 6 7 8 9 10 11 Special connector for battery pack TL-101R Special connector for battery pack TL-102R Special connector for battery pack TL-104Y Special connector for battery pack TL-105R Special connector for battery pack TL-106R Special connector for battery pack TL-107R Special connector for battery pack TL-108Y Special connector for battery pack TL-109Y Special connector for battery pack TL-110B Special connector for battery pack TL-112B 1 1 1 1 1 1 1 1 1 1 3 www.newsmartsafe.com iSmartEV P01 User Manual 12 13 14 15 Special connector for battery pack TL-113Y Special connector for battery pack TL-114Y Special connector for battery pack TL-126R Special connector for battery pack TL-130R 1 1 1 1 Battery Pack Jumper and Adapter Cable No. Name Q'TY Reference Picture 1 2 3 4 Battery pack jumper

(Jump-8) Adapter Cable 1 Adapter Cable 2 Adapter Cable 3 1 4 4 4 4 www.newsmartsafe.com iSmartEV P01 User Manual 5 6 7 8 9 Adapter Cable 4 Adapter Cable 5 Adapter Cable 6 Adapter Cable 7 Adapter Cable 8 10 Adapter Cable 9 4 4 4 4 4 4 5 www.newsmartsafe.com iSmartEV P01 User Manual 2. Product Introduction 2.1 Overview iSmartEV P01 New energy vehicle battery pack detector is a professional comprehensive testing equipment for new energy vehicles developed by SmartSafe Company. The equipment supports new energy vehicle testing and vehicle battery pack testing functions, and has integrated professional measurement tools such as oscilloscope, multimeter, insulation testing, current clamp etc. for new energy vehicles. Support deep system detection of battery packs of various brands, and support reading of parameters such as the current SOC/SOH, monomer/module voltage, for battery packs. input/output current and power, and battery temperature etc. Automatically calculate the total voltage, voltage difference, maximum

/minimum voltage and other indicators, and automatically label abnormal data. the reading/cleaning of battery pack fault code, special function, actuation test and other detection functions. vehicle whole vehicle detection, Support new energy support 2.2 iSmartEV P01 Tablet 6 www.newsmartsafe.com iSmartEV P01 User Manual No. Name and Description 1 2 3 4 5 6 7 8 9 10.1-inch touch screen Front facing camera Power indicator light Red during charging and green after fully charged. Handle Volume -

Volume+

Power button/screen lock button Press the button for about 3 seconds to start the machine when the power is off. Press this key to wake up/close the screen when the power is on. Press the button for more than 3 seconds to select shutdown or restart when the power is on; Press the button for about 8 seconds to force the shutdown. Microphone USB Type-C Used for connecting to power adapter for charging or connecting to computer for data transmission. 10 USB Type-A Used for connecting to USB devices or function expansion 7 www.newsmartsafe.com iSmartEV P01 User Manual modules. Flash light Rear camera Holder Loudspeaker 11 12 13 14 2.3 iSmartEV BOX Detection box The device is a Vehicle Communication Interface (VCI) device, which is used to connect the vehicle diagnosis seat or battery pack low-voltage signal communication interface for data collection, and then send the data to the host for analysis. No. Name and Description 1 2 3 4 5 6 7 8 USB Type-B DC 12V Power supply jack Wi-Fi indicator USB indicator Bluetooth indicator Vehicle communication indicator Power supply indicator OBD-II port 2.4 Technical parameters 2.4.1 iSmartEV P01 8 www.newsmartsafe.com iSmartEV P01 User Manual Item Specification Parameters Operation System Android 7.1 CPU Internal Storage Storage 8-core processor2.0GHz 4GB 128GB Display Screen 10.1 inch1920 * 1200 resolution touch screen Front Facing Camera 8 million pixels Rear Camera 13 million pixels Wi-Fi 2.4GHz/5GHz Wi-Fi Communication Wi-Fi, Bluetooth, USB Battery 3.8V/9360mAH Working Temperature 0 ~45 Storage Temperature

-20 ~70 2.4.2 iSmartEV BOX Item Specification Parameters CPU System Internal Storage Storage Port Cortex A7 + Cortex-M7 Linux 256M 8GB Type BODBII-16DC-IN Communication Wi-Fi, Bluetooth, USB Working Voltage Working temperature DC 9~36V 0 ~50 Storage temperature

-20 ~70 9 www.newsmartsafe.com iSmartEV P01 User Manual 3. Initial Use 3.1 Charge the Tablet Warning: Please use the charger that comes with the product for charging. We are not responsible for any damage or economic loss caused by charging with a charger other than the one designated by us. Please follow the following steps to charge the iSmartEV P01 tablet:

1. Connect one end of the charging cable to the USB port on the charger and the other end to the Type-C port on the host, and connect the charger to the power socket. 2. If the power indicator of the host is red and the battery identifier on the screen is displayed , then the battery is being charged. 3. When the power indicator of the host is green, the charging is complete. In this case, the battery identifier is displayed . Note:

If the device has not been used for a long time or the battery power of the device is exhausted, you may not be able to turn it on normally when charging. This is a normal phenomenon. Please charge the device for a period of time and then try to start the device. The battery can be recharged. But because the battery is a wear and tear product, after a long time of use, the standby time of the device will be shortened. So please avoid frequent and repeated charging to prolong the battery life. 3.2 Turn On/Off 3.2.1 Turn On Press and hold the power button on the device until the screen lights up. 3.2.2 Turn OFF Press and hold the power button on the device until the shutdown prompt dialog box pops up on the screen, click [Turn off] to shut down the device or click

[Restart] to restart the device. 3.3 Network Connection When using the device for the first time, you need to register a personal account, activate the VCI connector, and upgrade the detection software or APK. In this case, the device must be connected to the Internet. For details on wireless network connection, please refer to chapter 16.1. 10 www.newsmartsafe.com iSmartEV P01 User Manual 3.4 Registration and Upgrade During the first use, the user needs to follow the following operations:

Register an Account VCI connector Activation Complete Registration Software Download Note: Before registration, ensure that the network connection to the host is normal and stable. On the main interface, click [Personal Center] -> [Login], and the following dialog box will pop up:

(If you are a new user, follow Section A.)

(If you are registered, please refer to Section B for login.)

(If you forget your password, please refer to Section C to reset it.) A. If you are a new user, please click [New User Registration] to enter the registration page 11 www.newsmartsafe.com iSmartEV P01 User Manual In the figure above, fill in the registration information in turn (the item with * is required). After the account information is filled in, click [Register], and the system will enter the interface of connector activation. Enter the product serial number and activation code. The product serial number and activation code can be obtained from the password envelope in the package box. Note: If you skip the activation step here, you can also go to [Personal Center] ->

[Connector Activation] to activate after entering. Click [Activate] to complete the registration. 12 www.newsmartsafe.com iSmartEV P01 User Manual Click [Confirm] to enter the software upgrade interface. On the software upgrade page, click [One-click Upgrade] to start downloading. After the download is complete, the system will automatically install the software. Note: During the upgrade, ensure that the network connection is normal. In addition, due to the large number of software, it may take a long time (depending on the network speed). Please wait patiently. B. If you have already registered, input the user name and password and click

[Login] to enter the account. Prompt: The device has the user information memory function. If multiple accounts have logged in to the device, click the triangle drop-down button behind the user name input box to select the corresponding account to log in. C. If you forget the password, please click [Forget Password] and then set the new password according to the prompts on the screen. 13 www.newsmartsafe.com iSmartEV P01 User Manual 4. Getting Started 4.1 Main interface and bottom navigation bar 4.1.1 Main interface The main interface of modules:

iSmartEV P01 mainly includes the following functions Items Description Battery Pack Detection This function is used for deep system detection of the vehicle battery pack. Vehicle Detection Quick Charging Port Detection Special Functions Detection report Software Upgrade Endoscope Use this function to test the electric control system of the whole vehicle. This function module needs to be used with iSmartEV FC01 new energy vehicle battery pack detection gun (optional), which can quickly detect the vehicle battery pack. Use this function for special maintenance and adjustment etc. functions such as vehicle Check and manage the detection report and records. One-click upgrade of battery pack software, model software, operating system, client, and firmware is supported. The function module works with an endoscope device

(optional) to detect invisible or inaccessible parts of the engine, tank and brake system. For details, refer to the user fuel manual delivered with the endoscope device. 14 www.newsmartsafe.com iSmartEV P01 User Manual Current Clamp ADAS Calibration Remote Diagnosis Personal Center Other This module works with the new energy current clamp test and DC voltage test. For

(optional) for AC/DC current details, refer to the user manual enclosed with the new energy current clamp. This module works with the specified ADAS calibration tool for ADAS

(purchased separately, e.g., ADAS Mobile)

(Advanced Driver Assistance System) calibration operations. The function module is used to remotely assist the user to diagnose the vehicle. Check and manage VCI connectors, firmware fix and personal information etc. Including functional modules such as tablet settings, diagnostic feedback, file management, remote control, browser, system OTA upgrade, photo album, screen recording, player, email and photograph etc. as well as system APP. 4.1.2 Bottom navigation bar The bottom navigation bar contains the following buttons:

Icon Name and Function Description Browser-click this button the start the browser Screenshot-click this button to capture and save the current screen image. The screenshot is saved in the Screenshots folder. VCI connection indicator-after the host is successfully connected to the VCI connector, this button lights up in green. Backstage Management - Click this button to display a list of recently used application thumbnails. Click on any of the thumbnails to open the corresponding program, hold d the thumbnail to slide it left and right to close the corresponding program. Main interface-click to return to the main interface Return-click to return to previous page 4.2 Communication settings The main connection modes of communication and USB cable communication. the host and VCI connectors are Wi-Fi 15 www.newsmartsafe.com iSmartEV P01 User Manual 4.2.1 Wi-Fi communication The host will prompt the user to register and activate the VCI connector during the first use. Once the activation is complete, the host will automatically match with the VCI connector and establishes a Wi-Fi connection. At this time the VCI connector icon indicator of the VCI connector is also on. at the bottom of the host screen lights up and the Wi-Fi 4.2.2 USB communication When the host and VCI connectors are connected through USB cables, the system automatically switches to USB communication mode. At this time the VCI connector icon indicator of the VCI connector will also light up. at the bottom of the host screen will light up, and the USB 16 www.newsmartsafe.com iSmartEV P01 User Manual 5. Battery Pack Detection This function is used to check the detailed data and fault information of battery pack, helping users to quickly determine the abnormal status and fault point of battery pack. Danger: The personnel who operate the battery pack test must wear protective equipment such as insulation gloves, insulation shoes and goggles. Operating the battery pack without protection can cause a serious electric shock. 1. Start the iSmartEV P01 and click [Battery pack detection] on the main interface. 2. Select the vehicle brand or battery pack brand(You can find it quickly through the search bar in the upper right corner) 17 www.newsmartsafe.com iSmartEV P01 User Manual 3. Select the vehicle model and year. 4. Select the connection method of battery pack. Note: For cars that support fast charging port detection, the "Fast Charging port detection" interface will be displayed after the connection mode is selected as [Fast Charging port Detection]. See Chapter 6 for specific operation. A. On-Board Diagnostics(OBD) seat connection The battery pack of the vehicle was tested by connecting the iSmartEV BOX detection BOX to the OBD diagnosis seat of the vehicle through an OBD extension cable. 18 www.newsmartsafe.com iSmartEV P01 User Manual B. Connect special connectors for battery packs Connect the iSmartEV BOX detection BOX and the low-voltage signal communication interface of the battery pack respectively with the battery pack special connector to test the vehicle battery pack. C. Battery pack jumper connection. According to the wiring diagram prompted by the software, the jump-8 jumper is used to connect the iSmartEV BOX detection BOX and the low-voltage signal communication interface of the battery pack respectively to detect the battery pack of the vehicle. Note: The picture here is an example only. The connection mode varies with vehicle types. Please connect based on the wiring diagram prompted by the software. 19 www.newsmartsafe.com iSmartEV P01 User Manual 5. After the connection is complete, the device automatically reads and displays the detailed data of the battery pack. Users can determine the abnormal status of the battery pack based on the detection data. Description for screen buttons:

Main Interface Click to return to the main interface. Exit Report Refresh Function description:

Voltage Detection Temperature Detection Click to exit the current detection process. Click to view/save the detection report of battery pack. Click to refresh the current data of battery pack. Used to display the voltage parameters of each module in the battery pack, and mark the highest/lowest voltage monomer in the battery pack. Used to display the temperature parameters of each module and other components in the battery pack, and mark the highest/lowest temperature monomer in the battery pack. Battery Pack Used to detect the ECU information, overall state, fault 20 www.newsmartsafe.com iSmartEV P01 User Manual Information Fault Code Detection state and module data in the battery pack, which is to quickly for the maintenance personnel convenient determine the fault point. Used to read the fault code in the current battery pack BMS system. Actuation Test Used to test whether the execution components in the system can work properly. Special Functions Used to learn and match the components in the battery pack BMS system. Note: The specific special functions provided depend on the vehicle type. 21 www.newsmartsafe.com iSmartEV P01 User Manual 6. Quick Charging Port Detection The function module must be equipped with iSmartEV FC01 new energy vehicle battery pack detection gun (optional), and the battery pack can be quickly detected through the DC quick charging port of new energy vehicle, so as to help the maintenance personnel quickly determine the battery pack fault. 1. On the main interface, click [Quick Charging Port Detection] to enter the quick battery pack detection screen. Make preparations before testing according to the precautions prompted on the interface, and then click [Next]. 2. Operate as prompted on the screen, insert the detection gun into the DC quick charging port of the vehicle, and then click [Next]. 3. The system starts searching for the detection gun. 22 www.newsmartsafe.com iSmartEV P01 User Manual 4. Select the serial number of the current detection gun for connection. Note:

1) When testing again, the system will automatically connect the detection gun. 2) If you need to switch the detection gun, please close the previously connected device and search for the connection again. 5. After the test is complete, you can view the battery pack quick test report. Slide the screen to view more information. 23 www.newsmartsafe.com iSmartEV P01 User Manual 6. Click [Save] to save the quick test report on the host. 7. Click [Share] to generate the two-dimensional code, and scan the two-

dimensional code to share the report. 24 www.newsmartsafe.com iSmartEV P01 User Manual 7. Vehicle Detection This function is mainly used for vehicle detection. Users can use "intelligent detection" to quickly identify vehicle information and enter the system for vehicle detection, or manually select models and systems for detection. 7.1 Intelligent Detection Use "Intelligent detection" to quickly identify vehicle information and vehicle detection, without manual selection of vehicle type. Click [Vehicle Detection] -> [Intelligent Detection] on the main interface to enable the intelligent detection function of vehicles. Some models may not be able to identify the vehicle information through the intelligent detection function. In this case, the following dialog box will pop up for the user to scan or manually input the vehicle VIN code. 7.2 Manual Selection 1. Click [Vehicle Detection] on the main interface to enter the vehicle brand selection interface. 25 www.newsmartsafe.com iSmartEV P01 User Manual 2. Click the vehicle brand to be tested to enter the model version information interface (for example: BYD). Screen button description:

Vehicle models that can be tested Click to view the current vehicle models that can be tested Confirm Click to enter the next step 3. Select the model and year of the vehicle to be tested (for example: BYD 2018 E5 Travel version). Automatic selection Clicking this item will automatically identify the model, year and VIN code of the vehicle under test. After confirming the information, click [Correct] to go to the next step. Manual selection Click this item to manually select the model and year, and click [Confirm] to go to the next step. 26 www.newsmartsafe.com iSmartEV P01 User Manual 4. Select the test options you want to perform. Note: Different models will have different systems and common special functions, users can choose the required options for testing. 7.2.1 Quick test This feature is used to quickly detect the vehicle and output the vehicle health report directly (this will only be displayed if the vehicle testing software supports this function). On the screen for selecting test options, click "Quick Test". The system starts to scan each system for fault codes and displays specific scan results. Systems with fault codes are displayed on the screen in red font with the specific number of fault codes. The system without faults (green) is displayed as "Normal". Screen Button Description:

If there are too many fault codes, click this button to hide the fault codes of the current system so that you can view 27 www.newsmartsafe.com iSmartEV P01 User Manual the fault codes of other systems. To view details about the fault code, click Click to enter the system and choose to perform other functions. Please refer to Chapter 7.2.2 for details. Compare the results Click to select the report before maintenance. By comparing the test reports before and after maintenance, the maintenance technician can clearly understand whether the fault codes found before maintenance have been completely cleared after maintenance. Note: Before performing this function, please ensure that:

The pre-maintenance inspection report of the current test vehicle has been saved; and the Repairs have been carried out on the basis of inspection report before maintenance, and the code has been cleared. Otherwise there will be no difference between the reports before and after the maintenance. Click to save the current fault report as the detection report. Report 28 to select the report type from the drop-down list, Click then enter the details and click [OK]. Note: Diagnostic reports can be classified into pre-

and post-maintenance report, report, maintenance www.newsmartsafe.com iSmartEV P01 User Manual diagnostic scan (if no comparison is required, you can

"Diagnostic Scan"). The device has the report select comparison function, so you need to select a correct report type when saving reports. By comparison, maintenance technicians can clearly understand whether the fault codes found before diagnosis have been completely cleared after maintenance. Enter the name of tester and customer, and then click [OK]

to enter the report details view page. On the report details page, click [Save] to save the report. All test reports are stored in the "Main Interface" -> "Test Report" tab. Help Click to view the cause analysis of the fault code. Code clearing Click to clear all the fault codes. Note: For general models, please strictly follow the conventional sequence: read the fault code first, then clear the fault code, test run, read the fault code again for verification, repair the vehicle, clear the fault code, test run again to confirm that the fault code does not appear. 7.2.2 System selection Users can use this function to manually select the vehicle electronic control system for testing. On the screen for selecting test options, click "Select System" to enter the following page:

Select the electronic control system to be tested. The function selection page is 29 www.newsmartsafe.com iSmartEV P01 User Manual displayed. "ECM", for example. Note: The test menu may be different for different models. A. Version information This function is used to read the ECU version information of the current vehicle. B. Read fault code This function is used to read the fault code existing in the current car ECU, and help maintenance personnel quickly understand the cause of vehicle failure. Click [Read Fault Code] on the test function selection page, and the screen will display the following detection results. Warning: Reading a fault code while troubleshooting a vehicle is only a small step in the diagnostic process. The vehicle fault code is only used as a reference, and parts cannot be replaced directly on the basis of the given fault code definition. Each fault code has a set of test procedures, and the maintenance technician must strictly follow the operating instructions and procedures described in the vehicle maintenance manual to confirm the root of the fault. Screen button description:

30 www.newsmartsafe.com iSmartEV P01 User Manual Freeze frame If the button is highlighted, the frame is frozen. The freezing frame function is to record the values of some specific data streams at the moment when the car breaks down for verification. Help Click to view the possible cause of the fault code. Relevant search Click to search for a specific explanation of the fault code online. Report Save the current test result as a test report. All test reports are stored in the "Main Interface" -> "Test Report" tab. C. Clear fault code This function is used to clear fault codes stored in the ECU of the system under test. In the test function selection page, click [Clear fault code], the system will pop up a dialog box of confirming clearing, click [Yes] to confirm the clearing of the fault code. Note: For general models, please operate in strict accordance with the conventional sequence: read the fault code first, then clear the fault code in the test run, read the fault code again for verification, repair the vehicle, clear the fault code, and confirm the fault code does not appear in the test run again. D. Read data stream This function is mainly used to read and display the car ECU real-time operation data and parameters. By observing these real-time data streams, the mechanic can gain insight into the overall performance of the vehicle and provide guidance for vehicle maintenance. Danger:

If you must drive the vehicle while performing troubleshooting, please ask someone else to help you. Driving and operating diagnostic equipment at the same time is dangerous and can cause serious traffic accidents. Click [Read Data Stream] on the test function selection page, and the system enters the data stream selection page. 31 www.newsmartsafe.com iSmartEV P01 User Manual Screen button description:

Current page Select all data stream options on the current page. Select all Select all data stream options. Cancel selection Click to cancel all the selected data stream options. Confirm Confirm the current operation. Click [Confirm], the system will display the dynamic data of the selection. 32

www.newsmartsafe.com iSmartEV P01 User Manual Note:

, the following popup will 11. Click appear on the screen:

Users can set different display styles for each data stream option according to their personal preferences. means stick it on top. When you click on be it, highlighted

. In the data stream display screen, the data stream are displayed at options with the top of the list of data stream it will options. If you want to cancel the top, click the icon again. B Indicates that the current data stream will be displayed in bold. A Indicates that the current data stream will be displayed in red. 2. Click [Imperial System]/ [Metric System] to switch units. 3. If the read data stream value is out of the standard value range, the data stream is displayed in red. There are three display modes for data stream, and users can choose the appropriate way to browse:

[Graphics] : Display parameters in the form of waveforms.

[Value] : Default display mode. The parameters are displayed in the form of values and lists.

[Free combination] : The graphics are presented in a combination way for users to compare. Note: Different data stream options are marked with different colors. Screen button description:

33 www.newsmartsafe.com iSmartEV P01 User Manual Click to display the current (single) data stream as a waveform diagram.

(single graphic) Note: The waveform can be zoomed in or out. Tap the screen with two fingers (thumb and index finger, for example), then slide the fingers to adjust the distance between the fingers to zoom in and out of the screen. to set Click Limit:

Upper/Lower the maximum/minimum value. Once the running value exceeds the set value, the system will issue a warning. Click to select the data stream sample, and the values you set and saved in the process of data stream collection will be imported into the [Standard Range]

column for you to compare. Note: You must collect and save the values of the data stream option before performing this function. Used to collect data stream samples. After collecting, recording, and saving data streams, you can import data stream samples to cover the current data in the

"Standard Range" column each time you view the data stream options. Click this button to start recording, and the screen will display as follows:

Note: The system records only the data stream option with units. Standard Collect 34 www.newsmartsafe.com iSmartEV P01 User Manual to stop recording and the system will Click automatically jump to the page of value modification. Click the data stream option to modify the values in the

[Minimum Value] and [Maximum value] columns. After modification, click [Save] to save your customized data stream value as sample data stream. All sample data streams are saved in "Main Interface" -> "Test Report" -

> "Vehicle Detection". Displays the parameters of stream as a waveform diagram. the selected data Free combination: The graphics are presented in combination for users to compare. Select

(A maximum of four data streams can be selected) the data streams to be viewed. The corresponding waveform is displayed on the screen. To remove unnecessary options, cancel the selection. Numerical numerical and list form. value: Displays parameters in Click to save the current data stream value as a report. The saved test report is stored in "Main Interface" ->

"Test Report" -> "Vehicle Test". Click to start recording test data. The recorded test data can provide an important reference for technicians to troubleshoot vehicle problems. To stop reading, click in front of the progress bar. the button Note: The saved file is named after vehicle type

+VCI device serial number + system time when recording starts. To distinguish file names, please set 35 Graphic Report Recording www.newsmartsafe.com iSmartEV P01 User Manual the correct system time. E. Actuation test This function is mainly used to test whether the executive component in the electronic control system can work normally. 36 www.newsmartsafe.com iSmartEV P01 User Manual 8. Endoscope The function module needs to work with endoscope equipment (optional), which can perform HD endoscope operation to detect parts that are invisible or inaccessible to the vehicle. For detailed operation, please refer to the user manual that comes with the endoscope equipment. 9. Current Clamp The function module needs to work with the new energy current clamp

(optional), and can perform AC/DC current test and DC voltage test. For detailed operation, please refer to the user manual delivered with the new energy current clamp. 10. ADAS Calibration The ADAS calibration function is used to calibrate driver assistance systems with various cameras and radars, such as front-facing cameras for lane departure warning systems, and radar sensors for ACC (Adaptive Cruise Control), etc. 10.1 Activate ADAS calibration function The ADAS calibration function on the device is disabled by default. Users need to use the activation card to activate the function before using it. This function is available with the specified ADAS calibration tool (purchased separately). Perform the following steps to activate the device:

(1) Click [ADAS Calibration] on the main interface, and the following prompt box will pop up. Click [Activate] to enter the ADAS activation page.

(2) Click [Activate] on the ADAS activation page. 37 www.newsmartsafe.com iSmartEV P01 User Manual

(3) Scrape the coating area of the ADAS activation card to display the activation code. Enter the 24-digit activation code, and then click [Activate] to activate the ADAS function.

(4) After successful activation, the calibration function of ADAS can be used normally. 10.2 Start calibration Users need to perform the calibration as prompted on the host. The ADAS calibration function is introduced through the ADAS demo program as follows. Note: Before performing the ADAS calibration operation, make sure that the VCI connector is connected to the vehicle diagnosis seat and the Bluetooth communication between it and the host is normal. 10.2.1 ADAS system selection Use this function to select the ADAS system to be calibrated through ADAS. 38 www.newsmartsafe.com iSmartEV P01 User Manual 10.2.2 ADAS system scanning Use this function to scan which ADAS systems are installed on the test vehicle. The ADAS system supports two display modes: topology and list. Click [Start Scanning] to scan the ADAS system one by one. After the scan is complete, click the system displayed in red (the system is displayed in red, indicating that there is a fault code in the system) to view the fault code, and click the system that works normally (the system is displayed in green, indicating that the system works normally) to perform other diagnostic functions. 10.2.3 ADAS calibration function Users can use this option to perform ADAS calibration operations. To perform this function, please coordinate with a calibration tool such as ADAS Mobile or ADAS PRO+. The calibration tool is used to locate the calibration target, and the plate is used to guide the user on how to position the calibration function and provide detailed calibration steps. Click [ADAS calibration function] to enter the following page:

39 www.newsmartsafe.com iSmartEV P01 User Manual Click the item to be calibrated and then follow the instructions on the screen to perform the calibration function. After the calibration is complete, a prompt box will pop up on the screen asking whether to save the ADAS report. Click [Confirm] to save. All ADAS reports are stored under the "My Reports" ->

"ADAS Reports" tab. 10.2.4 Whole vehicle examination After the calibration of the ADAS system, use this option to perform a full vehicle scan to confirm that the vehicle fault code has been cleared. 40 www.newsmartsafe.com iSmartEV P01 User Manual 11. Special Functions This module provides the quick entry for commonly used special function operation, including A/F adjustment, brake pad replacement, maintenance lamp returns to zero, steering angle learning, battery replacement, ABS exhaust, throttle learning, tire pressure reset, DPF regeneration, wave case learning, gear learning, headlamp matching, electronic water pump start, engine power balance, anti-theft matching, high pressure accumulator health detection, GPF regeneration and release of transport mode etc. If you need to operate more special functions, you can enter the diagnostic model software to operate Note: The specific special functions provided depend on the vehicle type. 11.1 A/F Reset This function is applied to set or learn Air/Fuel ratio parameters. 11.2 Electronic Parking Brake Reset This function enables you to reset the brake pad after replacing the brake pad. It needs to be performed in the following cases:

1) The brake pad and brake pad wear sensor are replaced. 2) The brake pad indicator lamp is on. 3) The brake pad sensor circuit is short, which is recovered. 4) The servo motor is replaced. 11.3 Oil Reset Service If the service lamp is on, run car diagnostics first for troubleshooting. After that, reset the driving mileage or driving time, so as to turn off the service lamp and enable a new driving cycle. 11.4 Steering Angle Calibration This function enables you to reset the steering angle, after replacing the steering angle position sensor, replacing steering mechanical parts (such as steering gearbox, steering column, end tie rod, steering knuckle), performing four-wheel alignment, or recovering car body. 11.5 Battery Maintenance System Reset This function enables you to perform a resetting operation on the monitoring unit information will be in which the original of vehicle battery, cleared and battery matching will be done. low battery fault 41 www.newsmartsafe.com iSmartEV P01 User Manual It needs to be performed in the following cases:

1) The main battery is replaced. 2) The battery monitoring sensor is replaced.. 11.6 ABS Bleeding This function allows you to perform various bi-directional tests to check the operating conditions of Anti-lock Braking System (ABS). It needs to be performed in the following cases:

1) When the ABS contains air. 2) When the ABS computer, ABS pump, brake master cylinder, brake cylinder, brake line, or brake fluid is replaced. 11.7 Throttle learning This function enables you to make initial settings to throttle actuators and returns the learned values stored on ECU to the default state. Doing so can accurately control the actions of regulating throttle (or idle engine) to adjust the amount of air intake. Cases when throttle learning is required:

the replacement of the ECU does not store the the ECU, 1) After characteristics related to the working of the throttle, so the throttle matching is required. 2) After the power-off of the ECU, the memory of the ECU memory is lost, and throttle matching is required. 3) After replacing the throttle assembly, the throttle matching is required. 4) After the replacement or disassembly of the inlet, the coordination of the ECU and throttle body on the idle speed control will be affected, and the throttle matching is required. 5) After cleaning the throttle, the idle throttle potentiometer have not changed, but under the same throttle opening, the air intake has changed, and the idle control characteristics have changed. At this time, it is necessary to match the throttle. the characteristics of 11.8 Tire Pressure Monitor System Reset This function enables you to quickly look up the tire sensor IDs from the vehicles ECU, reset tire pressure and turn off the tire pressure MIL. It needs to be performed in the following cases:

Tire pressure is too low, tire leaks, tire pressure monitoring device is replaced or 42 www.newsmartsafe.com iSmartEV P01 User Manual installed, tire is replaced, tire pressure sensor is damaged, and tire is replaced for the car with tire pressure monitoring function. 11.9 Diesel Particulate Filter (DPF) regeneration This function enables you to clear PM (Particulate Matter) from the DPF through continuous combustion oxidation mode (such as high filter reduce PM temperature heating combustion, ignition combustion) to stabilize the filter performance. fuel additive or catalyst It needs to be performed in the following cases:

1) The exhaust back pressure sensor is replaced. 2) The PM trap is removed or replaced. 3) The fuel additive nozzle is removed or replaced. 4) The catalytic oxidizer is removed or replaced. 5) The DPF regeneration MIL is on and maintenance is performed. 6) The DPF regeneration control module is replaced. 11.10 Gearbox Matching This function enables you to complete the gearbox self-learning to improve gear shifting quality. It needs to be performed in the following cases:

When the gearbox is disassembled or repaired. 11.11 Gear Learning This function enables you to perform tooth learning for the car, to turn off the MIL. It needs to be performed in the following cases:

1) After the engine ECU, crankshaft position sensor, or crankshaft flywheel replaced. is 2) The DTC 'tooth not learned' is present. 11.12 Motor Angle Calibration Diagnosis When the rotor position detected by the motor angle position sensor is different from the actual rotor field position, motor angle calibration must be performed. 11.13 Coolant Bleed Use this function to activate the electronic water pump before venting the cooling system. 11.14 Engine Power Balance Monitoring Diagnosis 43 www.newsmartsafe.com iSmartEV P01 User Manual It is used to monitor crankshaft acceleration in the power stroke of each cylinder, to determine the relative power provided by each cylinder. 11.15 IMMO Service This function enables you to perform the anti-theft key matching function, so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car. It needs to be performed in the following cases:

When the ignition switch key, ignition switch, combined instrument panel, ECU, BCM, or remote control battery are replaced. 11.16 High Voltage Battery Diagnostics Diagnosis It is used for high voltage battery diagnosis and status information detection. 11.17 Gas Particulate Filter Regeneration Diagnosis After the GPF is used for a long time, fuel consumption is increased and engine output power is reduced. In this case, the GPF replacement or regeneration must be performed. 11.18 Transport Mode In order to reduce power consumption, the following functions may be disabled, including limiting the vehicle speed, not waking up the door opening network, and disabling the remote control key, etc. At this time, the transport mode needs to be deactivated to restore the vehicle to normal. 11.19 Tire Reset This function is used to set the size parameters of the modified or replaced tire. 11.20 Windows Calibration This feature is designed to perform door window matching to recover ECU initial memory, and recover the automatic ascending and descending function of power window. 11.21 AdBlue Reset After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required. 11.22 NOx Sensor Reset NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. If the NOx fault is re-initialized and the NOx catalytic converter is 44 www.newsmartsafe.com iSmartEV P01 User Manual replaced, it is necessary to reset the catalytic converter learned value stored in the engine ECU. 11.23 Injector Coding This function enables you to write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder, so as to more accurately control or correct cylinder injection quantity. It needs to be performed in the following cases:

After the ECU or injector is replaced. 11.24 Airbag Reset The function can reset airbag data and clear DTCs related to airbag collision;

when the vehicle collides and the airbags are deployed, a corresponding DTC of the collision data shall be generated and the airbag indicator will be on. The DTC cannot be cleared. Since the data in airbag ECU are one-off, its necessary to replace the accessories with new ones as required. However, the execution of this function can recover the data in airbag ECUs and clear the DTC. The airbag indicator will go out and the airbag ECUs can be used continually. 11.25 Stop/Start Reset This function is used to open or close the automatic start-stop function via setting the hidden function in ECU (provided that the vehicle has a hidden function and supported by hardware). 11.26 Sunroof Initialization This function enables you to set the sunroof lock off, closed when it rains, sliding

/ tilting sunroof memory function, temperature threshold outside the car etc. 11.27 Suspension Calibration This function enables you to adjust the height of the body. It needs to be performed in the following cases:

1) When replacing the body height sensor, or control module in the air suspension system. 2) When the vehicle height is incorrect. 11.28 Odometer Calibration Diagnosis Instrument panel mileage calibration is used to copy or rewrite mileages. That is, use the car diagnostic computer and data line to copy, write or rewrite chip data on the instrument panel to make the instrument panel display actual mileages. 45 www.newsmartsafe.com iSmartEV P01 User Manual Usually, when the vehicle speed sensor is damaged or the mileage is incorrect due to instrument panel faults, you must perform mileage calibration after maintenance. 11.29 Language Change This function is used to change the system language of control panel. the vehicle central 11.30 Intelligent Cruise Control System Diagnosis It is used for matching after the intelligent cruise control module is replaced or repaired. 11.31 AC System Relearn/Initialization Diagnosis AC system relearn/ initialization must be performed when the vehicle AC ECU or actuator is replaced or the ECU memory is lost. 11.32 Seats Calibration This function is applied to match the seats with memory function that are replaced and repaired. 11.33 AFS (Adaptive Front-lighting System) Reset This function can be used to initialize the adaptive headlamp system. The to turn on the headlamp adaptive headlamp system can decide whether automatically according to the environmental intensity, and monitor the light vehicle's speed and body posture, and adjust the lighting angle of the headlamp timely. 46 www.newsmartsafe.com iSmartEV P01 User Manual 12. Software upgrade When a new model is added or a new version of software is available, the system will prompt the user to upgrade. It is recommended that the user upgrade to the latest version in time. On the main interface, click [Software Upgrade] to enter the following page:

12.1 Upgradable Under the "Upgradable" tab, click [Select All] to select all upgradable software or select to start downloading, and enter the main interface after downloading. the software to be upgraded, click "One-click Upgrade"

Note: During the upgrade, ensure that the network connection is normal. If you need to upgrade a lot of software, it may take a long time

(depending on the network speed) please wait in patience. To cancel software. the selection of the software, click the check box in front of the 12.2 Downloaded Click the "Downloaded" tab, and the list shows the currently downloaded software. You can view the software version, installation package size, and software update content on this page. 47 www.newsmartsafe.com iSmartEV P01 User Manual 48 www.newsmartsafe.com iSmartEV P01 User Manual 13. Remote diagnosis The function module is used to remotely assist users in diagnosis operations. 13.1 Remote diagnosis request Tap [Remote Diagnosis] on the main interface to enter the remote diagnosis page. Note: Click the corresponding vehicle type software icon under the "Recent Diagnosis Record" tab to quickly initiate a remote assistance request. Click [Request selection interface. for Remote assistance]

to enter the vehicle type software Select the corresponding model software based on the car to be diagnosed (here we take "Demo Program" as the example). The following dialog box pops up on the screen. 49 www.newsmartsafe.com iSmartEV P01 User Manual Notify the maintenance technician to assist in remote diagnosis. You can take photos of the dialog box as shown above and share them with the technician. The technician can scan the two-dimensional code to log in the technician platform for remote diagnosis. You can also perform remote diagnosis according to the serial number of the detection connector provided by the user, the owner's mobile phone number or the license plate number. During the remote diagnosis, click the button or at the bottom of the screen to open a chat, so that users can communicate with technicians. Press and hold the button to record a voice, and release your finger to send it after recording. 13.2 Assist others remotely Click [Assist others remotely], the following interface will pop up:

50 www.newsmartsafe.com iSmartEV P01 User Manual Input the other party's product serial number, the owner's mobile phone number or the license plate number, and then click Start remote diagnosis to send a remote assistance request to the other party. The remote diagnosis can be started after the other party agrees. 13.3 Contact list On the remote diagnosis screen, tap the button in the upper right of the screen to enter the following screen:

51 www.newsmartsafe.com iSmartEV P01 User Manual the maintenance technician in the list Enter "friend user name/nickname/serial number" in the search bar to search for a friend and add the friend as a friend. The added friends will appear in the

"Contacts" list. Select the interactive page. In the interactive page, you can communicate with text and voice messages, send files and photos, invite remote assistance, etc. After the remote diagnosis is complete, the system automatically generates a diagnosis report, and users can view and send corresponding reports. The generated remote diagnostic reports are stored in [My Reports] -> [Remote Reports]. to enter 52 www.newsmartsafe.com iSmartEV P01 User Manual 14. Personal center 14.1 My connector This function is used to manage all the VCI detection connectors that have been bound to the device. If multiple VCI detection connectors are bound to the detection device, you can use this item to select the corresponding VCI detection connector. 14.2 Connector activation If the VCI detection connector is not activated during registration, use this option to complete activation. Enter the product serial number and activation code and click [Activate]. 14.3 Firmware fix Used to repair connectors/check gun firmware. Do not power off or switch interfaces during the upgrade. 53 www.newsmartsafe.com iSmartEV P01 User Manual 14.4 Personal information Used to set and manage personal information. 14.5 Diagnostic unit settings Used to switch between metric and imperial units. 14.6 Diagnostic software clearing Used to clean or hide infrequently used detection software. 54 www.newsmartsafe.com iSmartEV P01 User Manual Note: Deleting the detection software will completely delete the detection software from the device. If some detection software is not used for a long time or the memory space of the device is insufficient, you can delete it. To download the software again, choose "Main Interface" > "Software Upgrade" > "All Software" and download it. 14.7 About You can view the software version, service agreement, and privacy policy, and set the network connection mode for automatically downloading applications. 14.8 Exit the current account Click [Exit the current account] button to log out. 55 www.newsmartsafe.com iSmartEV P01 User Manual 15. Detection report This option is used to view and manage saved vehicle test reports and test records. On the home screen, tap "Test Report" to enter the following page:

If the test report is saved during the battery pack test, the report will be displayed on the "Battery Pack Test" tab. If the test report is saved during the detection of the matching test gun, the report will be displayed under the label of "Quick charging port detection";

If the test report is saved during the ADAS calibration process, it will be displayed under the label "ADAS Report";

If the diagnosis report is saved during remote diagnosis, the report will be displayed under the "Remote Report" tab. If the detection report, fault code report and data stream report are saved during the vehicle detection, the report will be displayed under the "Vehicle Detection" tab. Click a single report in the test report list to view the report details, print and share the report. Click [Edit] to delete the selected test report, modify the file name of the report and share the report. Click [Filter] to select the report type and enter the vehicle VIN number, car series, model or customer name to filter the report you need from the report list. If the detected data is recorded on the read data stream screen, the detected data is displayed in the "Data Stream Playback" tab. Click the test record to be played back to enter the following screen:

56 www.newsmartsafe.com iSmartEV P01 User Manual Select the data stream option, and then click [Confirm] to enter the playback page:

Screen button description:

Graphic Play back the selected data stream options graphically. Combination Play back the selected data stream options in a combined form. Numerical value Playback the selected data stream options numerically. Frame playback Play back the recorded data stream frame by frame. playback Automatic Automatic playback of the recorded data stream 57 www.newsmartsafe.com iSmartEV P01 User Manual 16. Other 16.1 Tablet setting This option is used to set the system and view device information. 16.1.1 Network and Internet To set the wireless network connection, please perform the following steps:

Note: The power consumption of the device increases after the WLAN is enabled. You are advised to turn off the WLAN when it is not in use to save power. 1. On the home screen, click [Other] -> [Tablet Settings] -> [Network and Internet] -> [WLAN]. 2. Tap or slide the WLAN switch on. The device automatically scans for available wireless networks. 3. Select the network you want to connect to:

If you choose an open network, you can connect directly to that network. If you choose an encrypted network, you will need to enter an access password before you can connect 4. If "Connected" is displayed, the connection is successful. 16.1.2 Bluetooth Used to set up Bluetooth communication connection. 1. On the home screen, click [Other] -> [Tablet Settings] -> [Connected Devices]. 2. Click [+ Pair with new device]. The host automatically scans for available devices. Select the device you want to connect to. The host and selected devices dialog box will appear. After confirming the correct pairing code, click [Pairing] on both the host and the device to complete the Bluetooth connection between the host and the device. 16.1.3 Applications and Announcement It is used to manage application permissions and view application notifications. 16.1.4 Battery Used to view the application power usage and enable the power saving mode of the device. 58 www.newsmartsafe.com iSmartEV P01 User Manual 16.1.5 Display Used to set and adjust device display parameters. 16.1.5.1 Brightness 1. On the main interface, click [Other] -> [Tablet Settings] -> [Display] ->

[Brightness]. 2. Drag the slider to adjust the brightness. In addition, users can also slide down the screen to bring up the system shortcut bar to adjust the screen brightness 16.1.5.2 Automatically adjust the brightness Automatically adjust the brightness Click or slide the [Auto Adjust Brightness] switch to open to enable the device to automatically adjust and optimize the display brightness of the device according to the ambient light conditions. 16.1.5.3 Wallpaper This option is used to set the wallpaper picture of the device. 16.1.5.4 Screen timeout This option is used to set the automatic screen-down time of the device. 1. On the main interface, click [Other] -> [Tablet Settings] -> [Display] -> [Screen Timeout]. 2. Select a screen timeout period. 16.1.5.5 Screen saver This option enables the screen saver function and sets the screen saver background. 16.1.5.6 Font size This option is used to set the font size displayed on the device screen. 16.1.6 Volume Used to set the device volume. 16.1.7 Storage It is used to manage application storage space and clear application data and caches. 16.1.8 Privacy It is used to manage device privacy rights. This includes the permission for an application to access device data, whether characters are displayed briefly 59 www.newsmartsafe.com iSmartEV P01 User Manual when entering a password, and whether notifications are displayed when the screen is locked. 16.1.9 Location information Used to manage applications' access to and use of device location information. 16.1.10 Security Used for security management such as device lock screen encryption, blocking/allowing the installation of applications from unknown sources. 16.1.11 System Used to set device system information, including setting of device language and input method, gesture, date and time parameters, backup, reset and multi-user access etc. 16.1.12 USB management Used to set the USB switch of the device. 1. After you select this option, set the USB switch status to ON. In this case, the USB Type-C port is only used for charging. 2. Deselect this option and set the USB switch status to OFF. In this case, the USB Type-A port on the device stops being used. The USB Type-C port can be used to charge the device and connect the computer to transfer files. 3. Connect the computer through the USB Type-C interface of the device, slide down the screen, [Charging the device through USB] will be displayed, click this option, the USB debugging window will pop up. Click the USB mode you want to use. Note: Keep the USB switch ON when the device uses Wi-Fi for wireless diagnosis. 16.2 Diagnostic feedback If an unsolvable problem or diagnostic software problem is encountered during diagnosis, the user can report the problem (the last 20 test records) back to us. 60 www.newsmartsafe.com iSmartEV P01 User Manual After receiving your feedback, we will follow up and deal with it in time, so as to improve our product quality and user experience. There are three available options:

feedback Diagnostic Displays a list of all models that have been tested. Diagnostic feedback history Click to view the progress of all submitted diagnostic feedback. Offline list Click to view the diagnostic feedback of upload failure due to network problems. Once the network is restored, the system will automatically upload the data to the server. Under the "Diagnosis feedback" tab, click the corresponding model or special function of the diagnosis record to enter. Click "Select File" to open the target folder, select the diagnostic log that needs feedback, and then select the corresponding diagnostic feedback problem type. Enter the fault description and contact information of the feedback person in the text box. Then click "Upload Log" to send it to us. After receiving your fault feedback, we will follow up your feedback report in time. Please pay attention to the progress and results of diagnosis feedback in

"Diagnosis Feedback History". 16.3 File management This module is the file and program manager. Users can access and create folders directly on the device without connecting to a computer. 61 www.newsmartsafe.com iSmartEV P01 User Manual 16.4 Remote control In case of equipment operation problems, you can use this module to request assistance from the other party. After you start Remote control (TeamViewer QuickSupport), QuickSupport will automatically assign your ID, and the screen displays as follows:

Send your ID to the other party. After the other party enters your TeamViewer, click "Remote Control" to remotely control your device. ID in 16.5 Browser This module can be used to browse the web. 16.6 System OTA upgrade This module is used to upgrade the system. After entering, click [Detection Version], the system starts to check whether the current version is the latest version. If the version is the latest, the system will latest

[The prompt version]. 62 www.newsmartsafe.com iSmartEV P01 User Manual Note: When performing OTA upgrades, ensure that the device has at least 70%

power and that no programs are running during the upgrade. 16.7 Photo album This feature can be used to take photos, videos and manage galleries (including screenshots). 16.8 Screen recording A simple-to-use, convenient and quick screen recording software. Support recording screen playback, GIF animation and sharing functions. 16.9 Player This module is used to play music and video files. 16.10 Mail This module is used to receive and send mail. 16.11 Photograph The module is used to take photos and record videos. 63 www.newsmartsafe.com iSmartEV P01 User Manual 17. Frequently Asked Questions 1. How to save electricity?

1) Close the screen when the device is not in use. 2) Shorten screen standby time. 3) Reduce the screen brightness. 4) Disable the WLAN connection if you do not need to use the WLAN. 2. Failed to communicate with vehicle ECU?

Please confirm:

1) Check whether the VCI connector is properly connected. 2) Whether the ignition switch of the vehicle is turned on. 3) If the above are confirmed to be normal, please send the vehicle type, year, model and VIN code to us through "Other" -> "Diagnosis feedback" module. 3. Unable to enter vehicle ECU system?

Please confirm:

1) Whether the test vehicle is equipped with this system. 2) Check whether the VCI connector is properly connected. 3) Whether the ignition switch of the vehicle is turned on. 4) If the above are confirmed to be normal, please send the vehicle type, year, model and VIN code to us through "Other" -> "Diagnosis feedback" module. 4. The detection connector is not energized when connected to the vehicle. Please confirm:

1) If the VCI connector is improperly connected, reconnect the connector. 2) Poor line contact of vehicle diagnosis seat. 3) The vehicle battery itself has a serious power deficit. 4) The detection connector is damaged. 1. How to reset the iSmartEV P01 tablet?

Please reset the device according to the following procedures:

1) On the home screen, tap [Other] -> [Tablet Settings] -> [Backup and Reset]

-> [Restore Factory Settings]. 2) Click [Restore Tablet Factory Settings]. 3) Click [Clear All] and wait for the system to recover until the tablet automatically 64 www.newsmartsafe.com iSmartEV P01 User Manual restarts Warning: Resetting the device will result in the loss of device data. Before using it, please ensure that important data has been backed up. 65 www.newsmartsafe.com iSmartEV P01 User Manual FCC Warnning Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. 66 www.newsmartsafe.com iSmartEV P01 User Manual Warranty This WARRANTY applies only to customers and dealers who have purchased SmartSafe products through normal procedures. Within one year from the date of delivery, SmartSafe Company shall guarantee the defects of its electronic products caused by materials or processes. Damage of the equipment or components caused by abuse, unauthorized modification, use for purposes other than the design of the product, or failure to operate in the way specified in the instruction shall not be covered by this warranty. Disclaimer The warranty mentioned above may supersede any other warranty. Order notification The replaceable parts and optional parts can be ordered directly from the suppliers authorized by SmartSafe. Please specify when ordering:

Quantity ordered Part number Part name Customer Service Center the warranty, SmartSafe offer free maintenance;

If the equipment needs to be repaired, please send the equipment to SmartSafe, together with the purchase invoice and problem description. If the equipment is the within the scope of equipment the warranty, SmartSafe will charge for maintenance and return freight. Address of SmartSafe Company 3310, Building 11, Tian 'an Yungu Industrial Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China. Postcode: 518110 is outside the scope of If Statement: The Company reserves the right to change the product design and specifications without prior notice. The appearance and color of the object may be different from that shown in the instruction manual. The object shall prevail. We have tried our best to make all the descriptions in the book accurate, but there are still some inaccuracies. If you have any doubt, please contact the distributor or after-sales service center. The company will not assume any consequences caused by misunderstanding. 67

SHENZHEN SMARTSAFE TECH CO., LTD. Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AYANEVP01 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type File Name

(Block Diagram, Schematics, Operational (Block Diagram.pdf, Schematics.pdf, Description, Software Security Description) Operational Description.pdf, Software Security Description.pdf) The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commissions public notice, we also request temporary confidential treatment of information accompanying this application as outlined below:

Exhibit Type File Name Sincerely, Signature: iu Heng pe printed name: Yu Hongbo Rev 11/20/07

SHENZHEN SMARTSAFE TECH CO., LTD. Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: August 18, 2022 SUBJECT: FCC Application for (FCC ID: 2AYANEVP01) To Whom It May Concern:

We, the undersigned, hereby authorize Mina Xu at Centre Testing International Group Co., Ltd / Building C, Hongwei Industrial Park Block 70, Bao'an District, Shenzhen, China on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Mina Xu at Centre Testing International Group Co., Ltd /

Building C, Hongwei Industrial Park Block 70, Bao'an District, Shenzhen, China on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Regards, oe Yt Hong he printed name: Yu Hongbo M:\Master Documents\TEMPLATES\POA Letter.doc

SHENZHEN SMARTSAFE TECH CO., LTD. Federal Communications Commission Date: 2022-08-18 Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 SUBJECT: FCC SDoC declaration for FCC ID: 2AYANEVP01 To Whom it may concern, We, as the grantee of this project, would like to declare that this device has been tested according to the FCC requirement and found compliant with the following standards: FCC Part 15 Subpart B. Product Name : New Energy Vehicle Detection Tool Brand Name : SmartSafe Model Name : iSmartEV P01 Testing Lab : Centre Testing International Group Co., Ltd Sincerely, Yi, Vang be Signature:

Company Name > SHENZHEN SMARTSAFE TECH CO., LTD. Name : Yu Hongbo Job Title : Vice Manager E-mail >: yuhongbo@newsmartsafe.com Tel. : =+86-755-89589932