User manual V1.0 Wi-Fi Smart Dimmer Switch
--------------1 - 3 Deu tsch -------------8-11 Fra nais ----------16 -19
-----24 -27 English ------ - - 4 - 7 Espaol ---- - -1 2 -15 Italiano-------20 -23 SONOFF TECHN OLOGIES CO., LTD. English Specifications Model Input Output D1 100-240VAC50/60Hz 100-240VAC50/60Hz Light Load Incandescent200W LED:150W Operating systems Android 4.1 & iO S 9.0 or higher Wi-Fi Material IEEE 802.11 b/g/n 2.4GHz PC Dimension 62x47x32.5mm Features D1 is a Wi-Fi smart dimmer switch that is used to adjust the light brightness and set various atmosphere for your room. You can remotely turn on/o light of your home anywhere, schedule it on/o , or share it with your family to control together. Remote Control Single/Countdown Voice Control Timing 1 SONOFF TECHN OLOGIES CO., LTD. English Share C ontrol Bri ghtness Adjust ment Scene Mode Sync Status LAN Control 2 SONOFF TECHN OLOGIES CO., LTD. English Buttons Functions On Off Short press for the low brightness, long press to turn down the brightness Short press for the medium brightness, long press to turn down the brightness Short press for the high er brightnes s, lo ng press to tu rn u p the brightnes s Short press for the high brightness, long press to turn up the brightness Long press for 5s until you hea r Bi Bi a nd relea se, then the rem ote controller is clea red su ccessfu lly. I f you need to u se, short press any button within 5 s a fter powering on a gain and you will hea r Bi, which indica tes the remote controller is pa ired su ccessfu lly. Long pres s for 5 s u ntil the conne cted light enters the breathing mode, which indicates the device enters qu ick pairing mode (Touch), then you can add the light on eWeLink APP. In quick pairing mode, you can short press any button on the remote controller to exit this mode. 3 SONOFF TECHN OLOGIES CO., LTD. English Factor y Reset Turn on a nd o 3 ti me s on re pe ate dl y or del ete the connected light on eWeLink APP until it enters breathing mode, then the device is reset successfully and enters quick pairing mode (Touch). D 1 Setting Delete Please reset the switch to factory defaults if you want to use other Wi-Fi networks, then reconnect the network. 4 FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Radiation Exposure Statement The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC ID: 2APN5D1 Shenzhen Sono Technologies Co., Ltd. Room 1001, 10F, Building 8, Lianhua Industrial Park, Lon gyuan Road,Longhua District, Shenzhen, GD, China https://sono .tech MADE IN CHINA