all | frequencies |
|
|
exhibits | applications |
---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
User Manual part1 | Users Manual | 3.87 MiB | ||||
1 2 |
|
User Manual part2 | Users Manual | 3.61 MiB | ||||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | External Photos | |||||||
1 2 | RF Exposure Info | |||||||
1 2 | RF Exposure Info | |||||||
1 2 | Internal Photos | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Test Report | |||||||
1 2 | Test Report | |||||||
1 2 | Test Report | |||||||
1 2 | Test Report | |||||||
1 2 | Test Setup Photos | |||||||
1 2 | RF Exposure Info | November 07 2014 | ||||||
1 2 | Test Report | November 07 2014 | ||||||
1 2 | Test Report | November 07 2014 |
1 2 | User Manual part1 | Users Manual | 3.87 MiB |
Copyright Statement is the registered trademark of Shenzhen Tenda Technology Co., Ltd. All the products and product names mentioned herein are the trademarks or registered trademarks of their respective holders. Copyright of the whole product as integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd. No part of this publication can be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the prior written permission of Shenzhen Tenda Technology Co., Ltd. If you would like to know more about our product information, please visit our website at http://www.tendacn.com.
Disclaimer Pictures, images and product specifications herein are for references only. To improve internal design, operational function, and/or reliability, Tenda reserves the right to make changes to the products described in this document without obligation to notify any person or organization of such revisions or changes. Tenda does not assume any liability that may occur due to the use or application of, the product or circuit layout(s) described herein. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information and recommendations in this document do not constitute the warranty of any kind, express or implied. Preface Thank you choosing Tenda! Please read this user guide before you start! This user guide instructs you to install and configure the router. This user guide uses the following formats to highlight special messages:
Note: This format is used to highlight information of importance or special interest. Ignoring this type of note may result in ineffective configurations, loss of data or damage to device. Tip: This format is used to highlight a procedure that will save time or resources. Knowledge Center: Description of fields on the device GUI. Technical Support Website: http://www.tendacn.com Telephone: (86 755) 2765 7180 Email: support@tenda.com.cn Table of Contents I Product Overview ............................................................................................. 4 1 Package Contents ............................................................................................ 4 2 Getting to know your router ............................................................................. 4 LEDs on Front Panel ....................................................................................... 4 Buttons & Interfaces on Back Panel .................................................................. 6 Label .............................................................................................................. 6 3 Position Your Router ....................................................................................... 7 II Quick Internet Setup ....................................................................................... 8 1 Getting Prepared ............................................................................................. 8 Hardware Install ................................................................................................ 9 3. Internet Setup .............................................................................................. 10 1) Configure PC ............................................................................................ 10 2) Configure Router ...................................................................................... 10 4 Verify Internet Connectivity ........................................................................... 14 5 Join Your Wireless Network ........................................................................... 16 Windows 7 .................................................................................................... 16 Windows XP ................................................................................................. 19 III Features & Configurations ........................................................................... 22 1 Status ........................................................................................................... 22 1.1 System Status .......................................................................................... 22 1.2 WAN Status ............................................................................................. 23 1.3 LAN Status ............................................................................................. 24 1.4 Wireless Status ........................................................................................ 24 1.5 Connection Status .................................................................................... 25 2 Network ....................................................................................................... 25 2.1. LAN Settings.......................................................................................... 25 2.2. WAN Settings ......................................................................................... 26 2.3 Port Mode ............................................................................................... 31 2.4 MAC Clone ............................................................................................. 32 2.5. DHCP .................................................................................................... 33 2.6 DHCP Client List ..................................................................................... 34 2.7 Static Assignment .................................................................................... 34 2.8 DHCP Server - Guest Network .................................................................. 36 3 Wireless Settings ........................................................................................... 38 3.1 Wireless-Basic ......................................................................................... 38 3.2 Guest Network ......................................................................................... 39 3.3 Security .................................................................................................. 41 3.4 Advanced ................................................................................................ 42 3.6 Wireless Extender .................................................................................... 44 3.5 Access Control ........................................................................................ 74 3.7 WPS Setup .............................................................................................. 78 3.8 Connection Status .................................................................................... 81 4 Advanced Applications .................................................................................. 81 4.1 Bandwidth Control ................................................................................... 81 4.3 DDNS ..................................................................................................... 84 4.1 Virtual Server .......................................................................................... 87 4.2 DMZ Host ............................................................................................... 89 4.4 UPnP ...................................................................................................... 90 4.6 Route Table ............................................................................................. 91 4.5 Static Route ............................................................................................ 91 5 Security ........................................................................................................ 96 5.1 MAC Filter .............................................................................................. 96 5.2 Client Filter ............................................................................................ 98 5.3 URL Filter .............................................................................................. 99 5.4 Remote Web Management ....................................................................... 101 6 Tools .......................................................................................................... 102 6.1 Logs ..................................................................................................... 102 6.2 Traffic Statistics .................................................................................... 103 6.3 Time ..................................................................................................... 105 6.4 Change Password ................................................................................... 106 6.5 Backup.................................................................................................. 108 6.6 Restore ................................................................................................. 109 6.7 Firmware Update ................................................................................... 110 6.9 Reboot .................................................................................................. 113 Appendix 1 Configure PC TCP/IP Settings ...................................................... 116 Windows 7 ..................................................................................................... 116 Windows XP .................................................................................................. 122 Appendix 2 Join Your Wireless Network .......................................................... 126 Join Your Wireless Network - Windows 7 ......................................................... 126 Appendix 3 Factory Default Settings ............................................................... 131 Appendix 4 FAQs ............................................................................................ 133 Appendix 5 Remove Wireless Network from Your PC ....................................... 135 Windows 7 ..................................................................................................... 135 Windows XP .................................................................................................. 136 Appendix 6 Safety and Emission Statement ...................................................... 139 I Product Overview 1 Package Contents Unpack the package. Your box should contain the following items:
If any of the parts are incorrect, missing, or damaged, contact your Tenda dealer. Keep the carton, including the original packing materials, in case you need to return the product for repair. 2 Getting to know your router LEDs on Front Panel Status Solid Description 5G wireless radio is on Blinking Data being transferred over 5G wireless network Off Solid 5G wireless radio is off 2.4G wireless radio is on Blinking Data being transferred over 2.4G wireless network Off Solid 2.4G wireless radio is off LAN port connected correctly Blinking LAN port is transferring data Off No link is detected on this port. Solid WAN port connected correctly Blinking WAN port is transferring data No link is detected on this port. Off Solid WPS is enabled Blinking Off Device is performing WPS authentication on a client device. WPS negotiation is completed is disabled or WPS authentication function Blinking System is functioning correctly. Solid/Off The unit is malfunctioning. LED 5GHz 2.4GHz LAN 1/2/3 WAN WPS SYS POWER Solid Off Indicates a proper connection to the power supply Power is not supplied to the router. Please check the power connection between the power outlet and router. Buttons & Interfaces on Back Panel 1WiFi: Wireless radio ON/OFF button. Pressing the WiFi On/Off button turns the wireless radios on and off. 2WPS/RST: Pressing it for over 7 seconds restores the device to factory default settings. For factory default parameters, see Appendix 3 Factory Default Settings. Pressing it for about 1 second enables WPS-PBC and the WPS LED blinks. You can use this button to quickly add a wireless device or computer to your wireless network. 3LAN (1/2/3): The local (LAN) Ethernet ports are for cabling the device to local computers, switches, etc. 4WAN: The Internet (WAN) Ethernet port is for cabling the router to a cable or DSL modem. 5PWR: The power port for connecting the router to power outlet. Label 1Default Login IP address. This IP address is to be used to access the routers settings through a web browser. If you change it, you have to open a new connection to the new IP address and log in again. 2MAC address. 3WPS pin code. 3 Position Your Router The operating distance or range of your wireless connection can vary significantly depending on the physical placement of your router. For best performance, place your router:
Near the center of the area where your computers, smart phones and other devices operate, and preferably within line of sight to your wireless devices. In an elevated location such as a high shelf, keeping the number of walls and ceilings between the router and your other devices such as computers and smart phones to a minimum. Away from electrical devices that are potential sources of interference, such as ceiling fans, home security systems, microwaves or PCs. Away from any large metal surfaces, such as a solid metal door or aluminum studs. Away from other materials such as glass, insulated walls, fish tanks, mirrors, brick, and concrete that can also affect your wireless signal. II Quick Internet Setup 1 Getting Prepared Before you start the installation process, you need to prepare the following:
Description Comes in the package Please use the power adapter that comes in the package. Using a power adapter with a different voltage rating than the one included with the router will cause damage to the router. Should have installed IE8 or higher browser You will need it to connect your PC to the router This is provided by your ISP Your Internet service provider (ISP) should have provided you with all of the information needed to connect to the Internet. If you cannot locate this information, ask your ISP to provide it. If your ISP uses a PPPoE Internet connection, you will need ISP login name and password. If you use a DHCP Internet connection, no information is needed. If your ISP gives you a fixed or static IP address for Internet connection, you will need to gather the following information:
1) IP Address 2) Subnet Mask 3) Gateway 4) DNS Server 5) Alternate DNS Server (Optional) Item Router Power Adapter PC Ethernet Cable Internet service Gather ISP Information 8 Hardware Install Note ------------------------------------------------------------------------------------
Before you start, make sure you can access the Internet by connecting the cable from the incoming Internet side to your PC.
Connect the Ethernet cable from the Internet side to WAN port of the router. Connect one of the LAN ports on the router to the RJ45 (NIC) port on your PC using an Ethernet cable. Connect the router to a surge protected power strip using the included power adapter. 9 Note -------------------------------------------------------------------------------------
Using a power adapter with a different voltage rating than the one included with the device will cause damage to the device.
3. Internet Setup 1) Configure PC If your computer is set to a static or fixed IP address (this is uncommon), change it to obtain an IP address automatically from the router. If you are unsure, see Appendix 1 Configure PC TCP/IP Settings. 2) Configure Router Step 1. Log in to Web manager. Launch a web browser, say, IE. In the address bar, input 192.168.0.1, and press "Enter". 10 The login window appears, and enter the login password. This router will automatically detect WAN connection status when you press the Enter key (This happens when you first time set up the router or when you restore the router to factory default settings). The following screen appears when your Internet connection type is detected. Click OK. 11 And the Quick Setup screen appears after you clicked the OK button. Tip----------------------------------------------------------------------------------------
1. If you are not using the PPPoE or Dynamic IP (DHCP) Internet connection type, click Advanced for more connection types. 2. The default Internet connection type is DHCP (Dynamic IP). 3. The router has a preset wireless security key of 12345678 but it is deactivated by factory default. However if you click the OK button on that page, the wireless security key of 12345678 will be activated automatically. 4. Here we use the WPA-PSK/AES for explanation. If you want to use other security mode and/or cipher type, see Security.
Step 2. Internet Setup & Wireless Security Setup A. Select Dynamic IP (DHCP) to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP information or user name and password. Dynamic IP (DHCP) & Wireless Security Setup 12 Select Dynamic IP (DHCP). The default wireless band is 2.4G and default wireless security key is 12345678. For better security key, please change the default security key
(Security key should be 8-63 characters). Click Save to save your settings. B. Select PPPoE if your ISP uses a PPPoE connection and gives you a PPPoE user name and a PPPoE password. PPPoE & Wireless Security Setup Select PPPoE. 13 Enter the ISP login name and password. The default wireless band is 2.4G and default wireless security key is 12345678. For better security key, please change the default security key
(Security key should be 8-63 characters). Click Save to save your settings. 4 Verify Internet Connectivity System will automatically enter the Status screen after you save the settings made on the Quick Setup screen. A. If the connection status displays "Connected" (as shown below), you are connected to the Internet. B. If connection status displays "Cable improperly connected!, the connection between the router and Internet fails. Make sure the cable from the incoming Internet side is properly connected to the router's WAN port. If nothing is wrong,
"Connecting" or "Connected" will be displayed. 14 If the connection status displays "Connecting and WAN IP address displays
"0.0.0.0", wait until the page updates five times. And if it still displays "Connecting try the following steps:
Make sure physical connections are correctly established. Make sure you can access the Internet on your PC without using the router. If your ISP uses a PPPoE Internet connection, make sure you entered the correct ISP login name and password. If the problem is still unsolved, see 2.4 MAC Clone. 15 5 Join Your Wireless Network Having finished above settings, you can search for the device's default wireless network (SSID) from your wireless devices (notebook, iPad, iPhone, etc.) to connect to it wirelessly. Tip----------------------------------------------------------------------------------------
1. The router's SSID is Tenda_XXXXXX by default. 2. To join your wireless network, the PC you use must have installed a wireless network adapter. If not, install one.
Windows 7 Click the icon on the notification area on the bottom right corner. Tip--------------------------------------------------------------------------------------
If you cannot find the icon, try disabling the wired network adapter or unplug the Ethernet cable from the wired network adapter of your PC and refresh your desktop. If the problem remains unsolved, see Join Your Wireless Network -
Windows 7.
16 Select the wireless network you wish to connect and click Connect. 17 If you see the screen below, you are connecting to the wireless network. Enter the security key and click OK. When you see Connected displayed next to the wireless network you selected, you have connected to the wireless network successfully. 18 Windows XP Right click My Network Places from your PC's desktop and select Properties. Right click Wireless Network Connection and select View Available Wireless Networks. Double click the wireless network you wish to connect. 19 20 Enter the security key and click Connect. When you see Connected displayed next to the wireless network you selected, you have connected to the wireless network successfully. 21 III Features & Configurations For more and advanced features, click Advanced on the home page. 1 Status 1.1 System Status Click Advanced on the home page and the Status screen appears. Here you can view the routers WAN status and system status as noted below:
IP Address/Subnet Mask/WAN Tip----------------------------------------------------------------------------------------
1. Connection Status: Displays the router's current WAN connection status:
Disconnected, Connecting, or Connected. For explanation of the 3 connection statuses, see 4 Verify Internet Connectivity. 2. subnet mask/Gateway/Primary DNS Server/Secondary DNS Server: This type of information appears only if the router successfully connects to Internet via a PPPoE or DHCP (dynamic IP) connection. However if you connect the router to Internet with static IP settings provided by your ISP, these fields will display the settings you entered whether the router successfully connects to the Internet or not. 3. secondary DNS server. If nothing appears in the secondary DNS server field, there is no available
22 1.2 WAN Status Click Status -> WAN Status to enter the WAN Status screen as seen below. 23 1.3 LAN Status Click Status -> LAN Status to enter the LAN Status screen as seen below. 1.4 Wireless Status Click Status -> Wireless Status to enter the Wireless Status screen as seen below. 24 1.5 Connection Status Click Status -> Connection Status to enter the Connection Status screen. 2 Network 2.1. LAN Settings Click Network -> LAN to enter the LAN configuration screen. Here you can configure the LAN IP address. This IP address is to be used to access the routers settings through a web browser. Configuration Procedures Change the IP address to the one you wish to use, for example, 25 192.168.10.1. Click Save to save your settings. Tip ---------------------------------------------------------------------------------------
1. Default IP address and subnet mask are respectively 192.168.0.1 and 255.255.255.0. 2. This router does not support VLSM. 3. Be sure to make a note of any changes you apply to this page. If you change the LAN IP address of the router, you have to open a new connection to the new IP address and log in again.
2.2. WAN Settings Click Network -> WAN to configure your Internet connection settings. Select your Internet connection type:
A. Select PPPoE if your ISP provides you with a PPPoE user name and a PPPoE password. B. Select Static IP if your ISP provides you with fixed or static IP address settings
(special deployment by ISP; this is rare). C. Select DHCP (Dynamic IP) if you can access the Internet simply by directly connecting your computer to an Internet-enabled ADSL/Cable modem without configuring any settings. PPPoE 26 Configuration Procedures:
Internet connection Type: Select PPPoE. ISP Username: Enter the ISP login name. ISP Password: Enter the ISP login password. Click Save to save your settings. Knowledge Center -----------------------------------------------------------------
1. MTU: The MTU (maximum transmission unit) is the largest data packet a network device transmits. The normal MTU value for most Ethernet networks is 1500 bytes, or 1492 bytes for PPPoE connections. For some ISPs, you might need to change the MTU. This is rarely required, and should not be done unless you are sure it is necessary for your ISP connection. For more information, see WAN MTU Setup. 27 Static IP Configuration Procedures:
Internet connection Type: Select Static IP. IP Address/Subnet Mask/WAN subnet mask/Gateway/Primary DNS Server/Secondary DNS Server: Enter those info which should be provided by your ISP. If you cannot locate this info, contact and consult your ISP. Click Save to save your settings. Dynamic IP (DHCP) 28 Configuration Procedures:
Internet connection Type: Select Dynamic IP (DHCP). Click Save to save your settings. WAN MTU Setup The MTU (maximum transmission unit) is the largest data packet a network device transmits. The normal MTU value for most Ethernet networks is 1500 bytes, or 1492 bytes for PPPoE connections. For some ISPs, you might need to change the MTU. This is rarely required, and should not be done unless you are sure it is necessary for your ISP connection. When one network device communicates across the Internet with another, the data packets travel through many devices along the way. If a device in the data path has a smaller MTU value than the other devices, the data packets have to be "fragmented" to accommodate the device with the smallest MTU value. The best MTU value for Tenda routers is often just the factory default value. In some situations, changing the MTU value fixes one problem but causes another. Leave the MTU unchanged unless one of these situations occurs:
29 A. You have problems connecting to your ISP or other Internet service, and the technical support of either your ISP or Tenda suggests changing the MTU value. Below web-based applications might require an MTU change:
A secure website that does not open, or displays only part of a web page Yahoo email MSN portal B. You use VPN and encounter serious performance problems. C. You used a program to optimize MTU for performance reasons, and now you have connectivity or performance problems. If you suspect an MTU problem, try changing the MTU to 1400. If this does not help, gradually reduce the MTU from the maximum value of 1500 until the problem disappears. The common MTU sizes and applications are listed in the table below. MTU 1500 1492 1472 1468 1436 Application Typical for connections that do not use PPPoE or VPN. Used in PPPoE environments. Maximum size to use for pinging. (Larger packets are fragmented.) Used in some DHCP environments. Used in PPTP environments or with VPN. Note -------------------------------------------------------------------------------------
A wrong/improper MTU value may cause Internet communication problems. For example, you may be unable to access certain websites, frames within websites, secure login pages, or FTP or POP servers.
30 2.3 Port Mode Click Network -> Port Mode to enter the WAN port mode screen. Here you can configure the router's WAN speed and duplex mode. Tip----------------------------------------------------------------------------------------
1. The best port mode is often just the factory default of "Auto". 2. In some situations, you might need to change the port mode. For example, if the cable connected to your router's WAN port is too long, you may need to use 10M full-duplex or 10M half-duplex for better performance.
31 2.4 MAC Clone Some ISPs (Internet Service Providers) require end-user's MAC address to access their network. This feature copies your current PC's MAC address to the router. Click Network -> MAC Clone to enter the MAC Clone screen. Knowledge Center ------------------------------------------------------------------
1. Restore Default MAC: Reset the routers WAN MAC to factory default. 2. Clone MAC: Clicking this button copies the MAC address of the computer that you are now using to the router. Also, you can manually enter the MAC address that you want to use. You have to use the computer whose MAC address is allowed by your ISP.
To restore default MAC address:
Click Restore Default MAC. Click Save to save your settings. To clone the MAC address of the computer that you are now using to the router:
32 Click Clone MAC. Click Save to save your settings. To manually enter the MAC address allowed by your ISP:
Enter the MAC address allowed by your ISP. Click Save to save your settings. 2.5. DHCP DHCP (Dynamic Host Configuration Protocol) assigns an IP address to each device on the LAN/private network. When you enable the DHCP Server, the DHCP Server will automatically allocate an unused IP address from the IP address pool specified in this screen to the requesting device as long as the device is set to "Obtain an IP Address Automatically". If you disable this feature, you have to manually configure the TCP/IP settings for all PCs on your LAN to access the Internet. Click Network -> DHCP Server to enter the DHCP Server screen. Here you can change the DHCP IP address pool and lease time. Configuration Procedures:
DHCP Server: Select whether to enable or disable the DHCP server feature. 33 Start IP/End IP: You can specify the starting and ending address of the IP address pool here. These addresses should be part of the same IP address subnet as the routers LAN IP address. Lease Time: The lease time is a time length that the IP address is assigned to each device before it is refreshed. Click Save to save your settings. Tip----------------------------------------------------------------------------------------
1. By default, the router enables DHCP server. Do not disable the DHCP server feature unless you want to manually configure the TCP/IP settings for all PCs on your LAN. 2. Lease time will be renewed automatically upon expiry. No additional configurations are needed. 3. recommended. If you are not an advanced user, the default DHCP server settings are
2.6 DHCP Client List Click Network -> DHCP Clients to enter the DHCP Clients screen. Here you can view the host name, IP address, MAC address, and lease time information. Tip ---------------------------------------------------------------------------------------
You can know whether there are unauthorized accesses by viewing the client list.
2.7 Static Assignment Click Network -> Static Assignment. Here you can specify a reserved IP address for a PC in the LAN. That PC will always receive the same IP address each time 34 when it accesses the DHCP server. Reserved IP addresses could be assigned to servers that require permanent IP settings. Static Assignment Application Example:
To make a PC at the MAC address of 44:37:E6:4F:37:3B always receive the same IP address of 192.168.0.123. Configuration Procedures:
Enter the IP address: 192.168.0.123. Enter the MAC address of 44:37:E6:4F:37:3B. Click Add. 35 Click Save to save your settings. Tip ---------------------------------------------------------------------------------------
1. If the IP address you have reserved for your PC is currently used by another client, then you will not be able to obtain a new IP address from the device's DHCP server, instead, you must manually specify a different IP address for your PC to access the Internet. 2. For PCs that has already obtained IP addresses, you may need to perform the Repair action to activate the configured static IP addresses.
2.8 DHCP Server - Guest Network Click Network -> DHCP - Guest Network to enter the guest network DHCP server screen. If you enable the built-in DHCP server for Guest Network on this device, it will automatically configure TCP/IP protocol settings for all DHCP-Client-enabled PCs on the Guest Network, including IP address, subnet mask, gateway and DNS etc. Configuration Procedures:
Click Enable. Start IP Address: Specify the start of the range for the pool of IP addresses in the same subnet as the device. 36 End IP Address: Specify the end of the range for the pool of IP addresses in a different subnet as the device. Click Save to save your settings. Click Network -> Client List - Guest Network to enter the guest network DHCP client list screen. This section displays a guest network DHCP dynamic client list, which includes host name, IP address, MAC address and lease time info. Refresh: Click to update the page. 37 3 Wireless Settings 3.1 Wireless-Basic Here you can configure the basic wireless settings of the router. Tip ---------------------------------------------------------------------------------------
If you are not an advanced user, it is advisable to only change the SSID (name of the network) and channel and leave other items unchanged.
Configuration Procedures:
Band: Select 2.4GHz or 5GHz. Primary SSID: This is the public name of your wireless network. Channel: Select a channel or select Auto to let system automatically select one for your wireless network to operate on if you are unsure. The best selection is a channel that is the least used by neighboring networks. Click Save to save your settings. Knowledge Center ------------------------------------------------------------------
1. 802.11 Mode (Network Mode): Select a correct mode according to your 38 wireless clients. 11b: This network mode delivers wireless speed up to 11Mbps and is only compatible with 11b wireless clients. 11g: This network mode delivers wireless speed up to 54Mbps and is only compatible with 11g wireless clients. 11b/g mixed: This network mode delivers wireless speed up to 54Mbps and is compatible with 11b/g wireless clients. 11b/g/n mixed: This network mode delivers wireless speed up to 300Mbps and is compatible with 11b/g/n wireless clients. 11ac This network mode delivers wireless speed up to 867Mbps. 2. SSID Broadcast: This option allows you to have your network names (SSIDs) publicly broadcast or if you choose to disable it, the SSIDs will be hidden. 3. Channel Bandwidth: Select a proper channel bandwidth to enhance wireless performance. This option is available only in 802.11b/g/n. Wireless speed in the channel bandwidth of 20/40 is 2 times in 20. 4. Extension Channel: This is used to ensure N speeds for 802.11n devices on the network. This option is available only in 11b/g/n mixed mode with channel bandwidth of 20/40.
3.2 Guest Network Click Wireless -> Guest Network to enter the Guest Network screen. The Guest Network feature allows guests to access the Internet and other users on the guest network while disallowing them to access Device web manager, users on master network and clients behind the LAN ports. Thus the wireless master network is secured. Configuration Procedures:
Band: Select 2.4GHz or 5GHz. Guest Network: Select whether to enable or disable the Guest Network feature. It is disabled by default. 39 Click Save to save your settings. 40 3.3 Security Click Wireless -> Security to enter the Security screen. Here you can define a security key to secure your wireless network against unauthorized accesses. To secure your wireless network Select a band, for example, 2.4GHz. Select the wireless network (SSID) you wish to encrypt. Select a security mode, cipher type configure a security key. Click Save to save your settings. Tip----------------------------------------------------------------------------------------
For better security, compatibility and wireless speed, we recommend the WPA-PSK and AES.
41 Knowledge Center ------------------------------------------------------------------
1. WEP: Wireless speed can reach up to 54Mbps if WEP - Open is selected. 2. Key Select: Select a key to be effective for the current WEP encryption. For example, if you select Key 1, wireless clients must join your wireless network using this Key 1. 4. WPA-PSK WPA personal, support AES and TKIP+AES cipher types. 5. WPA2-PSK WPA2 personal, support AES and TKIP+AES cipher types. 6. WPA/WPA2-PSK mixed: If selected, both WPA-PSK and WPA2-PSK secured wireless clients can join your wireless network. 7. AES: If selected, wireless speed can reach up to300Mbps. 8. TKIP: If selected, wireless speed can reach up to 54Mbps. 9. TKIP+AES: If selected, both AES and TKIP secured wireless clients can join your wireless network.
3.4 Advanced Click Wireless -> Advanced to configure the advanced wireless settings. This section allows you to configure advanced settings, including AP Isolation, Beacon interval, Fragment threshold, RTS threshold and DTIM interval, etc., for your wireless networks. Normally, the default settings will work. If not, change them according to the suggestions given by your ISP or Tenda technical staff. 42 Knowledge Center -----------------------------------------------------------------
1 AP Isolation: Isolates clients connecting to the primary SSID. 2 Beacon Interval: A time interval between any 2 consecutive Beacon packets sent by an Access Point to synchronize a wireless network. Do NOT change the default value of 100 unless necessary. 3 Fragment Threshold: Specify a Fragment Threshold value. Any wireless packet exceeding the preset value will be divided into several fragments before transmission. DO NOT change the default value of 2346 unless necessary. 4 RTS Threshold: If a packet exceeds such set value, RTS/CTS scheme will be used to reduce collisions. Set it to a smaller value provided that there are distant clients and interference. For normal SOHO, it is recommended to keep the default value unchanged; otherwise, device performance may be degraded. 5 DTIM Interval: A DTIM (Delivery Traffic Indication Message) Interval is a countdown informing clients of the next window for listening to broadcast and multicast messages. When the packets arrive in the routers buffer, the router will send DTIM (delivery traffic indication message) and DTIM interval to alert clients of the receiving packets. 43 3.6 Wireless Extender Use this wireless extender feature to extend your existing wireless network. 44 Click Wireless -> Wireless Extender to enter the following screen. This device provides three modes to extend your wireless network:
To extend your wireless network using the universal repeater feature, see Universal Repeater. To extend your wireless network using the WISP client router (wireless WAN) feature, see WISP Mode. To establish Wireless Distribution System and extend your wireless network, see WDS. Tip----------------------------------------------------------------------------------------
If "Disable" is selected, the wireless extender feature will be deactivated.
45 Universal Repeater Mode Universal Repeater: Use this universal repeater mode to extend your existing wireless network. The application scenario is shown in the figure below:
In this mode, you only need to configure the following settings on the Tenda wireless router:
Configure LAN IP: Specify an IP address that is in the same subnet as yet different from the remote wireless router for this Tenda wireless router. Universal Repeater: Configure this router to bridge the remote wireless router for extended network coverage. Tip --------------------------------------------------------------------------------------
46 Before you start, make sure you have the following information:
1. Remote router's SSID, security mode, cipher type and security key. 2. Remote router's LAN IP address. 3. No Ethernet cable is connected to this Tenda wireless router's WAN port.
Universal Repeater Application Example:
Assuming the remote wireless router has the following information:
SSID Tenda_0FF02D Security Mode: WPA-PSK Cipher Type: AES Security Key: 12345678 LAN IP Address: 192.168.0.1 Configuration Procedures:
Click Network -> LAN to configure an IP address that is in the same subnet as yet different from the remote wireless router for this Tenda wireless router. Click OK in the appearing screen. Select Universal Repeater and click Open Scan. 47 Select the remote router's wireless network (SSID) and click Close Scan. The SSID, channel, MAC address, security mode and cipher type of the remote router will be added automatically on this page. You only need to enter the security key and click Save. 48 Click Reboot to take configurations into effect. Note -------------------------------------------------------------------------------------
When the Universal Repeater is configured successfully, wireless clients can connect to this Tenda wireless router's SSID for Internet access.
Verify Bridge Connectivity:
Connect your PC to this Tenda wireless router via a wired or wireless connection and set it to "Obtain an IP address automatically". If you are not 49 clear, see Appendix 1 Configure PC TCP/IP Settings. Wait until your PC successfully obtains an IP address. Last number differs from that of the remote wireless router's LAN IP address. This is the remote router's LAN IP address. 50 Click Start -> Run. Enter cmd and click OK. Enter "ping default gateway IP address. Here in this example, enter "ping 192.168.0.1" and press Enter. If you see a similar screen, the bridge is established successfully. 51 WISP Client Router Mode WISP Mode: This is the WISP (Wireless Internet Service Provider) Client Router Mode. In this mode the router acquires Internet access from your WISP AP or a wireless Access Point on an existing network. Below shows the typical topology:
In this mode, you only need to configure the following settings on this Tenda wireless router:
WISP Mode Setup: This mode establishes a wireless connection between the wireless LAN interface of the remote wireless router and the wireless WAN interface of your Tenda wireless router. 52 Internet Setup: Configure this Tenda router to access the Internet. Tip---------------------------------------------------------------------------------------
Before you start, make sure you have the following information:
1. Configure IP address of the two linking routers into two different network segments. 1. Remote router's SSID, security mode, cipher type and security key. 2. Internet connection information provided by the remote wireless router. 3. No Ethernet cable is connected to the Tenda wireless router's WAN port.
WISP mode (Wireless WAN feature) Application Example:
Assuming the remote wireless router provides the following information:
SSID: Tenda_home Security Mode: WPA-PSK Cipher Type: AES Security Key: 12345678 LAN IP address: 192.168.0.1 Internet Connection Type (for client): DHCP (dynamic IP) Configuration Procedures:
53 Click Network -> WAN to configure the Internet connection. 54 Click Wireless -> Wireless Extender, select WISP Mode and click Open Scan. Select the remote router's wireless network (SSID) and click Close Scan. 55 The SSID, channel, MAC address, security mode and cipher type of the remote AP will be added automatically on this page. You only need to enter the security key and click Save. Click Reboot on the appearing screen to reboot the router. 56 System automatically enters the login window after reboot. Reaccess to the device. Click Status -> WAN Status to check the WAN status. 57 If the WAN Connection Status keeps displaying "Connecting....", change the LAN IP address of this router to a different subnet from the remote router's LAN IP address. Click OK on the appearing screen to reboot the router. 58 Click Reboot on the appearing screen to reboot the router. System automatically enters the Status screen after reboot. Check the WAN Connection Status, if it displays "Connected", you have successfully connected to Internet. 59 Note -------------------------------------------------------------------------------------
When the WISP (client router) mode is configured successfully, wireless clients can connect to this Tenda wireless router's SSID for Internet access.
Verify Bridge Connectivity:
Connect your PC to this Tenda wireless router via a wired or wireless connection and set it to "Obtain an IP address automatically". If you are not clear, see Appendix 1 Configure PC TCP/IP Settings. Wait until your PC successfully obtains an IP address. Last number differs from that of this Tenda router's LAN IP address. This is the LAN IP address of this Tenda router. 60 Click Start ->Run Enter cmd and click OK. 61 Enter "ping Tenda router's gateway IP address". Here in this example, enter "ping 192.168.1.1" and press Enter. If you see a similar screen
(highlighted area), the bridge is established successfully. WDS Mode WDS (Wireless Distribution System) includes Wireless Bridge and Wireless AP. The differences are described as below:
Operating in Wireless AP mode, clients can access the Internet by connecting to the router via an Ethernet cable or wirelessly. Operating in Wireless Bridge mode, clients can access the Internet by connecting to the router via an Ethernet cable or wirelessly joining the router's secondary SSID (wireless network) or guest network. WDS: Wireless distribution system (WDS) is a system enabling the wireless interconnection of access points in an IEEE 802.11 network. It allows a wireless network to be expanded using multiple access points without the traditional requirement for a wired backbone to link them. The Tenda wireless router can function as a base station AP to create a wireless network or as a repeater AP to repeat and extend the base station AP's wireless network to a farther and wider range. The following figure shows an application scenario. 62 In this mode, you must set up both the base station A and the repeater AP. Tip--------------------------------------------------------------------------------------
Before you start, verify the following:
1. Tenda wireless router 1 that functions as a base station AP has successfully connected to Internet. 2. No Ethernet cables are connected to the WAN ports of the repeater APs: Tenda wireless routers 2 and 3.
WDS Application Example (as shown in the application scenario above):
Step 1: Configure Base Station AP (Tenda Wireless Router 1) Mode: Select WDS Mode. WDS Mode: Select Wireless AP. SSID: Customize a SSID, for example, Tenda_home. 63 Channel: Specify a channel for the base station AP to operate on, for example, 2437MHz (Channel 6). Remote MAC Address: Manually enter the MAC addresses of the two remote repeater APs (You can click Open Scan to view the MAC addresses). Security Mode: Specify security mode/authentication type, cipher type and security key for the base station AP. Click Save to save your settings. Click Network -> DHCP Server on the base AP's configuration interface to enable the DHCP server. 64 Step 2: Configure Repeater AP (Tenda Wireless Router 2) Click Network -> LAN to specify a LAN IP address that is in the same subnet as yet different from the base station AP. Click OK in the appearing screen. Click Wireless -> Wireless Extender, select WDS Mode from the Mode 65 drop-down list, select Wireless AP from the WDS Mode drop-down list and then click Open Scan. Search for and select the base station AP's SSID and then click Close Scan. 66 The SSID, channel, MAC address, security settings except security key of the base station AP will be automatically added to the corresponding fields. You only need to enter the security key of the base station AP and click Save. 67 Click Network -> DHCP Server, disable the DHCP server there and then click Save. Step 3: Configure Repeater AP (Tenda Wireless Router 3) Click Network -> LAN to specify a LAN IP address that is in the same subnet as yet different from the base AP and the other remote AP. 68
1 2 | User Manual part2 | Users Manual | 3.61 MiB |
Click OK in the appearing screen. Click Wireless -> Wireless Extender, select WDS Mode from the Mode drop-down list, select Wireless AP from the WDS Mode drop-down list and then click Open Scan. Search for and select the base station AP's SSID and then click Close Scan. 69 The SSID, channel, MAC address, security settings except security key of the base station AP will be automatically added to the corresponding fields. You only need to enter the security key of the base station AP and click Save. Click Network -> DHCP Server, disable the DHCP server there and 70 then click Save. Note -------------------------------------------------------------------------------------
1 To set up a wireless network with WDS, both access points must be WDS capable. 2 This router's primary SSID will automatically change to match that of the remote router when the WDS feature is configured successfully. Please do not change this SSID. Changing this SSID may interrupt the wireless bridge link. 3 When the WDS is configured successfully, wireless clients can connect to this Tenda wireless router's SSID for Internet access.
Verify Bridge Connectivity:
Connect your PC to this Tenda wireless router via a wired or wireless connection and set it to "Obtain an IP address automatically". If you are not clear, see Appendix 1 Configure PC TCP/IP Setting. Wait until your PC successfully obtains an IP address. 71 Last number differs from that of the remote wireless router's LAN IP address. This is the remote router's LAN IP address. 72 Click Start ->Run Enter cmd and click OK. Enter "ping default gateway IP address". Here in this example, enter "ping 192.168.0.1" and press Enter. If you see a similar screen (highlighted area), the bridge is established successfully. 73 3.5 Access Control Specify a list of devices to "Permit" or "Forbid" a connection to your wireless network via the devices MAC Addresses. Click Wireless -> Wireless Access Control to enter the configuration screen. There are three options available: Disable, Deny Access to Wireless Network and Allow Access to Wireless Network. A. If you want to allow all wireless clients to join your wireless network, select Disable. B. If you want to allow ONLY the specified wireless clients to join your wireless 74 network, select Allow Access to Wireless Network. C. If you want to disallow ONLY the specified wireless clients to join your wireless network, select Deny Access to Wireless Network. Wireless Access Control Application Example:
To only allow your own notebook at the MAC address of C8:3A:35:C2:CA:E7 to join your wireless network (SSID Tenda_home) Configuration Procedures:
Select the wireless band you wish to use, for example 2.4Ghz. Click Enable. Select Allow Access to Wireless Network. Click Add. 75 Select or enter your wireless MAC address and click Save. Below screen will then appear. 76 Tip ---------------------------------------------------------------------------------------
1. Up to 16 wireless MAC addresses can be configured. 2. If you don't want to configure the complex wireless security settings and want to disallow others to join your wireless network, you can configure a wireless access control rule to allow only your own wireless device.
77 3.7 WPS Setup Click Wireless -> WPS to enter WPS screen. Wi-Fi Protected Setup makes it easy for home users who know little of wireless security to establish a secure wireless home network, as well as to add new devices to an existing network without entering long passphrases or configuring complicated settings. Simply enter a PIN code or press the software PBC button or hardware WPS button (if equipped) and a secure wireless connection can be established. A If your wireless network is not secured, you can use the WPS to quickly encrypt your wireless. B If your wireless network is secured with WPS, you can quickly join your wireless network with a WPS capable adapter (Only WPA2-PSK and Mixed WPA/WPA2-PSK are supported). You can use WPS PBC or WPS PIN to establish a secure connection. PBC: Establish WPS connection using the the software PBC button or hardware WPS button (if equipped). PIN: Establish WPS connection using the PIN code. To secure a wireless network with WPS Knowledge Center ------------------------------------------------------------------
1. Reset OOB: If clicked, the device's SSID and security mode will become unconfigured so that WPS can reconfigure the device's SSID, security settings. When the action of Reset OOB completes, the device's SSID will be restored to factory default, and security mode will be disabled (none).
78 You can use the following 4 methods to establish a WPS connection:
Method 1: Establish a WPS connection using PBC on the Web Manager:
Select a band, for example, 2.4GHz. Click Enable. Click Save to save your settings. Click Start PBC. The WPS LED on this router will keep blinking for 2 seconds. Within these 2 minutes, enable WPS/PBC on the wireless client to join your wireless network. Method 2: Establish a WPS connection using the hardware WPS button on the device:
Select a band, for example, 2.4GHz. Click Enable. Click Save to save your settings. Press and hold the WPS button on the back panel of this router for about 1-3 seconds and then release it. The WPS LED on this router will keep blinking for 2 seconds. Within these 2 minutes, enable WPS/PBC on the wireless client to join your wireless network. Method 3: Establish a WPS connection using the 8-digit PIN code from the wireless network adapter:
79 Select a band, for example, 2.4GHz. Click Enable. Select PIN and enter the 8-digit PIN code from the wireless network adapter. Click Save to save your settings. Click Start PIN. The WPS LED on this router will keep blinking for 2 seconds. Within these 2 minutes, enable WPS/PIN- Enrollee on the wireless client to join your wireless network. Method 4: Establish a WPS connection using the 8-digit PIN code from the device:
Select a band, for example, 2.4GHz. Click Enable. Select PIN. Click Save to save your settings. Click Start PIN. Enable WPS/PIN on your router and WPS/PIN- Enrollee on the wireless client, and then enter the 8-digit PIN code from your router to join your wireless network. To quickly join a secured wireless network with WPS If you have already secured your wireless network with WPS or WPA2-PSK or Mixed WPA/WPA2-PSK and you want to join your wireless network but you hate to enter or forget the security key, do as follows:
Method 1: Establish a WPS connection using the hardware WPS button on the router:
Check the WPS LED status on the router. It should display a solid light. Press and hold the WPS button on the back panel of this router for about 1-3 seconds and then release it. The WPS LED on this router will keep blinking for 2 seconds. Within these 2 minutes, enable WPS/PBC on the wireless client to join your wireless 80 network. Method 2: Establish a WPS connection using the 8-digit PIN code from the router:
Check the WPS LED status on the router. It should display a solid light. Enable WPS/PIN- Registrar on the wireless client and enter the 8-digit PIN code from your router to join your wireless network. Note -------------------------------------------------------------------------------------
To use the WPS security, the wireless client must be also WPS-capable.
3.8 Connection Status Click Wireless -> Connection Status. Here you can see a list of wireless devices connected to the router. Tip ---------------------------------------------------------------------------------------
You can know whether there are unauthorized accesses to your wireless network by viewing the wireless client list.
4 Advanced Applications 4.1 Bandwidth Control If there are multiple PCs behind your router competing for limited bandwidth resource, then you can use this feature to specify a reasonable amount of 81 bandwidth for each such PC, so that no one will be over stuffed or starved to death. Click Advanced -> Bandwidth Control to enter the bandwidth control screen. Tip ---------------------------------------------------------------------------------------
1. 1M=128KByte/s. 2. The volume of uplink traffic/downlink traffic should not be larger than that allowed on the router's WAN (Internet) port. You can ask your ISP to provide the volume of Internet traffic.
Bandwidth Control Application Example:
If you share a 4M-broadband service with your neighbor. He always downloads a large volume of data from Internet, which sharply frustrates your Internet surfing experience; you can use this feature to set limits for the volume of Internet traffic he can get. For example, you can split the 4M into two, so your neighbor can only use up to 2M Internet traffic and you can enjoy 2M. (Assuming the IP address of your neighbor's PC is 192.168.0.100. 2M=256KByte/s) Configuration Procedures:
Click Advanced -> Bandwidth Control. Click Add Bandwidth Control Rule. Enter 192.168.0.100 in the IP Range fields. Enter 32 in the Uplink Bandwidth field. Enter 256 in the Downlink Bandwidth field. Click Save to save your settings. 82 Click Reboot on the appearing screen to reboot the router. Reaccess the device and go to check the rule you just add. Also you can click Edit to edit the rule or Delete to delete the rule. You can also add more rules. 83 4.3 DDNS Dynamic DNS or DDNS is a term used for the updating in real time of Internet Domain Name System (DNS) name servers. We use a numeric IP address allocated by Internet Service Provider (ISP) to connect to Internet; the address may either be stable ("static"), or may change from one session on the Internet to the next
("dynamic"). However, a numeric address is inconvenient to remember; an address which changes unpredictably makes connection impossible. The DDNS provider allocates a static host name to the user; whenever the user is allocated a new IP address this is communicated to the DDNS provider by software running on a computer or network device at that address;
the provider distributes the association between the host name and the address to the Internet's DNS servers so that they may resolve DNS queries. Thus, uninterrupted access to devices and services whose numeric IP address may change is maintained. Click Advanced -> DDNS to enter the DDNS screen. Tip ---------------------------------------------------------------------------------------
1. To use the DDNS feature, you need to have an account with one of the Service Providers in the drop-down menu first. 2. This router supports 2 DDNS service providers: dyndns and no-ip.
DDNS Application Example:
84 If your ISP gave you a dynamic (changing) public IP address, you want to access your router remotely but you cannot predict what your router's WAN IP address will be, and the address can change frequently. In this case, you can use a commercial Dynamic DNS service. It lets you register your domain to their IP address and forwards traffic directed at your domain to your frequently changing IP address. If you obtain the following account from your dyndns.org service provider:
User Name: tenda Password: 123456 Domain Name: tenda.dyndns.org. And you want to use the PC at 218.88.93.33 to remotely access this router on port number 8090. Configuration Procedures:
DDNS Service: Select Enable. Service Provider: Select your DDNS service provider from the drop-down menu. Here in this example, select dyndns. User Name: Enter the DDNS user name registered with your DDNS service provider. Here in this example, enter tenda. Password: Enter the DDNS Password registered with your DDNS service 85 provider. Here in this example, enter 123456. Domain Name: Enter the DDNS domain name with your DDNS service provider. Here in this example, enter tenda.dyndns.org. Click Save to save your settings. Click Security -> Remote Web Management, enable the Remote Web Management feature, enter 8090 in the Port field, 218.88.93.33 in the IP Address field and then click Save to save your settings. Click Reboot on the appearing screen to reboot the router. Now you can access the router from the Internet by http://tenda.dyndns.org:8090 in your browser. entering 86 4.1 Virtual Server You want to share resources on your PC with your friends who are not in your LAN. But, by default, the router's firewall blocks inbound traffic from the Internet to your computers except replies to your outbound traffic. You can use the Virtual Server feature to create exceptions to this rule so that your friends can access these files from external networks. Click Advanced -> Virtual Server to enter the configuration screen. Application Example:
As shown in the diagram above, your PC (PC1: 192.168.0.100) connects to the router and runs a FTP server on port number 21. Your friend (PC3) wants to access the FTP server on your PC. Tip ---------------------------------------------------------------------------------------
1. Make sure your WAN IP address (Internet IP address) is a public IP address. Private IP addresses are not routed on the Internet. 2. Make sure you enter correct service port numbers. 3. To ensure that your server computer always has the same IP address, assign a static IP address to your PC. 4. Operating System built-in firewall and some anti-virus programs may block other PCs from accessing resources on your PC. So it is advisable to disable them before using this feature.
87 Configuration Procedures:
Ext Port: Enter the external port number for the public ports at the Internet interface. Here in this example, enter 21. Int Port: Enter the internal port number for the private ports at the computer on the routers local area network (LAN). Here in this example, enter 21. Internal IP: Enter the IP address of your local computer that will provide this service. Here in this example, enter 192.168.0.100. Protocol: Specify the protocol required for the service utilizing the port(s). Check Enable to activate this rule. Click Save to save your settings. Now, your friends only need to enter ftp://xxx.xxx.xxx.xxx:21in their browsers to access your FTP server. xxx.xxx.xxx.xxx is the router's WAN IP address. Assuming it is 172.16.102.89, then your friends need to enter ftp://202.33.56.88:21 in their browsers. 88 Note
If you use the port number 80 here, you must set the port number for remote web management (Click Tools -> Remote Web Management) to any port number excluding 80 to avoid collision. Otherwise the port forwarding feature may not be effective.
4.2 DMZ Host The DMZ (De-Militarized Zone) function disables the firewall on the router for one device for a special purpose service such as Internet gaming or video conferencing applications that are not compatible with NAT (Network Address Translation). Click Advanced -> DMZ Host to enter the DMZ Host screen. Note
1. DMZ host poses a security risk. A computer configured as the DMZ host loses much of the protection of the firewall and becomes vulnerable to attacks from external networks. 2. Hackers may use the DMZ host computer to attack other computers on your network.
Configuration Procedures:
Enable: Check to enable the DMZ host. 89 DMZ Host IP Address: The IP Address of the device for which the routers firewall will be disabled. Be sure to statically set the IP Address of that device for this function to be consistent. Click Save to save your settings. Tip
1. Be sure to statically set the IP Address of the computer that serves as a DMZ host for this function to be consistent. 2. Security softwares such as anti-virus software and OS built-in firewall, etc may affect the DMZ host feature. Disable them if DMZ host fails.
4.4 UPnP The Universal Plug and Play (UPnP) feature allows network devices, such as computers from Internet, to access resources on local host or devices as needed. UPnP-enabled devices can be discovered automatically by the UPnP service application on the LAN. If you use applications such as multiplayer gaming, peer-to-peer connections, real-time communications such as instant messaging, or remote assistance (a feature in Windows XP), you may need to enable Universal Plug and Play (UPnP) for better experience. Click Advanced -> UPnP to enter the UPnP screen. The UPnP feature is enabled by default. 90 4.6 Route Table Click Advanced -> Route Table to view the router's route table. Knowledge Center ------------------------------------------------------------------
1.Destination Network: The IP address of the final destination. "0.0.0.0"
indicates any network segment. 2. Subnet Mask: The subnet mask for the specified destination. 3. Gateway: This is the next router on the same LAN segment as the router to reach. 4. Metric: This stands for the number of routers between your network and the destination. 5. Interface: The interface between your router and the final destination.
4.5 Static Route Static routes provide additional routing information to your router. Typically, you do not need to add static routes. However, when there are several routers in the network, you may want to set up static routing. Static routing determines the path of the data in your network. You can use this feature to allow users on different IP domains to access the Internet via this device. It is not recommended to use this 91 setting unless you are familiar with static routing. In most cases, dynamic routing is recommended, because this feature allows the router to detect the physical changes of the network layout automatically. If you want to use static routing, make sure the routers DHCP function is disabled. Click Advanced -> Static Routing to enter the configuration screen. Tip
1. Gateway must be on the same IP segment as WAN or LAN segment as the router. 2. Subnet Mask must be entered 255.255.255.255 if destination IP address is a single host.
Static Route Application Example - Gateway IP address on the same IP segment as WAN IP:
For example, your company internal network and Internet are on different IP net segment and you want PCs on your LAN to access the Internet and your company internal network via the Tenda Router. You can simply configuring static routes on the Tenda Router. The figure above depicts this application scenario. Configuration Procedures:
Click Add Static Route. 92 Destination Network: The IP address of the final destination. Enter your corporate internal network IP address: 172.16.100.0. Subnet Mask: Enter the subnet mask of your corporate internal network: 255.255.255.0. Gateway: Enter the gateway IP address to your corporate internal network: 192.168.30.88 Interface: Select WAN. Click Save to save your settings. Click Advanced -> Routing Table to view your static route entry. If it does not display, go to Tools to reboot your router. Enter the router's management interface. When the router successfully connects to the Internet, the following screen will display:
93 Static Route Application Example - Gateway IP address on the same IP segment as LAN IP:
As seen in the above figure, PC2 on LAN2 connects with the Tenda Router via the Router; PC1 on LAN1 accesses Internet via the Tenda Router that performs NAT. You can configure static routes to implement mutual communication between PCs 94 on LAN1 and LAN2. Configuration Procedures:
Click Add Static Route. Destination Network: Enter 192.168.50.0. Subnet Mask: Enter 255.255.255.0. Gateway: Enter 192.168.0.101 Click Save to save your settings. Click Advanced -> Routing Table to view your static route entry. If it does not display, go to Tools to reboot your router. Enter the router's management interface. When the router successfully connects to the Internet, the following screen will display:
95 5 Security This router provides three security policies: MAC filter, client filter and URL filter. To restrict your LAN PCs to access the Internet via their MAC addresses, see MAC Filter. To restrict your LAN PCs to access certain services on Internet via their IP addresses, see Client Filter. To restrict your LAN PCs to access certain websites on Internet via URL, see URL Filter. 5.1 MAC Filter This section allows you to restrict specific clients to access the Internet via the devices MAC addresses. Each PC has at least an installed network adapter with a unique MAC address. Three options are available: Disable, Deny and Allow. A. Disable: Disable the MAC Filter feature. B. Deny: Disallow only the devices at specific MAC addresses to access the Internet during the specific time period and/or specific days of the week. Access to Internet during other time period and/or other days of the week are not restricted. C. Allow: Allow only the specified devices to access the Internet during the 96 specific time period and/or specific days of the week. Access to Internet during other time period and/or other days of the week are denied. Click Security -> MAC Filter to enter the configuration screen. MAC Filter Application Example:
To allow only the PC at the MAC address of 00:C8:08:F5:E6:06 to access the Internet from Friday to Sunday (18:30-22:30). Configuration Procedures:
Filter Mode: Select Allow. Select: Select a rule ID, for example, (1). Enable: Check to enable this feature. Description: Briefly describe the current rule. This field is optional. Or if you want to enter it, then enter numbers, letters or underscore only. MAC Address: Specify the MAC address of the computer that you want to restrict, 00:C8:08:F5:E6:06. Time: Specify a time period for the current rule to take effect. Here in this example, select 18:30-22:30.Day: Select a day, or several days of the week for the current rule to take effect. Here in this example, select Friday, Saturday and Sunday. Click Save to save your settings. 97 5.2 Client Filter This section allows you to set the times specific clients can or cannot access the Internet via the devices assigned IP addresses and service port. Three options are available: Disable, Deny and Allow. A. Disable: Disable the Filter feature. B. Deny: Disallow only the devices at specific IP addresses to access certain services on Internet during the specific time period and/or specific days of the week. Other time period and/or other days of the week are not restricted. C. Allow: Allow only the devices at specific IP addresses to access specific services on Internet during the specific time period and/or specific days of the week. Access to any other services during other time period and/or other days of the week are denied. Click Security -> Client Filter to enter the configuration screen. Client Filter Application Example:
To prohibit PCs within the IP address range of 192.168.0.100--192.168.0.120 from accessing web pages during the time period of 8:00~18:00 from Monday to Frida 98 Configuration Procedures:
Filter Mode: Select Deny. Select: Select a rule ID, for example, (1). Enable: Check to enable this feature. Description: Briefly describe the current rule. This field is optional. Or if you want to enter it, then enter numbers, letters or underscore only, for example, 80. Start IP: Enter a starting IP address. Here in this example, enter 192.168.0.100.End IP: Enter an ending IP address. Here in this example, enter 192.168.0.120. Port: Enter a service port number. Here in this example, enter 80. Traffic Type: Select Both. Time: Specify a time period for the current rule to take effect. Here in this example, select 8:00~18:00.Day: Select a day, or several days of the week for the current rule to take effect. Here in this example, select Mon, Tue, Wed, Thur and Fri. Click Save to save your settings. 5.3 URL Filter To better control LAN PCs, you can use the URL filter functionality to allow or disallow such PCs to access certain websites within a specific time period and/or specific days of the week. Three options are available: Disable, Deny and Allow. A. Disable: Disable the URL Filter feature. B. Deny: Disallow only the devices at specific IP addresses to access certain services on Internet during the specific time period and/or specific days of the week. Other time period and/or other days of the week are not restricted. C. Allow: Allow only the devices at specific IP addresses to access specific services on Internet during the specific time period and/or specific days of the week. Access to any other services during other time period and/or other days of the week are denied. 99 Click Security -> URL Filter to enter the configuration screen. URL Filter Application Example:
If you want to disallow all computers on your LAN to access yahoo.com from 8 00 to 18 00 during working days: Monday- Friday, then do as follows:
Filter Mode: Select Deny. Enable: Check to enable this feature. Select: Select a rule ID, for example, (1). Description: Briefly describe the current rule, say, yahoo, (It can only consist of numbers, letters, or underscore). This field is optional. Start IP/End IP: Enter 2-254. URL String: Enter yahoo. Time: Specify a time period for the current rule to take effect. Here in this example, select 8:00~18:00.Day: Select a day, or several days of the week for the current rule to take effect. Here in this example, select Mon, Tue, Wed, Thur and Fri. Click Save to save your settings. Note -------------------------------------------------------------------------------------
Each entry can include up to 16 URL keywords, each of which must be 100 separated by ", ". 5.4 Remote Web Management The Remote management allows the device to be configured and managed remotely from the Internet via a web browser. Click Security -> Remote Web Management to enter the configuration screen. Tip ---------------------------------------------------------------------------------------
1 For better security, customize a port number between 1024-65535 for the remote web management interface, do not use the number of any common service port
(1-1024). 2. Make sure your WAN IP address (Internet IP address) is a public IP address. Private IP addresses are not routed on the Internet. 3. It is unsafe to make your router remotely accessible to all PCs on external network. For better security, we suggest that only enter the IP address of the PC for remote management.
Remote Web Management Application Example:
To access your router (WAN IP address: 102.33.66.88) at your home from the PC
(218.88.93.33) at your office via the port number 8080 Configuration Procedures:
Check "Enable". Enter 8080. Enter 218.88.93.33. Click Save to save your settings. Type http://102.33.66.88:8080 into your browsers address or location field and 101 you can access the router at your home remotely. Knowledge Center ------------------------------------------------------------------
1. Port: This is the management port to be open to outside access. The default setting is 8080. This can be changed. 2. IP Address: Here you can specify the IP address for remote management
(When set to 0.0.0.0, the device becomes remotely accessible to all the PCs on Internet or other external networks).
6 Tools 6.1 Logs Click Tools -> Logs to enter the logs screen. The Logs option allows you to view all events that occur upon system startup. View Log Levels: There are three types of logs available. 102 Here you can view the history of the devices actions. Up to 150 entries can be logged. After 150 entries, you can click Refresh to update the logs or click Clear to clear the earliest logs. 6.2 Traffic Statistics Click Tools -> Traffic Statistics to enter the Traffic Statistics screen. Traffic Statistics meter allows you to monitor and view the volume of traffic used by LAN devices. Tip ---------------------------------------------------------------------------------------
If you suspect some PCs behind your router are consuming a large volume of bandwidth (downloading videos, etc.) you can enable this Traffic Statistics meter feature to find out which PCs are overusing the traffic. Enabling the Traffic Statistics feature may degrade the routers performance. Do not enable it unless necessary.
Configuration Procedures:
Check Enable Traffic Statistics. 103 Click Save to save your settings. Click Reboot on the appearing screen to reboot the router. The following screen appears after reboot. 104 Knowledge Center ------------------------------------------------------------------
1. IP Address: Displays the IP addresses of the PCs that have connected to the device. 2. Uplink Rate: Displays the upload speed (KByte/s) of a corresponding PC. 3. Downlink Rate: Displays the download speed (KByte/s) of a corresponding PC. 4. TX Bytes: The number of bytes transmitted by a corresponding PC upon traffic statistics meter startup. The unit is M. 5. RX Bytes: The number of bytes received by a corresponding PC upon traffic statistics meter startup. The unit is M. 6. Connections: The number of clients that connect to this router.
6.3 Time Click Tools -> Time to enter the time screen. A. Sync with Internet time servers Note that the GMT time is obtained only when Device is connected to Internet. You can also configure the system time manually. Configuration Procedures:
105 Select your time zone. Click Save to save your settings. B. Set Time and Date Manually/Sync with Your PC Configuration Procedures:
Specify the time and date manually or click the Sync with Your PC to automatically copy your PC's time to the device. Click Save to save your settings. 6.4 Change Password Click Tools -> Change Password to enter the configuration screen. Here you can change the login password. It is strongly recommended that you change the factory default login password. Otherwise, anyone in your network can access this utility to change your settings. For example, if you want to change the login password to "tenda", do as follows:
Configuration Procedures:
106 Old Password: Input the old login password. New Password: Input a new password. Here in this example, enter "qpcom". Confirm New Password: Re-enter the new password for confirmation. Here in this example, enter "qpcom". Click Save to save your settings. Click OK on the appearing window. System will automatically enter the login window if you click OK. Enter the new login password of tenda and click Login to enter the devices configuration interface. 107 6.5 Backup Backup: Once you have configured the device the way you want it, you can save these settings to a configuration file on your local hard drive that can later be imported to your device in case that the device is restored to factory default settings. Click Tools -> Backup to enter the configuration screen. Tip ---------------------------------------------------------------------------------------
The default configuration file name is "RouterCfm.cfg". Do include the file name suffix of ".cfg" when renaming the file name to avoid problems.
Configuration Procedures:
Click Backup. Click OK on the appearing window. Click Save on the File Download window. 108 Select a local hard drive to save the file and click Save. 6.6 Restore Click Tools -> Restore to enter the configuration screen. Configuration Procedures:
Click Browse. 109 Select the configuration file that is saved previously to your local hard drive and click Open. Click the Restore button to reset your device to previous settings. 6.7 Firmware Update Click Tools -> Firmware Update to enter the configuration screen. Firmware upgrade is released periodically to improve the functionality of your device and also to add new features. If you run into a problem with a specific feature of the device, log on to our website (www.tendacn.com) to download the latest firmware to update your device. When upgrade is complete, the device restarts automatically. 110 Update takes a few minutes. Please wait. If you run into a problem with a specific feature of the device, log on to our website (www.tendacn.com) to download the latest firmware to update your device. Note -------------------------------------------------------------------------------------
1 Before you upgrade the firmware, make sure you are having a correct firmware. A wrong firmware may damage the device. 2. Do NOT upgrade the firmware wirelessly or disconnect device from power supply while firmware update is in process. Note that you need to update the device's firmware via a wired connection. Configuration Procedures:
Click Browse. Select the upgrade file and click Open. Click Upgrade (or Update). 111 Click OK on the appearing window. An upgrade progress indicator bar appears during the upgrade process. When upgrade is complete, the device restarts automatically. 6.8. Restore to Factory Default Settings Click Tools -> Restore to Factory Default to enter the configuration screen. Here you can reset the device to factory default settings. Note ------------------------------------------------------------------------------------
1. If you enable this option, all current settings will be deleted and be restored to factory default values. You will have to reconfigure Internet connection settings and wireless settings. 2. Do not restore factory default settings unless the following happens:
112 You need to join a different network or unfortunately forget the login password. You cannot access the Internet and Tenda technical staff asks you to reset the router. Click the Restore Factory Default button to reset the device to factory default settings. Default IP Address: 192.168.0.1 Default Subnet Mask: 255.255.255.0 6.9 Reboot Click Tools -> Reboot to enter the configuration screen. This section allows you to reboot the device. Click Reboot. 113 114 Click OK on the appearing screen below:
The router restarts automatically if the OK button is clicked. 115 Appendix 1 Configure PC TCP/IP Settings Windows 7 Click Start -> Control Panel. 116 Click Network and Internet. Click Network and Sharing Center. 117 Click Change adapter settings. Click Local Area Connection and select Properties. 118 Select Internet Protocol Version 4 (TCP/IPv4) and click Properties. 119 Select Obtain an IP address automatically and click OK. 120 Click OK on the Local Area Connection Properties window to save your settings. 121 Windows XP Right-click My Network Places and select Properties. Right click Local Area Connection and select Properties. 122 Select Internet Protocol Version 4 (TCP/IPv4) and click Properties. 123 Select Obtain an IP address automatically and click OK. 124 Click OK on the Local Area Connection Properties window to save your settings. 125 Appendix 2 Join Your Wireless Network Tip -------------------------------------------------------------
To join your wireless network, the PC you use must have an installed wireless network adapter. If not, install one.
Join Your Wireless Network - Windows 7 Click Start -> Control Panel. 126 Click Network and Internet. Click Network and Sharing Center. 127 Click Change adapter settings. Right Connect/Disconnect. click the Wireless Network Connection and select Select the wireless network you wish to connect and click Connect. 128 Depending on whether you are joining a secured or unsecured wireless network, you will see different screens:
A. If you are joining an unsecured wireless network as seen below:
B. If you are joining a secured wireless network as seen below:
129 You are required to enter a security on the following screen. Enter the security key and click OK. When you see Connected displayed next to the wireless network you selected, you have connected to the wireless network successfully. 130 Appendix 3 Factory Default Settings Item Router Login Network Settings Login IP Address Internet Type Connection MAC Address Default Settings 192.168.0.1 DHCP Find it on the label attached to the bottom of your device. PPPoE: 1450 Dynamic IP: 1450 Static IP: 1450 Auto-negotiation Disabled 192.168.0.1 255.255.255.0 Enabled 192.168.0.100~192.168.0.200
(GMT+08:00)Beijing, Chongquing, Hong Kong, Urumq Disabled last six characters in
(XXXXXX is the Enabled Tenda_XXXXXX the device's MAC address) Disabled 11b/g/n mixed Enabled Disabled Auto 20/40 Auto Enabled MTU WAN Speed DNS IP Address Subnet Mask DHCP Server IP Pool Time Zone Set Time and Date manually Wireless Primary
(Network Name) SSID Wireless Extender Network Mode SSID Broadcast AP Isolation Channel Channel Bandwidth Extension Channel WMM Capable LAN Settings Wireless Settings Tools APSD Capable Security Mode WPS Remote Management Disabled None Disabled Web Disabled Login Password None 131 Bandwidth Control Traffic Statistics DMZ Host UPnP Security Disabled Disabled Disabled Enabled Disabled Others 132 Appendix 4 FAQs This section provides solutions to problems that may occur during installation and operation of the device. Read the following if you are running into problems. If your problem is not covered here, please feel free to go to www.tendacn.com to find a solution or email your problems to: support@tenda.com.cn or support02@tenda.com.cn.Wewillbemorethanhappytohelpyououtassoonas possible. 1. Q: I cannot access the device's management interface. What should I do?
Make sure the power LED on the device's front panel is on and the SYS LED blinks normally. Make sure all cables are correctly connected and the corresponding LAN LED on the device is on. Verify that your PC's TCP/IP settings are configured correctly. If you select the "Use the following IP address" option, set your PC's IP address to any IP address between 192.168.0.2~192.168.0.254. Or you can select the
"Obtain an IP address automatically" option. Check the IP address you entered in your browser. It should be http://192.168.0.1. Open your browser and click Tools -> Internet Options -> Connections
-> LAN settings, uncheck the Use a proxy server for your LAN option. Press the WPS/RST button for over 7 seconds to restore your device to factory default settings. Then log to your device again. 2. Q: I changed the login password and unfortunately forget it. What should I do?
Press the WPS/RST button for over 7 seconds to restore your device to factory default settings. 3. Q: My computer shows an IP address conflict error after having connected to the device. What should I do?
Make sure there are no other DHCP servers on your LAN or other DHCP 133 servers are disabled. Make sure the device's LAN IP is not used by other devices on your LAN. The device's default LAN IP address is 192.168.0.1. Make sure the statically assigned IP addresses to the PCs on LAN are not used by others PCs. 4. Q: I have problems connecting to Internet/Secure websites do not open or displays only part of a web page. What should I do?
This problem mainly happens to users who use the PPPoE or Dynamic IP Internet connection type. You need to change the MTU size. Try changing the MTU to 1450 or 1400. If this does not help, gradually reduce the MTU from the maximum value until the problem disappears. 134 Appendix 5 Remove Wireless Network from Your PC If you change wireless settings on your wireless device, you must remove them accordingly from your PC; otherwise, you may not be able to wirelessly connect to this device. Below describes how to do remove a wireless network from your PC. Windows 7 Right-click the Network icon and select Properties. Select Manage Wireless Networks. 135 Select the wireless network and click Remove network. Windows XP Right-click My Network Places and select Properties. 136 Right click Wireless Network Connection and then select Properties. 137 Click Wireless Networks, select the wireless network name under Preferred networks and then click the Remove button. 138 Appendix 6 Safety and Emission Statement CE Mark Warning Operations in the 5.15-5.25GHz band are restricted to indoor usage only. This is a Class B product in a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures NOTE:(1)The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.(2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver. 139
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable 140
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2014-07-15 | 5745 ~ 5825 | DTS - Digital Transmission System | Original Equipment |
2 | 2014-07-11 | 5180 ~ 5240 | NII - Unlicensed National Information Infrastructure TX |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2014-07-15
|
||||
1 2 |
2014-07-11
|
|||||
1 2 | Applicant's complete, legal business name |
SHENZHEN TENDA TECHNOLOGY CO., LTD.
|
||||
1 2 | FCC Registration Number (FRN) |
0017645623
|
||||
1 2 | Physical Address |
6-8 Floor, Tower E3
|
||||
1 2 |
Shenzhen, N/A 518052
|
|||||
1 2 |
China
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
c******@telefication.com
|
||||
1 2 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
V7T
|
||||
1 2 | Equipment Product Code |
F1200
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
S******** Y********
|
||||
1 2 | Title |
Engineer
|
||||
1 2 | Telephone Number |
86-75********
|
||||
1 2 | Fax Number |
866-7********
|
||||
1 2 |
c******@tenda.cn
|
|||||
app s | Technical Contact | |||||
1 2 | Firm Name |
BTL Inc.
|
||||
1 2 | Name |
S******** L******
|
||||
1 2 | Physical Address |
China
|
||||
1 2 | Telephone Number |
86-76********
|
||||
app s | Non Technical Contact | |||||
1 2 | Firm Name |
BTL Inc.
|
||||
1 2 | Name |
C******** W********
|
||||
1 2 | Physical Address |
China
|
||||
1 2 | Telephone Number |
86-76********
|
||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | DTS - Digital Transmission System | ||||
1 2 | NII - Unlicensed National Information Infrastructure TX | |||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Wireless AC1200 Dual-band Router | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Original Equipment | ||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Power output listed is conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This device has 20/40/80 MHz bandwidth modes. | ||||
1 2 | Output power listed is conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation and transmitter operating conditions for satisfying RF exposure compliance. This device has 20/40/80 MHz bandwidth modes. The 80 MHz mode is limited to channel at 5210MHz. | |||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
BTL Inc.
|
||||
1 2 | Name |
D****** D****
|
||||
1 2 | Telephone Number |
86769******** Extension:
|
||||
1 2 | Fax Number |
+8676********
|
||||
1 2 |
d******@newbtl.org.cn
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | CC MO | 2412 | 2462 | 0.404 | |||||||||||||||||||||||||||||||||||
1 | 2 | 15C | CC MO | 5745 | 5825 | 0.413 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15E | CC | 5180.00000000 | 5240.00000000 | 0.0490000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC