Tenda WW OG Er}
WWO0' 287 Please read this install guide carefully before you start this device, For more information, visit our website at http://www.tendacn.com. Front 102.50 mm 410.00mm Package Contents Tenda Install Guide Wireless AP Screws Install Guide Ethernet Cable Power Adapter LEDs and Interfaces LED [Status |Description
[Birking [The devices enconing prover Jor The device is receiving no electrical power or the LED is disabled|
sys manually via Web interface
[Sona The device is functioning Improperly, Interface/Button |Description Reset Press it for over 7 seconds with a needle to restore factory default settings LAN/PoE Connect to an Ethernet device, such asa PC, a PoE device, ete 3 Installation Connect to a PoE Device Step 1: Place the Ethernet cable into the bracket
(Recommended: Cat5, CatSe or higher);
Step 2: Install the bracket onto the ceiling(Drill 4 holes on the ceiling, maneuver the bracket until it fits in the holes on the ceiling and then fix the bracket onto the ceiling with the provided screws.);
Step 3: Connect the Ethernet cable to the LA port of the device;
Step 4: Fix the device onto the bracket;
N Step 5: Connect the other end of the Ethernet cable to the PoE port on an IEEE 802.3at-compliant switch;
of Suite Step 6: Connected successfully!
(eX hc Me Nie Ls led Power Adapter Step 1: Place the Ethernet cable and power cord into the bracket;
Step 2: Install the bracket onto the ceiling(Drill 4 holes on the ceiling, maneuver the bracket until it fits in the holes on the ceiling and then fix the bracket onto the ceiling with the provided screws.);
the device;
Step 4: Fix the device onto the bracket;
v(t
(cue Step 3: Connect the Ethernet cable and power cord to Step 5: Connect the other end of the Ethernet cable toa switch and plug the included power adapter into a power outlet;
Step 6: Connected successfully!
C] Management PC Tenda SN Sea Configure PC Step 1: Click the icon fil on the right bottom corner of your desktop;
Step 2 : Click Open Network and Sharing Center;
Step 3 : Click Local Area Connection -> Properties:
Step 4: Find and double click Internet Step 5: Select Use the following IP address, IP Protocol Version 4(TCPIIP v4):
land click OK;
window (see Step 4 for the screenshot) 192.168.0.X (2~253); Subnet mask: 255.255.255.0 Step 6: Click OK on the Local Area Connection Properties Step 1 : Right click My Network Plac desktop and select Properties;
Step 2 : Right click Local Area Connection and select Properties;
address on your double click it;
oll down to find Internet Protocol (TCP/IP) and Step elect Use the following IP address, IP address 192.168.0.X (2~253); Subnet mask: 255.255.255.0 and click OK:
Step 5: Click OK on the Local Area Connection Properties window (see Step 3 for the screenshot) dX SMOPUIM Mi note Aner tnshing settings on Quick Setup interace, please refer io 4. Configure PC to setyour Configure AP Step 1 : Launch a web browser, input 192.168.0.254 in the address bar and Step 2: LAN Setup;
press Enter, 192.168.0.254 sane PLAN Setup EZTip inwos andar client mode, Static IP mustbe selected. PC to Obtain an IP address automatically, and then you can surf the Internet. cick Sve Status my Quick Sot ae Un seten al a oe Step 3 : Wireless Security Settings. 1 Glick dul Seton Wi-Fi Connection step 1: ciick the icon tl), Hor #8) onthe sight hotiom comer of your deskiop, Step 2 : Double click your SSID and then follow onscreen instructions Right click My Network PI Connected
&_ successfully!
oo dX SMOPUIM your desktop and select Properties;
laces on onscreen instructions. Q1: | enter the device's LAN IP address in the web browser but cannot access the utility. What should | do?
a. Check the TCP/IP settings on your PC and verify that the IP address is 192.168.0.X (2~253);
b. Clear the browser cache or try another web browser;
c. Ensure the wireless NIC is functioning properly. If you are still unable to login, please restore the device to factory default settings and follow the install guide to configure all settings again. Q2: What should | do if | cannot find the wireless signal?
a. Ensure the wireless feature on your PC is enabled;
b. Ensure the device is receiving electrical power;
c. Ensure no huge metal objects or other severe interferences (cordless telephones or microwaves, etc.) around. Q3: Wireless connection shows Connected but | cannot access the Internet. What should | do?
a. Verify that you are connecting to a right SSID;
b. Verify that you have set your PC to Obtain an IP address automatically;
c. Verify that other wireless devices (such as smart phones) connecting to this device can access the Internet. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class 8 digital device, pursuant to Part 18 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation, If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the useris encouraged to try o correct the interference by one of the following measures. Rearient or relocate the receiving antenna Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help, FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could vold the user's authority to operate this equipment, This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter, The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment, This equipment should be installed and operated with minimum distance 20em between the radiator & your body. NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, tis recommended to use a shielded RJ45 cable. EP Tip 1. thePc youuse must have an installed wireless network adapter ; 2. The defauit wireless network name (SSID) is Tenda_ XXXXXX, where XXXXXX is the last six characters ofthe device's MAC address. You can find the MAC address onthe label athe bottom of his device. Find and double click your SSID and then follow successfully!
C&
CE Mark Warning This is @ Class B product, In a domestic environment, this product may cause radio Interference, in which case the user may be required to take adequate measures, This device complies with EU 1999/5/EC. NOTE: (1) The manufacturer is not responsible for any radio or TY interference caused by unauthorized modifications to this equipment, (2) To avoid unnecessary radiation interference, itis recommended to use a shielded RJ45 cable, Shenzhen Tenda Technology Co., Ltd. 6-8 Floor, Tower E3, No. 1001, Zhongshanyuan Road, Nanshan District, Shenzhen China. 518052 Phone : (86 755)2765 7180 Fax : (86 755)2765 7178 Email : sales@tenda.com.cn support@tenda.com.cn Website: http://www.tendacn.com