all | frequencies |
|
|
exhibits | applications |
---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User manual 1 | Users Manual | 2.91 MiB | December 12 2013 | |||
1 |
|
User manual 2 | Users Manual | 3.25 MiB | December 12 2013 | |||
1 | Cover Letter(s) | December 12 2013 | ||||||
1 | External Photos | December 12 2013 | ||||||
1 | Cover Letter(s) | December 12 2013 | ||||||
1 | RF Exposure Info | December 12 2013 | ||||||
1 | Internal Photos | December 12 2013 | ||||||
1 | ID Label/Location Info | December 12 2013 | ||||||
1 | Test Report | December 12 2013 | ||||||
1 | Test Setup Photos | December 12 2013 | ||||||
1 | Cover Letter(s) | December 12 2013 |
1 | User manual 1 | Users Manual | 2.91 MiB | December 12 2013 |
Wireless N150/N300 Portable Router I Wireless N150/N300 Portable Router Copyright Statement is the registered trademark of Shenzhen Tenda Technology Co., Ltd. All the products and product names mentioned herein are the trademarks or registered trademarks of their respective holders. Copyright of the whole product as integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd. No part of this publication can be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means without the prior written permission of Shenzhen Tenda Technology Co., Ltd. If you would like to know more about our product information, please visit our website at http://www.tendacn.com. Disclaimer Pictures, images and product specifications herein are for references only. To improve internal design, operational function, and/or reliability, Tenda reserves the right to make changes to the products described in this document without obligation to notify any person or organization of such revisions or changes. Tenda does not assume any liability that may occur due to the use or application of, the product or circuit layout(s) described herein. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information and recommendations in this document do not constitute the warranty of any kind, express or implied. II Wireless N150/N300 Portable Router Preface Thank you for choosing Tenda! Please read this user guide before you start! This user guide instructs you to install and configure your device. This user guide uses the following formats to highlight special messages:
Icon Note:
Tip Description This format is used to highlight information of importance or special interest. Ignoring this type of note may result in ineffective configurations, loss of data or damage to device. This format is used to highlight a procedure that will save time or resources. Description of fields on the device GUI. Knowledge Center Technical Support support02@tenda.com.cn YouTube: Tendasz1999 Hotline:
1-800-570-5892 (USA) (061) 1300787922 (Australia)
(044)197-780-6119 (UK) (0852)36120883 (HongKong)
(064) 800787922 (New Zealand) Website: http://www.tendacn.com III Wireless N150/N300 Portable Router Contents Preface.........................................................................................................................................................III Contents.....................................................................................................................................................IV IProductOverview........................................................................................................................................1 1PackageContent..............................................................................................................................................1 2Gettingtoknowyourrouter............................................................................................................................1 LED..................................................................................................................................................................1 Button&Interface..........................................................................................................................................2 Label...............................................................................................................................................................3 IIQuickInternetSetup...................................................................................................................................4 1GettingPrepared..............................................................................................................................................4 2Install................................................................................................................................................................4 3ConnecttoRouter............................................................................................................................................6 3.1ConfigurePCTCP/IPSettings....................................................................................................................6 3.2JoinYourWirelessNetwork......................................................................................................................6 4AutodetectingInternetConnectionType.....................................................................................................12 5InternetSetup................................................................................................................................................14 5.1WebLogin...............................................................................................................................................14 5.2ManualInternetSetup&WirelessSecuritySetup..................................................................................15 6VerifyInternetConnectivity...........................................................................................................................27 IIIFeatures&Configurations.......................................................................................................................30 1AdvancedSettings..........................................................................................................................................30 1.1Status......................................................................................................................................................30 1.2.InternetSetup........................................................................................................................................31 1.3MACClone..............................................................................................................................................35 1.4WANSpeed.............................................................................................................................................35 1.5LANSettings............................................................................................................................................36 1.6DNSSettings............................................................................................................................................37 1.7DHCPServer............................................................................................................................................38 1.8DHCPClientList......................................................................................................................................39 2WirelessSettings............................................................................................................................................42 2.1WirelessBasicSettings...........................................................................................................................42 2.2WirelessSecurity....................................................................................................................................56 2.3WirelessAccessControl..........................................................................................................................57 2.4WirelessClients.......................................................................................................................................58 3BandwidthControl.........................................................................................................................................58 3.1BandwidthControl..................................................................................................................................58 3.2TrafficStatistics.......................................................................................................................................60 IV Wireless N150/N300 Portable Router 4SpecialApplications.......................................................................................................................................61 4.1PortRangeForwarding...........................................................................................................................61 4.2DMZHost................................................................................................................................................63 4.3DDNS.......................................................................................................................................................64 4.4UPNP.......................................................................................................................................................67 4.5StaticRouting..........................................................................................................................................67 4.6RoutingTable..........................................................................................................................................72 5Security..........................................................................................................................................................72 5.1URLFilter.................................................................................................................................................72 5.2MACFilter...............................................................................................................................................74 5.3ClientFilter..............................................................................................................................................75 6Tools...............................................................................................................................................................77 6.1Reboot....................................................................................................................................................77 6.2RestoretoFactoryDefaultSettings........................................................................................................77 6.3Back/Restore...........................................................................................................................................78 6.4Logs.........................................................................................................................................................82 6.5RemoteWebManagement....................................................................................................................82 6.6Time........................................................................................................................................................84 6.7LoginPassword.......................................................................................................................................86 6.8FirmwareUpgrade..................................................................................................................................86 IVAppendix.................................................................................................................................................89 1ConfigurePCTCP/IPSettings.........................................................................................................................89 Windows7....................................................................................................................................................89 WindowsXP..................................................................................................................................................95 2DefaultSettings..............................................................................................................................................98 3FAQs.............................................................................................................................................................100 4RemoveWirelessNetworkfromYourPC....................................................................................................102 Windows7..................................................................................................................................................102 WindowsXP................................................................................................................................................103 5SafetyandEmissionStatement....................................................................................................................105 V I Product Overview I Product Overview 1 Package Content Unpack the package. Your box should contain the following items:
If any of the parts are incorrect, missing, or damaged, contact your dealer. Keep the carton, including the original packing materials, in case you need to return the product for repair. 2 Getting to know your router LED 1 I Product Overview LED Status Description Power Solid Off The device is functioning correctly. Power is not supplied to the router. Make sure the device is properly connected to power outlet. A green and blinking light Device is currently operating in hotel mode and WAN port is NOT properly connected A green and solid light Device is currently operating in hotel mode and WAN port is connected A blinking blue light Device is currently operating in residence mode and WAN port is NOT properly connected Status A solid blue light Device is currently operating in residence mode and WAN port is connected A light blue and blinking light Device is currently operating in Universal Repeater Mode and is not connected to a wireless hotspot A light blue and solid light Device is currently operating in Universal Repeater Mode and is connected to a wireless hotspot. Button & Interface 2 I Product Overview 1RST: Pressing it for over 10seconds restores the device to factory default settings. For device's factory default settings, see Appendix 3 Factory Default Settings. 2USB: The USB port that charges terminal devices such as a smart phone or an iPad over a USB cable. 3LAN: The local (LAN) 100M Ethernet ports are for cabling the device to local computers, switches, etc. 4WAN/LAN: 100M LAN/WAN interchangeable interface, which functions as: a) a WAN interface for connecting to an Internet-enabled DSL modem or other uplink network device when operating in Residence Mode or Hotel Mode; or b) a LAN interface for connecting to a PC or an Ethernet switch when operating in Universal Repeater Mode. Label 1 Product Model 2 Default Login IP address. This IP address is to be used to access the routers settings through a web browser. If you change it, you have to open a new connection to the new IP address and log in again. 3 Default login password 4 Default wireless network name (SSID). 3 II Quick Internet Setup II Quick Internet Setup 1 Getting Prepared Before you start the installation process, you need to prepare the following:
Item Router PC Ethernet Cable Ethernet Cable from the incoming Internet side Description Find it in your package Should have a installed IE8 or higher browser You will need it to connect your PC to the router This is provided by your ISP If your ISP uses a PPPoE Internet connection, you will need ISP If you use a DHCP Internet connection, no information is needed. If your ISP gives you a fixed or static IP address for Internet Your Internet service provider (ISP) should have provided you with all of the information needed to connect to the Internet. If you cannot locate this information, ask your ISP to provide it. login name and password. connection, you will need to gather the following information:
1) IP Address 2) Subnet Mask 3) Gateway 4) DNS Server 5) Alternate DNS Server (Optional) Gather Information ISP 2 Install Note----------------------------------------------------------------------------------------------------------------------
Before you start, make sure you can access Internet by directly connecting the Ethernet cable from the incoming Internet side to your PC.
---------------------------------------------------------------------------------------------------------------------------------
Plug the device into a power outlet (For better wireless performance, place it near the center of the area where your computers, smart phones and other devices operate, and preferably within line of sight to your wireless devices.) 4 II Quick Internet Setup Connect the NIC port on your PC to one LAN port on the router using an Ethernet cable or connect to the router wirelessly. Connect the Ethernet cable from the incoming Internet side to the WAN port on the router. 5 II Quick Internet Setup 3 Connect to Router If you use a wired NIC, refer to 3.1 Configure PC TCP/IP Settings and then 4 Auto-switch Mode. 3.1 Configure PC TCP/IP Settings If your computer is set to a static or fixed IP address (this is uncommon), change it to "Obtain an IP address automatically" and "Obtain DNS server address automatically" from the device. Tip ------------------------------------------------------------------------------------------------------------------------
If you are unsure, see Appendix1 Configure PC TCP/IP Settings.
---------------------------------------------------------------------------------------------------------------------------------
3.2 Join Your Wireless Network Tip-------------------------------------------------------------------------------------------------------------------------
1. The device's SSID is "Tenda_xxxxxx" by default (You can find it on the attached label). 2. 3. To join your wireless network, the PC you use must have an installed wireless network adapter. If you secure your wireless network, you must use the security key to join it. If not, install one. 6 II Quick Internet Setup Windows 7 Click the icon on the notification area on the bottom right corner. 7 II Quick Internet Setup Select the wireless network you wish to connect and click Connect. If you see the screen below, you are connecting to the wireless network. Enter the security key and click OK. 8 II Quick Internet Setup When you see Connected displayed next to the wireless network you selected, you have connected to the wireless network successfully. 9 II Quick Internet Setup Windows XP Right click My Network Places from your PC's desktop and select Properties. Right click Wireless Network Connection and select View Available Wireless Networks. 10 II Quick Internet Setup Double click the wireless network you wish to connect. Enter the security key and click Connect. 11 II Quick Internet Setup When you see Connected displayed next to the wireless network you selected, you have connected to the wireless network successfully. 4 Auto-detecting Internet Connection Type By default, this device automatically detects and switches between DHCP and PPPoE according to actual environment. To test Internet connectivity:
Launch a web browser and enter the device's IP address. Input the default password (admin) and click OK on the login window. 12 II Quick Internet Setup The following screen appears if DHCP Internet connection type is detected. Simply specify a wireless security key, click Save and then close the browser. The following screen appears if PPPoE Internet connection type is detected. Enter the ISP login name and password, specify a wireless security key, and then click Save. 13 II Quick Internet Setup See whether you can access Internet (See 3.2 Join Your Wireless Network, if you use a wireless NIC), if not, refer to 5 Internet Setup. Tip-------------------------------------------------------------------------------------------------------------------------
If the Auto-switch feature is disabled, the device will automatically detect and switch to the right Internet connection type in case of an Internet connection failure.
---------------------------------------------------------------------------------------------------------------------------------
5 Internet Setup Read this section only when you fail to access Internet after you tried the above mentioned steps or you can access Internet and want to change the SSID (wireless network name) and security key of this device. 5.1 Web Login Launch a web browser, say, IE. In the address bar, input 192.168.2.1, and press "Enter". Enter the login password and click OK. The default password is admin. 14 II Quick Internet Setup Click Home on the appearing screen. The Setup Wizard screen appears. Tip-------------------------------------------------------------------------------------------------------------------------
1. If you access Internet by connecting to the Ethernet cable from the incoming Internet side, see Static IP. 2. If you don't want to use the Auto-switch feature, check the Disable Auto-switch mode box. 3. You can also enable the Auto-switch mode feature after you manually set up Internet and your wireless network so that your router can fit different environment, eliminating manual intervention.
---------------------------------------------------------------------------------------------------------------------------------
5.2 Manual Internet Setup& Wireless Security Setup Read the following and determine your Internet connection type. Then follow the right setup wizard. A. If your ISP provides you with an Ethernet cable from the incoming Internet side but no ISP login account or IP information, your ISP uses a DHCP connection. See DHCP. B. If your ISP provides you with an Ethernet cable from the incoming Internet side and ISP login account, your ISP uses a PPPoE connection. See PPPoE. 15 II Quick Internet Setup C. If your ISP provides you with an Ethernet cable from the incoming Internet side IP information
(IP address, subnet mask, gateway IP address, DNS server address), your ISP uses a static IP connection. See Static IP . D. If you acquire Internet access from a remote AP on an existing network see Universal Repeater Mode. Hotel Mode (DHCP) If your ISP does not give you any IP or user name/password info (your ISP uses a DHCP connection), simply connect the network cable from the incoming Internet side to the router and the router to your PC or simply search for and connect to your wireless router from your notebook. No configuration needed, simply plug and play. For typical network topology, see below:
Tip------------------------------------------------------------------------------------------------------------------------
1. If you already have a wired router, you can use this wireless router (operating in this mode) to convert the wired network into a wireless network. Simply connect the WAN port on this wireless router to a LAN port on the wired router and a wireless access point will be created instantly. 2. If your computer is set to a static or fixed IP address (this is uncommon), change it to obtain an IP address automatically from the router. For more information, see Appendix 1 Configure PC TCP/IP Settings.
---------------------------------------------------------------------------------------------------------------------------------
16 II Quick Internet Setup Configuration Procedures:
Select Hotel Mode: Dynamic IP and click Next. Configure your wireless network: SSID, channel, security settings and then click Next. SSID: Tenda_221988 Channel: 6 Security Mode: WPA-PSK Cipher Type: AES Security Key: 12345678 17 II Quick Internet Setup MAC Clone Setup: Enter the computer or broadband modem authorized by your ISP. Then click Next. Click Finish and wait for the device to restart automatically. After reboot, reconnect to this device wirelessly or using an Ethernet cable and you will be able to access Internet. Residence Mode If your ISP uses a PPPoE Internet connection (Router operates in Residence Mode), you will need ISP login name and password. For common application scenario, see below:
18 II Quick Internet Setup Configuration Procedures:
Select Residence Mode: PPPoE and click Next. Configure your wireless network: SSID, channel, security settings and then click Next. SSIDTenda_221988 Channel: 6 Security Mode: WPA-PSK Cipher Type: AES Security Key: Myrouter 19 II Quick Internet Setup Internet Setup & MAC Clone: Enter your ISP login user name and password (case sensitive) and the MAC address of the computer or broadband modem authorized by your ISP. Then click Next. Click Finish and wait for the device to restart automatically. After reboot, reconnect to this device wirelessly or using an Ethernet cable and you will be able to access Internet. 20 II Quick Internet Setup Universal Repeater Mode Use this universal repeater mode to extend your existing wireless network coverage. For application scenario, see below:
In this mode, you only need to configure the following settings on the repeater wireless router:
Configure LAN IP: Specify an IP address that is in the same subnet as yet different from the remote wireless router for this Tenda wireless router. Universal Repeater: Configure this router to bridge the remote wireless router for extended network coverage. Tip ---------------------------------------------------------------------------------------------------------------------
Before you start, make sure you have the following information:
1. Remote router's SSID, security mode, cipher type and security key. 2. Remote router's LAN IP address. 3. No Ethernet cable is connected to the Repeater wireless router's WAN port. 21 II Quick Internet Setup Universal Repeater Application Example:
Step 1 Gather information of the remote wireless router:
SSID: Tenda_888 Security Mode: WPA-PSK Cipher Type: AES Security Key: 12345678 LAN IP Address: 192.168.2.1 Step 2 Configure Repeater Wireless Router:
Click Advanced -> LAN Settings to configure an IP address that is in the same subnet as yet different from the remote wireless router for this Tenda wireless router. Click OK in the appearing screen. Select Universal Repeater Mode: Client +AP and click Next. 22 II Quick Internet Setup Click here to search for available APs. Select the wireless network you wish to connect to. The information of the remote AP will be added automatically. You only need to enter the security key. 23 II Quick Internet Setup Click Clear and Next. Click Finish and wait for the device to restart automatically. After reboot, reconnect to this device wirelessly or using an Ethernet cable and you will be able to access Internet. Note----------------------------------------------------------------------------------------------------------------------
When the Universal Repeater is configured successfully, wireless clients need to join the repeater wireless router's SSID for Internet access. Step 3: Configure PC3 & PC4 If PC 3 and PC 4 are set to static or fixed IP addresses (This is uncommon), change them to
"Obtain an IP address automatically" and "Obtain DNS server address automatically" from the device. For details, see Appendix 1Configure PC TCP/IP Settings. Tip------------------------------------------------------------------------------------------------------------------------
If PC 3 and PC 4 are already set to "Obtain an IP address automatically" and "Obtain DNS 24 II Quick Internet Setup server address automatically" from the device, click Repair to repair the IP settings.
--------------------------------------------------------------------------------------------------------------------------------
Wait until your PC successfully obtains an IP address. 25 II Quick Internet Setup Verify Connectivity:
On PC 3 or PC4, Click Start -> Run. Enter cmd and click OK. 26 II Quick Internet Setup Input ping 192.168.2.1 and press Enter. If you get a screen as seen below, you have successfully implemented WDS. 6 Verify Internet Connectivity Click Advanced-> Status and check the Connection Status. A If connection status displays "Connected (as shown below), you are connected to the Internet. 27 II Quick Internet Setup B. If connection status displays "Disconnected (as shown below), the Ethernet cable from the incoming Internet side to the router's WAN port may be connected improperly or disconnected. Make sure the cable from the incoming Internet side is properly connected to the router's WAN port. If nothing is wrong, "Connecting" or "Connected" will be displayed. C. If connection status displays "Connecting, wait until the webpage automatically refreshes 5 times. And if it still displays "Connecting", try the following steps:
If you are using DHCP Internet connection type, try cloning MAC address. For more 28 II Quick Internet Setup information, see 1.3 MAC Clone. If you are using the PPPoE Internet connection type, read the diagnostic information next to the Diagnose Connection Status on the screen. 29 III Features &Connectivity III Features & Configurations 1 Advanced Settings 1.1 Status Click Advanced to enter the status screen. Here you can view the routers WAN status and system status as noted below:
Tip----------------------------------------------------------------------------------------------------------------------
1. IP Address/Subnet Mask/WAN subnet mask/Gateway/Primary DNS Server/Secondary DNS Server: This type of information appears only if the router successfully connects to Internet via a PPPoE or DHCP (dynamic IP) connection. However if you connect the router to Internet with static IP settings provided by your ISP, these fields will display the settings you entered whether the router successfully connects to the Internet or not. 2. If nothing appears in the secondary DNS server field, there is no available secondary DNS server.
--------------------------------------------------------------------------------------------------------------------------------
30 III Features &Connectivity 1.2. Internet Setup Click Advanced -> Internet Connection Setup to configure your Internet connection settings. Select your Internet connection type:
A. Select PPPoE if your ISP uses a PPPoE connection and gives you a PPPoE user name and a PPPoE password. B. Select Static IP if your ISP provides you with fixed or static IP address settings (special deployment by ISP; this is rare). C. Select DHCP (Dynamic IP) if you can access Internet simply by directly connecting your computer to an Internet-enabled ADSL/Cable modem without configuring any settings. PPPoE Configuration Procedures:
Internet Connection Type: Select PPPoE. PPPoE Username: Enter the ISP login name. PPPoE Password: Enter the ISP login password. Click OK to save your settings. Knowledge Center----------------------------------------------------------------------------------------------
1. MTU: The MTU (maximum transmission unit) is the largest data packet a network device 31 III Features &Connectivity transmits. The normal MTU value for most Ethernet networks is 1500 bytes, or 1492 bytes for PPPoE connections. The best MTU value is often just the factory default value. For some ISPs, you might need to change the MTU. This is rarely required, and should not be done unless you are sure it is necessary for your ISP connection. For more information, see WAN MTU Setup. 2. Service Name: This is the descriptive name of the current connection. Only enter it if your ISP provides it. 3. Server Name: This is the descriptive name of the server. Only enter it if your ISP provides it.
-------------------------------------------------------------------------------------------------------------------------------
Static IP Configuration Procedures:
Internet connection Type: Select Static IP. IP Address/Subnet Mask/WAN subnet mask/Gateway/DNS Server/Alternate DNS Server:
Enter the ISP information you gathered in 1Getting Prepared. Click OK to save your settings. 32 III Features &Connectivity DHCP Configuration Procedures:
Internet connection Type: Select DHCP. Click OK to save your settings. WAN MTU Setup The MTU (maximum transmission unit) is the largest data packet a network device transmits. The normal MTU value for most Ethernet networks is 1500 bytes, or 1492 bytes for PPPoE connections. For some ISPs, you might need to change the MTU. This is rarely required, and should not be done unless you are sure it is necessary for your ISP connection. When one network device communicates across the Internet with another, the data packets travel through many devices along the way. If a device in the data path has a smaller MTU value than the other devices, the data packets have to be "fragmented" to accommodate the device with the smallest MTU value. The best MTU value is often just the factory default value. In some situations, changing the MTU value fixes one problem but causes another. Leave the MTU unchanged unless one of these situations occurs:
A. You have problems connecting to your ISP or other Internet service, and either your ISP or our technical support suggests changing the MTU value. Below web-based applications might require an MTU change:
A secure website that does not open, or displays only part of a web page 33 III Features &Connectivity Yahoo email MSN portal B. You use VPN and encounter serious performance problems. C. You used a program to optimize MTU for performance reasons, and now you have connectivity or performance problems. If you suspect an MTU problem, try changing the MTU to 1400. If this does not help, gradually reduce the MTU from the maximum value of 1500 until the problem disappears. The common MTU sizes and applications are listed in the table below. MTU 1500 1492 1472 Application Typical for connections that do not use PPPoE or VPN. Used in PPPoE environments. Maximum size to use for pinging. (Larger packets are fragmented.) Used in some DHCP environments. Used in PPTP environments or with VPN. 1468 1436 Note ---------------------------------------------------------------------------------------------------------------------
A wrong/improper MTU value may cause Internet communication problems. For example, you may be unable to access certain websites, frames within websites, secure login pages, or FTP or POP servers.
---------------------------------------------------------------------------------------------------------------------------------
34 III Features &Connectivity 1.3 MAC Clone Some ISPs (Internet Service Providers) require end-user's MAC address to access their network. This feature copies your current PC's MAC address to the router. Click Advanced -> MAC Clone to enter the configuration screen. Knowledge Center-----------------------------------------------------------------------------------------------
1. Restore Default MAC: Reset the routers WAN MAC to factory default. 2. Clone MAC Address: Clicking this button copies the MAC address of the computer that you are now using to the router. Also, you can manually enter the MAC address that you want to use. You have to use the computer whose MAC address is allowed by your ISP.
---------------------------------------------------------------------------------------------------------------------------------
To restore default MAC address:
Click Restore Default MAC. Click OK to save your settings. To clone the MAC address of the computer that you are currently using to the router:
Click Clone MAC Address. Click OK to save your settings. To manually enter the MAC address allowed by your ISP:
Enter the MAC address allowed by your ISP. Click OK to save your settings. 1.4 WAN Speed 35 III Features &Connectivity Click Advanced -> WAN Speed to enter the WAN port mode screen. Here you can configure the router's WAN speed and duplex mode. Tip-------------------------------------------------------------------------------------------------------------------------
1. The best port mode is often just the factory default of "Auto". 2. In some situations, you might need to change the port mode. For example, if the cable connected to your router's WAN port is too long, you may need to use 10M full-duplex or 10M half-duplex for better performance.
---------------------------------------------------------------------------------------------------------------------------------
1.5 LAN Settings Click Advanced -> LAN Settings to enter the configuration screen. Here you can configure the LAN IP address. This IP address is to be used to access the routers settings through a web browser. Be sure to make a note of any changes you apply to this page. Tip ----------------------------------------------------------------------------------------------------------------------
1. Default IP address and subnet mask are respectively 192.168.2.1 and 255.255.255.0. 2. This router does not support VLSM. 3. Be sure to make a note of any changes you apply to this page. If you change the LAN IP address of the router, you have to open a new connection to the new IP address and log in again.
---------------------------------------------------------------------------------------------------------------------------------
36 III Features &Connectivity Configuration Procedures:
Change the IP address to the one you wish to use, for example, 192.168.10.1. Click OK to save your settings. 1.6 DNS Settings Click Advanced -> DNS Settings to enter the configuration screen. Here you can set the DNS
(Domain Name Server) settings. The DNS server is used to look up site addresses based on their names. Configuration Procedures:
Enable Manual DNS Assignment: Check to enable the DNS settings. Primary DNS Server: Enter the IP address of your ISPs primary DNS server. Alternate DNS Address: If a secondary DNS server address is available, enter it here. This field is optional. Click OK to save your settings. 37 III Features &Connectivity Note --------------------------------------------------------------------------------------------------------------------
The default DNS settings are recommended. Only change the DNS default settings if you know that your ISP requires specific servers. If incorrect DNS settings are configured, webpages will be unable to open.
---------------------------------------------------------------------------------------------------------------------------------
1.7 DHCP Server DHCP (Dynamic Host Configuration Protocol) assigns an IP address to each device on the LAN/private network. When you enable the DHCP Server, the DHCP Server will automatically allocate an unused IP address from the IP address pool specified in this screen to the requesting device as long as the device is set to "Obtain an IP Address Automatically". If you disable this feature, you have to manually configure the TCP/IP settings for all PCs on your LAN to access Internet. Click Advanced -> DHCP Server to enter the DHCP Server screen. Here you can change the DHCP IP address pool and lease time. 38 III Features &Connectivity Configuration Procedures:
DHCP Server: Select whether to enable or disable the DHCP server feature. IP Pool Start IP Address / IP Pool End IP Address: You can specify the starting and ending address of the IP address pool here. These addresses should be part of the same IP address subnet as the routers LAN IP address. Lease Time: The lease time is a time length that the IP address is assigned to each device before it is refreshed. Click OK to save your settings. Tip-----------------------------------------------------------------------------------------------------------------------
1. By default, the router functions as a DHCP server. Do not disable the DHCP server feature unless you want to manually configure the TCP/IP settings for all PCs on your LAN. 2. Lease time will be renewed automatically upon expiry. No additional configurations are needed. 3. If you are not an advanced user, the default DHCP server settings are recommended.
---------------------------------------------------------------------------------------------------------------------------------
1.8 DHCP Client List Click Advanced -> DHCP Client List. You can know whether there are unauthorized accesses by viewing the client list. Also, you can specify a reserved IP address for a PC in the LAN. That PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses could be assigned to servers that require permanent IP settings. 39 III Features &Connectivity Static Assignment Application Example:
To have a PC at the MAC address of 44:37:E6:4F:37:3B always receive the same IP address of 192.168.0.123. Configuration Procedures:
Enter the last number of the IP address you want to reserve, for example, 123. Enter the MAC address of 44:37:E6:4F:37:3B. Click Add. 40 III Features &Connectivity Click OK to save your settings. Tip-------------------------------------------------------------------------------------------------------------------------
1. If the IP address you have reserved for your PC is currently used by another client, then you will not be able to obtain a new IP address from the device's DHCP server, instead, you must manually specify a different IP address for your PC to access Internet. 2. For PCs that has already obtained IP addresses, you may need to perform the Repair action to activate the configured static IP addresses.
---------------------------------------------------------------------------------------------------------------------------------
41 III Features &Connectivity 2 Wireless Settings 2.1 Wireless Basic Settings Here you can configure the basic wireless settings of the router. This router supports two operating modes: Wireless Access Point (AP) and WDS Bridge Mode. A. To only use the wireless network delivered by this router, select Wireless Access Point (AP). B. To extend an existing wireless network, select WDS Bridge Mode. Wireless AP Mode Tip-----------------------------------------------------------------------------------------------------------------------
1. By default, this device operates in the Wireless Access Point (AP) mode. 2. The primary SSID is defaulted to Tenda_XXXXXX, where XXXXXX is the last six characters in the device's MAC address. You can find this SSID on the label attached on the bottom of the device. 3. If you are not an advanced user, it is advisable to only change the primary SSID (name of the network) and channel and leave other items unchanged. 4. The device supports two SSIDs: primary SSID and secondary SSID. The secondary SSID is optional. By default, the secondary SSID is disabled. 5. Instructions to configure the primary SSID also apply to the secondary SSID. The primary SSID is used as an example below to illustrate all wireless related features.
---------------------------------------------------------------------------------------------------------------------------------
42 III Features &Connectivity Configuration Procedures:
Primary SSID: This is the public name of your wireless network. Channel: Select a channel or select Auto to let system automatically select one for your wireless network to operate on if you are unsure. The best selection is a channel that is the least used by neighboring networks. Click OK to save your settings. Knowledge Center---------------------------------------------------------------------------------------------
1. Secondary SSID: This is an alternate name for your wireless network. 2. Network Mode (802.11 Mode): Select a correct mode according to your wireless clients. 11b: This network mode delivers wireless speed up to 11Mbps and is only compatible with 11b wireless clients. 11g: This network mode delivers wireless speed up to 54Mbps and is only compatible with 11g wireless clients. 11b/g mixed: This network mode delivers wireless speed up to 54Mbps and is compatible with 11b/g wireless clients. 11b/g/n mixed: This network mode delivers wireless speed up to 300Mbps (A31)/150Mbps
(A8) and is compatible with 11b/g/n wireless clients. 3. SSID Broadcast: This option allows you to have your network names (SSIDs) publicly broadcast or if you choose to disable it, the SSIDs will be hidden. 4. AP Isolation: When enabled, devices wirelessly connected to the same SSID will not be able to intercommunicate. 5. Channel Bandwidth: Select a proper channel bandwidth to enhance wireless performance. This option is available only in 802.11b/g/n. Wireless speed in the channel bandwidth of 20/40 is 2 times in 20. 6. Extension Channel: This is used to ensure N speeds for 802.11n devices on the network. This option is available only in 11b/g/n mixed mode with channel bandwidth of 20/40. 7. WMM Capable: WMM is QoS for your wireless network. Enabling this option may better stream wireless multimedia data (such as video or audio). 8. ASPD Capable: Select to enable/disable the auto power saving mode. This option is effective only if WMM Capable is enabled. It is advisable to disable it. 43 III Features &Connectivity WDS Bridge Mode WDS Bridge Mode: wireless distribution system (WDS) is a system enabling the wireless interconnection of access points in an IEEE 802.11 network. It allows a wireless network to be expanded using multiple access points without the traditional requirement for a wired backbone to link them. Note----------------------------------------------------------------------------------------------------------------------
The Access Points you select MUST support WDS.
---------------------------------------------------------------------------------------------------------------------------------
44 III Features &Connectivity WDS Bridge Mode Application Example:
To implement WDS Bridge for the application scenario above, do as follows:
Step 1: Get Prepared View and note down the SSID and wireless security settings of Router 1. Click Wireless -> Wireless Basic Settings to enter the wireless basic configuration screen. Here you can view the SSID and channel. SSIDTenda_221988 Channel: 6 Click Wireless -> Security to enter the wireless security configuration screen. Here you can view the security settings. 45 III Features &Connectivity Security Mode: WPA-PSK Cipher Type: AES Password: 12345678 AP MAC (BSSID): C8:3A:35:00:01:20 (can be found on the label attached to the device) Make sure DHCP server is enabled on router 1. Click Advanced -> DHCP Server to enter the DHCP server configuration screen. You can view and configure the DHCP server settings here. Set the LAN IP address of Router 1 to a different address yet on the same net segment as Router 2. For example, Router 1: 192.168.2.1, Router 2: 192.168.2.10. About how to configure these IP addresses, see 1.6 LAN Setting. 46 III Features &Connectivity Step 2: Configure Router 1 Set the LAN IP address of Router 1 (Set it to a different address yet on the same net segment as Router 2. For example, Router 1: 192.168.2.1, Router 2: 192.168.2.10). For more information, see 1.6 LAN Settings. Click Wireless -> Wireless Basic Settings to enter the configuration screen. Select WDS Bridge Mode and click Open Scan. 47 III Features &Connectivity Select the AP you wish to connect to and click OK to confirm it and then click Close Scan. Verify that the automatically populated SSID, channel and MAC address, etc. are correct and then click OK. 48 III Features &Connectivity Step 3: Configure Router 2 Configure the LAN IP address of Router 2 49 III Features &Connectivity Click Wireless -> Wireless Basic Settings to enter the configuration screen. Select WDS Bridge Mode and click Open Scan. 50
1 | User manual 2 | Users Manual | 3.25 MiB | December 12 2013 |
III Features &Connectivity Select the AP you wish to connect to (The SSIDs of these two wireless networks become the same now. You need to identify them by their MAC addresses.) . Click OK on the appearing dialog box and then close scan. Check the automatically populated SSID, channel and MAC address, etc of the remote AP. Verify that all settings are correct and then click OK. 51 III Features &Connectivity Set the security key of Router 2 to the same as Router 1. Click Wireless -> Security to set the security settings to match the remote device (Security Mode:
WPA2-PSK, Cipher Type: AES, Security Key: 12345678). Click Advanced -> DHCP Server and disable the DHCP server on Router 2 (Disable DHCP server on the local router that is used to extend the wireless network from the remote Internet-enabled router). Tip-------------------------------------------------------------------------------------------------------------------------
If WDS connection fails, try a different security mode and/or cipher type.
---------------------------------------------------------------------------------------------------------------------------------
52 III Features &Connectivity Step 4: Configure PC3 & PC4 If PC 3 and PC 4 are set to static or fixed IP addresses (This is uncommon), change them to
"Obtain an IP address automatically" and "Obtain DNS server address automatically" from the device. For details, see Appendix 1Configure PC TCP/IP Settings. Tip-----------------------------------------------------------------------------------------------------------------------
If PC 3 and PC 4 are already set to "Obtain an IP address automatically" and "Obtain DNS server address automatically" from the device, click Repair to repair the IP settings.
--------------------------------------------------------------------------------------------------------------------------------
Wait until your PC successfully obtains an IP address. 53 III Features &Connectivity Verify Bridge Connectivity:
On PC 3, Click Start -> Run. Enter cmd and click OK. 54 III Features &Connectivity Input ping 192.168.2.1 and press Enter. If you get a screen as seen below, you have successfully implemented WDS. Note ---------------------------------------------------------------------------------------------------------------------
1 WDS feature can only be implemented between 2 WDS-capable wireless devices. Plus, SSID, channel, security settings and security key must be exactly the same on both such devices. 2 To ensure a proper wireless connection, do not change any settings on the two devices after WDS is successfully implemented.
---------------------------------------------------------------------------------------------------------------------------------
55 III Features &Connectivity 2.2 Wireless Security Click Wireless -> Wireless Security to enter the Wireless Security screen. Here you can define a security key to secure your wireless network against unauthorized accesses. Configuration Procedures:
Select the wireless network (SSID) you wish to encrypt. Configure security mode, cipher type and security key. Click OK to save your settings. Knowledge Center-----------------------------------------------------------------------------------------------
1. Open: Wireless speed can reach up to 54Mbps if WEP - Open is selected. 2. Shared: Wireless speed can reach up to 54Mbps if WEP - Shared is selected. 3. Default key: Select a key to be effective for the current WEP encryption. For example, if you select Key 1, wireless clients must join your wireless network using this Key 1. 4. WPA-PSK: WPA personal, support AES and TKIP cipher types. 5. WPA2-PSK: WPA2 personal, support AES, TKIP and TKIP+AES cipher types. 6. WPA/WPA2-PSK mixed: If selected, both WPA-PSK and WPA2-PSK secured wireless clients can join your wireless network. 7. AES: If selected, wireless speed can reach up to 300Mbps. 8. TKIP: If selected, wireless speed can reach up to 54Mbps. 9. TKIP+AES: If selected, both AES and TKIP secured wireless clients can join your wireless network. 56 III Features &Connectivity
---------------------------------------------------------------------------------------------------------------------------------
2.3 Wireless Access Control Specify a list of devices to "Permit" or "Forbid" a connection to your wireless network via the devices MAC Addresses. Click Wireless -> Wireless Access Control to enter the configuration screen. There are three options available: Disable, Forbid and Permit. A. If you want to allow all wireless clients to join your wireless network, select Disable. B. If you want to allow ONLY the specified wireless clients to join your wireless network, select Permit. C. If you want to disallow ONLY the specified wireless clients to join your wireless network, select Forbid. Wireless Access Control Application Example:
To only allow your own notebook at the MAC address of C8:3A:35:CC:34:25 to join your wireless network Configuration Procedures:
Select the wireless network (SSID) you wish to enable Access Control on. Select Permit. Enter the MAC address of the wireless device you want to restrict. Here in this example, enter C8:3A:35:CC:34:25. 57 III Features &Connectivity Click Add to add the MAC address to the MAC address list. Click OK to save your settings. Tip-------------------------------------------------------------------------------------------------------------------------
1. Up to 16 wireless MAC addresses can be configured. 2. If you don't want to configure the complex wireless security settings and want to disallow others to join your wireless network, you can configure a wireless access control rule to allow only your own wireless device.
---------------------------------------------------------------------------------------------------------------------------------
2.4 Wireless Clients Click Wireless -> Wireless Connection Status. Here you can see a list of wireless devices connected to the router. Tip-------------------------------------------------------------------------------------------------------------------------
1. The bandwidth here refers to the channel bandwidth instead of wireless connection rate. You can know whether there are unauthorized accesses to your wireless network by viewing the wireless client list.
---------------------------------------------------------------------------------------------------------------------------------
3 Bandwidth Control 3.1 Bandwidth Control If there are multiple PCs behind your router competing for limited bandwidth resource, then you can use this feature to specify a reasonable amount of bandwidth for each such PC, so that no one will be over stuffed or starved to death. Tip-------------------------------------------------------------------------------------------------------------------------
1. 1M=128KByte/s. 2. The volume of uplink traffic/downlink traffic should not be larger than that allowed on your 58 III Features &Connectivity router's WAN (Internet) port. You can ask your ISP to provide the volume of Internet traffic.
---------------------------------------------------------------------------------------------------------------------------------
Bandwidth Control Application Example:
You share a 4M-broadband service with your neighbor (at 192.168.2.100) who always downloads a large volume of data from Internet. Your Internet surfing experience is thus affected seriously. In this case, use this feature to set limits for the volume of Internet traffic he/she can get. For example, you can equally split the bandwidth, so your neighbor can only use up to 2M Internet traffic and you can happily enjoy 2M. Configuration Procedures:
Enable Bandwidth Control: Check the Enable box to enable the Bandwidth Control feature. IP Address: Enter the last number of the IP address. Here in this example, enter 100 in both boxes. Upload/Download: Select Download from the drop-down list. Bandwidth Range: Set a limit to regulate download bandwidth of PCs on the LAN. Here in this example, enter 256 in both boxes. Enable: Check to enable the current rule. Add to List: Click to add current rule to the rule list. Click OK to save your settings. 59 III Features &Connectivity 3.2 Traffic Statistics Traffic Statistics meter allows you to monitor and view the volume of traffic used by LAN devices. Click QoS-> Traffic Statistics to enter the Statistics screen. Tip------------------------------------------------------------------------------------------------------------------------
If you suspect some PCs behind your router are consuming a large volume of bandwidth
(downloading videos, etc) you can enable this Traffic Statistics meter feature to find out which PCs are overusing the traffic. Enabling the Traffic Statistics feature may degrade the routers performance. Do not enable it unless necessary.
--------------------------------------------------------------------------------------------------------------------------------
Configuration Procedures:
Check Enable Traffic Statistics. Click OK to save your settings. Knowledge Center----------------------------------------------------------------------------------------------
1. IP Address: Displays the IP addresses of the PCs that have connected to the device. 2. Uplink Rate: Displays the upload speed (KByte/s) of a corresponding PC. 3. Downlink Rate: Displays the download speed (KByte/s) of a corresponding PC. 4. Sent Message: The number of packets transmitted by a corresponding PC upon traffic statistics meter startup. 5. Sent Bytes: The number of bytes transmitted by a corresponding PC upon traffic statistics meter startup. The unit is MByte. 6. Received Message: The number of packets received by a corresponding PC upon traffic statistics meter startup. 7. Received Bytes: The number of bytes received by a corresponding PC upon traffic statistics 60 III Features &Connectivity meter startup. The unit is MByte.
--------------------------------------------------------------------------------------------------------------------------------
4 Special Applications 4.1 Port Range Forwarding You want to share resources on your PC with your friends who are not in your LAN. But, by default, the router's firewall blocks inbound traffic from the Internet to your computers except replies to your outbound traffic. You can use the Port Forwarding feature to create exceptions to this rule so that your friends can access these files from external networks. Click Applications to enter the configuration screen. Application Example:
As shown in the figure above, your PC at 192.168.2.100 connects to the router and runs a FTP server on port number 21. Your friends want to access this FTP server on your PC from external network. Tip------------------------------------------------------------------------------------------------------------------------
1. Make sure your WAN IP address (Internet IP address) is a public IP address. Private IP addresses are not routed on the Internet. 2. Make sure you enter correct service port numbers. 3. To ensure that your server computer always has the same IP address, assign a static IP address to your PC. 4. Operating System built-in firewall and some anti-virus programs may block other PCs from accessing resources on your PC. So it is advisable to disable them before using this feature.
---------------------------------------------------------------------------------------------------------------------------------
61 III Features &Connectivity Configuration Procedures:
Start Port: Enter the starting port number for the service. Here in this example, enter 21. End Port: Enter the ending port number for the service. Here in this example, enter 21. LAN IP: Enter the IP address of your local computer that will provide this service. Here in this example, enter 192.168.2.100. Protocol: Specify the protocol required for the service utilizing the port(s). Check Enable to activate this rule. Click OK to save your settings. Now, your friends only need to enter ftp://xxx.xxx.xxx.xxx:21in their browsers to access your FTP server. xxx.xxx.xxx.xxx is the router's WAN IP address. For example, if it is 172.16.102.89, your friends need to enter ftp://202.33.56.88:21. 62 III Features &Connectivity 4.2 DMZ Host The DMZ (De-Militarized Zone) function disables the firewall on the router for one device for a special purpose service such as Internet gaming or video conferencing applications that are not compatible with NAT (Network Address Translation). Click Applications -> DMZ Host to enter the DMZ Host screen. Note --------------------------------------------------------------------------------------------------------------------
1. DMZ host poses a security risk. A computer configured as the DMZ host loses much of the protection of the firewall and becomes vulnerable to attacks from external networks. 2. Hackers may use the DMZ host computer to attack other computers on your network.
---------------------------------------------------------------------------------------------------------------------------------
Configuration Procedures:
DMZ Host IP Address: The IP Address of the device for which the routers firewall will be disabled. Be sure to statically set the IP Address of that device for this function to be consistent. Enable: Check to enable the DMZ host. Click OK to save your settings. 63 III Features &Connectivity Tip-------------------------------------------------------------------------------------------------------------------------
1. Be sure to statically set the IP Address of the computer that serves as a DMZ host for this function to be consistent. 2. Security softwares such as anti-virus software and OS built-in firewall, etc may affect the DMZ host feature. Disable them if DMZ host fails.
---------------------------------------------------------------------------------------------------------------------------------
4.3 DDNS Dynamic DNS or DDNS is a term used for the updating in real time of Internet Domain Name System (DNS) name servers. We use a numeric IP address allocated by Internet Service Provider
(ISP) to connect to Internet; the address may either be stable ("static"), or may change from one session on the Internet to the next ("dynamic"). However, a numeric address is inconvenient to remember; an address which changes unpredictably makes connection impossible. The DDNS provider allocates a static host name to the user; whenever the user is allocated a new IP address this is communicated to the DDNS provider by software running on a computer or network device at that address; the provider distributes the association between the host name and the address to the Internet's DNS servers so that they may resolve DNS queries. Thus, uninterrupted access to devices and services whose numeric IP address may change is maintained. Click Applications -> DDNS to enter the configuration screen. Tip------------------------------------------------------------------------------------------------------------------------
1. To use the DDNS feature, you need to have an account with one of the Service Providers in the drop-down menu first. 2. This router supports two DDNS service providers: dyndns and no-ip.
---------------------------------------------------------------------------------------------------------------------------------
DDNS Application Example:
If your ISP gave you a dynamic (changing) public IP address, you want to access your router remotely (6.5 Remote Web Management) but you cannot predict what your router's WAN IP address will be, and the address can change frequently. In this case, you can use a commercial Dynamic DNS service. It lets you register your domain to their IP address and forwards traffic directed at your domain to your frequently changing IP address. If you obtain the following account from your dyndns.org service provider:
User Name: tenda Password: 123456 64 III Features &Connectivity Domain Name: tenda.dyndns.org. You want to use the PC at 218.58.98.3 to remotely access this router on port number 8090. Configuration Procedures:
DDNS Service: Select Enable. Service Provider: Select your DDNS service provider from the drop-down menu. Here in this example, select dyndns. User Name: Enter the DDNS user name registered with your DDNS service provider. Here in this example, enter tenda. Password: Enter the DDNS Password registered with your DDNS service provider. Here in this example, enter 123456. Domain Name: Enter the DDNS domain name with your DDNS service provider. Here in this example, enter tenda.dyndns.org. Click OK to save your settings. 65 III Features &Connectivity Click Tools -> Remote Web Management, enable the Remote Web Management feature, enter 8090 in the Port field, 218.58.98.3 in the IP Address field and then click OK to save your settings. Now you can access the router from the Internet by entering http://tenda.dyndns.org:8090 in your browser. 66 III Features &Connectivity 4.4 UPNP The Universal Plug and Play (UPnP) feature allows network devices, such as computers from Internet, to access resources on local host or devices as needed. UPnP-enabled devices can be discovered automatically by the UPnP service application on the LAN. If you use applications such as multiplayer gaming, peer-to-peer connections, real-time communications such as instant messaging, or remote assistance (a feature in Windows XP), you may need to enable Universal Plug and Play (UPnP) for better experience. Click Applications -> UPnP Settings to enter the configuration screen. The UPnP feature is enabled by default. 4.5 Static Routing Static routes provide additional routing information to your router. Typically, you do not need to add static routes. However, when there are several routers in the network, you may want to set up static routing. Static routing determines the path of the data in your network. You can use this feature to allow users on different IP domains to access the Internet via this device. It is not recommended to use this setting unless you are familiar with static routing. In most cases, dynamic routing is recommended, because this feature allows the router to detect the physical changes of the network layout automatically. If you want to use static routing, make sure the routers DHCP function is disabled. Click Applications -> Static Routing to enter the configuration screen. 67 III Features &Connectivity Tip------------------------------------------------------------------------------------------------------------------------
1. Gateway must be on the same IP segment as WAN or LAN segment as the router. 2. Subnet Mask must be entered 255.255.255.255 if destination IP address is a single host.
-------------------------------------------------------------------------------------------------------------------------------
Static Route Application Example - Gateway IP address on the same IP segment as WAN IP:
For example, your company internal network and Internet are on different IP net segment and you want PCs on your LAN to access Internet and your company internal network via the Tenda Router. You can simply configuring static routes on the Tenda Router. The figure above depicts this application scenario. 68 III Features &Connectivity Configuration Procedures:
Destination Network IP Address: The IP address of the final destination. Enter your corporate internal network address: 172.16.100.0. Subnet Mask: Enter the subnet mask of your corporate internal network: 255.255.255.0. Gateway: Enter the gateway IP address to your corporate internal network: 192.168.30.88 Click Add to add a static route. Click OK to save your settings. Click Applications -> Routing Table to view your static route entry. If it does not display, go to Tools to reboot your router. Enter the router's management interface. When the router successfully connects to the Internet, the following screen will display:
69 III Features &Connectivity Static Route Application Example - Gateway IP address on the same IP segment as LAN IP:
As seen in the above figure, PC2 on LAN2 connects with the Tenda Router via the Router; PC1 on LAN1 accesses Internet via the Tenda Router that performs NAT. You can configure static routes to implement mutual communication between PCs on LAN1 and LAN2. 70 III Features &Connectivity Configuration Procedures:
Destination Network IP Address: Enter 192.168.53.0. Subnet Mask: Enter 255.255.255.0. Gateway: Enter 192.168.0.101. Click Add to add the rule. Click OK to save your settings. Click Applications -> Route Table to view your static route entry. If it does not display, go to Tools to reboot your router. Enter the router's management interface. When the router successfully connects to the Internet, the following screen will display:
71 III Features &Connectivity 4.6 Routing Table Click Applications -> Routing Table to view the router's route table. Knowledge Center-----------------------------------------------------------------------------------------------
1. Destination IP: The IP address of the final destination. "0.0.0.0" indicates any network segment. 2. Subnet Mask: The subnet mask for the specified destination. 3. Gateway: This is the next router on the same LAN segment as the router to reach. 4. Hops: This stands for the number of routers between your network and the destination. 5. Interface: The interface between your router and the final destination.
---------------------------------------------------------------------------------------------------------------------------------
5 Security This router provides three security policies: MAC filter, client filter and URL filter. To restrict your LAN PCs to access certain websites on Internet via URL, see URL Filter. To restrict your LAN PCs to access Internet via MAC addresses, see MAC Filter. To restrict your LAN PCs to access certain services on Internet via their IP addresses, see Client Filter. 5.1 URL Filter This section allows you to control URL access. There are two options available: Disable and Deny. A Disable: Disable the URL Filter feature. B Deny: Disallow only the devices at specific IP addresses to access certain websites
(containing specified URL characters) on Internet during the specific time period and/or 72 III Features &Connectivity specific days of the week. Click Security to enter the configuration interface. Tip-------------------------------------------------------------------------------------------------------------------------
1. Each rule can only include a single domain name. To filter multiple domain names, set a rule for each domain name. 2. Time/Day: If Time is set to 0:00 to 0:00 and Day is set to Sun ~ Sat, the rule will be applied 24 hrs/day. 3. If you have not set up the system time for this device, click Tools -> Time Settings to set up correct time and date for the rules to be effective. For more information, see 6.6 Time.
---------------------------------------------------------------------------------------------------------------------------------
URL Filter Application Example:
If you want to disallow the computers (192.168.2.100~192.168.2.101) on your home network to access "YouTube" within the time period from 900 to 1700 during working days: Monday ~
Friday, then do as follows:
Configuration Procedures:
Filter Mode: Select Deny. Select: Select a rule ID, for example, (1). Description: Briefly describe the current rule, say, yahoo, (It can only consist of numbers, letters, or underscore). This field is optional. Start IP/End IP: Enter 100-101. URL Character String: Enter the domain name you wish to filter out. Here in this example, 73 III Features &Connectivity enter YouTube. Time: Specify a time period for the current rule to take effect. Here in this example, select 9:00~17:00. Day: Select a day, or several days of the week for the current rule to take effect. Here in this example, select Mon ~ Fri. Click OK to save your settings. 5.2 MAC Filter This section allows you to restrict specific clients to access the Internet via the devices MAC addresses. Each PC has at least an installed network adapter with a unique MAC address. Three options are available: Disable, Forbid Only and Permit Only. A. Disable: Disable the MAC Filter feature. B. Forbid Only: Disallow only the devices at specific MAC addresses to access Internet during the specific time period and/or specific days of the week. B. Permit Only: Allow only the devices at specific MAC addresses to access Internet during the specific time period and/or specific days of the week. Click Security -> MAC Address Filter Settings to enter the configuration interface. Tip------------------------------------------------------------------------------------------------------------------------
1. Time/Date: If Time is set to 0:00 to 0:00 and Day is set to Sun ~ Sat, the rule will be applied 24 hrs/day. 2. If you have not set up the system time for this device, click Tools -> Time Settings to set up correct time and date for the rules to be effective. For more information, see 6.6 Time.
--------------------------------------------------------------------------------------------------------------------------------
MAC Filter Application Example:
Your router functions as an active DHCP server and delivers an unsecured wireless network. From time to time, you suffer from slow network speed and start to suspect unauthorized accesses to your network. You can set MAC filter rules to allow only your PC at 00:E4:A5:44:35:69 and your wireless device at 00:E4:A5:44:35:6A to access Internet via this router. 74 III Features &Connectivity Configuration Procedures:
Filter Mode: Select Permit Only. Access Policy: Select a rule ID, for example, (1). Policy Name: Briefly describe the current rule, say, yahoo, (It can only consist of numbers, letters, or underscore). This field is optional. MAC Address: Specify the MAC address of the computer that you want to restrict, 00:E4:A5:44:35:69. Time: Keep the default of 0:00 ~ 0:00. The rule will be applied 24hrs/day. Day(s): Select Mon ~ Fri. Enable: Check to activate this rule. Click OK to save your settings. Repeat steps 1-7 to configure a rule for the MAC address "00:E4:A5:44:35:6A". 5.3 Client Filter This section allows you to set the times specific clients can or cannot access services on the Internet via the devices' IP addresses and port numbers. Click Security -> Client Filter Settings to enter the configuration interface. Select a Policy from the drop-down menu and briefly describe it in the corresponding field. You can set the access restriction or permission in detail including the time period, and specific days of the week. Three options are available: Disable, Forbid Only and Permit Only. A. Disable: Disable the Filter feature. 75 III Features &Connectivity B. Forbid Only: Disallow only the devices at specific IP addresses to access certain services on Internet during the specific time period and/or specific days of the week. C. Permit Only: Allow only the devices at specific IP addresses to access certain services on Internet during the specific time period and/or specific days of the week. Tip-----------------------------------------------------------------------------------------------------------------------
1. The valid service port number range is from 1 to 65534. 2. Time/Day: If Time is set to 0:00 to 0:00 and Day is set to Sun ~ Sat, the rule will be applied 24 hrs/day. 3. If you have not set up the system time for this device, click Tools -> Time Settings to set up correct time and date for the rules to be effective. For more information, see 6.6 Time.
--------------------------------------------------------------------------------------------------------------------------------
Client Filter Application Example:
To disallow your family member (PC IP address: 192.168.2.150) to access web pages within the time period of 8:00~18:00 from Monday to Friday Configuration Procedures:
Filter Mode: Select Forbid Only. Access Policy: Select a rule ID, for example, (1). Policy Name (Optional): Briefly describe the current rule (It can only consist of numbers, letters, or underscore). This field is optional. Start IP: Enter a starting IP address. Here in this example, enter 150. 76 III Features &Connectivity End IP: Enter an ending IP address. Here in this example, enter 150. Port: Enter a service port number. Here in this example, enter 80. Type: Select a protocol for the traffic. If you are unsure, select Both. Time: Specify a time period for the current rule to take effect. Here in this example, select 8:00 ~18:00. Day(s): Select a day, or several days of the week for the current rule to take effect. Here in this example, select Mon ~ Fri. Enable: Check to enable the current rule. Click OK to save your settings. 6 Tools 6.1 Reboot When a certain feature does not take effect or the device fails to function correctly, try rebooting the device. 6.2 Restore to Factory Default Settings Click Tools -> Restore to Factory Default to enter the configuration screen. Here you can reset the device to factory default settings. Note----------------------------------------------------------------------------------------------------------------------
1. If you enable this option, all current settings will be deleted and be restored to factory default values. You will have to reconfigure Internet connection settings and wireless settings. 2. Do not restore factory default settings unless the following happens:
You need to join a different network or unfortunately forget the login password. You cannot access Internet and your ISP or our technical support asks you to reset the router.
---------------------------------------------------------------------------------------------------------------------------------
77 III Features &Connectivity The factory default settings are listed below:
IP Address: 192.168.2.1 Subnet Mask: 255.255.255.0. For more factory default settings, see 2 Default Settings. 6.3 Back/Restore Once you have configured the device the way you want it, you can save these settings to a configuration file on your local hard drive that can later be imported to your device in case that the device is restored to factory default settings. Click Tools -> Back/Restore to enter the configuration screen. Tip------------------------------------------------------------------------------------------------------------------------
The default configuration file name is "RouterCfm.cfg". Do include the file name suffix of ".cfg"
when renaming the file name to avoid problems.
---------------------------------------------------------------------------------------------------------------------------------
78 III Features &Connectivity To backup configurations Click Backup. Click OK on the appearing window. Click OK on the appearing alert window. 79 III Features &Connectivity Select a local hard drive to save the file and click Save. To restore configurations Click Browse. 80 III Features &Connectivity Select the configuration file that is saved previously to your local hard drive and click Open. Click the Restore button to reset your device to previous settings. 81 III Features &Connectivity 6.4 Logs Click Tools -> Syslog to enter the logs screen. Here you can view the history of the devices actions. Up to 150 entries can be logged. After 150 entries, you can click Refresh to update the logs or click Clear to clear the earliest logs. 6.5 Remote Web Management The Remote web management allows the device to be configured and managed remotely from the Internet via a web browser. Click Tools -> Remote Web Management to enter the configuration screen. Knowledge Center---------------------------------------------------------------------------------------------
1. Port: This is the management port to be open to outside access. The default setting is 8080. This can be changed. 2. IP Address: Here you can specify the IP address for remote management (When set to 0.0.0.0, the device becomes remotely accessible to all the PCs on Internet or other external networks).
--------------------------------------------------------------------------------------------------------------------------------
Remote Web Management Application Example:
To access your router (WAN IP address: 102.33.66.88) at your home from the PC (218.88.93.33) at your office via the port number 8090 82 III Features &Connectivity Configuration Procedures:
Enable: Check to enable the remote Web management feature. Port: This is the management port to be open to outside access. Here in this example, enter 8090. IP Address: Specify the IP address for remote management. Here in this example, enter
"218.88.93.33". Click OK to save your settings. Now you can access the router at your home by simply entering http://102.33.66.88:8090 in the web browser on the PC at your office. Tip-------------------------------------------------------------------------------------------------------------------------
1. For better security, customize a port number between 1025 and 65535 for the remote web management interface, do not use the number of any common service port (1-1024). 83 III Features &Connectivity 2. Make sure your WAN IP address (Internet IP address) is a public IP address. Private IP addresses are not routed on the Internet. 3. It is unsafe to make your router remotely accessible to all PCs on external network. For better security, we suggest that only enter the IP address of the PC for remote management. 4. You must change the default login password before you can enable this feature.
---------------------------------------------------------------------------------------------------------------------------------
6.6 Time Click Tools -> Time to enter the time screen. A. Sync with Internet time servers Configuration Procedures:
Select your time zone. Click OK to save your settings. Tip-------------------------------------------------------------------------------------------------------------------------
Configured time and date info will be lost if the device gets disconnected from power supply. However, it will be updated automatically when the device reconnects to Internet. To activate time-based features (e.g. firewall), the time and date info shall be set correctly first, either manually or automatically.
---------------------------------------------------------------------------------------------------------------------------------
84 III Features &Connectivity B. Set Time and Date Manually/Sync with Your PC Configuration Procedures:
Check Customized Time. Specify correct time and date. Click OK to save your settings. And then go to Status screen (Advanced -> Status) to make sure the system time is correctly updated. 85 III Features &Connectivity 6.7 Login Password Click Tools -> Change Password to enter the configuration screen. It is strongly recommended that you change the factory default login password. Otherwise, anyone in your network can access this utility to change your settings. Tip------------------------------------------------------------------------------------------------------------------------
1. The default login password is admin. Please change it for better security. 2. The password can include 0-12 characters. I f no character is entered (left blank), no password is set.
---------------------------------------------------------------------------------------------------------------------------------
Configuration Procedures:
Old Password: Enter the old password. New Password: Input a new password. Confirm New Password: Re-enter the new password for confirmation. Click OK to save your settings. 6.8 Firmware Upgrade Click Tools -> Upgrade to enter the configuration screen. Firmware upgrade is released periodically to improve the functionality of your device and also to add new features. If you run into a problem with a specific feature of the device, log on to our website (www.tendacn.com) to download the latest firmware to update your device. If you run into a problem with a specific feature of the device, log on to our website (www.tendacn.com) to download the latest firmware to update your device. 86 III Features &Connectivity Note ---------------------------------------------------------------------------------------------------------------------
1 Before you upgrade the firmware, make sure you are having a correct firmware. A wrong firmware may damage the device. 2 It is advisable that you upgrade the device's firmware over a wired connection. DO NOT interrupt the power to the router when the upgrade is in process otherwise the router may be permanently damaged.
---------------------------------------------------------------------------------------------------------------------------------
Configuration Procedures:
Click Browse. 87 III Features &Connectivity Select the upgrade file and click Open. Click Upgrade and wait until the upgrade progress indicator bar displays 100% completed. When upgrade is completed, view the Current System Version. It should display the firmware you load. 88 IV Appendix IV Appendix 1 Configure PC TCP/IP Settings Windows 7 Click Start -> Control Panel. 89 IV Appendix Click Network and Internet. Click Network and Sharing Center. 90 IV Appendix Click Change adapter settings. Click Local Area Connection and select Properties. 91 IV Appendix Select Internet Protocol Version 4 (TCP/IPv4) and click Properties. 92 IV Appendix Select Obtain an IP address automatically and click OK. 93 IV Appendix Click OK on the Local Area Connection Properties window to save your settings. 94 IV Appendix Windows XP Right-click My Network Places and select Properties. Right click Local Area Connection and select Properties. 95 IV Appendix Select Internet Protocol Version 4 (TCP/IPv4) and click Properties. 96 IV Appendix Select Obtain an IP address automatically and click OK. 97 IV Appendix Click OK on the Local Area Connection Properties window to save your settings. 2 Default Settings Item Login IP Address Default Settings 192.168.2.1 Login Password admin Internet Connection Type WAN MAC Address MTU WAN Speed DNS LAN Settings IP Address Subnet Mask DHCP Server IP Pool Hotel Mode (Dynamic IP) Find it on the label attached to the device PPPoE: 1492 DHCP: 1500 Static IP: 1500 Auto-negotiation Disabled 192.168.2.1 255.255.255.0 Enabled 192.168.2.100~192.168.2.150 98 IV Appendix System Time Wireless Primary Name) SSID
(Network Secondary SSID Wireless Working Mode Network Mode SSID Broadcast AP Isolation Channel Channel Bandwidth Extension Channel WMM Capable APSD Capable Security Mode Remote Web Management Bandwidth Control Traffic Statistics DMZ Host UPnP Security Internet By default, system automatically synchronizes with time servers. Time Zone: (GMT+08:00) Beijing, Chongqing, Hong Kong, Urumqi Enabled Tenda_XXXXXX (XXXXXX is the last six characters of the device's MAC address. You can find it on the label attached to the device.) Disabled Wireless AP 11b/g/n mixed Enabled Disabled AutoSelect 20/40 AutoSelect Enabled Disabled Disabled Disabled Disabled Disabled Disabled Enabled Disabled Wireless Others 99 IV Appendix 3 FAQs This section provides solutions to problems that may occur during installation and operation of the device. Read the following if you are running into problems. If your problem is not covered here, please feel free to go to www.tendacn.com to find a solution or email your problems to: support@tenda.com.cn or support02@tenda.com.cn. We will be more than happy to help you out as soon as possible. 1. Q: I cannot access the device's management interface. What should I do?
Make sure the power LED on the device's front panel is on. Make sure Ethernet cables are connected properly. Verify that your PC's TCP/IP settings are configured correctly. If you select the "Use the following IP address" option, set your PC's IP address to any IP address between 192.168.2.2~192.168.2.254. Or you can select the "Obtain an IP address automatically" option. Try a different browser or delete your existing browsers cache and cookies. Check the IP address you entered in your browser. It should be http://192.168.2.1. Open your browser and click Tools -> Internet Options -> Connections -> LAN Settings, uncheck the Use a proxy server for your LAN option. Press the reset button on the device with a needle for 10seconds to restore factory default settings and then re-access the device. 2. Q: I changed the login password and unfortunately forget it. What should I do?
Press the reset button on the device with a needle for 10seconds to restore factory default settings. 3. Q: My computer shows an IP address conflict error after having connected to the device. What should I do?
Make sure there are no other DHCP servers on your LAN or other DHCP servers are disabled. Make sure the device's LAN IP is not used by other devices on your LAN. The device's default LAN IP address is 192.168.2.1. Make sure the statically assigned IP addresses to the PCs on LAN are not used by others PCs. 100 IV Appendix 4. Q: I have problems connecting to Internet/Secure websites do not open or displays only part of a web page. What should I do?
This problem mainly happens to users who use the PPPoE or Dynamic IP Internet connection type. You need to change the MTU size. Try changing the MTU to 1450 or 1400. If this does not help, gradually reduce the MTU from the maximum value until the problem disappears. 101 IV Appendix 4 Remove Wireless Network from Your PC If you change wireless settings on your wireless device, you must remove them accordingly from your PC; otherwise, you may not be able to wirelessly connect to this device. Below describes how to do remove a wireless network from your PC. Windows 7 Right-click the Network icon and select Properties. Select Manage Wireless Networks. Select the wireless network and click Remove network. 102 IV Appendix Windows XP Right-click My Network Places and select Properties. Right click Wireless Network Connection and then select Properties. 103 IV Appendix Click Wireless Networks, select the wireless network name under Preferred networks and then click the Remove button. 104 IV Appendix 5 Safety and Emission Statement CE Mark Warning This is a Class B product in a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This device complies with EU 1999/5/EC. NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.(2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 105 IV Appendix
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.(2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable NCC Notice 106
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2013-12-12 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2013-12-12
|
||||
1 | Applicant's complete, legal business name |
SHENZHEN TENDA TECHNOLOGY CO., LTD.
|
||||
1 | FCC Registration Number (FRN) |
0017645623
|
||||
1 | Physical Address |
6-8 Floor, Tower E3, No. 1001, Zhongshanyuan Road,Nanshan District
|
||||
1 |
6-8 Floor, Tower E3
|
|||||
1 |
Shenzhen, N/A
|
|||||
1 |
China
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
c******@telefication.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
V7T
|
||||
1 | Equipment Product Code |
A31
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
S****** Y****
|
||||
1 | Title |
Engineer
|
||||
1 | Telephone Number |
86-75********
|
||||
1 | Fax Number |
866-7********
|
||||
1 |
c******@tenda.cn
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Neutron Engineering, Inc.
|
||||
1 | Name |
S******** L****
|
||||
1 | Physical Address |
No.3,Jinshagang 1st Rd, ShiXia,Dalang
|
||||
1 |
China
|
|||||
1 | Telephone Number |
86-76********
|
||||
1 | Fax Number |
86-76********
|
||||
1 |
s******@btl.org.cn
|
|||||
app s | Non Technical Contact | |||||
1 | Firm Name |
Neutron Engineering, Inc.
|
||||
1 | Name |
C**** W********
|
||||
1 | Physical Address |
No.3,Jinshagang 1st Rd, ShiXia,Dalang
|
||||
1 |
China
|
|||||
1 | Telephone Number |
86-76********
|
||||
1 | Fax Number |
86-76********
|
||||
1 |
c******@btl.org.cn
|
|||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Wireless N300 Portable Router | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power output listed is conducted. The antenna(s) used for this transmitter must be used to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This device has 20/40 MHz bandwidth modes. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
BTL Inc.
|
||||
1 | Name |
D**** D********
|
||||
1 | Telephone Number |
00867******** Extension:
|
||||
1 | Fax Number |
0086 ********
|
||||
1 |
d******@btl.org.cn
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | MO | 2412.00000000 | 2462.00000000 | 0.2900000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC