WWTMXS Smart Projector User Manual

Overview The remote control Basic parameters Remote control receiving Lens cover HDMI TF card DC-IN Power Focus -

Setting Arrow key Return Volume -

Power Belt Lens USB2.0 Reset Indicator light Headphone jack Air inlet Indicator Light Display technology DLP Size 140*104*97mm Keystone Correction Correction range Vertical 45 Horizontal 45 The cursor keys Weight 0.745Kg Throw ratio 1:2:1 4 direction correction Product type Portable The light source type Wireless connection LED Wi-Fi, Bluetooth Instrcution Power on Long press the power button above the projector for 2 seconds to start, or press the power button of the remote control to start the projector. Foucus +

OK Home Multifunction Volume +

Mute Indicator Light Red light Blue light Purple light Power off Charging Power Mode Charging completed (standby) Start Charging (starting) Battery Mode Battery Model Power off Power on Overheat Fan error ON OFF OFF OFF OFF Slow ash QuickFlash OFF OFF ON OFF ON OFF OFF OFF ON OFF OFF OFF OFF OFF A. Short press the power button of the projector or the power button of the remote control once. After the prompt window of shutdown/restart/music mode/timing appears, press the power button of the projector or OK key of the remote control to shut down. B.Long press the power button for 5 seconds to turn it off, as well as press the power button of the remote control twice to shut it down. Product upgrade Please ensure that the power of the projector is more than 50% or connected to the power supply (Please keep charging during the upgrade process). 1. Upgrade online with Wi-Fi 2. If there is a new rmware update in the local upgrade, you can download the latest Firmware from the ofcial website, put it into the USB drive and insert it into the USB port to upgrade. Indicator light description The fault The solution Unable to display projection Shut down and reboot Android crash Shut down and reboot Abnormal projection Shut down and reboot Remote control cannot trun on The projector is not connected to the power adapter, it can only be turned off and cannot be turned on. System prompt the peojrctor is overheated, or automatic shut-down Please do not block the front air outlet and rear air inlet mesh, restart Other system failures Please contact the after-sales supporting e-mail Connecting to Wi-Fi Connecting to Bluetooth Notice Wi-Fi is a wireless networking technology that can provide wireless Internet access. 1.Enter Home Screen > Wi-Fi. 2.Slide the Wi-Fi switch to the on position to turn on WI-FI. 3.The projector will scan for available Wi-Fi networks. 4.Choose a network name to connect to it. 5.If the network is secured, enter the password and enter Connect. NOTES: Your projector automatically connects to the previously used Wi-Fi network when they are in range. When Wi-Fi is connected, your projector can notify you by showing * ( ) in the status bar. Adding a Wi-Fi network You can add a Wi-Fi network if the network does not broadcast its name (SSID), or add a Wi-Fi network when you are out of range. To connect to a secured network, you rst need the security details from the network administrator. Sharing your device as a Wi-Fi Hotspot You can share your device with other devices by turning your projector into a Wi-Fi hotspot. Bluetooth is a short-range wireless communication technology. Phones or other devices with Bluetooth capabilities can exchange Information wirelessly. 1.Enter Home Screen > Bluetooth. 2.Slide the Bluetooth switch to the on position. NOTES:When Bluetooth is on, the icon will appear in the status bar. Changing the Device name 1.Enter Home Screen > Bluetooth. 2.Slide the Bluetooth switch to the on position to turn on Bluetooth. 3.Set name and password. 4.Enter Save. 1. When using the projector, please do not watch the lens directly to avoid damage to the eyes. 2. Please do not use in hot and humid environment. 3. Please do not block the air outlet or air inlet. 4. Install away from the wall In order to maintain the performance and feasibility of the projector, please leave at least 30cm between the projector and the wall. Warning:

* Block the projector Vented slits and openings.

* Wipe the device with a scrub, parafn or solvent.

* Used under the following conditions

- Extremely hot, cold or humid environment.

- Ensure indoor temperature is between 5-40.

- Relative humidity is 80% maximum at 5-40, no condensation.

- Areas susceptible to large amounts of dust and dirt.

-Near any equipment that produce strong magnet-

ic eld.

- Sunlight exposure directly.

- The product is suitable for non-tropical climate. Note:

Without the agreement of brand manufac-

turer, user disassembles the product, violently squeezes or impacts, uses in high temperature, high pressure, ammable and explosive environment, and uses the non-compliant method the to charge projector the projector requires 5V charging, user uses 9V or other high voltage charging) and other product dameged issues such as battery leakage, burning and other product quality and safety issues which is caused by human improper factors, the brand manufacturer does not bear any responsibility!

(for example, The color, appearance and specications of this product are subject to the actual product and may change without notice due to performance improvement. SAFETYINSTRUCTION: The projector built-in battery,do not use in high temperature and high humidity conditions. Product sit idle for a long time, ensure that three month a charge!

RF EXPOSURE WARNING This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This product may not be collocated or operated in conjunction with any other antenna or transmitter. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

1.Reorient or relocate the receiving antenna. 2.Increase the separation between the equipment and receiver. 3.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4.Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.