Hardware Integration Guide AirPrime MC7354B 4117529 1.0 June 12, 2015 Hardware Integration Guide Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data. Safety and Hazards Do not operate the Sierra Wireless modem in areas where cellular modems are not advised without proper device certifications. These areas include environments where cellular radio can interfere such as explosive atmospheres, medical equipment, or any other equipment which may be susceptible to any form of radio interference. The Sierra Wireless modem can transmit signals that could interfere with this equipment. Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE POWERED OFF. When operating, the Sierra Wireless modem can transmit signals that could interfere with various onboard systems. Note:
Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. Sierra Wireless modems may be used at this time. The driver or operator of any vehicle should not operate the Sierra Wireless modem while in control of a vehicle. Doing so will detract from the driver or operators control and operation of that vehicle. In some states and provinces, operating such communications devices while in control of a vehicle is an offence. Limitations of Liability This manual is provided as is. Sierra Wireless makes no warranties of any kind, either expressed or implied, including any implied warranties of merchantability, fitness for a particular purpose, or noninfringement. The recipient of the manual shall endorse all risks arising from its use. The information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY. Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability arising under or in connection with the Sierra Wireless product, regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the Sierra Wireless product. Customer understands that Sierra Wireless is not providing cellular or GPS (including A-GPS) services. These services are provided by a third party and should be purchased directly by the Customer. 4117529 Rev 1.0 June 12, 2015 2 Hardware Integration Guide SPECIFIC DISCLAIMERS OF LIABILITY: CUSTOMER RECOGNIZES AND ACKNOWLEDGES SIERRA WIRELESS IS NOT RESPONSIBLE FOR AND SHALL NOT BE HELD LIABLE FOR ANY DEFECT OR DEFICIENCY OF ANY KIND OF CELLULAR OR GPS (INCLUDING A-GPS) SERVICES. Patents This product may contain technology developed by or for Sierra Wireless Inc. This product includes technology licensed from QUALCOMM. This product is manufactured or sold by Sierra Wireless Inc. or its affiliates under one or more patents licensed from InterDigital Group and MMP Portfolio Licensing. Copyright 2015 Sierra Wireless. All rights reserved. Trademarks Sierra Wireless, AirPrime, AirLink, AirVantage, WISMO, ALEOS and the Sierra Wireless and Open AT logos are registered trademarks of Sierra Wireless, Inc. or one of its subsidiaries. Watcher is a registered trademark of NETGEAR, Inc., used under license. Windows and Windows Vista are registered trademarks of Microsoft Corporation. Macintosh and Mac OS X are registered trademarks of Apple Inc., registered in the U.S. and other countries. QUALCOMM is a registered trademark of QUALCOMM Incorporated. Used under license. Other trademarks are the property of their respective owners. Contact Information Phone:
1-604-232-1488 Sales Desk:
Hours:
8:00 AM to 5:00 PM Pacific Time Contact:
http://www.sierrawireless.com/sales Post:
Sierra Wireless 13811 Wireless Way Richmond, BC Canada V6V 3A4 Technical Support: support@sierrawireless.com RMA Support:
repairs@sierrawireless.com Fax: 1-604-231-1109 Web: http://www.sierrawireless.com/
Consult our website for up-to-date product descriptions, documentation, application notes, firmware upgrades, troubleshooting tips, and press releases: www.sierrawireless.com 4117529 Rev 1.0 June 12, 2015 3 Hardware Integration Guide Document History Version Date Updates 1.0 June 12, 2015 Creation 4117529 Rev 1.0 June 12, 2015 4 Contents 1. INTRODUCTION .................................................................................................. 7 1.1. Hardware Development Components ............................................................................... 7 2. POWER INTERFACE ........................................................................................... 8 2.1. 2.2. 2.3. Power Supply .................................................................................................................... 8 Electrostatic Discharge (ESD) ........................................................................................... 8 Power States ..................................................................................................................... 9 3. RF INTEGRATION ............................................................................................. 10 3.1. 3.2. 3.3. 3.4. Supported RF Bands ....................................................................................................... 10 Ground Connection ......................................................................................................... 11 Shielding Guidelines ........................................................................................................ 11 Antenna Guidelines ......................................................................................................... 11 Choosing the Correct Antenna and Cabling ............................................................ 11 Determining the Antennas Location ........................................................................ 11 3.4.1. 3.4.2. 3.5. RF Desense Sources ...................................................................................................... 12 4. AUDIO INTERFACE ........................................................................................... 13 5. REGULATORY INFORMATION......................................................................... 14 5.1. 5.2. 5.3. Important Notice .............................................................................................................. 14 Safety and Hazards ......................................................................................................... 14 Important Compliance Information for North American Users ........................................ 15 6. REFERENCES ................................................................................................... 17 6.1. 6.2. Reference Documents ..................................................................................................... 17 List of Abbreviations ........................................................................................................ 17 4117529 Rev 1.0 June 12, 2015 5 List of Tables Table 1. Power Supply Requirements ............................................................................................. 8 Table 2. ESD Specifications ............................................................................................................ 8 Table 3. Supported MC7354B Power States .................................................................................. 9 Table 4. Supported RF Bands ....................................................................................................... 10 Table 5. Audio Pin Description ...................................................................................................... 13 4117529 Rev 1.0 June 12, 2015 6 1. Introduction The Sierra Wireless AirPrime MC7354B PCI Express Mini Card is a compact, lightweight, wireless LTE-, UMTS-, CDMA- and GSM-based modem. It provides LTE, EVDO Rel 0, EVDO Rel A, DC-HSPA+, HSPA+, HSDPA, HSUPA, WCDMA, GSM, GPRS, EDGE and GNSS connectivity for networking, and M2M applications over several radio frequency bands. The device also supports 2G/3G roaming, subject to carrier provisioning. 1.1. Hardware Development Components Sierra Wireless manufactures the MC Series Development Kit, a hardware development component that is used to facilitate the hardware integration process. This development kit is the hardware development board on which an MC mini card is plugged. The development kit provides access to all of the interfaces supported by the MC mini card. For instructions on using the MC Development Kit, see document [2] AirPrime MC Series Development Kit Quick Start Guide. 4117529 Rev 1.0 June 12, 2015 7 2. Power Interface 2.1. Power Supply The host device must provide power to the MC7354B mini card over pins 2, 24, 39, 41 and 52 (VCC) as detailed in the following table. Table 1. Power Supply Requirements Signal Name Pin Specification Minimum Typical Maximum Unit VCC 2, 24, 39, 41, 52 Voltage range 3.0 Ripple voltage
-
-
3.3
-
0 3.6 100
-
V mVpp V 4, 9, 15, 18, 21, 26, 27, 29, 34, 35, 37, 40, 43, 50
-
GND Note:
The host must provide safe and continuous power at all times; the module does not have an independent power supply, or protection circuits to guard against electrical issues. 2.2. Electrostatic Discharge (ESD) The OEM is responsible for ensuring that the Mini Card host interface pins are not exposed to ESD during handling or normal operation. Note:
The level of protection required depends on your application. Table 2. ESD Specifications Connection Specification The RF port (antenna launch and RF connector) complies with the IEC 61000-4-2 standard:
Operational Electrostatic Discharge Immunity:
Test: Level3 Contact Discharge: 6 kV Air Discharge: 8 kV Non-operational The host connector Interface complies with the following standard only:
2 kV Human Body Model (JESD22-A114-B) 4117529 Rev 1.0 June 12, 2015 8 Hardware Integration Guide 2.3. Power States Power Interface The MC7354B mini card has four power states as detailed in the following table. Table 3. Supported MC7354B Power States State Details Host is Powered Module is Powered USB Interface Active RF Enabled Normal
(Default state) Low power
(Airplane mode) Module is active Default state when VCC is first applied in the absence of W_DISABLE_N control Module is capable of placing /
receiving calls, or establishing data connections on the wireless network Current consumption is affected by several factors, including:
Radio band being used Transmit power Receive gain settings Data rate Number of active Tx time slots Module is active Module enters this state:
Under host interface control:
Host issues AT+CFUN=0, or Host asserts W_DISABLE_N, after AT!PCOFFEN=0 has been issued. Automatically, when critical temperature or voltage trigger limits have been reached Normal state of module between calls or data connections Sleep Module cycles between wake
(polling the network) and sleep, at network provider-
determined interval. Disconnected Host power source is disconnected from the module and all voltages associated with the module are at 0 V. 4117529 Rev 1.0 June 12, 2015 9 3. RF Integration 3.1. Supported RF Bands Table 4. Supported RF Bands Technology Bands Band 2 (1900 MHz) Band 4 (AWS)
(1700/2100 MHz) Band 5 (850 MHz) Band 13 (700 MHz) Band 17 (700 MHz) Band 25 (1900 MHz) Band 26 (850 MHz) Band 1 (2100 MHz) Band 2 (1900 MHz) Band 4 (AWS)
(1700/2100 MHz) Band 5 (850 MHz) Band 8 (900 MHz) LTE UMTS
(WCDMA) HSDPA HSUPA HSPA+
DC-HSPA+
Data Rates Category 3 Downlink:
Notes 100 Mbps
(20 MHz bandwidth) 50 Mbps
(10 MHz bandwidth) Uplink:
50 Mbps
(20 MHz bandwidth) 25 Mbps
(10 MHz bandwidth) MIMO support HSPA+ rates:
Downlink: Up to 42 Mbps
(category 24) Uplink: Up to 5.76 Mbps
(category 6) Diversity support CDMA EVDO Rel 0 EVDO Rel A BC0 (Cellular 800 MHz) BC1 (PCS 1900 MHz) BC10 (Secondary 800 MHz) GSM GPRS EDGE GNSS GSM 850 (850 MHz) GSM 900 (900 MHz) DCS 1800 (1800 MHz) PCS 1900 (1900 MHz) GPS: 1575.42 MHz GLONASS: 1602 MHz CDMA IS-856
(1xEV-DO Release A) Up to 3.1 Mbps forward channel Up to 1.8 Mbps reverse channel CDMA IS-2000 Up to 153 kbps, simultaneous forward and reverse channel Circuit-switched data bearers up to 14.4 kbps Diversity support EDGE throughput up to 236 kbps 4117529 Rev 1.0 June 12, 2015 10 Hardware Integration Guide 3.2. Ground Connection When connecting the mini card to system ground:
RF Integration Prevent noise leakage by establishing a very good ground connection to the mini card through the host connector. Minimize ground noise leakage into the RF. Depending on the host board design, noise could potentially be coupled to the mini card from the host board. This is mainly an issue for host designs that have signals traveling along the length of the mini card, or when circuitry operating at both ends of the mini card interconnects. 3.3. Shielding Guidelines The mini card is fully shielded to protect against EMI and to ensure compliance with FCC Part 15 -
Radio Frequency Devices (or equivalent regulations in other jurisdictions). Note:
The module shields must NOT be removed. 3.4. Antenna Guidelines 3.4.1. Choosing the Correct Antenna and Cabling Consider the following points for appropriate antenna selection:
The antenna (and associated circuitry) should have a nominal impedance of 50 with a return loss of better than 10 dB across each frequency band of operation. The system gain value affects both radiated power and regulatory (FCC, IC, CE, etc.) test results. 3.4.2. Determining the Antennas Location Consider the following points when deciding where to place the antenna:
Antenna location may affect RF performance. Although the module is shielded to prevent interference in most applications, the placement of the antenna is still very importantif the host device is insufficiently shielded, high levels of broadband or spurious noise can degrade the modules performance. Connecting cables between the module and the antenna must have 50 impedance. If the impedance of the module is mismatched, RF performance is reduced significantly. Antenna cables should be routed, if possible, away from noise sources (switching power supplies, LCD assemblies, etc.) If the cables are near the noise sources, the noise may be coupled into the RF cable and into the antenna. 4117529 Rev 1.0 June 12, 2015 11 Hardware Integration Guide 3.5. RF Desense Sources RF Integration Common sources of interference that may affect the modules RF performance (RF desense) which include:
Power supply noise Can lead to noise in the RF signal Module power supply ripple limit <= 100 mVp-p 1 Hz100 kHz Interference from other embedded wireless devices Any harmonics, sub-harmonics, or cross-products of signals that fall in the modules Rx range may cause spurious response, resulting in decreased Rx performance. Tx power and corresponding broadband noise may overload or increase the noise floor of the modules receiver, resulting in RF desense. Severity of interference depends on proximity of other antennas to the modules antennas. Host electronic device-generated RF Proximity of host electronics to the modules antenna can contribute to decreased Rx performance. Some devices include microprocessor and memory, display panel and display drivers, and switching mode power supplies. Note:
In practice, there are usually numerous interfering frequencies and harmonics. The net effect can be a series of desensitized receive channels. 4117529 Rev 1.0 June 12, 2015 12 4. Audio Interface The MC7354B supports a PCM/I2S digital audio interface using a dedicated serial link for digital audio data; all other signals, such as subcoding and control, are transmitted separately. The audio interface can be switched from PCM to I2S and vice versa via AT commands. Table 5. Audio Pin Description Signal Name Pin Description PCM_CLK/I2S_CLK 45 PCM Clock/I2S Clock PCM_DOUT/I2S_DOUT 47 PCM Data Out/I2S Data Out PCM_DIN/I2S_DIN PCM_SYNC/I2S_WS 49 51 PCM Data In/I2S Data In PCM SYNC/I2S WS 4117529 Rev 1.0 June 12, 2015 13 5. Regulatory Information This module is designed to meet, and upon commercial release, will meet the requirements of the following regulatory bodies and regulations, where applicable:
Federal Communications Commission (FCC) of the United States The Certification and Engineering Bureau of Industry Canada (IC) The National Communications Commission (NCC) of Taiwan, Republic of China Upon commercial release, the following industry approvals will have been obtained, where applicable:
PTCRB CDG2 Additional certifications and details on specific country approvals may be obtained upon customer request; contact your Sierra Wireless account representative for details. Additional testing and certification may be required for the end product with an embedded AirPrime MC7354B modem and are the responsibility of the OEM. Sierra Wireless offers professional services-
based assistance to OEMs with the testing and certification process, if required. 5.1. Important Notice Because of the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless and its affiliates accept no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data. 5.2. Safety and Hazards Do not operate your MC7354B modem:
In areas where blasting is in progress Where explosive atmospheres may be present including refuelling points, fuel depots, and chemical plants Near medical equipment, life support equipment, or any equipment which may be susceptible to any form of radio interference. In such areas, the MC7354B modem MUST BE POWERED OFF. Otherwise, the MC7354B modem can transmit signals that could interfere with this equipment. In an aircraft, the MC7354B modem MUST BE POWERED OFF. Otherwise, the MC7354B modem can transmit signals that could interfere with various onboard systems and may be dangerous to the operation of the aircraft or disrupt the cellular network. Use of a cellular phone in an aircraft is illegal in some jurisdictions. Failure to observe this instruction may lead to suspension or denial of cellular telephone services to the offender, or legal action or both. 4117529 Rev 1.0 June 12, 2015 14 Hardware Integration Guide Regulatory Information Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. The MC7354B modem may be used normally at this time. 5.3. Important Compliance Information for North American Users The MC7354B modem has been granted modular approval for mobile applications. Integrators may use the MC7354B in their final products without additional FCC/IC (Industry Canada) certification if they meet the following conditions. Otherwise, additional FCC/IC approvals must be obtained. 1. 2. At least 20cm separation distance between the antenna and the users body must be maintained at all times. To comply with FCC/IC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum antenna gain including cable loss in a mobile-only exposure condition must not exceed:
4.0 dBi in Cellular band 3.0 dBi in PCS band 3.0 dBi in LTE Band 2 4.0 dBi in LTE Band 4 4.0 dBi in LTE Band 5 4.0 dBi in LTE Band 13 4.0 dBi in LTE Band 17 3.0 dBi in LTE Band 25 4.0 dBi in LTE Band 26 3. The MC7354B may transmit simultaneously with other collocated radio transmitters within a host device, provided the following conditions are met:
Each collocated radio transmitter has been certified by FCC / IC for mobile application. At least 20 cm separation distance between the antennas of the collocated transmitters and the users body must be maintained at all times. The output power and antenna gain must not exceed the limits and configurations stipulated in the following table. Device Technology Band Frequency
(MHz) Maximum Antenna Gain Maximum Conducted Power MC7354B Module LTE UMTS CDMA GSM 2 4 5 13 17 25 26 2 4 5 BC0 BC1 BC10 1850 1910 1710 1755 824 849 777 787 704 716 1850 1915 814 849 1850 1910 1710 1755 824 849 824 849 1850 1910 817 824 GSM 850 824 849 PCS 1900 1850 1910 3.0 4.0 4.0 4.0 4.0 3.0 4.0 3.0 4.0 4.0 4.0 3.0 4.0 4.0 3.0
+23 dBm 1 dB
+23 dBm 1 dB
+23 dBm 1 dB
+23 dBm 1 dB
+23 dBm 1 dB
+23 dBm 1 dB
+23 dBm 1 dB
+23 dBm 1 dB
+23 dBm 1 dB
+23 dBm 1 dB
+24 dBm +0.5/-1 dB
+24 dBm +0.5/-1 dB
+24 dBm +0.5/-1 dB
+32 dBm 1 dB
+29 dBm 1 dB 4117529 Rev 1.0 June 12, 2015 15 Hardware Integration Guide Regulatory Information Device Technology Band Frequency
(MHz) Maximum Antenna Gain Maximum Conducted Power WLAN Collocated transmitters*
WiMAX BT 2400 2500 5150 580 2300 2400 2500 2700 3300 3800 2400 2500 5.0 5.0 5.0 5.0 5.0 5.0 29 29 29 29 29 15 Valid collocated Transmitter combinations: WLAN+BT; WiMAX+BT.(WLAN+WiMAX+BT is not permitted.)
*
4. A label must be affixed to the outside of the end product into which the AirPrime MC7354B device is incorporated, with a statement similar to the following:
This device contains FCC ID: N7NMC7354B Contains transmitter module IC: 2417C-MC7354B where 2417C-MC7354B is the modules certification number 5. A user manual with the end product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC/IC RF exposure guidelines. The end product with an embedded AirPrime MC7354B device may also need to pass the FCC Part 15 unintentional emission testing requirements and be properly authorized. Note:
If this module is intended for use in a portable device, you are responsible for separate approval to satisfy the SAR requirements of FCC Part 2.1093 and IC RSS-102. 4117529 Rev 1.0 June 12, 2015 16 6. References 6.1. Reference Documents
[1] AirPrime MC7354B Product Technical Specification and Customer Design Guidelines Reference: TBD
[2] AirPrime MC Series Development Kit Quick Start Guide Reference: 2130705 6.2. List of Abbreviations Abbreviation Definition AC ADC A/D AF AT AUX CAN CB CEP CLK Alternative Current Analog to Digital Converter Analog to Digital conversion Audio-Frequency Attention (prefix for modem commands) Auxiliary Controller Area Network Cell Broadcast Circular Error Probable Clock CMOS Complementary Metal Oxide Semiconductor CS CTS DAC dB DC DCD DCE DCS DR DSR DTE DTR EDGE EFR E-GSM EGPRS EMC EMI Coding Scheme Clear To Send Digital to Analogue Converter Decibel Direct Current Data Carrier Detect Data Communication Equipment Digital Cellular System Dynamic Range Data Set Ready Data Terminal Equipment Data Terminal Ready Enhance Data rates for GSM Evolution Enhanced Full Rate Extended GSM Enhance GPRS Electromagnetic Compatibility Electromagnetic Interference 4117529 Rev 1.0 June 12, 2015 17 Hardware Integration Guide Abbreviation Definition References EMS EN ESD FIFO FR FTA GND GPI GPC GPIO GPO GPRS GPS GSM HR I/O LED LGA LNA MAX MIC MIN MMS MO MT na NC NF NMEA NOM NTC PA Pa Enhanced Message Service Enable Electrostatic Discharges First In First Out Full Rate Full Type Approval Ground General Purpose Input General Purpose Connector General Purpose Input Output General Purpose Output General Packet Radio Service Global Positioning System Global System for Mobile communications Half Rate Input / Output Light Emitting Diode Land Grid Array Low Noise Amplifier Maximum Microphone Minimum MultiMedia Message Service Mobile Originated Mobile Terminated Not Applicable Not Connected Noise Factor National Marine Electronics Association Nominal Negative Temperature Coefficient Power Amplifier Pascal (for speaker sound pressure measurements) PBCCH Packet Broadcast Control Channel PC PCB PDA PFM PSM PWM RAM RF RFI Personal Computer Printed Circuit Board Personal Digital Assistant Power Frequency Modulation Phase Shift Modulation Pulse Width Modulation Random Access Memory Radio Frequency Radio Frequency Interference RHCP Right Hand Circular Polarization 4117529 Rev 1.0 June 12, 2015 18 Hardware Integration Guide Abbreviation Definition References Ring Indicator Reset Real Time Clock Radio Technical Commission for Maritime services Request To Send Receive Serial Clock Serial Data Subscriber Identification Module Short Message Service Serial Peripheral Interface Sound Pressure Level Speaker Static RAM To Be Confirmed Time Division Multiple Access Test Point Transient Voltage Suppressor Transmit Typical Universal Asynchronous Receiver-Transmitter Universal Serial Bus Unstructured Supplementary Services Data Voltage Standing Wave Ratio RI RST RTC RTCM RTS RX SCL SDA SIM SMS SPI SPL SPK SRAM TBC TDMA TP TVS TX TYP UART USB USSD VSWR 4117529 Rev 1.0 June 12, 2015 19