AirPrime EM7700 Hardware Integration Guide 4112206 Rev 2 Important Notice Safety and Hazards Limitation of Liability Preface Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data. Do not operate the Sierra Wireless modem in areas where blasting is in progress, where explosive atmospheres may be present, near medical equipment, near life support equipment, or any equipment which may be susceptible to any form of radio interference. In such areas, the Sierra Wireless modem MUST BE POWERED OFF. The Sierra Wireless modem can transmit signals that could interfere with this equipment. Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE POWERED OFF. When operating, the Sierra Wireless modem can transmit signals that could interfere with various onboard systems. Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. Sierra Wireless modems may be used at this time. The driver or operator of any vehicle should not operate the Sierra Wireless modem while in control of a vehicle. Doing so will detract from the driver or operator's control and operation of that vehicle. In some states and provinces, operating such communications devices while in control of a vehicle is an offence. The information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY. Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability arising under or in connection with the Sierra Wireless product, regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the Sierra Wireless product. Rev 2 Apr.12 Proprietary and Confidential 3 AirPrime EM7700 Hardware Integration Guide Patents Copyright Trademarks This product may contain technology developed by or for Sierra Wireless Inc. This product includes technology licensed from QUALCOMM. This product is manufactured or sold by Sierra Wireless Inc. or its affiliates under one or more patents licensed from InterDigital Group. 2012 Sierra Wireless. All rights reserved. Sierra Wireless, AirPrime, Watcher, and the Sierra Wireless logo are trademarks of Sierra Wireless. Windows is a registered trademark of Microsoft Corporation. Other trademarks are the property of their respective owners. Contact Information Sales Desk:
Post:
Fax:
Web:
1-604-232-1488 8:00 AM to 5:00 PM Pacific Time sales@sierrawireless.com Phone:
Hours:
E-mail:
Sierra Wireless 13811 Wireless Way Richmond, BC Canada V6V 3A4 1-604-231-1109 www.sierrawireless.com Consult our website for up-to-date product descriptions, documentation, application notes, firmware upgrades, troubleshooting tips, and press releases:
www.sierrawireless.com Revision History Revision number Release date Changes 1 2 4 April 2012 April 2012
FCC submission Updated gain values in Regulatory section Proprietary and Confidential 4112206 Contents Introduction . 7 The Universal Development Kit . 7 Required connectors . 8 Power Interface . 9 Overview of operation . 9 Power signals . 9 Module power states . 10 RF Integration . 11 RF connection . 11 Ground connection. 12 Shielding . 12 Antenna and cabling . 12 Interference and sensitivity. 13 Methods to mitigate decreased Rx performance . 13 Radiated Spurious Emissions (RSE) . 14 Radiated sensitivity measurement . 14 Power supply noise . 14 Interference from other wireless devices . 14 Host-generated RF interference . 15 Device-generated RF interference . 15 Regulatory Information . 17 Important notice . 17 Safety and hazards . 17 Important compliance information for North American users . 18 Acronyms and Definitions . 21 Index . 23 Rev 2 Apr.12 Proprietary and Confidential 5 AirPrime EM7700 Hardware Integration Guide 6 Proprietary and Confidential 4112206 1: Introduction 1 Note: An understanding of network technology, and experience in integrating hardware components into electronic equipment is assumed. Sierra Wireless AirPrime Intelligent Embedded Modules form the radio component for the products in which they are embedded. The AirPrime EM7700 is available for use on LTE and HSPA+
networks. Purpose of this guide This guide addresses issues that affect the integration of AirPrime embedded modules into host products, and includes design recommendations for the host products. The Universal Development Kit A hardware development platform is available from Sierra Wireless for evaluating and developing with the EM7700. The Universal Development Kit (UDK) (for AirPrime MC-series modules) and a separate adapter board and RF cable may be ordered to use the UDK with the EM7700. The UDK contains hardware components for evaluating and developing with the module, including:
Other accessories Development board Cables Antennas (Band 17 is not supported by supplied antennas) Documentation suite For instructions on setting up the UDK, see PCI Express Mini Card Dev Kit Quick Start Guide (Document 2130705). For over-the-air LTE testing, ensure that suitable antennas are used.
(Two antennas are required for this testing; Sierra Wireless offers an LTE-capable antenna covering 7002600 MHz BWplease order part number 6000492 (Qty 1this contains two antennas).) Rev 2 Apr.12 Proprietary and Confidential 7 AirPrime EM7700 Hardware Integration Guide Required connectors Table 1-1 describes the connectors used to integrate the EM7700 Module into your host device. Table 1-1: Required host-module connectorsa Connector type Description RF cables FPC (70-pin) SIM
Mate with I-PEX MHF-A13 connectors
Two connector jacks
Hirose Flexible Printed Circuit (FPC) connector FH29BJ-70S-0.2SHW(05) Industry-standard connector. Type depends on how host device exposes the SIM socket Example: UDK board uses ITT CCM03-3518 a. Manufacturers/part numbers are for reference only and are subject to change. Choose connectors that are appropriate for your own design. 8 Proprietary and Confidential 4112206 2: Power Interface 22 Overview of operation AirPrime embedded modules are designed to use a 3.7V (nominal) power supply provided by the host. It is the hosts responsibility to provide safe and continuous power to the module at all times; the module does NOT have an independent power supply, or protection circuits to guard against electrical issues. The modules power state is controlled by the hosts assertion/
deassertion of POWER_ON and RESET_N. The module also monitors its supply voltage and requests shutdown if the supply is insufficient. Power signals The module must be connected to a 3.7V power supply. For detailed pinout and voltage/current requirements of this module, see the AirPrime EM7700 Product Technical Specification Document
& Customer Design Guidelines. Rev 2 Apr.12 Proprietary and Confidential 9 AirPrime EM7700 Hardware Integration Guide Module power states The module has five power states, as described in Table 2-1. Table 2-1: Module power states State Details d e r e w o p s i e l u d o M d e r e w o p s i t s o H e v i t c a e c a f r e t n i B S U d e l b a n e F R Module is active Default state. Occurs when VCC is first applied, POWER_ON is asserted (pulled high), and WWAN_DISABLE_N is deasserted Module is capable of placing/receiving calls, or establishing data connections on the wireless network Current consumption is affected by several factors, including:
Radio band being used
Transmit power
Receive gain settings
Data rate Module is active State is controlled by host interface using software commands:
+CFUN=0 ([1] AT Command Set for User Equipment (UE) (Release 6)
(Doc# 3GPP TS 27.007))) Normal
(Default state) Low power
(Airplane mode) Sleep Off
Normal state of module between calls or data connections Module cycles between wake (polling the network) and sleep, at network provider-
determined interval. Host keeps module powered off by deasserting POWER_ON (signal left floating or tied low) Module draws minimal current Disconnected Host power source is disconnected from the module and all voltages associated with the module are at 0 V. 10 Proprietary and Confidential 4112206 3: RF Integration 3 The AirPrime EM7700 operates on the frequency bands listed below. Table 3-1: LTE frequency band support Band Frequencies Band 4 (AWS) Band 17 Tx: 17101755 MHz Rx: 21102155 MHz Tx: 704716 MHz Rx: 734746 MHz Table 3-2: HSPA+ frequency band supporta Band Frequencies Band 1 WCDMA 2100 Band 2 WCDMA 1900 Band 5 WCDMA 850 Tx: 19201980 MHz Rx: 21102170 MHz Tx: 18501910 MHz Rx: 19301990 MHz Tx: 824849 MHz Rx: 869894 MHz a. WCDMA channel spacing is 5 MHz, but this can be adjusted to optimize performance in a particular deployment scenario. Table 3-3: GPS frequency band support Band Frequencies GNSS
(wide band GPS and GLONASS) 15651606 MHz GPS
(narrow band GPS) 1575.42 MHz RF connection When attaching antennas to the module:
Use I-PEX connectors (model I-PEX MHF-A13) to attach antennas to the modules connection points.
Match coaxial connections between the module and the antenna to 50 .
Minimize RF cable losses to the antenna; the recommended
maximum cable loss for antenna cabling is 0.5 dB. To ensure best thermal performance, if possible use the mounting holes to attach (ground) the device to a metal chassis. Rev 2 Apr.12 Proprietary and Confidential 11 AirPrime EM7700 Hardware Integration Guide Note: If the antenna connection is shorted or open, the modem will not sustain permanent damage. Ground connection When connecting the module to system ground:
Prevent noise leakage by establishing a very good ground connection to the module through the host connector. Connect to system ground using the three mounting holes at the top and bottom of the module.
Minimize ground noise leakage into the RF. Depending on the host board design, noise could potentially be coupled to the module from the host board. This is mainly an issue for host designs that have signals traveling along the length of the module, or circuitry operating at both ends of the module interconnects. Shielding The module is fully shielded to protect against EMI and must not be removed. Antenna and cabling When selecting the antenna and cable, it is critical to RF performance to match antenna gain and cable loss. Choosing the correct antenna and cabling When matching antennas and cabling:
The antenna (and associated circuitry) should have a nominal impedance of 50 with a return loss of better than 10 dB across each frequency band of operation. The system gain value affects both radiated power and regulatory (FCC, IC, CE, etc.) test results. Designing custom antennas Consider the following points when designing custom antennas:
A skilled RF engineer should do the development to ensure that the RF performance is maintained. If both UMTS and CDMA modules will be installed in the same platform, you may want to develop separate antennas for maximum performance.
12 Proprietary and Confidential 4112206 RF Integration Determining the antennas location When deciding where to put the antennas:
Antenna location may affect RF performance. Although the module is shielded to prevent interference in most applications, the placement of the antenna is still very importantif the host device is insufficiently shielded, high levels of broadband or spurious noise can degrade the modules perfor-
mance. Connecting cables between the module and the antenna must have 50 impedance. If the impedance of the module is mismatched, RF performance is reduced significantly. Antenna cables should be routed, if possible, away from noise sources
(switching power supplies, LCD assemblies, etc.). If the cables are near the noise sources, the noise may be coupled into the RF cable and into the antenna.
Disabling the diversity antenna
Use the AT command !RXDEN=0 to disable receive diversity or !RXDEN=1 to enable receive diversity. Note: A diversity antenna is used to improve connection quality and reliability through redundancy. Because two antennas may experience difference interference effects (signal distortion, delay, etc.), when one antenna receives a degraded signal, the other may not be similarly affected. Interference and sensitivity Several sources of interference can affect the RF performance of the module
(RF desense). Common sources include power supply noise and device-
generated RF. RF desense can be addressed through a combination of mitigation techniques
(Methods to mitigate decreased Rx performance on page 13) and radiated sensitivity measurement (Radiated sensitivity measurement on page 14). Note: The EM7700 is based on ZIF (Zero Intermediate Frequency) technologies. When performing EMC (Electromagnetic Compatibility) tests, there are no IF (Intermediate Frequency) components from the module to consider. Methods to mitigate decreased Rx performance It is important to investigate sources of localized interference early in the design cycle. To reduce the effect of device-generated RF on Rx performance:
Put the antenna as far as possible from sources of interference. The drawback is that the module may be less convenient to use. Shield the host device. The module itself is well shielded to avoid external interference. However, the antenna cannot be shielded for obvious reasons.
Rev 2 Apr.12 Proprietary and Confidential 13 AirPrime EM7700 Hardware Integration Guide In most instances, it is necessary to employ shielding on the components of the host device (such as the main processor and parallel bus) that have the highest RF emissions. Filter out unwanted high-order harmonic energy by using discrete filtering on low frequency lines. Form shielding layers around high-speed clock traces by using multi-layer PCBs. Route antenna cables away from noise sources.
Radiated Spurious Emissions (RSE) When designing an antenna for use with AirPrime embedded modules, the host device with an AirPrime embedded module must satisfy the radiated spurious emission (RSE) test cases described in:
CE/ETSI EN 301 908 (WCDMA), test numbers 5.3.1 (Radiated Emissions
(UE)) Note that antenna impedance affects radiated emissions, which must be compared against the conducted 50-ohm emissions baseline. (AirPrime embedded modules meet the 50-ohm conducted emissions requirement.) Radiated sensitivity measurement A wireless host device contains many noise sources that contribute to a reduction in Rx performance. To determine the extent of any receiver performance desensitization due to self-
generated noise in the host device, over-the-air (OTA) or radiated testing is required. This testing can be performed by Sierra Wireless or you can use your own OTA test chamber for in-house testing. Power supply noise Noise in the power supply can lead to noise in the RF signal. The power supply ripple limit for the module is no more than 100 mVp-p 1 Hz to 100 kHz. This limit includes voltage ripple due to transmitter burst activity. Additional decoupling capacitors can be added to the main VCC line to filter noise into the device. Interference from other wireless devices Wireless devices operating inside the host device can cause interference that affects the module. To determine the most suitable locations for antennas on your host device, evaluate each wireless devices radio system, considering the following:
Any harmonics, sub-harmonics, or cross-products of signals generated by wireless devices that fall in the modules Rx range may cause spurious response, resulting in decreased Rx performance. 14 Proprietary and Confidential 4112206 RF Integration
The Tx power and corresponding broadband noise of other wireless devices may overload or increase the noise floor of the modules receiver, resulting in Rx desense. The severity of this interference depends on the closeness of the other antennas to the modules antenna. To determine suitable locations for each wireless devices antenna, thoroughly evaluate your host devices design. Host-generated RF interference All electronic computing devices generate RF interference that can negatively affect the receive sensitivity of the module. Proximity of host electronics to the antenna in wireless devices can contribute to decreased Rx performance. Components that are most likely to cause this include:
Microprocessor and memory
Display panel and display drivers Switching-mode power supplies Device-generated RF interference The module can cause interference with other devices. Wireless devices such as AirPrime embedded modules transmit in bursts (pulse transients) for set durations
(RF burst frequencies). Hearing aids and speakers convert these burst frequencies into audible frequencies, resulting in audible noise. Rev 2 Apr.12 Proprietary and Confidential 15 AirPrime EM7700 Hardware Integration Guide 16 Proprietary and Confidential 4112206 A: Regulatory Information A This module is designed to and, upon commercial release, will be certified to meet carrier requirements (e.g. AT&T). Upon commercial release, the following regulatory approvals will have been attained:
FCC Upon commercial release, the following industry approvals will have been obtained:
PTCRB Additional approvals may be obtained upon customer request contact your Sierra Wireless account representative for details. Additional testing and certification may be required for the end product with an embedded EM7700 modem and are the responsibility of the OEM. Sierra Wireless offers professional services-based assistance to OEMs with the testing and certification process, if required. Important notice Because of the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-
constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless and its affiliates accept no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data. Safety and hazards Do not operate your EM7700 modem:
Where explosive atmospheres may be present including In areas where blasting is in progress
refuelling points, fuel depots, and chemical plants Near medical equipment, life support equipment, or any equipment which may be susceptible to any form of radio inter-
ference. In such areas, the EM7700 modem MUST BE POWERED OFF. Otherwise, the EM7700 modem can transmit signals that could interfere with this equipment. Rev 2 Apr.12 Proprietary and Confidential 17 AirPrime EM7700 Hardware Integration Guide In an aircraft, the EM7700 modem MUST BE POWERED OFF. Otherwise, the EM7700 modem can transmit signals that could interfere with various onboard systems and may be dangerous to the operation of the aircraft or disrupt the cellular network. Use of a cellular phone in an aircraft is illegal in some jurisdictions. Failure to observe this instruction may lead to suspension or denial of cellular telephone services to the offender, or legal action or both. Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. The EM7700 modem may be used normally at this time. Important compliance information for North American users Note: Details are preliminary and subject to change. The EM7700 modem has been granted modular approval for mobile applications. Integrators may use the EM7700 modem in their final products without additional FCC certification if they meet the following conditions. Otherwise, additional FCC approvals must be obtained. 1. At least 20 cm separation distance between the EM7700 antenna and the users body must be maintained at all times. 2. To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, the maximum antenna gain including cable loss for standalone transmission in mobile exposure condition must not exceed:
9.5 dBi in Cellular band 9 dBi in PCS band 6.0 dBi in LTE Band 4 9.0 dBi in LTE Band 17 3. The EM7700 modem may transmit simultaneously with other co-located radio transmitters within a host device, provided the following conditions are met:
Each co-located radio transmitter has been certified by FCC for mobile application. At least 20 cm separation distance between the antennas of the co-located transmitters and the users body must be maintained at all times. The output power and antenna gain must not exceed the limits and configu-
rates stipulated in the following table. 18 Proprietary and Confidential 4112206 Device Technology Frequency
(MHz) Maximum Conducted Power (dBm) EM7700 module Co-located transmittersa UMTS UMTS LTE LTE WLAN WLAN WiMAX WiMAX WiMAX BT 824849 18501910 704716 17101755 24002500 51505850 23002400 25002700 33003800 24002500 24 24 24 24 29 29 29 29 29 15 Maximum Antenna Gain
(dBi) 6.5 9.0 6.0 6.0 5.0 5.0 5.0 5.0 5.0 5.0 a. Valid co-located transmitter combinations: WLAN+BT; WiMAX+BT. WLAN+WiMAX+BT is not permitted. 4. A label must be affixed to the outside of the end product into which the EM7700 modem is incorporated, with a statement similar to the following:
This device contains FCC ID: N7NEM7700 5. A user manual with the end product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC RF exposure guidelines. The end product with an embedded EM7700 modem may also need to pass the FCC Part 15 unintentional emission testing requirements and be properly authorized per FCC Part 15. Note: If this module is intended for use in a portable device, you are responsible for separate approval to satisfy the SAR requirements of FCC Part 2.1093. Rev 2 Apr.12 Proprietary and Confidential 19 AirPrime EM7700 Hardware Integration Guide 20 Proprietary and Confidential 4112206 B: Acronyms and Definitions
. Table B-1: Acronyms and definitions Acronym or term Definition B AGC BER BLER Call Box CDMA dB dBm DUT EDGE EM ESD FER GPRS GPS GSM Hz Automatic Gain Control Bit Error Rate - a measure of receive sensitivity Block Error Rate Base Station Simulator - Agilent E8285A or 8960, Rohde & Schwarz CMU200 Code Division Multiple Access Decibel = 10 x log10 (P1/P2) P1 is calculated power; P2 is reference power Decibel = 20 x log10 (V1/V2) V1 is calculated voltage, V2 is reference voltage Decibels, relative to 1 mW - Decibel(mW) = 10 x log10 (Pwr (mW)/1mW) Device Under Test Enhanced Data rates for GSM Evolution Embedded Module ElectroStatic Discharge Frame Error Rate - a measure of receive sensitivity General Packet Radio Services Global Positioning System Global System for Mobile communications Hertz = 1 cycle/second inrush current Peak current drawn when a device is connected or powered on IS-2000 IS-95 LDO MC5728V MC57xx MC8700/MC8704/
MC8705/MC8790/
MC8790V/MC8791V/
MC8792V/MC8795V/
MC8801 3G radio standards for voice and data (CDMA only) 2G radio standards targeted for voice (cdmaONE) Low Drop Out - refers to linear regulator Sierra Wireless AirPrime embedded modules used on CDMA networks Any of the following CDMA AirPrime embedded modules: MC5728V Sierra Wireless AirPrime embedded modules used on GSM/UMTS networks Rev 2 Apr.12 Proprietary and Confidential 21 AirPrime EM7700 Hardware Integration Guide Table B-1: Acronyms and definitions Acronym or term Definition MC8xxx MHz MIO MPE OTA PCS RF RMS SA Any of the following GSM/UMTS AirPrime embedded modules: MC8700/
MC8704/MC8705/MC8790/MC8790V/MC8791V/MC8792V/MC8795V/
MC8801 MegaHertz = 10E6 Hertz (Hertz = 1 cycle/second) Module Input/Output Maximum Permissible Exposurethe level of radiation to which a person may be exposed without hazardous effect or adverse biological changes Over-The-Air or Radiated through the antenna Personal Communication System - PCS spans the 1.9 GHz radio spectrum Radio Frequency Root Mean Square Selective Availability Sensitivity (Audio) Measure of lowest power signal that the receiver can measure Sensitivity (RF) Measure of lowest power signal at the receiver input that can provide a prescribed BER/BLER/SNR value at the receiver output. SIM SNR SOF UART UDK UMTS USB USIM VCC WCDMA XIM Subscriber Identity Module Signal to Noise Ratio Start of Frame - a USB function Universal Asynchronous Receiver Transmitter Universal Development Kit (PCI Express Mini Card Dev Kit) Universal Mobile Telecommunications System Universal Serial Bus Universal Subscriber Identity Module Supply voltage (3.3 V for these devices) Wideband Code Division Multiple AccessIn this document, the term UMTS is used instead of WCDMA. In this document, XIM is used as part of the contact identifiers for the USIM interface (XIM_VCC, XIM_CLK, etc.). 22 Proprietary and Confidential 4112206 Index A acronyms and definitions, 21 22 antenna connection considerations, 11 custom, considerations, 12 diversity antenna, disabling, 13 limit, matching coaxial connections, 11 location, considerations, 13 matching, considerations, 12 maximum cable loss, 11 B bands supported, RF HSPA+, 11 LTE, 11 C cable loss antenna, maximum, 11 connection grounding, 12 connectors, required host-module, 8 D desense. See RF diversity antenna disabling, 13 F FCC approval, 17 filtering, RF desense, 14 FPC connector, required, 8 frequency band support GPS, 11 HSPA+, 11 LTE, 11 G gain GPS maximum, 18 frequency band support, 11 grounding connection considerations, 12 H HSPA+
frequency band support, 11 I impedance module-antenna, 13 interference device generated, 15 host-generated, 15 power supply noise, 14 wireless devices, 14 L LTE frequency band support, 11 M module power states, 10 N noise leakage, minimizing, 12 RF interference, power supply, 14 P PCB multi-layer, shielding for RF desense, 14 power required supply voltage, 9 signals, overview, 9 states, module, 10 supply, RF interference, 14 supply, ripple limit, 14 power interface, 9 10 PTCRB approval, 17 R radiated sensitivity measurement, 14 radiated spurious emissions, 14 regulatory information, 17 19 FCC, 18 limitation of liability, 17 safety and hazards, 17 Rev 2 Apr.12 Proprietary and Confidential 23 Document SubTitle RF antenna cable loss, maximum, 11 antenna connection, considerations, 11 connectors, required, 8 desense device-generated, 15 harmonic energy, filtering, 14 mitigation suggestions, 13 shielding suggestions, 13 integration, 11 15 interference other devices, 15 power supply, 14 wireless devices, 14 RF bands supported HSPA+, 11 LTE, 11 RSE, 14 S sensitivity radiated measurement, overview, 14 shielding module, compliance, 12 reducing RF desense, 13 SIM connector, required, 8 U UDK (Universal Development Kit) components, included, 7 Universal Development Kit (UDK) components, included, 7 Z ZIF (Zero Intermediate Frequency), 13 24 Proprietary and Confidential 4112206