FCC ID: QOQWT11U WT11U long range Bluetooth 2.1+EDR module

WT11u DATA SHEET Monday, 21 November 2016 Version 0.9.2 VERSION HISTORY Version Comment 0.8 0.81 0.9 0.9.1 0.9.2 Initial versions Ordering information updated Reformatted tables, many WT11i->WT11u updates Rest of tables reformatted Updated dimension drawings Silicon Laboratories Finland Oy TABLE OF CONTENTS 1 Ordering Information......................................................................................................................................6 2 Pinout and Terminal Description ...................................................................................................................7 3 Electrical Characteristics ............................................................................................................................ 10 3.1 Absolute Maximum Ratings ................................................................................................................ 10 3.2 Recommended Operating Conditions ................................................................................................. 10 3.3 Input / Output Terminal Characteristics .............................................................................................. 11 3.3.1 3.3.2 Input/Output Terminal Characteristics (Digital) ............................................................................ 11 Input/Output Terminal Characteristics (USB) .............................................................................. 12 3.4 3.5 PIO Current Sink and Source Capability ............................................................................................. 13 Transmitter Performance For BDR ..................................................................................................... 14 3.6 Receiver Performance ........................................................................................................................ 14 3.7 Current Consumption .......................................................................................................................... 15 3.8 WT11u-A Antenna Specification ......................................................................................................... 16 4 Physical Dimensions .................................................................................................................................. 19 4.1 Package Drawings .............................................................................................................................. 21 5 Layout Guidelines ....................................................................................................................................... 23 6 UART Interface ........................................................................................................................................... 26 6.1 UART Bypass ...................................................................................................................................... 28 6.2 UART Configuration While Reset is Active ......................................................................................... 28 6.3 UART Bypass Mode ............................................................................................................................ 28 7 USB Interface ............................................................................................................................................. 29 7.1 USB Data Connections ....................................................................................................................... 29 7.2 USB Pull-Up resistor ........................................................................................................................... 29 7.3 USB Power Supply .............................................................................................................................. 29 7.4 7.5 Self-Powered Mode ............................................................................................................................. 29 Bus-Powered Mode ............................................................................................................................. 30 7.6 USB Suspend Current ......................................................................................................................... 31 7.7 USB Detach and Wake-Up Signaling.................................................................................................. 31 7.8 USB Driver .......................................................................................................................................... 32 7.9 USB v2.0 Compliance and Compatibility ............................................................................................ 32 8 Serial Peripheral Interface (SPI) ................................................................................................................. 33 9 PCM Codec Interface ................................................................................................................................. 34 9.1 9.2 9.3 PCM Interface Master/Slave ............................................................................................................... 34 Long Frame Sync ................................................................................................................................ 35 Short Frame Sync ............................................................................................................................... 35 9.4 Multi-slot Operation ............................................................................................................................. 36 9.5 GCI Interface ....................................................................................................................................... 36 Silicon Laboratories Finland Oy 9.6 9.7 9.8 9.9 Slots and Sample Formats .................................................................................................................. 37 Additional Features ............................................................................................................................. 38 PCM_CLK and PCM_SYNC Generation ............................................................................................ 38 PCM Configuration .............................................................................................................................. 39 10 I/O Parallel Ports ..................................................................................................................................... 42 10.1 PIO Defaults ................................................................................................................................. 42 11 Reset ....................................................................................................................................................... 43 11.1 Pin States on Reset ..................................................................................................................... 44 12 Certifications ........................................................................................................................................... 45 12.1 12.2 Bluetooth ...................................................................................................................................... 45 FCC and IC .................................................................................... Error! Bookmark not defined. 12.2.1 FCC et IC ....................................................................................... Error! Bookmark not defined. 12.3 12.4 12.5 12.6 12.7 12.8 CE ................................................................................................................................................ 48 MIC Japan .................................................................................................................................... 48 KCC (Korea)................................................................................................................................. 48 Anatel ........................................................................................................................................... 49 Qualified Antenna Types for WT11u-E ........................................................................................ 50 Moisture Sensitivity Level (MSL).................................................................................................. 50 Silicon Laboratories Finland Oy KEY FEATURES:

Radio features:

Bluetooth v.2.1 + EDR Bluetooth class 1 radio Transmit power: +17 dBm Receiver sensitivity: -84 dBm (DH5) Range: 350 meters line-of-sight Integrated chip antenna or U.FL connector Hardware features:

UART and USB host interfaces 802.11 co-existence interface 6 software programmable IO pins Operating voltage: 2.7V to 3.6V Temperature range: -40C to +85C Dimensions: 35.75 x 14.50 x 2.6 mm Qualifications:

Bluetooth CE FCC IC Japan PHYSICAL OUTLOOK WT11u Bluetooth Module DESCRIPTION 1 to class design module WT11u is a fully integrated Bluetooth 2.1 +

EDR, combining antenna, Bluetooth radio and an on-board iWRAP Bluetooth stack. Silicon Labs WT11u provides an ideal solution for developers that want to quickly integrate long range and high performance Bluetooth wireless without technology their into Bluetooth radio investing several months and stack development. WT11u provides a 100dB link budget ensuring long rage and robust Bluetooth connectivity. WT11u uses Silicon Labs iWRAP Bluetooth stack, which is an embedded Bluetooth stack implementing 13 different Bluetooth profiles and Apple iAP connectivity. By using WT11u combined with iWRAP Bluetooth stack and Silicon Labs excellent technical support designers ensure quick time to market, low development costs and risk. APPLICATIONS:

Industrial and M2M Point-of-Sale devices Computer Accessories Silicon Laboratories Finland Oy 1 Ordering Information Firmware U.FL Connector Internal chip antenna iWRAP 5.6 firmware, reel WT11u-E-AI56 iWRAP 5.5 firmware, reel WT11u-E-AI55 WT11u-A-AI56 WT11u-A-AI55 HCI firmware, BT2.1 + EDR, reel WT11u-E-HCI21001 WT11u-A-HCI21001 iWRAP 5.6 firmware with iAP, reel WT11u-E-AI56IAP WT11u-A-AI56IAP iWRAP 5.6 firmware, cut reel WT11u-E-AI56C WT11u-A-AI56C iWRAP 5.5 firmware, cut reel WT11u-E-AI55C WT11u-A-AI55C HCI firmware, BT2.1 + EDR, cut reel WT11u-E-HCI21001C WT11u-A-HCI21001C iWRAP 5.6 firmware with iAP, cut reel WT11u-E-AI56IAPC WT11u-A-AI56IAPC Table 1: Ordering information Silicon Laboratories Finland Oy Page 6 of 51 Pinout and Terminal Description 2 Figure 1: WT11u connection diagram Pad name Pad number Pad type Description RESET 17 Input Reset input, active high, internal 220kohm pull-down. Keep high for >5ms for reset GND 1, 14, 15, 28 GND Ground connection, connect all to a ground plane with minimal trace lengths VDD_PA VDD 2 16 Supply voltage Supply voltage for RF power amplifier Supply voltage Chipset supply voltage Table 2: Supply and RF Terminal Descriptions Silicon Laboratories Finland Oy Page 7 of 51 WT11iGNDVDD_PAPIO2PIO3UART_RTS#UART_RXPCM_OUTUSB+USB-UART_CTS#PCM_INPCM_CLKPCM_SYNCGNDGNDAIOUART_TXPIO5SPI_MOSISPI_MISOSPI_CLKSPI_CS#PIO4PIO7PIO6RESETVDDGND12345678910111213142827262524232221201918171615 PIO signal Pad number Description PIO[2]

PIO[3]

PIO[4]

PIO[5]

PIO[6]

PIO[7]

3 4 20 25 18 19 Bi-directional digital in/out with programmable strength and pull-up/pull-

down Bi-directional digital in/out with programmable strength and pull-up/pull-

down Bi-directional digital in/out with programmable strength and pull-up/pull-

down Bi-directional digital in/out with programmable strength and pull-up/pull-

down Bi-directional digital in/out with programmable strength and pull-up/pull-

down Bi-directional digital in/out with programmable strength and pull-up/pull-

down AIO[1]

27 Bi-directional analog in/out Table 3: GPIO Terminal Descriptions PCM signal Pad number Pad type Description PCM_OUT PCM_IN PCM_SYNC PCM_CLK 7 11 13 12 Output, weak internal pull-down Synchronous data output Input, weak internal pull-down Synchronous data input Bi-directional, weak internal pull-down Synchronous data sync Bi-directional, weak internal pull-down Synchronous data clock Table 4: PCM Terminal Descriptions Silicon Laboratories Finland Oy Page 8 of 51 UART signal Pad number Pad type Description UART_TX UART_RTS#

UART_RX UART_CTS#

26 5 6 10 Output, weak pull-up internal UART data output, active high Output, weak pull-up internal UART request to send, active low Input, weak internal pull-

down UART data input, active high Input, weak internal pull-

down UART clear active low to send, Table 5: UART Terminal Descriptions USB signal Pad number Pad type Description USB+

USB-

8 9 Bidirectional USB data line with internal 1.5kohm pull-up Bidirectional USB data line Table 6: USB Terminal Descriptions SPI signal Pad number SPI_MOSI SPI_CS#

SPI_CLK SPI_MISO 24 21 22 23 Pad type Description Input, weak internal pull-down SPI data input Input, weak internal pull-up Chip select, active low Input, weak internal pull-down SPI clock Output, weak internal pull-down SPI data output Table 7: Terminal Descriptions Silicon Laboratories Finland Oy Page 9 of 51 3 Electrical Characteristics 3.1 Absolute Maximum Ratings Specification Storage temperature VDD_PA, VDD Min

-40

-0.4 85 3.6 Max Unit Other terminal voltages VSS-0.4 VDD+0.4 C V V 3.2 Recommended Operating Conditions Table 8: Absolute Maximum Ratings Specification Operating temperature VDD_PA*, VDD Min Max Unit

-40 3.0 85 3.6 C V

*) VDD_PA has an effect on the RF output power. Table 9: Recommended Operating Conditions Silicon Laboratories Finland Oy Page 10 of 51 3.3 Input / Output Terminal Characteristics 3.3.1 Input/Output Terminal Characteristics (Digital) Digital Terminals Input Voltage Levels VIL input logic level low 2.7 V VDD 3.0 V 1.7 V VDD 1.9 V VIH input logic level high Output Voltage Levels VOL output logic level low

(IO = 4.0 mA) 2.7V VDD 3.0 V VOL output logic level low

(IO = 4.0 mA) 1.7V VDD 1.9 VOL output logic level high

(IO = 4.0 mA) 2.7V VDD 3.0 VOL output logic level high

(IO = 4.0 mA) 1.7V VDD 1.9 Input and Tristate Current with Strong pull-up Strong pull-down Weak pull-up Weak pull-down I/O pad leakage current CI input capacitance Min Typ Max Unit

-0.4

-0.4 0.7 VDD

-

-

VDD - 0.2 VDD - 0.4

-100 10

-5.0 0.2

-1 1.0

-

-

-

-

-

-

-

-40 40

-1.0 1.0 0

-

0.8 0.4 VDD + 0.4 0.2 0.4

-10 100

-0.2 5.0 1 5.0 V V V V V V V A A A A A pF Silicon Laboratories Finland Oy Page 11 of 51 3.3.2 Input/Output Terminal Characteristics (USB) USB Terminals VDD_USB for correct USB operation Input Threshold VIL input logic level log Min 3.1

-

VIH input logic level high 0.7VDD_USB Typ Max Unit

-

-

3.6 0.3VDD_USB

-

V V V Silicon Laboratories Finland Oy Page 12 of 51 3.4 PIO Current Sink and Source Capability Figure 2: WT11u PIO Current Drive Capability Silicon Laboratories Finland Oy Page 13 of 51 3.5 Transmitter Performance For BDR RF characteristic Min Typ Max Bluetooth specification Unit Max transmit power 16 17 18.5

<20 dBm Transmit power variation over temperature range Transmit power variation over supply voltage range Transmit power variation over frequency range TBD TBD TBD Transmit power control range TBD 17 20dB bandwidth for modulated carrier ACP F = F0 2MHz F = F0 3MHz F = F0 > 3MHz Drift rate F1avg F1max F2avg / F1avg TBD

<1000 TBD TBD TBD TBD TBD TBD TBD

-20

-40

-40 25 140 to 175 140 to 175

>=0.8 dB dB dB dB kHz dBc dBc dBc kHz kHz kHz Table 10: Transmitter performance for BDR (room temperature, VDD=3.3V) Figure 3: Typical TX power as a function of VDD_PA TBD 3.6 Receiver Performance Antenna gain not taken into account Silicon Laboratories Finland Oy Page 14 of 51 Characteristic, VDD=3.3V, room temperature Packet type Typ Bluetooth Unit specification DH1 TBD

-70 dBm Sensitivity for 0.1% BER DH5

-85 2-DH1 TBD 2-DH5 TBD 3-DH1 TBD 3-DH5 TBD Sensitivity variation over temperature range TBD dBm dBm dBm dBm dBm dBm 3.7 Current Consumption Operating mode Peak Average Unit Stand-by, page mode 0 TX 3-DH5 TX 2-DH5 TX DH5 RX Deep sleep Inquiry TBD TBD TBD TBD TBD TBD TBD mA mA mA mA mA mA mA Table 11: WT11u Current Consumption Silicon Laboratories Finland Oy Page 15 of 51 3.8 WT11u-A Antenna Specification WT11u-A uses a monopole type on a chip antenna with maximum gain of 0.5 dBi. The radiation pattern and the total radiated efficiency are dependent on the layout and any metal around the antenna has an effect on the radiation characteristics. Typically the efficiency is 30 50%. Figure 4: Antenna radiation pattern in a USB dongle layout Figure 5: Antenna radiation pattern in a USB dongle layout Silicon Laboratories Finland Oy Page 16 of 51 WT11i-A Figure 6: Antenna radiation pattern in a USB dongle layout Figure 7: Antenna radiation pattern in the WT11 evaluation kit Figure 8: Antenna radiation pattern in the WT11 evaluation kit Silicon Laboratories Finland Oy Page 17 of 51 WT11i Figure 9: Antenna radiation pattern in the WT11 evaluation kit Silicon Laboratories Finland Oy Page 18 of 51 4 Physical Dimensions Figure 10: Physical dimensions (top view) Figure 11: Dimensions of WT11u-A Silicon Laboratories Finland Oy Page 19 of 51 Figure 12: Dimensions of WT11u-E Silicon Laboratories Finland Oy Page 20 of 51 4.1 Package Drawings Figure 13: WT11u taping Silicon Laboratories Finland Oy Page 21 of 51 Figure 14: WT11u orientation in the reel Silicon Laboratories Finland Oy Page 22 of 51 5 Layout Guidelines WT11u is pin compatible with WT11i and WT11, despite slightly different external dimensions compared to WT11. For a new design it recommended to follow the land pattern shown in the figure below. Figure 15: Recommended PCB land pattern for WT11u Do not place any copper under the antenna. The minimum recommended keep out area is shown in the Figure 16. Any dielectric material in close proximity to the antenna will effect on the impedance matching of the antenna by lowering the resonance frequency. Figure 17 shows how different FR4 thickness under the antenna effect on the resonance frequency. Recommended PCB thickness for the PCB is 1.6 mm 2.8 mm. Avoid placing plastic cover closer than 3 mm from the antenna as this will also tune the resonance frequency downwards. Silicon Laboratories Finland Oy Page 23 of 51 Figure 16: Recommended metal keep put area for WT11u Figure 17: Effect of FR4 under the antenna to the resonant frequency Use good layout practices to avoid excessive noise coupling to supply voltage traces or sensitive analog signal traces, such as analog audio signals. If using overlapping ground planes use stitching vias separated by max 3 mm to avoid emission from the edges of the PCB. Connect all the GND pins directly to a solid GND plane and make sure that there is a low impedance path for the return current following the signal and supply traces all the way from start to the end. Silicon Laboratories Finland Oy Page 24 of 51 Edge of the PCBDo not place copper or any metal within the area marked with cross linesGND area with stitching viasEffect of PCB thickness to the antenna impedance matching-40-35-30-25-20-15-10-502300235024002450250025502600Freq (MHz)S11 (dB)1 mm2 mm3 mmBT Band A good practice is to dedicate one of the inner layers to a solid GND plane and one of the inner layers to supply voltage planes and traces and route all the signals on top and bottom layers of the PCB. This arrangement will make sure that any return current follows the forward current as close as possible and any loops are minimized. Figure 18: Typical 4-layer PCB construction Figure 19: Use of stitching vias to avoid emissions from the edges of the PCB Silicon Laboratories Finland Oy Page 25 of 51 LayoutSupply voltageIf possible use solid power planeMake sure that solid GND plane follows the traces all the wayDo not route supply voltage traces across separated GND regions so that the path for the return current is cutMIC inputPlace LC filtering and DC coupling capacitors symmetrically as close to audio pins as possiblePlace MIC biasing resistors symmetrically as close to microhone as possible.Make sure that the bias trace does not cross separated GND regions (DGND -> AGND) so that the path for the return current is cut. If this isnot possible the do not separate GND regions but keep one solid GND plane.Keep the trace as short as possibleSignalsGNDPowerSignalsRecommended PCB layer configurationOverlapping GND layers without GND stitching viasOverlapping GND layers with GND stitching vias shielding the RF energy 6 UART Interface This is a standard UART interface for communicating with other serial devices.WT11u UART interface provides a simple mechanism for communicating with other serial devices using the RS232 protocol. Four signals are used to implement the UART function. When WT11u is connected to another digital device, UART_RX and UART_TX transfer data between the two devices. The remaining two signals, UART_CTS and UART_RTS, can be used to implement RS232 hardware flow control where both are active low indicators. All UART connections are implemented using CMOS technology and have signalling levels of 0V and VDD. UART configuration parameters, such as data rate and packet format, are set using WT11u software. Note:

In order to communicate with the UART at its maximum data rate using a standard PC, an accelerated serial port adapter card is required for the PC. Parameter Data rate Possible values Minimum 1200bps (2% error) 9600bps (1% error) Maximum 3Mbps (1% error) Flow control RTS/CTS or None Parity None, Odd or Even Number of stop bits Bits per channel 1 or 2 8 Table 12: Possible UART Settings The UART interface is capable of resetting WT11u upon reception of a break signal. A break is identified by a continuous logic low (0V) on the UART_RX terminal, as shown in Figure 20. If tBRK is longer than the value (in microseconds), defined by PSKEY_HOST_IO_UART_RESET_TIMEOUT, (0x1a4), a reset will occur. Values below 1000 are treated as zero and values above 255000 are truncated to 255000. This feature allows a host to initialise the system to a known state. Also, WT11u can emit a break character that may be used to wake the host. Figure 20: Break Signal Table 13 shows a list of commonly used data rates and their associated values for PSKEY_UART_BAUD_RATE

(0x204). There is no requirement to use these standard values. Any data rate within the supported range can be set in the PS Key according to the formula in Equation 1 Silicon Laboratories Finland Oy Page 26 of 51 Equation 1: Data Rate Data rate [bits/s]

Persistent store value Error [bits/s]

Error [%]

1200 2400 4800 9600 19200 38400 57600 76800 115200 230400 460800 921600 1382400 1843200 2764800

(Hex) 0x0005 0x000A 0x0014 0x0027 0x004F 0x009D 0x00EC 0x013B 0x01D8 0x03B0 0x075F 0x0EBF 0x161E 0x1D7E 0x2C3D 5 10 20 39 79 157 236 315 472 944 1887 3775 5662 7550 11325 1.73 1.73 1.73

-0.82 0.45

-0.18 0.03 0.14 0.03 0.03

-0.02 0

-0.01 0 0 Table 13: Standard Data Rates Silicon Laboratories Finland Oy Page 27 of 51 6.1 UART Bypass Figure 21: UART Bypass Architecture 6.2 UART Configuration While Reset is Active The UART interface for WT11u while the chip is being held in reset is tristate. This will allow the user to daisy chain devices onto the physical UART bus. The constraint on this method is that any devices connected to this bus must tristate when WT11u reset is de-asserted and the firmware begins to run. 6.3 UART Bypass Mode Alternatively, for devices that do not tristate the UART bus, the UART bypass mode on the chipset can be used. The default state of the chipset after reset is de-asserted; this is for the host UART bus to be connected to the chipset UART, thereby allowing communication to the chipset via the UART. All UART bypass mode connections are implemented using CMOS technology and have signalling levels of 0V and VDD. In order to apply the UART bypass mode, a BCCMD command will be issued the chipset. Upon this issue, it will switch the bypass to PIO[7:4] as Figure 21 indicates. Once the bypass mode has been invoked, WT11u will enter the Deep Sleep state indefinitely. In order to re-establish communication with WT11u, the chip must be reset so that the default configuration takes effect. It is important for the host to ensure a clean Bluetooth disconnection of any active links before the bypass mode is invoked. Therefore, it is not possible to have active Bluetooth links while operating the bypass mode. The current consumption for a device in UART bypass mode is equal to the values quoted for a device in standby mode. Silicon Laboratories Finland Oy Page 28 of 51 7 USB Interface This is a full speed (12Mbits/s) USB interface for communicating with other compatible digital devices. WT11u acts as a USB peripheral, responding to requests from a master host controller such as a PC. The USB interface is capable of driving a USB cable directly. No external USB transceiver is required. The device operates as a USB peripheral, responding to requests from a master host controller such as a PC. Both the OHCI and the UHCI standards are supported. The set of USB endpoints implemented can behave as specified in the USB section of the Bluetooth v2.1 + EDR specification or alternatively can appear as a set of endpoints appropriate to USB audio devices such as speakers. As USB is a master/slave oriented system (in common with other USB peripherals), WT11u only supports USB Slave operation. 7.1 USB Data Connections The USB data lines emerge as pins USB_DP and USB_DN. These terminals are connected to the internal USB I/O buffers of the chipset, therefore, have a low output impedance. To match the connection to the characteristic impedance of the USB cable, resistors must be placed in series with USB_DP/USB_DN and the cable. 7.2 USB Pull-Up resistor WT11u features an internal USB pull-up resistor. This pulls the USB_DP pin weakly high when WT11u is ready to enumerate. It signals to the PC that it is a full speed (12Mbits/s) USB device. The USB internal pull-up is implemented as a current source, and is compliant with section 7.1.5 of the USB specification v1.2. The internal pull-up pulls USB_DP high to at least 2.8V when loaded with a 15k 5% pull-

down resistor (in the hub/host) when VDD_PADS = 3.1V. This presents a Thevenin resistance to the host of at least 900. Alternatively, an external 1.5k pull-up resistor can be placed between a PIO line and D+ on the USB cable. The firmware must be alerted to which mode is used by setting PSKEY_USB_PIO_PULLUP appropriately. The default setting uses the internal pull-up resistor. 7.3 USB Power Supply The USB specification dictates that the minimum output high voltage for USB data lines is 2.8V. To safely meet the USB specification, the voltage on the VDD supply terminal must be an absolute minimum of 3.1V. Silicon Labs recommends 3.3V for optimal USB signal quality. 7.4 Self-Powered Mode In self-powered mode, the circuit is powered from its own power supply and not from the VBUS (5V) line of the USB cable. It draws only a small leakage current (below 0.5mA) from VBUS on the USB cable. This is the easier mode for which to design, as the design is not limited by the power that can be drawn from the USB hub or root port. However, it requires that VBUS be connected to WT11u via a resistor network (Rvb1 and Rvb2), so WT11u can detect when VBUS is powered up. The chipset will not pull USB_DP high when VBUS is off. Self-powered USB designs (powered from a battery or PSU) must ensure that a PIO line is allocated for USB pullup purposes. A 1.5k 5% pull-up resistor between USB_DP and the selected PIO line should be fitted to the design. Failure to fit this resistor may result in the design failing to be USB compliant in self-powered mode. The internal pull-up in the chipset is only suitable for bus-powered USB devices, e.g., dongles. Silicon Laboratories Finland Oy Page 29 of 51 Figure 22: USB Connections for Self-Powered Mode The terminal marked USB_ON can be any free PIO pin. The PIO pin selected must be registered by setting PSKEY_USB_PIO_VBUS to the corresponding pin number. Identifier Value Function Rs Rvb1 Rvb2 0-10 as needed by the design **

Impedance matching to USB 22k 5%

47k 5%

cable VBUS ON sense divider VBUS ON sense divider

**) WT11u has internal 22 ohm series resistors at the USB lines. Figure 23: USB Interface Component Values 7.5 Bus-Powered Mode In bus-powered mode, the application circuit draws its current from the 5V VBUS supply on the USB cable. WT11u negotiates with the PC during the USB enumeration stage about how much current it is allowed to consume. On power-up the device must not draw more than 100 mA but after being configured it can draw up to 500 mA. For WT11u, the USB power descriptor should be altered to reflect the amount of power required. This is accomplished by setting PSKEY_USB_MAX_POWER (0x2c6). This is higher than for a Class 2 application due to the extra current drawn by the Transmit RF PA. By default for WT11u the setting is 300 mA. When selecting a regulator, be aware that VBUS may go as low as 4.4V. The inrush current (when charging reservoir and supply decoupling capacitors) is limited by the USB specification. See the USB Specification. Some applications may require soft start circuitry to limit inrush current if more than 10uF is present between VBUS and GND. The 5V VBUS line emerging from a PC is often electrically noisy. As well as regulation down to 3.3V and 1.8V, applications should include careful filtering of the 5V line to attenuate noise that is above the voltage regulator bandwidth. Excessive noise on WT11u supply pins will result in reduced receiver sensitivity and a distorted RF transmit signal. Silicon Laboratories Finland Oy Page 30 of 51 Figure 24: USB Connections for Bus-Powered Mode 7.6 USB Suspend Current All USB devices must permit the USB controller to place them in a USB suspend mode. While in USB Suspend, bus-powered devices must not draw more than 2.5mA from USB VBUS (self-powered devices may draw more than 2.5mA from their own supply). This current draw requirement prevents operation of the radio by bus-

powered devices during USB Suspend. When computing suspend current, the current from VBUS through the bus pull-up and pull-down resistors must be included. The pull-up resistor at the device is 1.5k. (nominal). The pull-down resistor at the hub is 14.25k. to 24.80k. The pull-up voltage is nominally 3.3V, which means that holding one of the signal lines high takes approximately 200uA, leaving only 2.3mA available from a 2.5mA budget. Ensure that external LEDs and/or amplifiers can be turned off by the chipset. The entire circuit must be able to enter the suspend mode. 7.7 USB Detach and Wake-Up Signaling WT11u can provide out-of-band signaling to a host controller by using the control lines called USB_DETACH and USB_WAKE_UP. These are outside the USB specification (no wires exist for them inside the USB cable), but can be useful when embedding WT11u into a circuit where no external USB is visible to the user. Both control to any PIO pin by setting PSKEY_USB_PIO_DETACH and PSKEY_USB_PIO_WAKEUP to the selected PIO number. lines are shared with PIO pins and can be assigned USB_DETACH is an input which, when asserted high, causes WT11u to put USB_DN and USB_DP in high impedance state and turns off the pull-up resistor on DP. This detaches the device from the bus and is logically equivalent to unplugging the device. When USB_DETACH is taken low, WT11u will connect back to USB and await enumeration by the USB host. USB_WAKE_UP is an active high output (used only when USB_DETACH is active) to wake up the host and allow USB communication to recommence. It replaces the function of the software USB WAKE_UP message

(which runs over the USB cable) and cannot be sent while chipset is effectively disconnected from the bus. Silicon Laboratories Finland Oy Page 31 of 51 Figure 25: USB_Detach and USB_Wake_Up Signals 7.8 USB Driver A USB Bluetooth device driver is required to provide a software interface between the chipset and the Bluetooth software running on the host computer. 7.9 USB v2.0 Compliance and Compatibility Although WT11u meets the USB specification, Silicon Labs cannot guarantee that an application circuit designed around the module is USB compliant. The choice of application circuit, component choice and PCB layout all affect USB signal quality and electrical characteristics. The information in this document is intended as a guide and should be read in association with the USB specification, with particular attention being given to Chapter 7. Independent USB qualification must be sought before an application is deemed USB compliant and can bear the USB logo. Such qualification can be obtained from a USB plugfest or from an independent USB test house. Terminals USB_DP and USB_DN adhere to the USB Specification v2.0 (Chapter 7) electrical requirements. The chipset is compatible with USB v2.0 host controllers; under these circumstances the two ends agree the mutually acceptable rate of 12Mbits/s according to the USB v2.0 specification. Silicon Laboratories Finland Oy Page 32 of 51 8 Serial Peripheral Interface (SPI) The SPI port can be used for system debugging. It can also be used for programming the Flash memory and setting the PSKEY configurations. WT11u uses 16-bit data and 16-bit address serial peripheral interface, where transactions may occur when the internal processor is running or is stopped. SPI interface is connected using the MOSI, MISO, CSB and CLK pins. SPI interface cannot be used for application purposes. Silicon Laboratories Finland Oy Page 33 of 51 9 PCM Codec Interface PCM is a standard method used to digitize audio (particularly voice) for transmission over digital communication channels. Through its PCM interface, WT11u has hardware support for continual transmission and reception of PCM data, thus reducing processor overhead for wireless headset applications. WT11u offers a bidirectional digital audio interface that routes directly into the baseband layer of the on-chip firmware. It does not pass through the HCI protocol layer. Hardware on WT11u allows the data to be sent to and received from a SCO connection. Up to three SCO connections can be supported by the PCM interface at any one time. WT11u can operate as the PCM interface master generating an output clock of 128, 256 or 512kHz. When configured as PCM interface slave, it can operate with an input clock up to 2048kHz. WT11u is compatible with a variety of clock formats, including Long Frame Sync, Short Frame Sync and GCI timing environments. It supports 13-bit or 16-bit linear, 8-bit -law or A-law companded sample formats at 8ksamples/s and can receive and transmit on any selection of three of the first four slots following PCM_SYNC. The PCM configuration options are enabled by setting PSKEY_PCM_CONFIG32. WT11u interfaces directly to PCM audio devices. NOTE: Analog audio lines are very sensitive to RF disturbance. Use good layout practices to ensure noise less audio. Make sure that the return path for the audio signals follows the forward current all the way as close as possible and use fully differential signals when possible. Do not compromise audio routing. 9.1 PCM Interface Master/Slave When configured as the master of the PCM interface, WT11u generates PCM_CLK and PCM_SYNC. When configured as the Slave of the PCM interface, WT11u accepts PCM_CLK rates up to 2048kHz. Figure 26: PCM Interface Master Silicon Laboratories Finland Oy Page 34 of 51 Figure 27: PCM Interface Slave 9.2 Long Frame Sync Long Frame Sync is the name given to a clocking format that controls the transfer of PCM data words or samples. In Long Frame Sync, the rising edge of PCM_SYNC indicates the start of the PCM word. When WT11u is configured as PCM master, generating PCM_SYNC and PCM_CLK, then PCM_SYNC is 8-bits long. When WT11u is configured as PCM Slave, PCM_SYNC may be from two consecutive falling edges of PCM_CLK to half the PCM_SYNC rate, i.e., 62.5s long. Figure 28: Long Frame Sync (Shown with 8-bit Companded Sample) WT11u samples PCM_IN on the falling edge of PCM_CLK and transmits PCM_OUT on the rising edge. PCM_OUT may be configured to be high impedance on the falling edge of PCM_CLK in the LSB position or on the rising edge. 9.3 Short Frame Sync In Short Frame Sync, the falling edge of PCM_SYNC indicates the start of the PCM word. PCM_SYNC is always one clock cycle long. Silicon Laboratories Finland Oy Page 35 of 51 Figure 29: Short Frame Sync (Shown with 16-bit Sample) As with Long Frame Sync, WT11u samples PCM_IN on the falling edge of PCM_CLK and transmits PCM_OUT on the rising edge. PCM_OUT may be configured to be high impedance on the falling edge of PCM_CLK in the LSB position or on the rising edge. 9.4 Multi-slot Operation More than one SCO connection over the PCM interface is supported using multiple slots. Up to three SCO connections can be carried over any of the first four slots. Figure 30: Multi-slot Operation with Two Slots and 8-bit Companded Samples 9.5 GCI Interface WT11u is compatible with the GCI, a standard synchronous 2B+D ISDN timing interface. The two 64kbits/s B channels can be accessed when this mode is configured. Silicon Laboratories Finland Oy Page 36 of 51 Figure 31: GCI Interface The start of frame is indicated by the rising edge of PCM_SYNC and runs at 8kHz. With WT11u in Slave mode, the frequency of PCM_CLK can be up to 4.096MHz. 9.6 Slots and Sample Formats WT11u can receive and transmit on any selection of the first four slots following each sync pulse. Slot durations can be either 8 or 16 clock cycles. Durations of 8 clock cycles may only be used with 8-bit sample formats. Durations of 16 clocks may be used with 8-bit, 13-bit or 16-bit sample formats. WT11u supports 13-bit linear, 16-bit linear and 8-bit -law or A-law sample formats. The sample rate is 8ksamples/s. The bit order may be little or big endian. When 16-bit slots are used, the 3 or 8 unused bits in each slot may be filled with sign extension, padded with zeros or a programmable 3-bit audio attenuation compatible with some Motorola codecs. Silicon Laboratories Finland Oy Page 37 of 51 Figure 32: 16-bit Slot Length and Sample Formats 9.7 Additional Features WT11u has a mute facility that forces PCM_OUT to be 0. In master mode, PCM_SYNC may also be forced to 0 while keeping PCM_CLK running which some codecs use to control power down. 9.8 PCM_CLK and PCM_SYNC Generation WT11u has two methods of generating PCM_CLK and PCM_SYNC in master mode. The first is generating these signals by DDS from the chipset internal 4MHz clock. Using this mode limits PCM_CLK to 128, 256 or 512kHz and PCM_SYNC to 8kHz. The second is generating PCM_CLK and PCM_SYNC by DDS from an internal 48MHz clock (which allows a greater range of frequencies to be generated with low jitter but consumes more power). This second method in PSKEY_PCM_CONFIG32. When in this mode and with long frame sync, the length of PCM_SYNC can be either 8 or 16 cycles of PCM_CLK, determined by LONG_LENGTH_SYNC_EN in PSKEY_PCM_CONFIG32. is selected by setting bit 48M_PCM_CLK_GEN_EN The Equation XXX describes PCM_CLK frequency when being generated using the internal 48MHz clock:

Silicon Laboratories Finland Oy Page 38 of 51 Equation 2: PCM_CLK Frequency When Being Generated Using the Internal 48MHz Clock The frequency of PCM_SYNC relative to PCM_CLK can be set using Equation XXX:

Equation 3: PCM_SYNC Frequency Relative to PCM_CLK CNT_RATE, CNT_LIMIT and SYNC_LIMIT are set using PSKEY_PCM_LOW_JITTER_CONFIG. As an example, set PSKEY_PCM_LOW_JITTER_CONFIG to 0x08080177. PCM_SYNC PCM_CLK generate 512kHz 8kHz, with to at at 9.9 PCM Configuration The PCM configuration is set using two PS Keys, PSKEY_PCM_CONFIG32 detailed in Error! Reference ource not found. and PSKEY_PCM_LOW_JITTER_CONFIG in Error! Reference source not found.. The default for PSKEY_PCM_CONFIG32 is 0x00800000, i.e., first slot following sync is active, 13-bit linear voice format, long frame sync and interface master generating 256kHz PCM_CLK from 4MHz internal clock with no tri-state of PCM_OUT. Silicon Laboratories Finland Oy Page 39 of 51 Name

-

SLAVE MODE EN SHORT SYNC EN

-

SIGN EXTENDED EN LSB FIRST EN TX TRISTATE EN TX TRISTATE RISING EDGE EN Bit position 0 1 2 3 4 5 6 7 Description Set to 0 0 selects Master mode with internal generation of PCM_CLK and PCM_SYNC. 1 selects Slave mode requiring externally generated PCM_CLK and PCM_SYNC. This should be set to 1 if 48M_PCM_CLK_GEN_EN (bit 11) is set. 0 selects long frame sync (rising edge indicates start of frame), Set to 0 0 selects long frame sync (rising edge indicates start of frame), 1 selects short frame sync (falling edge indicates start of frame). 0 transmits and receives voice samples MSB first, 1 uses LSB 0 transmits and receives voice samples MSB first, 1 uses LSB 0 tristates PCM_OUT immediately after the falling edge of PCM_CLK in the last bit of an active slot, assuming the next slot is also not active. 1 tristates PCM_OUT after the rising edge of PCM_CLK. SYNC SUPPRESS 8 EN 0 enables PCM_SYNC output when master, 1 suppresses PCM_SYNC whilst keeping PCM_CLK running. Some CODECS utilize this to enter a GCI MODE EN MUTE EN 48M PCM CLK GEN EN 9 10 11 low power state 1 enables GCI mode. 1 forces PCM_OUT to 0. 0 sets PCM_CLK and PCM_SYNC generation via DDS from internal 4 MHz clock. 1 sets PCM_CLK and PCM_SYNC generation via DDS from internal 48 MHz clock. LONG LENGTH 12 0 sets PCM_SYNC length to 8 PCM_CLK cycles and 1 sets length to 16 SYNC EN PCM_CLK cycles. Only applies for long frame sync and with 48M_PCM_CLK_GEN_EN set to 1.

-

[20:16]

Set to 0b00000. MASTER CLK

[22:21]

Selects 128 (0b01), 256 (0b00), 512 (0b10) kHz PCM_CLK frequency RATE when master and 48M_PCM_CLK_GEN_EN (bit 11) is low. ACTIVE SLOT

[26:23]

Default is 0001. Ignored by firmaware SAMPLE FORMAT

[28:27]

Selects between 13 (0b00), 16 (0b01), 8 (0b10) bit sample with 16 cycle slot duration 8 (0b11) bit sample 8 cycle slot duration. Table 14: PSKEY_PCM_CONFIG32 description Silicon Laboratories Finland Oy Page 40 of 51 Name Bit position CNT LIMIT CNT RATE SYNC LIMIT

[12:0]

[23:16]

[31:24]

Description Sets PCM_CLK counter limit Sets PCM_CLK count rate Sets PCM_SYNC division relative to PCM_CLK Table 15: PSKEY_PCM_LOW_JITTER_CONFIG Description Silicon Laboratories Finland Oy Page 41 of 51 10 I/O Parallel Ports Six lines of programmable bidirectional input/outputs (I/O) are provided. All the PIO lines are power from VDD. PIO lines can be configured through software to have either weak or strong pull-ups or pull-downs. All PIO lines are configured as inputs with weak pull-downs at reset. Any of the PIO lines can be configured as interrupt request lines or as wake-up lines from sleep modes. WT11u has a general purpose analogue interface pin AIO[1]. This is used to access internal circuitry and control signals. It may be configured to provide additional functionality. Auxiliary functions available via AIO[1] include an 8-bit ADC and an 8-bit DAC. Typically the ADC is used for battery voltage measurement. Signals selectable at this pin include the band gap reference voltage and a variety of clock signals: 48, 24, 16, 8MHz and the XTAL clock frequency. When used with analogue signals, the voltage range is constrained by the analogue supply voltage internally to the module (1.8V). When configured to drive out digital level signals (e.g., clocks), the output voltage level is determined by VDD. 10.1 PIO Defaults Silicon Labs cannot guarantee that these terminal functions remain the same. Refer to the software release note for the implementation of these PIO lines, as they are firmware build-specific. Silicon Laboratories Finland Oy Page 42 of 51 11 Reset WT11u may be reset from several sources: RESET pin, power on reset, a UART break character or via software configured watchdog timer. The RESET pin is an active high reset and is internally filtered using the internal low frequency clock oscillator. A reset will be performed between 1.5 and 4.0ms following RESETB being active. It is recommended that RESET be applied for a period greater than 5ms. The power on reset occurs when the VDD_CORE supply internally to the module falls below typically 1.5V and is released when VDD_CORE rises above typically 1.6V. At reset the digital I/O pins are set to inputs for bidirectional pins and outputs are tri-state. WT11u has an internal power on reset circuit which holds the module in reset until all the supply voltages have stabilized. The reset pin must be either floating or connected to high impedance during power on in order for the power on reset circuit to work properly. If the reset pin is not connected to high impedance during power on, then one must ensure that the reset is kept active until all the supply voltages have stabilized to prevent the flash memory getting corrupted. Silicon Laboratories Finland Oy Page 43 of 51 11.1 Pin States on Reset Pad name PIO[7:2]

PCM_OUT PCM_IN PCM_SYNC PCM_CLK UART_TX UART_RX UART_RTS UART_CTS USB+

USB-

SPI_CSB SPI_CLK SPI_MOSI SPI_MISO AIO[1]

State Input, weak pull-down 3-state, weak pull-down Input, weak pull-down Input, weak pull-down Input, weak pull-down 3-state, weak pull-up Input, weak pull-down 3-state, weak pull-up Input, weak pull-down Input, weak pull-down Input, weak pull-down Input, weak pull-down Input, weak pull-down Input, weak pull-down 3-state, weak pull-down Output, driving low Table 16: Pin States on Reset Silicon Laboratories Finland Oy Page 44 of 51 12 Certifications The certifications for the WT11u are pending. 12.1 Bluetooth The WT11u module is Bluetooth qualified and listed as a controller subsystem and it is Bluetooth compliant to the following profiles of the core spec version 2.1/2.1+EDR. Baseband HCI Link Manager Radio The WT11u-E radio has been tested using an external antenna with a maximum gain of 2.3 dBi and the Bluetooth qualification is valid for any antenna with the same or less gain. 12.2 FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by Bluegiga Technologies could void the users authority to operate the equipment. FCC RF Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter meets both portable and mobile limits as demonstrated in the RF Exposure Analysis. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. As long as the condition above is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). OEM Responsibilities to comply with FCC Regulations The WT11U Module has been certified for integration into products only by OEM integrators under the following conditions:

The antenna(s) must be installed such that a minimum separation distance of 42 mm is maintained between the radiator (antenna) and all persons at all times. Silicon Laboratories Finland Oy Page 45 of 51 The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The WT11U module is labeled with its own FCC ID. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:

Contains Transmitter Module FCC ID: QOQWT11U or Contains FCC ID: QOQWT11U The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product 12.3 ISEDC This radio transmitter (IC: 5123A-WT11U) has been approved by Industry Canada to operate with the embedded chip antenna and the antennas listed in the table 18. Other antenna types are strictly prohibited for use with this device. This device complies with Industry Canadas license-exempt RSS standards. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device RF Exposure Statement Exception from routine SAR evaluation limits are given in RSS-102 Issue5. WT11U meets the given requirements when the minimum separation distance to human body is less than equal to 40 mm. RF exposure or SAR evaluation is not required when the separation distance is 40 mm or more. If the separation distance is less than 40 mm the OEM integrator is responsible for evaluating the SAR. OEM Responsibilities to comply with IC Regulations The WT11U Module has been certified for integration into products only by OEM integrators under the following conditions:

The antenna(s) must be installed such that a minimum separation distance of 40 mm is maintained between the radiator (antenna) and all persons at all times. Silicon Laboratories Finland Oy Page 46 of 51 The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter. As long as the two conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for certain configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC authorization End Product Labeling The WT11U module is labeled with its own IC ID. If the IC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:

Contains Transmitter Module IC: 5123A-WT11U or Contains IC: 5123A-WT11U The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product 12.3.1 IC (franais) Cet metteur radio (IC : 5123A-WT11U) a reu l'approbation d'Industrie Canada pour une exploitation avec l'antenne puce incorpore. Il est strictement interdit d'utiliser d'autres types d'antenne avec cet appareil. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) lappareil ne doit pas produire de brouillage;

2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Dclaration relative l'exposition aux radiofrquences (RF) Les limites applicables lexemption de lvaluation courante du DAS sont nonces dans le CNR 102, 5 e dition. L'appareil WT11U rpond aux exigences donnes quand la distance de sparation minimum par rapport au corps humain est infrieure ou gale 40 mm. L'valuation de l'exposition aux RF ou du DAS n'est pas requise quand la distance de sparation est de 40 mm ou plus. Si la distance de sparation est infrieure 40 mm, il incombe l'intgrateur FEO d'valuer le DAS. Responsabilits du FEO ayant trait la conformit avec les rglements IC Le module WT11U a t certifi pour une intgration dans des produits uniquement par les intgrateurs FEO dans les conditions suivantes :

La ou les antennes doivent tre installes de telle faon qu'une distance de sparation minimum de 40 mm soit maintenue entre le radiateur (antenne) et toute personne tout moment. Silicon Laboratories Finland Oy Page 47 of 51 Le module metteur ne doit pas tre install au mme endroit ou fonctionner conjointement avec toute autre antenne ou metteur. Ds lors que les deux conditions ci-dessus sont respectes, d'autres tests de l'metteur ne sont pas obligatoires. Cependant, il incombe toujours l'intgrateur FEO de tester la conformit de son produit final vis-

-vis de toute exigence supplmentaire avec ce module install (par exemple, missions de dispositifs numriques, exigences relatives aux matriels priphriques PC, etc). REMARQUE IMPORTANTE : S'il s'avre que ces conditions ne peuvent tre respectes (pour certaines configurations ou la colocation avec un autre metteur), alors l'autorisation IC n'est plus considre comme valide et l'identifiant IC ne peut plus tre employ sur le produit final. Dans ces circonstances, l'intgrateur FEO aura la responsabilit de rvaluer le produit final (y compris l'metteur) et d'obtenir une autorisation IC distincte. tiquetage du produit final L'tiquette du module WT11U porte son propre identifiant IC. Si l'identifiant IC n'est pas visible quand le module est install l'intrieur d'un autre appareil, l'extrieur de l'appareil dans lequel le module est install doit aussi porter une tiquette faisant rfrence au module qu'il contient. Dans ce cas, une tiquette comportant les informations suivantes doit tre colle sur une partie visible du produit final :

Contient le module metteur IC : 5123A-WT11U ou Contient IC : 5123A-WT11U L'intgrateur FEO doit tre conscient de ne pas fournir d'informations l'utilisateur final permettant d'installer ou de retirer ce module RF ou de changer les paramtres lis aux RF dans le mode d'emploi du produit final. 12.4 CE The WT11u is in conformity with the essential requirements and other relevant requirements of the R&TTE Directive (1999/5/EC) and Radio Equiment Directive (RED) . This device is compliant with the following standards:

Safety: EN 60950 EMC: EN 301 489 Spectrum: EN 300 328 RF Exposure: EN 62479 Formal DoC is available from www.silabs.com. 12.5 MIC Japan TBD 12.6 KCC (Korea) TBD Silicon Laboratories Finland Oy Page 48 of 51 12.7 Anatel TBD Silicon Laboratories Finland Oy Page 49 of 51 12.8 Qualified Antenna Types for WT11u-E This device has been designed to operate with a standard 2.14 dBi dipole antenna. Any antenna of a different type or with a gain higher than 2.14 dBi is strictly prohibited for use with this device. Using an antenna of a different type or gain more than 2.14 dBi will require additional testing for FCC, CE and IC. The required antenna impedance is 50 . Antenna type Dipole Maximum gain 2.14 dBi Table 17: Qualified Antenna Types for WT11u-E To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that permitted for successful communication. Any standard 2.14 dBi dipole antenna can be used without an additional application to FCC. 12.9 Moisture Sensitivity Level (MSL) Moisture sensitivity level (MSL) of this product is 3. For the handling instructions please refer to JEDEC J-STD-

020 and JEDEC J-STD-033. If baking is required, devices may be baked for 12 hours at 125C +/-5C for high temperature device containers. Silicon Laboratories Finland Oy Page 50 of 51 Silicon Laboratories Finland Oy Page 51 of 51