submitted | available | document details (if available) | source link |
---|---|---|---|
September 25 2019 | September 25 2019 | Adobe PDF Library 15.0 |
various | User Manual | Users Manual | 547.96 KiB | September 25 2019 |
B Sensor Quick Start Guide Setting up your B Sensors B Sensor Installation 1. Each SmartSense B Sensor is shipped in a package labeled with the name of the piece of equipment it belongs to 2. SmartSense B Sensors are shipped active and ready to communicate 3. Using the included zip ties, secure the B Sensor inside your equipment Trim excess zip tie so the B Sensor looks similar to the photos below 4. Make note of each sensors serial number (for example, D0001234) and the names of the refrigerated units theyre installed in This information will be used to name the sensors in the View Data and Manage Devices section www.smartsense.co A1/819 B Gateway Installation 1. The SmartSense B Gateway is a hub that receives temperature and time data from the B Sensors 2. Data is synced to the host over your Wi-Fi or a cellular connection 3. Additional supplies needed:
12 V power supply Velcro fasteners Zip ties 4. Connecting your B Gateway Login to the mobile application using the Username and Password provided in your welcome packet Download the Digi Coldchain app from the iOS App Store or Google Play Note: The B Gateway can take up to 10 minutes to report a connection when first powered on From the dashboard, tap on the Menu button Tap Gateways www.smartsense.co A1/819 Here you will see if the gateway connected successfully When installing the B Gateway, choose placement that is central to all of your sensors and make sure it has a line of sight path to the sensors The following is a typical kitchen layout that demonstrates how to install your sensors and gateway Use the mounting holes on the B Gateway or the provided Velcro fasteners to install the device View Data and Manage Devices 1. B Sensors check the temperature every 60 seconds and send temperature data to the B Gateway every 10 minutes, or when the temperature changes 1.5C (2.7C) or more 2. The B Gateway reports temperature data to the SmartSense dashboard every 5 minutes 3. You can view the data on the SmartSense dashboard by signing into the mobile app or website 4. Use the dashboard to do the following:
View temperature details, graphs, and warning, or alerts for all your sensor-equipped units Set high and low tempearture ranges for alert notifications Mange B Sensors and B Gateway Acknowledge alerts Filter data to specific B Sensors or B Gateways Print or export temperature data as reports 5. For additional support visit help.smartsense.co www.smartsense.co A1/819 SmartSense B Sensor: Regulatory Information RF Exposure Statement In order to comply with RF exposure limits established in the ANSI C95.1 standards, the distance between the antenna or antennas and the user should not be less than 20 cm. FCC Certifications and Regulatory Information (USA only) FCC Part 15 Class B This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Radio Frequency Interface (RFI) (FCC 15.105) This device has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 Subpart B, of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Modifications (FCC 15.21) CAUTION: Changes or modifications to this equipment not expressly approved by Digi may void the users authority to operate this equipment. Industry Canada (IC) Certifications This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage, et
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. For more information about SmartSense visit www.smartsense.co or call 1-866-806-2653 1996-2019 Digi International Inc. All rights reserved. All other trademarks are the property of their respective owners. A1/819
This product uses the FCC Data API but is not endorsed or certified by the FCC