FCC ID: 2AU8HSRM310 LTE-A Hotspot

A B C D E F G H I J K L 1 2 3 4 5 6 7 8 9 10 11 12 13 14 REV. V1.0

ZONE

DATE 2021-05-17

DESCRIPTION 15 SIGN Zhou Mo

16 APPROVER Tong Mingxu

Introduction Packing List Configure hardware Please also prepare the following tools:Screw DriversAdjustable spannerDebug Ethernet Cable Ethernet Cable Connection:

LTE outdoor CPE is a highly advanced LTE outdoor multi-service product solution specically designed to meet integrated data needs for residential, business and enterprise users. The product supports advanced Gigabit networking functionalities. It enables wide service coverage and provides high data throughput and networking features to customers who needs easy broadband access. Make sure you have everything you need to properly congure the device. Please make sure that you are familiar with all accident prevention and safety procedures necessary for working at height and with electrici-

ty before starting to install the device. DO NOT install the ODU during a lightning storm. CAUTION Insert a SIM Card to the Slot Make sure the ODU is turned off before you insert your SIM card. It is recommended to NOT connect the PoE cable when you do this step. Otherwise, the SIM card may be damaged. CAUTION Choose Install Location When choosing a location to install the ODU, remember that the ODUs front panel should point towards your service providers nearest base station. You do not need to be able to see the base station from the ODUs position. However, if you have trouble with signal reception, a Line of Sight (LoS) connection may produce better results. The ODU must be within the lightning rod protection scope (45 degrees) to avoid being damaged by a lightning strike. If the ODU is installed on a rooftop, the ODU must be less than 2 m above the rooftop. NOTE: Make sure you have inserted your SIM card into the ODU. Step 1 Connect the CAT5e or higher level Ethernet cable which is connected to the ODU to the PoE port. Step 2 Connect the included Ethernet cable from the computer to Data port of the POE. ODU PoE Adapter LTE Outdoor CPE Quick Start Guide ODU PoE Power supply Ethernet cable Stainless steel clamp Cable glands Slotted end cap How does it work 1. Connect the Power Adapter to PoE injector. 2. PoE injector provides the power to ODU via LAN cable. 3. PC connects LAN Cable to PoE, then PC can surf the Internet when ODU accesses the LTE network. Mount the ODU Preparation work This quick installation guide shows you how to congure your ODU in order to access the Internet. Before installing the CPE, verify that you have all the items listed in the packing list,ODU unitPower Adapter & PoE Steel clamp Ethernet CableCable glandsSlotted end capQuick Start Guide if any of the items is missing or damaged, please contact your LTE device provider. Panel of device I/O panel of ODU 1 The ODU performance varies according to the installation position and nearby obstacles, especially metal objects. You are advised to install the ODU in an open area without obstacles. Connect the PoE Installing Outdoor Unit Pole Mounting:

Place a CAT5e (or above) Ethernet cable (not included) from the location of your intended Router to the desired PC location. If you intend to use cable clamps or other methods to secure the cable, do not tighten them until you nish installing the Router and ODU. Hardware connections of Router Computer Step 1 Connect the CAT5e (or above) Ethernet cable to PoE. Do not connect to a computer or switch directly to the PoE port due to high PoE power. CAUTION Step 2 Connect the power adapter to the PoE injector. The POWER LED turns on a solid green-yellow once connected. Step 3 Connect the included Ethernet cable from the computer to one of the Router's Ethernet ports. LED Behavior When setting up the Outdoor Unit, the LED will have the following behavior. 2 3 4 5 6 Steady on Internet available Steady on POWER Off Off INTERNET Blinking

(500ms interval) Steady on SIM Off Green Yellow SIGNAL Red ODU Power on No power supply Internet unavailable Searching network SIM ready No SIM detected Signal strong Signal good Signal weak Blinking Green and Red Firmware upgrade XXXXXX Configure the CPE Login to the website Use a browser to access the management web page to congure and manage the CPE. The following procedure describes how to use a computer running Windows 7 or above version and Internet Explorer to connect to the CPE webpage. Connect to the CPE correctly. Start Step 1 Step 2 address bar, and press Enter. Internet Explorer, type http://192.168.0.1 in the Enter the user name and password, and click Log In. Step 3 You can connect to the management web page after the password is veried. Configuration of LTE Step 1 Connect to the CPE correctly. Step 2 Go to the management website. Step 3 Choose Settings Network LTE Settings. Step 4 Set the connection mode and scan mode. Frequently Asked Questions The parameters are restored to default values. FCC Regulations:

If the CPE powers off unexpectedly while being congured, the parameters may be restored to the default settings. After conguring the parameters, download the conguration le to quickly restore the CPE to the desired settings. The default setting is automatic connection and full band scanning, if you want to connect to the LTE network according to your needs, you can set the connection mode as manual, and simply scan a specic band. Some features of the product and its accessories described herein rely on the software installed, capacities and settings of local network, and may not be activated or may be limited by local network operators or network service providers, thus the descrip-

tions herein may not exactly match the product or its accessories you purchase. We reserves the right to change or modify any information or specications contained in this manual without prior notice or obligation. The CPE fails to search for the LTE network. Notice The POWER indicator does not turn on. Make sure that the power cable is connected to the PoE, and the CPE is connected to the right port of the PoE. Make sure that the power adapter and PoE are compatible with the CPE. Fails to Log in to the web management page. Make sure that the CPE is powered on. Verify that the CPE is correctly connected to the computer through a network cable. If the problem persists, contact authorized local service suppliers. Check that the power adapter and PoE have connected to the CPE properly. Check that the CPE is placed in an open area that is far away from obstructions, such as concrete or wooden walls. Check that the CPE is placed far away from household electrical appliances that generate strong electromagnetic eld, such as microwave ovens, refrigerators, and satellite dishes. If the problem persists, contact authorized local service suppliers. The CPE power adapter has overheated The CPE is heated after being used for long time. Therefore, you must turn off the CPE when not you are using. Check that the CPE is properly ventilated and protected from direct sunlight. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. Changes or modications not expressly approved by the manufacturer could void the users authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To comply with FCC RF Exposure compliance requirements, this grant is applicable to only Mobile Congurations. The antennas used for the transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 12 7 8 9 10 11 Note 1.595x130mm85x130mm 2.128g 3. 4. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 GENERAL TORANCE GRADE A DIM 0~8 0.03 8~25 0.05 25~80 0.08 80~250 0.12 250~ 0.20 B 0.05 0.08 0.12 0.20 0.30 C 0.10 0.20 0.30 0.40 0.50 D 0.20 0.30 0.40 0.50 0.60 SELECT A QUANTITY SCALE SIZE UNIT SHEET VIEW DIRECTION 1 1:1 A1 mm 1 of 1 PART NAME PART NO. PROJECT NAME DESIGN CHECK APPROVAL LTE outdoor CPE

Zhou Mo Wang Huaibing Tong Mingxu MATERIAL FINISH DATE 15 SEE NOTES SEE NOTES 2021-05-17 16 A B C D E F G H I J K L

Comnwwe B2/4/42 Model: SRM310 user name: admin password: admin S/N: 1234567890123456 HT . i re -

ECC ID: 2AU8HSRM310 POWER RATING: 24V ==1.0A MADE IN CHINA Size: 80x37mm QTY: 1pcs

Smawave Technology Co. ,Ltd Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD21046 Subject; Request for Long Term Confidentiality FCC ID: 2AU8HSRM310 To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure Software Security Description UNII declaration letter It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Date: 2021-10-26 Signature:

Name(in print):leven .liang Company: Smawave Technology Co. ,Ltd Adreess: 3F Building 8 1001 North Qinzhou RoadXuhui District Shanghai China

Smawave Technology Co. ,Ltd POWER OF ATTORNEY DATE:November 4, 2021 To:

Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 We, the undersigned, hereby authorize TA Technology (Shanghai) Co., Ltd./zhao junllin on our behalf, to apply to FCC on our equipment for FCC ID: 2AU8HSRM310. Any and all acts carried out by TA Technology (Shanghai) Co., Ltd. on our behalf shall have the same effect as acts of our own for this certificate. Sincerely, Date: 2021-10-26 Signature:

Name(in print): Leven Liang Company: Smawave Technology Co. ,Ltd Adreess: 3F Building 8 1001 North Qinzhou RoadXuhui District Shanghai China