www.somfysystems.com OUTDOOR SUNIS RTS WIREFREE Sun Sensor 9020412 EN Installer Manual www.somfysystems.com SOMFY SYSTEMS INC SOMFY NA HEADQUARTERS 121 Herrod Blvd. Dayton, NJ 08810 P:
NJ: (609) 395-1300 F:
(609) 395-1776
(800) 22-SOMFY (76639) CALIFORNIA 15291 Barranca Parkway Irvine, CA 92618-2201 P:
F: (949) 727-3775
(800) 22-SOMFY (76639) FLORIDA 6100 Broken Sound Pkwy. N.W. Suite 14 Boca Raton, FL 33487 P:
F:
(800) 22-SOMFY (76639)
(561) 995-7502 SOMFY ULC SOMFY Canada Division 5178 Everest Drive Mississauga, Ontario L4W2R4 P:
(800) 66-SOMFY (76639) CN: (905) 564-6446 F:
(905) 238-1491 IC statements:
- This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired Operation of the device.
- Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Copyright 3/2017 Somfy Systems Inc./SAS. All rights reserved. Overview Introduction:
The SUNIS RTS sun sensor provides control of your RTS motorized products based on current sun light levels. It can provide maintenance free service for 5+
years from 2 AA batteries. The precise sun level can easily be selected with 8 possible levels of light sensitivity. The sun function can be enabled/dis-
abled via a Somfy Soliris RTS transmitter or MyLink. A Somfy Soliris RTS transmitter or MyLink must be provided with each installation to enable/disable the sun function. Wirefree, no electrician required Easily select from 8 levels for sun threshold setting Long battery life DEMO mode for fast and easy testing LED feed back for all functions Compatible with full range of RTS exterior motors Ideal for new and existing installations FCC:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:
- This device may not cause harmful interference and
- This device must accept any interference received, including interference that may cause undesired operation Warning! Changes or modications not expressly approved by the manufacturer could void the users authority to operate the equipment. Safety:
Before installing and using this product, please read these instructions carefu lly. Moreover, the installer must comply with current standards and legislation in the country in which the product is being installed, and inform his customers of the operating and maintenance conditions for this product. Any use outside the eld of application specied by Somfy invalidates the warranty and discharges Somfy of all liability, as does any failure to comply with the instructions given herein. Before installing please check the compatibility of this product with the associated equipment and accessories. Specic safety advice:
. Never drop, knock, drill or submerge the SUNIS. Do not use abrasive products or solvents to clean the SUNIS RTS
. Do not clean it using a water spray or high pressure cleaning methods. Ensure that the receiver is kept clean and regularly check if it is operating correctly. SUNIS RTS Specications:
Power In: AA Alkaline Battery Maximum Range: 65 ft. under optimal conditions Operating Temperature: -4 F to 104 F (-20 C to +40 C) IP34 rated for direct weather exposure (Must be mounted correctly as per mounting instructions) o o o o What is in the box:
1. Sunis RTS sensor with built in mounting base 2. 2 AA alkaline batteries 3. 2 mounting screws GETTING STARTED Green Prog LED Red Batt LED Prog Button
-
Sun Level
+
Sun Level Opening the Sunis RTS:
Green LED Level 5-8 Red LED Level 1-4 Fig 1 Fig 2 Rotate the top clockwise to align the arrows on the base and sensor top Fig1. This will allow you to open the sensor by lifting the sensor top from the mounting base Fig 2. Batteries:
Fig 2 Battery Red LED Two AA Alkaline Install the batteries paying attention to the polarity shown on the base Fig 2. If the batteries are good and installed correctly, the RED battery LED will blink just after the batteries are installed. Hint: You can also check if batteries are still good by removing them and reinstalling and conrming the battery LED blinks. Installation:
Fig 3. 1 2 For exterior use, the Sunis RTS must be mounted to a vertical wall. Drill 2 holes 17mm apart Fig 3.1. Mount the Sunis RTS base with the up arrow facing up and the drain hole facing directly down Fig 3.2. Fig4 The mounting location is critical Fig 4. Mount the Sunis RTS facing the direction the awning/screen protects from sun. Ensure it is clear from obstruction that could shade it through out the day. Programming:
Programming Button Fig 5 Fig 6 Adding the Sunis RTS to the motor(s):
Step 1: Press the programming button on the RTS transmitter for 3+ sec until the motor jogs. Fig 5 Step 2: Press the Prog button on the Sunis RTS. Fig 6 The green Prog LED will light and the motor will jog. The Sunis RTS has been added to the motor. Deleting the sensor - Repeat steps 1 and 2 above. Hints:
A Soliris transmitter or MyLink must be programmed to the motor(s) to allow the user to Enable/Disable the sun Function. If a sensor is removed or damaged, it must be cleared from the motor memory. To delete all sensors when adding a new sensor, follow steps 1 and 2 above except on step 2 hold the prog button until the motor jogs twice (approx 7 sec). This Will clear all sensors. Repeat steps 1 and 2 normally to add the new sensor. Setting Sun Threshold Level:
5 2 3 4 Increase Threshold 6 7 8 Thresholds 1 Sunlight intensity
(kLux) 1 5 10 20 40 55 75 100 LED active Red Green Number of ashes Decrease Threshold The Sun Threshold level can be adjusted up or down by a short press of the + or - button. For levels 1-4 the orange LED will blink 1 - 4 times to conrm the level. For levels 5-8 the green LED will blink. DEMO Mode:
Time Delays No Sun Sun Normal Mode 15-30 min 2 min Demo Mode 15 sec 10 sec Demo mode allows the Sunis RTS to be more easily tested by reducing the delay times. Pressing the + & -
together will cause the Sunis to cycle in or out of Demo. The Red and Green LEDs will alternate when entering Demo mode and blink together when exiting. The Sunis Will automatically time out of Demo mode in 3 min.