all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User Manual | Users Manual | 1.76 MiB | ||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | ID Label/Location Info |
1 | User Manual | Users Manual | 1.76 MiB |
www.somfy.com Eolis 3D Wirefree RTS For Awnings FR Notice Installateur DE Installationsanleitung EN Installer Manual D 3 8 5 0 5 0 5 D 3 8 5 0 5 0 5
. f e R FR Notice Installateur Cette notice dcrit linstallation, la mise en service et le mode dutilisation de ce produit. 1. Introduction LEolis 3D WireFree RTS est un capteur de mouvement en trois dimensions sans fil et autonome. Il permet la remonte automatique du store lorsque celui-ci est soumis des secousses provoques par le vent. La dtection des secousses correspond un seuil de sensibilit. Si le store est aussi associ un capteur soleil, les jours venteux et ensoleills, lEolis 3D WireFree RTS dtecte les mouvements intempestifs et bloque louverture du store pour le protger. LEolis 3D WireFree RTS est conu uniquement pour les stores terrasse bras de type banne, coffre ou cassette. LEolis 3D Wirefree RTS est compatible avec la gamme actuelle de moteurs RTS, tlcommandes RTS et capteurs RTS Somfy. 2. Scurit 2.1. Scurit et responsabilit Avant dinstaller et dutiliser ce produit, lire attentivement cette notice. Ce produit doit tre install par un professionnel de la motorisation et de lautomatisation de lhabitat auquel cette notice est destine. Linstallateur doit par ailleurs, se conformer aux normes et la lgislation en vigueur dans le pays dinstallation, et informer ses clients des conditions dutilisation et de maintenance du produit.Toute utilisation hors du domaine dapplication dfini par Somfy est interdite. Elle entranerait, comme tout irrespect des instructions figurant dans cette notice, lexclusion de la responsabilit et de la garantie Somfy. Avant la compatibilit de ce produit avec les quipements et accessoires associs. 2.2. Consignes spcifiques de scurit Ne jamais laisser tomber, choquer, percer, immerger le capteur. installation, vrifier toute A E a c g g d e F Ne pas utiliser de produits abrasifs ni de solvants pour nettoyer le capteur. Ne pas le nettoyer au jet deau, ni sous haute pression. le capteur est Sassurer que toujours propre et vrifier son bon fonctionnement rgulirement. Ce capteur ne protge pas votre store en cas de forte rafale de vent. En cas de risques mtorologiques de ce type, sassurer que le store reste ferm. 3. Contenu (Figure A) Q. 1 1 1 2 Dsignation Eolis 3D WireFree RTS Adhsif double face f. Capteur h. Potentiomtre j. Voyant vert a g Support c d Piles 1,5 V, type AAA (LR03) 4. Eolis 3D RTS en dtails
(Figure B) e. Couvercle g. Support i. Voyant rouge k. Logement des piles l. Bouton de programmation (PROG.) 5. Installation 5.1. Prconisations (Figure C) LEolis 3D WireFree RTS se fixe sur la barre de charge au niveau des extrmits ou au milieu. La dtection des secousses est plus sensible au niveau des extrmits. LEolis 3D WireFree RTS ne doit jamais tre enferm dans la barre de charge !
Le capteur ne doit pas tre plus de 20 m du moteur. Certains quipements forte puis-
sance
(par exemple des casques hifi sans fils) avec une frquence de transmission identique peuvent affecter sa fonction. radio ladhsif 5.2. Fixation avec
(Figure D) Ladhsif fourni est usage unique ! Toujours utiliser ladhsif fourni par Somfy. Lutilisation de tout autre adhsif est interdit !
- Choisir un emplacement sur la face B e f l h i j g k interne ou externe de la barre de charge. La surface doit tre plane et adapte au collage du support.
- Si le positionnement est sur la face interne de la barre de charge:
- contrler que lEolis 3D mont sur son support (g) nempche pas la fermeture du store et ne se dtriore pas.
- Nettoyer la barre de charge.
- Coller ladhsif (c) sur larrire du support (g).
- Fixer lensemble adhsif-support sur la barre de charge :
la flche grave sur le support avec UP doit tre oriente pointe vers le haut. 5.3. Autres moyens de fixation du support (Figure E) Le support (g) se fixe sans rondelle laide de:
- 2 vis cylindriques bombes 4 mm,
- ou 2 vis tte fraise 4 mm,
- ou 2 rivets Pop 4 mm,
- ou 2 accessoires de fixation Somfy
(moyen de fixation non fourni).
- Choisir un emplacement sur la face interne ou externe de la barre de charge.
- Si le positionnement est sur la face interne de la barre de charge:
- contrler que lEolis 3D mont sur son support (g) nempche pas la fermeture du store et ne se dtriore pas.
- En fonction du moyen de fixation choisi, percer deux trous dans la barre de charge selon lentraxe du support (voir Donnes techniques ). sur le support avec UP doit tre oriente pointe vers le haut. Fixer le support : la flche grave 5.4. Mise en place des piles
(Figure F)
- Sortir le capteur (f) du couvercle (e) laide dun tournevis plat.
- Insrer les piles fournies (d) dans le capteur en respectant la polarit indique :
- Le voyant vert (j) sallume pendant 1s si le niveau des piles est suffisant.
- Le voyant rouge (i) clignote si le niveau des piles est insuffisant.
- Laisser le capteur ouvert pour continuer la mise en service. 6. Mise en service (Figure B) Aprs la mise en service, sassurer que le seuil rgl permet la remonte du store. LEolis 3D WireFree RTS ne fonctionne que lorsque lensemble
(e) + (f) est fix au support (g) et que les rglages sont finis. En configuration dorigine la sensi-
bilit est rgl sur une valeur de seuil de 2. Cette sensibilit est suffi-
sante pour assurer la scurit de la plupart des applications. 6.1. Enregistrement de lEolis 3D un moteur (Figure G) Le moteur doit tre dj rgl et enregistr un point de commande. Ne pas enregistrer un Eolis 3D plusieurs moteurs.
- Prendre une tlcommande enregis-
tre dans le moteur.
- Appuyer sur le bouton PROG. de la tlcommande, jusqu ce que le store effectue un va-et-vient.
- Faire un appui bref sur le bouton PROG. (l) du capteur : le moteur effectue un va-et-vient, lEolis 3D est enregistr dans le moteur. 6.2. Seuil pr-dfini Ce rglage correspond une dtection des secousses du store partir de valeurs pr-rgles. Cette sensibilit est suffisante pour assurer la scurit de la plupart des applications. Rglage du Seuil pr-dfini
(Figure H)
- Mettre le potentiomtre (h) sur le seuil voulu laide dun tournevis plat :
- Seuil 1 : des secousses de faible intensit provoquent la remonte du store.
- Vers le seuil 9 : des secousses de plus forte intensit provoquent la remonte du store.
- Insrer le capteur (f) dans le couvercle (e).
- Glisser le
:
support capteur jusquen sur bute le
(g) kabelloser, autonomer DE Installationsanleitung Diese Anleitung beschreibt die Installation, die Inbetriebnahme und die Bedienung dieses Produkts. 1. Einleitung ist Der Eolis 3D WireFree RTS ein und dreidimensionaler Bewegungssensor. Er sorgt das automatische Einfahren einer Markise, wenn heftiger Wind an ihr rttelt. Die Erkennung des Rttelns ist abhngig von einem Grenzwert fr die Empfindlichkeit. Wenn die Markise zustzlich mit einem Sonnensensor kombiniert ist, erkennt der Eolis 3D WireFree RTS heftige Bewegungen und verhindert das Ausfahren der Markise, um diese zu schtzen. Der Eolis 3D WireFree RTS wurde ausschlielich fr den Einsatz in Verbindung mit Gelenkarm-Terrassenmarkisen mit Kasten oder Kassette entwickelt. Der Eolis 3D WireFree RTS ist mit allen aktuellen RTS-Antrieben, RTS-Funksendern und den RTS-Sensoren von Somfy kompatibel. 2. Sicherheitshinweise 2.1. Sicherheit und Gewhrleistung Lesen Sie bitte vor der Montage und Verwendung dieses Produktes diese Installationsanleitung sorgfltig durch. Dieses Produkt darf nur von qualifizierten Gebudetechnikern installiert werden, an welche sich diese Anleitung daher wendet. Der Installateur muss sich auerdem an die Normen und Vorschriften des Installationslandes halten und die Kunden darber informieren, was bei der Benutzung und Wartung des Produkts zu beachten ist. Jede Verwendung zu anderen als den von Somfy vorgegebenen Zwecken gilt als nicht bestimmungsgem. Sie fhrt, wie jede Nichtbeachtung der Anweisungen in dieser Anleitung, zum Ausschluss der Haftung und der Garantie durch Somfy. Vor der Montage muss die Kompatibilitt dieses Produkts mit den dazugehrigen Ausrstungs- und Zubehrteilen geprft werden. 2.2. Spezifische Sicherheitshinweise Lassen Sie den Sensor niemals ihn vor fallen, bewahren Sie Erschtterungen, bohren Sie ihn Wasserstrahl keine Schleif-
nicht an und tauchen Sie ihn nicht in Flssigkeiten. Verwenden Sie zur Reinigung des oder Sensors Lsungsmittel. Reinigen Sie das Gert nicht mit oder einem Hochdruckreiniger. Stellen Sie sicher, dass der Sensor stets sauber ist, und prfen Sie regelmig, ob er einwandfrei funktioniert. Ihre Markise kann durch diesen Sensor pltzlichen Windben geschtzt werden. Stellen Sie im Falle einer meteorologischen Gefahr sicher, dass die Markise eingefahren bleibt. nicht vor 3. Lieferumfang (Abbildung A) S. 1 1 1 2 Bezeichnung Eolis 3D WireFree RTS f. Sensor h. Potentiometer a g Halterung c Doppelseitiger Klebestreifen d Batterien 1,5 V, Typ AAA (LR03) 4. Details des Eolis 3D RTS
(Abbildung B) e. Deckel g. Halterung i. Rote Kontrollleuchte j. Grne Kontrollleuchte k. Batteriefach l. Programmiertaste (PROG.) 5. Montage 5.1. Vorgaben (Abbildung C) Der Eolis 3D WireFree RTS wird an einem der Enden oder in der Mitte des Ausfallprofils installiert. Das Rtteln wird an den Enden besser erkannt. Der Eolis 3D WireFree RTS darf keinesfalls im Ausfallprofil eingeschlos-
sen werden!
Die Entfernung zwischen Sensor und Antrieb nicht darf berschreiten. Gerte mit hoher Funkleistung (zum Beispiel drahtlose Kopfhrer), die dieselbe Frequenz nutzen, knnen seine Funktion stren. 5.2. mit Klebeband (Abbildung D) Das mitgelieferte Klebeband ist nur fr eine einmalige Verwendung bestimmt!
Immer das von Somfy mitgeliefert Klebeband verwenden. Die Verwendung Befestigung 20 m anderer Klebemittel ist nicht zulssig!
- Whlen Sie einen Montageort an der Auen- oder Innenseite des Ausfallprofils. Die Flche muss eben und fr das Ankleben der Halterung geeignet sein.
- Bei einer Befestigung auf der Innenseite des Ausfallprofils:
- Vergewissern Sie sich, dass der auf der Halterung (g) montierte Eolis 3D das Schlieen der Markise nicht behindert und er dabei auch nicht beschdigt wird.
- Reinigen Sie das Ausfallprofil.
- Kleben Sie das Klebeband (c) auf die Rckseite der Halterung (g).
- Befestigen Sie die Halterung mit dem Klebeband am Ausfallprofil:
Der in der Halterung eingravierte Pfeil mit dem Hinweis UP muss mit der Spitze nach oben weisen. 5.3. Andere Befestigungsmittel fr die Halterung (Abbildung E) Die Halterung (g) kann ohne Unterlegscheiben mit folgenden Verbindungsmitteln befestigt werden:
- 2 Flachkopf-Zylinderschrauben 4 mm,
- oder 2 Inbusschrauben 4 mm,
- oder 2 Pop-Nieten 4 mm,
- oder 2 Somfy-Befestigungsmittel (nicht im Lieferumfang).
- Whlen Sie einen Anbringungsort an der Auen- oder Innenseite des Ausfallprofils.
- Bei einer Befestigung auf der Innenseite des Ausfallprofils:
im
- Vergewissern Sie sich, dass der auf der Halterung (g) montierte Eolis 3D das Schlieen der Markise nicht behindert und er dabei auch nicht beschdigt wird.
- Bohren Sie entsprechend dem gewhlten Befestigungsmittel angegebenen Abstand (siehe Technische Daten) zwei Lcher in das Ausfallprofil. der Halterung eingravierte Pfeil mit dem Hinweis UP muss mit der Spitze nach oben weisen. Befestigen Sie die Halterung: Der in 5.4. Einsetzen der Batterien
(Abbildung F)
- Lsen Sie den Sensor
(f) mit einem Schlitzschraubendreher aus dem Gehuse (e).
- Setzen Sie die mitgelieferten Batterien(d) in den Sensor ein und beachten Sie dabei die angegebene Polaritt:
- Die grne Kontrollleuchte (j) leuchtet 1 s lang auf, wenn die Batterien ausreichend geladen sind.
- Wenn die Batterieladung nicht ausreicht, blinkt die rote Kontrollleuchte (i).
- Lassen Sie den Sensor fr die Fortsetzung der Inbetriebnahme geffnet. 6. Inbetriebnahme (Abbildung B) Vergewissern Sie sich nach der Inbetriebnahme, dass der eingestellte Grenzwert fr das Einfahren der Markise sorgt. Der Eolis 3D WireFree RTS funktioniert erst, wenn die Stze von
(e) + (f) an der Halterung (g) befestigt und die Einstellungen abgeschlossen sind. In der Werkseinstellung ist die Empfindlichkeit auf den Wert 2 einge-
stellt. Diese Empfindlichkeit gewhr-
leistet bei den meisten Anwendungen einen sicheren Betrieb. 6.1. Einlernen des Eolis 3D WireFree RTS an einem Antrieb
(Abbildung G) Der Antrieb muss bereits eingestellt und mit einem Funksender verknpft sein. Ein Eolis 3D darf nicht an mehreren Antrieben eingelernt werden. Nehmen Sie einen im Antrieb eingelernten Funksender.
- Drcken Sie die PROG-Taste des Funksenders, bis die Markise mit einer kurzen Vor-/Zurck-Bewegung besttigt.
- Drcken Sie kurz auf die PROG-Taste
(l) des Sensors: Der Antrieb fhrt eine kurze Vor-/Zurck-Bewegung aus, der Eolis 3D ist im Antrieb eingelernt. 6.2. Voreingestellter Grenzwert In dieser Einstellung wird das Rtteln an der Markise anhand voreingestellter Werte erkannt. Diese Empfindlichkeit gewhrleistet bei den meisten Anwendungen einen sicheren Betrieb. nderung des Grenzwerts (Abbildung H)
- Drehen Sie das Potentiometer (h) mit voreingestellten C D L 2 0 m G j i PROG. 2 s f d f e c g PROG. 0.5 s l Donnes techniques Bandes de frquence et Puissance maximale utilise:
433,050 MHz - 434,790 MHz e.r.p. <10 mW Indice de protection : IP 44 Temprature dutilisation :
-20C +60C Alimentation :
2 piles type AAA (LR03), 1,5 V. Technische Daten Frequenzband und maximale leistung:
433.050 MHz - 434.790 MHz e.r.p. <10 mW Schutzart: IP 44 Temperaturbereich:
-20 C bis +60 C Spannungsversorgung:
2 Batterien Typ AAA (LR03), 1,5 V. Technical data Frequency range and max power used:
433.050 MHz - 434.790 MHz e.r.p. <10 mW Index protection rating: IP 44 Operating temperature:
-20C to +60C Power supply:
2 x AAA (LR03) 1.5 V batteries. 38 m m 93.5 mm 120.5 mm 25 mm m 3 m 5 1 Somfy SAS 50 avenue du Nouveau Monde F-74300 CLUSES www.somfy.com FR - Par la prsente Somfy dclare que le produit est conforme aux exigences de la Directive 2014/53/UE. Le texte complet de dclaration de conformit est mis disposition ladresse internet www.somfy.com/ce. DE - SOMFY erklrt hiermit, dass sich dieses Produkt die Anforderungen der Richtlinie 2014/53/EU erfllt. Der vollstndige Text der Konformittserklrung ist unter der Internetadresse www.somfy.com/ce verfgbar. EN - Somfy hereby declares that this product is in compliance with the requirements of Directive 2014/53/EU. The full text of the Declaration of Conformity is available at www. somfy.com/ce. Copyright 2015 Somfy SAS. All rights reserved. Somfy SAS, capital 20.000.000 Euros, RCS Annecy 303.970.230 - 10/2015 5050583D Eolis-3D-RTS-FR-DE-EN.indd 1 Installer Instructions These instructions describes how to install, EN set up and operate this product. 1. Introduction The Eolis 3D WireFree RTS is a wireless and autonomous three-dimensional motion sensor. It automatically retracts the awning when vibration is detected due to wind. The motion detection is configured according to a predetermined sensitivity threshold. If the awning is also connected to a sun sensor, on windy and sunny days, the Eolis 3D WireFree RTS will detect motion and prevent the awning from extending to protect it. The Eolis 3D WireFree RTS is designed only for roller, encased or cassette type folding arm patio awnings. The Eolis 3D WireFree RTS is compatible with the current range of RTS motors, RTS remote controls and RTS Somfy sensors. 2. Safety 2.1. Safety and responsibility Before installing and using this product, please read these instructions carefully. This product must be installed by a professional motorisation and home automation installer, for whom these instructions are intended. Moreover, the installer must comply with current standards and legislation in the country in which the product is being installed, and inform his customers of the operating and maintenance conditions for the product. Any use outside the field of application specified by Somfy is forbidden. This invalidates the warranty and discharges Somfy of all liability, as does any failure to comply with the instructions given herein. Never begin installing without first checking the compatibility of this product with the associated equipment and accessories. 2.2. Specific safety advice Never drop, knock, drill or submerge the sensor. Do not use abrasive products or solvents to clean the sensor. Do not clean it using a water spray or high pressure cleaning methods. Ensure that the sensor is kept clean and regularly check it is operating correctly. This sensor will not protect your awning from heavy gusts of wind. If weather conditions present this sort of risk, ensure that the awning remains closed. 3. Contents (Figure A) Q. 1 1 1 2 Description Eolis 3D WireFree RTS f. Sensor h. Potentiometer j. Green indicator light a g Bracket c Double-sided adhesive d AAA (LR03) 1.5 V batteries 4. Eolis 3D RTS in detail (Figure B) e. Casing g. Bracket i. Red indicator light k. Battery housing l. Programming button (PROG.) 5. Installation 5.1. Recommendations (Figure C) The Eolis 3D WireFree RTS is fixed to the front bar at either end or in the middle. Vibration detection is more effective at either end. The Eolis 3D WireFree RTS must never be The sensor must not be more than Operation can be affected by devices with enclosed in the front bar!
20 m from the motor. high power radio functions (such as wire-
less headphones) that operate on the same transmission frequency. 5.2. Fixing with adhesive (Figure D) The adhesive supplied is only to be used for this operation. Always use the adhe-
sive provided by Somfy. The use of any other adhesive is prohibited.
- Choose a location on the inner or outer face of the front bar. The surface must be flat and suitable for the bracket to be attaches.
- If the position is on the inner face of the front bar:
- check that the Eolis 3D, when mounted on its bracket (g), does not obstruct the closure of the awning and is not damaged during this operation.
- Clean the front bar.
- Apply the adhesive (c) to the rear of the bracket (g).
- Fix the adhesive-bracket assembly to the front bar:
the arrow engraved on the bracket with UP must be positioned to point upwards. 5.3. Other methods for fixing the bracket (Figure E) The bracket (g) is mounted without washers using:
- 2 x 4 mm pan head screws,
- or 2 x 4 mm countersunk screws,
- or 2 x 4 mm pop rivets,
- or 2 Somfy mounting accessories (fixings not supplied).
- Choose a location on the inner or outer face
- If the position is on the inner face of the front of the front bar. bar:
- check that the Eolis 3D, when mounted on its bracket (g), does not obstruct the closure of the awning and is not damaged during this operation.
- Depending on the fixing method chosen, drill two holes in the front bar according to the centre distance of the bracket (see Technical data). the bracket with UP must be positioned to point upwards. Mount the bracket: the arrow engraved on 5.4. Fitting the batteries (Figure F)
- Remove the sensor (f) from the cover (e) using a flat blade screwdriver.
- Insert the batteries supplied (d) in the sensor, taking care to observe the polarity indicated:
The green indicator light (j) will come on for 1 second if the battery level is sufficient.
- The red indicator light (i) will flash if the battery level is insufficient.
- Leave the sensor open to continue the set up. 6. Set up (Figure B) After set up, make sure that the threshold set enables the awning to be raised. The Eolis 3D WireFree RTS will only function when the assembly (e) + (f) is fixed to the bracket (g) and all settings are complete. In the default configuration, the sensitivity threshold value is set to 2. This sensitivity is sufficient to provide protection for the majority of applications. 6.1. Programming the Eolis 3D to a motor (Figure G) The motor must have already been set and Do not program an Eolis 3D to several
- Take a remote control that is already programmed in the memory of the motor. programmed to a control point. motors.
- Press the PROG. button of the remote control, until the awning jogs.
- Briefly press the PROG. button (l) on the sensor: The motor will jog and the Eolis 3D is programmed to the motor. 6.2. Pre-defined threshold This setting corresponds to vibration detection of the awning according to pre-set values. This sensitivity is sufficient to provide protection for the majority of applications. Setting
(Figure H)
- Set the potentiometer (h) to the required the Pre-defined threshold threshold using a flat blade screwdriver:
- Threshold 1: light vibration will trigger the retraction of the awning.
- Towards threshold 9: stronger vibration will trigger the retraction of the awning.
- Insert the sensor (f) in the cover (e).
- Slide the sensor onto the bracket (g) until it hits the stop. Move the awning to simulate the vibration in order to check the setting. 6.3. Personalised threshold
- This setting corresponds to vibration detection based on a sensitivity threshold that has been set by the installer. The awning is manually shaken until automatic retraction is triggered: the strength of the vibration caused is recorded by the sensor. If the awning is not shaken before the automatic retraction, the sensor will return to the original configuration. 15/01/2016 09:04 7. Mode de fonctionnement
- Lapparition du vent engendre la vibration du store. Si la vibration est suprieure au seuil rgl, le store remonte automatiquement. Il est impossible:
- dempcher la remonte du store.
- de descendre le store pendant les 30 s qui suivent la remonte.
- Lorsque le capteur ne dtecte plus aucune vibration pendant 30s : il est alors possible de piloter lapplication en mode manuel. Si lEolis 3D est associ un capteur soleil et que le soleil apparat, alors le store descend automatiquement au bout de 12 min. Lors de forte bourrasque de vent et de journe ensoleill-
le, Somfy conseille de dsactiver la fonction Soleil pour protger au mieux votre store. 8. Rglages supplmentaires 8.1. Remplacement des piles (Figure F) Pendant le remplacement des piles, les rglages du capteur restent mmoriss. Ne jamais utiliser de piles rechargeables pour alimenter le capteur Eolis 3D !
- Retirer lensemble capteur (f) / couvercle (e) du support (g) et suivre la procdure du chapitre 5.4. Mise en place des piles.
- Remettre le capteur (f) dans son couvercle (e) puis glisser lensemble sur le support (g) jusquen but. 8.2. Suppression lEolis 3D dun moteur (Figure K) La procdure suivre pour la suppression de lEolis 3D WireFree RTS dun moteur est identique celle de lenregistrement : voir le chapitre 6.1. Enregistrement de lEolis 3D WireFree RTS un moteur. 8.3 Suppression de tous les capteurs La remise zro supprime tous les capteurs (soleil, vent, etc) associs au moteur du store !
- Prendre une tlcommande enregistre dans le moteur.
- Appuyer sur le bouton PROG. de la tlcommande, jusqu ce que le store effectue un va-et-vient.
- Faire un appui long (7 s) sur la touche PROG dun capteur associ ou non au moteur du store : le store effectue deux va-et-vient. Tous les capteurs sont supprims de la mmoire du moteur. Exercer un mouvement sur le store afin de contrler le rglage et le modifier si la sensibilit aux secousses est FR incorrecte. 6.3. Seuil personnalis
- Ce rglage correspond une dtection de secousses rgl par action secou manuelle-
lintensit partir dun seuil de sensibilit de ment des secousses provoques est enregistre par le capteur. Le remonte automatique linstallateur. la jusqu store est
:
Si aucune secousse nest mise avant la remonte auto-
matique, le capteur se retrouve en configuration dorigine. le rglage du seuil, Aprs le capteur passe en mode dmonstration lors des deux premiers cycles. Ce mode permet de modifier facilement le rglage slectionn. Un simple appui sur la touche STOP/My arrte la remonte du store et permet de modifier le seuil de sensibilit en renouvelant les secousses manuellement. 6.3.1. Rglage du Seuil personnalis (Figure I)
- Mettre le potentiomtre (h) sur 0 avec un tournevis plat.
- Insrer le capteur (f) dans le couvercle (e).
- Glisser lensemble sur le support (g) jusquen bute :
le capteur est en mode Seuil personnalis .
- Exercer un mouvement sur le store pour simuler le seuil maximal de vibration autorise et ce jusqu la remonte automatique du store : le capteur est rgl et passe en mode Dmonstration. Contrle du rglage :
- Descendre le store puis exercer des mouvements de vibration sur le store pour simuler le vent et provoquer la remonte du store :
- Si le store ragit de faon satisfaisante, le capteur est rgl correctement,
- Si le store ne ragit pas de faon satisfaisante, arrter la remonte du store en appuyant sur la touche STOP/My et passer ltape Modification du rglage du seuil personnalis. 6.3.2. Modification du rglage du Seuil personnalis
(Figure J)
- Descendre le store.
- Dsengager lensemble couvercle-capteur du support (g) et attendre 2 s.
- Enclencher lensemble couvercle-capteur sur le support :
le capteur est en mode Seuil personnalis . Si lensemble couvercle-capteur est dsengag du support pendant plus de 4 s, enclencher alors nouveau lensemble et rpter les deux tapes prcdentes.
-
Exercer un mouvement sur le store pour simuler le seuil maximal de vibration autorise et ce jusqu la remonte automatique du store : le capteur est rgl. 9. Astuces et conseils 9.1. Questions sur lEolis 3D?
DE Constats Aucune des LEDs sallume aprs la mise en place des piles. Le store ne remonte pas automati-
quement lapparition du vent. Le store remonte rgulirement alors quil ny a pas de vent. Causes possibles Les piles sont mal mises en place. Le capteur nest pas enregistr Le seuil est mal rgl. Le capteur ou le moteur est en panne. La rception radio est altre par des quipements radio externes Les piles sont faibles. Le capteur est mal insr dans le support. Le capteur est en panne. La connexion radio entre le capteur et le moteur ne marche pas. Solutions Vrifier le sens de montage des piles dans le capteur. Enregistrer le capteur au moteur, voir chapitre 6.1. Modifier le seuil, voir chapitre 6.2. ou 6.3. Secouer le store pour le faire remonter. Sil ne remonte pas, remplacer les piles voir chapitre 8.1. Sil ne remonte toujours pas, contrler le capteur et le moteur. Arrter les quipements radio au alentours. Remplacer les piles du capteur, voir chapitre 8.1. Enclencher le capteur dans le support jusquen bute. Remplacer les piles du capteur, voir chapitre 8.1. Si le store remonte toujours, remplacer le capteur. Remplacer les piles voir chapitre 8.1. Sil ne remonte toujours pas, contrler le capteur. Schlitzschraubendreher auf den gewnschten Grenzwert:
-
Grenzwert 1 : Schon schwaches Rtteln veranlasst die Markise zum Einfahren.
- In Richtung Grenzwert 9: Immer strkeres Rtteln ist erforderlich, um die Markise zum Einfahren zu veranlassen.
- Setzen Sie den Sensor (f) in das Gehuse (e) ein.
- Schieben Sie den Sensor bis zum Anschlag auf die Halterung (g). Bewegen Sie die Markise um berprfen Sie die Einstellungen, wenn die Empfindlichkeit auf Rtteln korrekt ist. 6.3. Individueller Grenzwert
- Der Installateur kann den Empfindlichkeitsgrenzwert fr das Erkennen von Rtteln einstellen. Dabei wird an der Markise wird manuell gerttelt, bis sie automatisch einfhrt: Die Intensitt des Rttelns wird vom Sensor gespeichert. Wenn vor dem automatischen Einfahren nicht gerttelt wird, werden die Werkseinstellungen des Sensors wieder aktiviert. Nach der Einstellung des Grenzwerts geht der Sensor bei den ersten beiden Zyklen in einen Demo-Modus. In diesem Modus kann die gewhlte Einstellung einfach gendert werden. Ein einmaliger Druck auf die STOP/My-Taste hlt das Einfahren der Markise an und ermglicht es, die Empfindlichkeitsgrenze durch erneutes manuelles Rtteln zu ndern. 6.3.1. Einstellung des
(Abbildung I)
- Drehen Individuellen Grenzwerts Potentiometer
(h) mit einem das Sie Schlitzschraubenzieher auf 0.
- Setzen Sie den Sensor (f) in das Gehuse (e) ein.
- Schieben Sie die Baugruppe bis zum Anschlag auf die Halterung (g):
Der Sensor ist jetzt im Modus Individueller Grenzwert.
- Bewegen Sie die Markise, um die Obergrenze fr die Schwingungen zu simulieren, und zwar solange, bis die Markise automatisch einfhrt: Der Sensor ist eingestellt und geht in den Demo-Modus. berprfung der Einstellung:
- Fahren Sie die Markise aus und simulieren Sie durch Rtteln an der Markise solange Wind, bis die Markise einfhrt:
- Wenn die Markise wie erwartet reagiert, ist der Sensor korrekt eingestellt.
- Wenn die Markise nicht wie erwartet reagiert, knnen Sie das Einfahren durch Druck auf die STOP/My-Taste anhalten und mit den Schritt nderung der Einstellung des individuellen Grenzwerts fortfahren. 6.3.2. nderung der Einstellung des individuellen Grenzwerts(Abbildung J)
- Fahren Sie die Markise aus.
- Entfernen Sie Gehuse und Sensor zusammen von der Halterung
(g) und warten Sie 2 s.
- Schieben Sie Gehuse und Sensor wieder auf die Halterung:
Der Sensor ist jetzt im Modus Individueller Grenzwert. Wenn Gehuse und Sensor lnger als 4 s von der Halterung 9. Tipps und Hinweise 9.1. Fragen zum Eolis 3D?
Fehler Nach dem Einsetzen der Batterien leuchtet keine der LEDs. Die Markise fhrt bei aufkommendem Wind nicht automatisch ein. Die Markise fhrt regelmig ein, obwohl kein Wind herrscht. Mgliche Ursachen Die Batterien sind falsch eingesetzt. Der Sensor ist nicht eingelernt Der Grenzwert ist schlecht eingestellt. Der Sensor oder der Antrieb ist defekt. Der Funkempfang wird durch externe Funkgerte gestrt. Die Batterien sind schwach. Der Sensor sitzt nicht richtig in seiner Halterung. Der Sensor ist defekt. Die Funkverbindung zwischen Sensor und Antrieb funktioniert nicht. Lsungen berprfen Sie die Richtung, in der die Batterien im Sensor eingesetzt sind. Lernen Sie den Sensor am Antrieb ein, siehe Abschnitt 6.1. ndern Sie den Grenzwert, siehe Abschnitt 6.2. oder 6.3. Rtteln Sie an der Markise, damit sie einfhrt. Wenn sie nicht einfhrt, sollten Sie die Batterien austauschen, siehe Abschnitt 8.1. Wenn sie immer noch nicht einfhrt, mssen Sie den Sensor und den Antrieb berprfen. Schalten Sie die Funkgerte in der Umgebung aus. Tauschen Sie die Batterien des Sensors aus, siehe Abschnitt 8.1. Schieben Sie den Sensor bis zum Anschlag auf die Halterung. Tauschen Sie die Batterien des Sensors aus, siehe Abschnitt 8.1. Wenn die Markise immer noch einfhrt, muss der Sensor ersetzt werden. Tauschen Sie die Batterien aus, siehe Abschnitt 8.1. Wenn sie immer noch nicht einfhrt, mssen Sie den Sensor berprfen. getrennt bleiben, schieben Sie die Baugruppe wieder auf und wiederholen Sie die beiden vorigen Schritte.
- Bewegen Sie die Markise, um die Obergrenze fr die Vibrationen zu simulieren, und zwar solange, bis die Markise automatisch einfhrt: Der Sensor ist eingestellt. 7. Funktionsweise
- Aufkommender Wind versetzt die Markise in Schwingungen. Wenn die Schwingungen den eingestellten Grenzwert berschreiten, fhrt die Markise automatisch ein. Es ist dann nicht mglich:
- das Einfahren der Markise zu verhindern.
- die Markise innerhalb von 30 s nach dem Einfahren wieder auszufahren.
- Wenn der Sensor 30 s lang keine Schwingungen mehr feststellt:
kann die Anwendung manuell gesteuert werden.
- Wenn der Eolis 3D mit einem Sonnensensor verknpft ist und die Sonne erscheint, fhrt die Markise nach 12 Minuten automatisch aus. Wenn es an einem sonnigen Tag zu heftigen Windben kommt, empfiehlt Somfy, die Sonnen-Funktion zu deakti-
vieren, um Ihre Markise bestmglich zu schtzen. 8. Zustzliche Einstellmglichkeiten 8.1. Austausch der Batterien (Abbildung F) des Sensoreinstellungen Die Batterietauschs gespeichert. Verwenden Sie fr die Versorgung des Sensors Eolis 3D keinesfalls wiederaufladbare Batterien!
bleiben whrend
- Nehmen Sie die Baugruppe Sensor(f) / Gehuse (e) von der Halterung (g) und folgen Sie den Anweisungen in Abschnitt 5.4. Einsetzen der Batterien.
- Setzen Sie den Sensor (f) wieder in das Gehuse(e) und schieben Sie beide zusammen bis zum Anschlag auf die Halterung (g). 8.2. Lschen des Eolis 3D aus einem Antrieb
(Abbildung K) Die Vorgehensweise fr das Lschen des Eolis 3D WireFree RTS aus einem Antrieb ist identisch mit dem Einlernen: Siehe Abschnitt 6.1. Einlernen des Eolis 3D WireFree RTS an einem Antrieb. 8.3 Lschen aller Sensoren Eine Rcksetzung auf Null lscht alle verknpften Sensoren
(Sonne, Wind usw.) aus dem Antrieb der Markise!
- Nehmen Sie einen im Antrieb eingelernten Funksender.
- Drcken Sie die PROG-Taste des Funksenders, bis die Markise mit einer kurzen Vor-/Zurck-Bewegung besttigt.
- An einem Sensor, der mit dem Antrieb der Markise verknpft ist oder nicht, lange (7 s) auf die Taste PROG drcken: Die Markise fhrt zwei kurze Vor-/Zurck-Bewegung aus. Alle Sensoren sind aus dem Speicher des Antriebs gelscht. H J h e f g 2 s. g I h e e K f g Veiller sparer les piles et batteries des autres types de dchets et les recycler via votre systme local de collecte. Die Batterien und Akkus von den restlichen Haushaltsabfllen trennen und entsprechend den geltenden Vorschriften im Handel oder den kommunalen Sammelstellen entsorgen. l Ensure batteries are separated from other types of waste and are recycled via your local recycling centre. After the threshold is set, the sensor will switch to EN demonstration mode for the first two cycles. This mode enables users to easily modify the selected setting. Pressing the STOP/My button once will stop the awning retracting and allow the user to modify the sensitivity threshold by manually shaking the awning. 6.3.1. Setting the Personalised threshold (Figure I)
- Turn the potentiometer (h) to 0 with a flat blade screwdriver.
- Insert the sensor (f) in the cover (e).
- Slide the assembly onto the bracket (g) until it hits the stop:
the sensor is in Personalised threshold mode.
- Move the awning to simulate the threshold for the maximum vibration permitted, and continue until the awning automatically retracts: the sensor is set and will switch to Demonstration mode. Checking the setting:
- Extend the awning, then shake it to simulate vibration by the wind to cause the awning to retract:
- If the awning reacts as required, the sensor has been correctly set,
- If the awning does not react as required, stop the retraction of the awning by pressing the STOP/My button and go to the step entitled Modifying the personalised threshold setting. 6.3.2. Modifying the Personalised threshold setting
(Figure J)
- Extend the awning.
- Detach the cover-sensor assembly from the bracket (g) and wait for 2 seconds.
- Fit the cover-sensor assembly onto the bracket: the sensor is in Personalised threshold mode. If the cover-sensor assembly is detached from the bracket for more than 4 seconds, tre-engage the assembly and repeat the two previous steps.
- Move the awning to simulate the threshold for the maximum vibration permitted, and continue until the awning automatically retracts: the sensor has been set. 7. Method of operation
- Wind will cause the awning to vibrate. If the vibration is greater than the set threshold, the awning will automatically retract. It is impossible:
- to prevent the awning from retracting.
- to extend the awning wait for 30 seconds after the awning has retracted.
- When the sensor stops detecting any vibration for 30 seconds: the application can be controlled in manual mode.
- If the Eolis 3D is connected to a sun sensor and the sun comes out, then the awning will extend after 12 mins. On gusty, sunny days, Somfy recommends that the Sun function be deactivated to better protect your awning. 8. Additional settings 8.1. Battery replacement (Figure F) When the batteries are replaced, the sensor settings will remain memorised. Never use rechargeable batteries for the Eolis 3D sensor!
Remove the sensor (f) / cover assembly (e) from the bracket
(g) and follow the procedure in section 5.4. Fitting the batteries.
- Refit the sensor (f) in the cover (e) and slide the assembly onto the bracket (g) until it reaches the stop. 8.2. Deleting an Eolis 3D from a motor (Figure K) The procedure for deleting the Eolis 3D WireFree RTS from a motor is identical to the programming procedure: see section 6.1. Programming the Eolis 3D WireFree RTS to a motor. 8.3 Deleting all sensors Resetting deletes all sensors (sun, wind, etc.) connected to the awning motor!
- Take a remote control that is already programmed in the memory of the motor.
- Press the PROG. button of the remote control, until the awning jogs.
- Press and hold (7 seconds) the sensor PROG button (the sensor does not have to be linked to the awning motor): the awning will jog twice. All the sensors have been deleted from the motors memory. 9. Tips and recommendations 9.1. Questions on the Eolis 3D?
Observations None of the LEDs come on after the batteries are fitted. The awning does not automatically retract when the wind increases. Possible causes The batteries are incorrectly fitted. The sensor is not programmed The threshold is incorrectly set. The sensor or the motor is out of order. Solutions Check the direction in which the batteries are inserted into the sensor. Program the sensor to the motor, see section 6.1. Modify the threshold, see section 6.2. or 6.3. Shake the awning to make it retract. If it does not retract, replace the batteries (see section 8.1). If it still does not retract, check the sensor and the motor. Observations The awning does not automatically retract when the wind increases. Possible causes External radio equipment is interfering with the radio reception Solutions Turn off all radio equipment nearby. The awning frequently retracts when there is no wind. The batteries are low. Replace the sensor batteries, see section 8.1. The sensor is incorrectly inserted in the bracket. Engage the sensor in the bracket until it reaches the stop. Replace the sensor batteries, see section 8.1. If the awning still retracts, replace the sensor. Replace the batteries
(see section 8.1). If it still does not retract, check the sensor. The sensor is not operating. The radio connection between the sensor and the motor is not working. This device complies with Part 15 of the FCC Rules. Operation is subject following the two to conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, inclu-
ding interference that may cause undesired operation. Warning !
Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment. 5050583D Eolis-3D-RTS-FR-DE-EN.indd 2 15/01/2016 09:04
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2016-04-26 | 433.42 ~ 433.42 | DSC - Part 15 Security/Remote Control Transmitter | Change in identification of presently authorized equipment. Original FCC ID: PUDTRANSHZ003 Grant Date: 03/31/2016 |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2016-04-26
|
||||
1 | Applicant's complete, legal business name |
Somfy Systems
|
||||
1 | FCC Registration Number (FRN) |
0006579940
|
||||
1 | Physical Address |
121 Herrod Blvd
|
||||
1 |
Dayton, New Jersey 08810
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
t******@timcoengr.com
|
||||
1 | TCB Scope |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
DWN
|
||||
1 | Equipment Product Code |
WF3DB
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
J**** P******** H********
|
||||
1 | Title |
Industrial Operations Manager
|
||||
1 | Telephone Number |
609 3******** Extension:
|
||||
1 | Fax Number |
609-4********
|
||||
1 |
j******@somfy.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DSC - Part 15 Security/Remote Control Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Wire Free RTS US Eolis 3D | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Change in identification of presently authorized equipment. Original FCC ID: PUDTRANSHZ003 Grant Date: 03/31/2016 | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Advanced Compliance Laboratory
|
||||
1 | Name |
W**** L********
|
||||
1 | Telephone Number |
908-9********
|
||||
1 | Fax Number |
908-9********
|
||||
1 |
w******@aol.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15.231 | 433.42000000 | 433.42000000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC