all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
User manual | Users Manual | 247.17 KiB | / February 09 2009 | |||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | External Photos | / February 09 2009 | ||||||
1 | Internal Photos | / February 09 2009 | ||||||
1 | ID Label/Location Info | |||||||
1 | Cover Letter(s) | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos | / February 09 2009 |
1 | User manual | Users Manual | 247.17 KiB | / February 09 2009 |
3-873-945-12 (1) Digital Wireless Transmitter The supplied CD-ROM includes the Operating Instructions for the DWT-B01 digital wireless transmitter (English, French, German, Italian, Spanish, and Japanese versions) and the frequency lists (English and Japanese versions) in PDF format. For more details, see Using the CD-ROM manual on page 21. Operating Instructions Before operating the unit, please read this manual thoroughly and retain it for future reference. DWT-B01 2008 Sony Corporation F WARNING Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. For the customers in the U.S.A. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.
- Consult the dealer or an experienced radio/TV technician for help. All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules. If you have any questions about this product, you may call;
Sony Customer Information Service Center 1-800-222-7669 or http://www.sony.com/
Declaration of Conformity Trade Name: SONY Model: DWT-B01(F) Responsible Party: Sony Electronics Inc. Address: 16530 Via Esprillo, San Diego, CA 92127 U.S.A. Telephone Number: 858-942-2230 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Notice for customers in the U.S.A. Use of Sony wireless devices is regulated by the Federal Communications Commision as described in Part 74 subpart H of the FCC regulations and users authorized thereby are required to obtain an appropriate license. IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted, Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void users authority to operate this device. This device complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This device has very low levels of RF energy that it is deemed to comply without testing of specific absorption radio (SAR). For customers in Canada This Class B digital apparatus complies with Canadian ICES-003. For the customers in Canada Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The term IC before the radio certification number only signifies that Industry Canada technical specifications were met. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. This device has been designed to operate with an antenna having a maximum gain of 0 dB. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. Notice for customers in Canada:
Use of Sony wireless devices is regulated by the Industry Canada as described in their Radio Standard Specification RSS-123. A licence is normally required. The local district office of Industry Canada should therefore be contacted. When the operation of the device is within the broadcast band, the licence is issued on no-interference, noprotection basis with respect to broadcast signals. For the customers in Europe If the transmitter develops an abnormally high temperature, a burning odor or smoke during use, remove the battery holder and stop using the transmitter immediately. Take care not to burn your fingers when removing the battery holder as the batteries may be very hot at this time. AVERTISSEMENT Nexposez pas les batteries une chaleur excessive, au soleil ou prs dun feu par exemple. Pour les utilisateurs au Canada Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Lutilisation doit rpondre aux deux conditions suivantes : (1) ce matriel ne doit pas provoquer de brouillage et (2) il doit accepter tout brouillage, mme celui qui est susceptible daffecter son fonctionnement. La mention IC: devant le numro de certification/ homologation signifie uniquement que les spcifications techniques dIndustrie Canada sont remplies. Pour rduire les interfrences radio potentielles pour les autres utilisateurs, le type dantenne et son gain doivent tre choisis de sorte que la puissance isotrope rayonne quivalente (PIRE) ne soit pas suprieure la puissance requise pour assurer la communication. Ce dispositif a t conu pour fonctionner avec une antenne gain maximum de 0 dB. L'emploi dune antenne gain suprieur est strictement interdit par les rgles dIndustrie Canada. Limpdance dantenne requise est de 50 ohms. Remarque lintention des utilisateurs au Canada:
Lusage des appareils sans fil Sony est rglement par lIndustrie Canada comme dcrit dans leur Cahier des Normes Radiolectriques CNR-123. Une licence est normalement requise. Le bureau de lIndustrie Canada doit tre contact. Lorsque le fonctionnement de lappareil respecte les limites de la bande de radiodiffusion, la licence est accorde sur la base dune non-interfrence, non-
protection pour les signaux de radiodiffusion. Pour les clients en Europe Si lmetteur dgage une temprature anormalement leve, une odeur de brl ou de la fume pendant son utilisation, enlevez le support de piles et arrtez toute utilisation immdiatement. Attention ne pas vous brler les doigts lorsque vous retirez le support de piles car cellesci peuvent tre brlantes. WARNUNG Akkus drfen keinesfalls bermiger Wrmeeinwirkung ausgesetzt werden, wie z.B. Sonneneinstrahlung, Feuer o. Fr Kunden in Europa Wenn der Sender eine abnorm hohe Temperatur, einen Geruch nach Verbranntem oder Rauch entwickelt, entnehmen Sie den Batterie-Halter und stoppen Sie sofort den Betrieb des Senders. Achten Sie bei der Entnahme des Batterie-
Halters darauf, sich nicht die Finger zu verbrennen, denn die Batterien knnten sehr hei zu diesem Zeitpunkt sein. AVVERTENZA Le batterie non devono essere esposte a fonti di calore eccessivo come luce solare diretta, fuoco, ecc. Per i clienti in Europa Se il trasmettitore si surriscalda eccessivamente, rilascia odore di bruciato o del fumo, rimuovere il porta-pile e smettere di usare il trasmettitore immediatamente. Fare attenzione a non bruciarsi le dita quando si rimuove il porta-pile poich le pile potrebbero essere molto calde. ADVERTENCIA No se deben exponer las bateras a una fuente de calor excesivo como la luz del sol, el fuego o similar. Para los clientes de Europa Si el transmisor desprende temperaturas altas no normales, olor a quemado o humo durante su uso, quite el soporte de las pilas y detenga el uso del transmisor inmediatamente. Tenga cuidado de no quemarse los dedos cuando quite el soporte de las pilas pues las pilas pueden estar bastante calientes en este momento. This model has an RF module of the FCC/IC approval built-in. BUILT IN MODULE RM-215 FCC ID: AK8RM215 IC: 409B-RM215 For the customers in the U.S.A. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. U.K. Germany Norway Luxembourg Belgium Denmark France Italy Sweden Switzerland Finland Iceland Turkey 470 - 862 MHz 470 - 606 MHz, 614 -
862 MHz 800 - 820 MHz 470 - 862 MHz 470 - 862 MHz 800.100 - 819.900 MHz 470 - 830 MHz 470 - 854 MHz 470 - 862 MHz 790 - 862 MHz 790.100 - 821.900 MHz, 854 - 862 MHz 470 - 862 MHz 470 - 862 MHz Features The DWT-B01(F) is a digital wireless transmitter for a UHF synthesized wireless microphone system to be used for broadcast or movie production purpose. This transmitter is suitable for Electronic News Gathering (ENG) and Electronic Field Production (EFP). What are the strengths of a Digital Wireless Microphone System?
This system has the following special features and qualities:
High-quality audio signal transmission approaching to the quality of wired microphone Extremely tolerant to interference waves and secure wireless transmission Simultaneous multi-channel operation Encrypted transmission Metadata transmission. Note that the DWT-B01(F) digital wireless transmitter cannot be used to transmit to analog wireless receivers. The features of this transmitter are described below. Wide RF carrier frequency range The DWT-B01(F) transmitter covers an extremely wide RF carrier frequency range. US models can cover a 66-MHz band and 60-MHz band respectively much wider than 24-
MHz of the analog wireless microphone system, while the CE6267 model
(European model) can cover a 48-MHz band. This remarkably wide coverage on a single model offers cost efficiency and operational convenience, because it allows one transmitter to be operated in many different areas. Compact, lightweight, and rugged design The DWT-B01(F) is designed to be extremely compact and lightweight, essential qualities for use by artists in fast-moving TV and outdoor productions. Switchable mic or line input level and adjustable attenuator The audio input level of the DWT-B01(F) is selectable from either MIC or LINE. When MIC is selected, the attenuator can be adjusted in 3-dB steps from 0 dB to 48 dB. The reference input level of the MIC and LINE is 58 dBu (60 dBV) and +4 dBu, respectively. Selectable RF output power:
1 mW, 10 mW, and 50 mW The 1 and 10 mW output is suitable for multi-channel operations, while the 50 mW output is intended for long-distance. Power sleep mode The DWT-B01(F) is equipped with a power sleep/wake up mode that can be wirelessly controlled from the optional DWR-S01D receiver. Digital low-cut filter Equipped with a digital low-cut filter, the DWT-B01(F) can reduce the effects of undesired ambient noise. after use. Lengthy use of the transmitter in such places or not cleaning it after its use in such places may shorten its life. Clean the surface and the connectors of the transmitter with a dry, soft cloth. Never use thinner, benzene, alcohol or any other chemicals, since these may mar the finish. Notes on simultaneous multi-
channel operation Keep the transmitter at least 30 centimeters (11 7/8 inches) away from another transmitter. Keep the transmitter at least 4 meters (13 feet) away from the antenna of a receiver when only digital wireless microphones are being used, or 6 meters (20 feet) when a mixture of digital and analog microphones is being used. This system should be kept at least 100 meters (328 feet) away from any analog wireless systems using the same frequency when both are being used in a wide area with no walls or obstructions. If you experience noise, increase the distance between the transmitter and receiver or decrease the transmission power on the transmitter. Note on microphone and transmitter combinations The transmission signal may cause noise on some microphones. If you experience noise, you may be able to reduce it by changing the position of the microphone cable, moving the microphone connection away from the antenna, or lowering the transmission power. Important notes on operation Notes on using the transmitter The digital wireless microphone system product must be used within a temperature range of 0C to 50C (32F to 122F). Operating the transmitter near electrical equipment (motors, transformers, or dimmers) may cause it to be affected by electromagnetic induction. Keep the transmitter as far from such equipment as possible. The presence of the lighting equipment may produce electrical interference over the entire frequency range. Position the transmitter so that interference is minimized. To avoid degradation of the signal-to-
noise ratio, do not use the transmitter in noisy places or in locations subject to vibration, such as the following:
- near electrical equipment, such as motors, transformers or dimmers
- near air conditioning equipment or places subject to direct air flow from an air conditioner
- near public address loudspeakers
- where adjacent equipment might knock against the tuner Keep the transmitter as far from such equipment as possible or use buffering material. On cleaning If the transmitter is used in a very humid or dusty place or in a place subject to an active gas, clean its surface as well as the connectors with a dry, soft cloth soon Easy-to-see, full dot-matrix OLED (Organic Light-Emitting Diode) Display The quick response of the OLED display enables real-time operating conditions to be displayed clearly and accurately. Parts identification a Antenna b AF (audio input level) /PEAK indicator Lights up green when the signal input is stronger than the reference level. Lights up red when the signal input is 3 dB below the level at which distortion begins. c POWER indicator Lights up green when the transmitter is turned on. When the battery is exhausted, the indicator starts flashing. d Audio input connector (SMC9-4S) Connects the output plug from the optional lavalier microphone. This connector also accepts the input from another wired microphone connected through the supplied microphone cable, or the audio output from a mixer, etc. using key operations. By connecting the digital wireless receiver to this connector with the supplied USB cable, you can exchange the encryption key for encrypted transmission function. To connect a microphone j Display section Microphone (optional) To secure the microphone cable connection, be sure to turn and lock the connector cover. e + or button Selects functions or values shown on the display. Holding down the button while switching on the transmitter activates the pairing operation for the wireless remote control function. f POWER switch Turns the transmitter ON or OFF. g Battery compartment Accommodates two LR6 (size AA) alkaline batteries. For details on how to insert the batteries, see Power supply . h SET button Adjusts displayed function settings and enters the value. Holding down the SET button while switching on the power turns the transmitter on without sending a signal. i USB connector (Micro USB) Use this connector to connect an optional USB keyboard to carry out menu functions A RF transmission indication Indicates the current transmission status.
: Currently transmitting
: Transmission stopped B RF (radio frequency) transmission power indication Indicates the current transmission power setting. You can change the setting with the RF transmission power setting function. H: transmitting at 50 mW M: transmitting at 10 mW L: transmitting at 1 mW C Audio input level meter Indicates the input signal level of the audio input connector D Reference level gauge Indicates the reference input level. When the attenuation is 0 dB with the input level set to mic, 58 dBu (60 dBV) is indicated. When the line level is set, +4 dBu is indicated. E Peak indicator Warns of excessive input by lighting up when the signal is 3 dB below the level at which distortion begins. F Power switch lock indicator Indicates that the power switch is locked, preventing the transmitter from being accidentally turned off or on. For details, see Locking the power switch (POWER SW LOCK) . G Wireless remote control condition indication Indicates the signal transmission condition of the wireless remote control function (4 levels).
: Good transmission
: Somewhat good transmission
: Somewhat poor transmission
: Poor transmission
: Unable to communicate with paired receiver When the wireless remote control function is off, this indication does not appear. H Battery indication Shows the battery condition. For details, see Battery indication on page 18. I Menu display section The status of 16 different functions are displayed here. To select the function, press the + or button repeatedly. For details, See Setting menus . Power supply The transmitter can operate on two LR6
(size AA) alkaline batteries continuously for about 3.5 hours at 25C (77F). Installing the batteries 1 Squeeze the battery-holder tabs inward
(in the direction of the arrows) and slide out the battery holder. 2 Insert new batteries, making sure the polarities are correct, and then return the battery holder to its original position. Battery indication The power status is indicated by eight level indications. Replace both batteries when the battery indication starts to flash. Be sure to check the expiration date printed date on the new batteries before using them. Note The indication is based on the use of new LR6 (size AA) Sony Alkaline batteries. An incorrect indication may result when a different kind of batteries, a different brand of batteries or old batteries are used. If you plan to use the transmitter for a long period of time, it is recommended that you replace the batteries with brand new ones. Setting the transmission channel This transmitter allows the free selection of any transmission channel. The transmitter provides groups of interference-free channels. When using multiple microphones and transmitters at the same time (simultaneous multi-channel operations) within the same area, selecting the same group and using a channel within that group can prevent signal interference. To set the transmission channel on the transmitter, first you select the group and channel using the RF indicator and scanning functions on the receiver. Next you set the group and channel parameters to match the setting on the receiver. Selecting the group/
channel Notes Before doing this procedure, use the BAND function to set the transmitter to the bandwidth of the receiver you are using. The setting for this function cannot be changed during actual signal transmission. Set the transmitter group (GP) and channel
(CH) as follows:
For details on groups and channels, refer to Sony Digital Wireless Microphone System Frequency Lists on the supplied CD-ROM. For details on menu operation, see Basic menu operations . 1 Turn off the power, and then while holding down the SET button, turn the power on. The signal transmission stops. 2 Press the + or button repeatedly until the GP/CH indication is displayed. 3 Hold down the SET button until the item to be set flashes. 4 Press the + or button repeatedly to select a group. 5 Press the SET button to enter the group. The channel indication starts flashing. 6 Press the + or button repeatedly to select a channel. 7 Press the SET button to enter the channel. To set the group/channel using the pairing mode of the wireless remote control function When the transmitter is paired with the receiver, the transmission channel of the transmitter is set to the receiving channel on the receiver automatically. For details, seePairing with a receiver . Using the wireless remote control function This transmitter is equipped with a wireless remote control function that can be used to set the parameters (low-cut filter, attenuation operation, power save mode, etc.) of the transmitter through the receiver or other devices. This function makes it easier to operate and manage the microphone system while in the field. This wireless control is 2.4 GHz IEEE802.15.4 compliant and has no effect on the RF band of digital wireless audio. This function is activated when pairing is established between the transmitter and the receiver using the RF REMOTE function. Pairing must be done first before the wireless remote control function can be used. Pairing with a receiver Pairing links the transmitter with the receiver which the wireless remote control function is to be used. When the transmitter has been paired with a receiver through the receiver operation, turning on the transmitter while holding down the button establishes the pairing immediately. To carry out pairing through menu operations on the transmitter, do the following. 1 Set the receiver to be used for controlling the transmitter to pairing mode. RF transmission power setting Attenuator for the audio input setting Low-cut filter setting Power save setting For details on menu operation, see Setting menus. To cancel the wireless remote control function In the RF REMOTE indication, select OFF. Notes on the wireless remote control function The wireless remote control function on the transmitter uses the 2.4-GHz band and may thus be subject to interference from other devices. When pairing fails (Pairing fail is displayed), successful communication between the transmitter and the receiver has not occurred within a given amount of time. Pairing may be harder to do when another receiver is engaged in pairing nearby. When it becomes hard to use the remote control, the remote control may be improved by switching the wireless remote control function off, then on again in the RF REMOTE display, then re-
pairing with the transmitter (change to a channel with less interference). For details, refer to the operating instructions supplied with the receiver. 2 Press the + or button repeatedly until the RF REMOTE indication is displayed. 3 Hold down the SET button until the item to be set flashes. 4 Press the + or button repeatedly to select PAIRING. 5 Press the SET button to enter. The transmitter sends a pairing request to the receiver which is on pairing mode. Before established pairing, if you press any operation key on the transmitter, pairing mode will be cancelled. When pairing has been established, the wireless remote control condition level
(indicated by REMOTE turns on, and the remote control function becomes operative.
) goes up, RF To use the wireless remote control function with a previous pairing In the RF REMOTE indication, select ON. Notes When you set RF REMOTE to ON, the transmitter will communicate with the receiver to which it was previously paired. To use the wireless remote control function with another receiver, you must perform the pairing procedure for that receiver. Multiple transmitters cannot be paired with the same receiver. The following transmitter settings can be done from the wireless remote control:
Group/channel/BAND setting The encryption key used by the transmitter and receiver is newly generated for each key transmission, resulting in highly secure communication. The encryption key used between the transmitter and the receiver is saved when the power is turned off, so the encrypted transmission can be resumed the next time the power is turned on. 1 Preparing the transmitter (this unit) 1 Hold down the SET button until the item to be set flashes in ENCRYPTION indication on the transmitter. 2 Press the + or button repeatedly to select SECURE KEY, and then press the SET button. 2 Preparing the receiver Select SECURE KEY on the receiver that receives the encryption key. For details on receiver operations, refer to the operating instructions supplied with the receiver. 3 Exchanging the encryption key On the receiver, select USB or REMOTE (wireless remote) as the method for encryption key exchange. When the RF REMOTE function is off, REMOTE cannot be selected. When you select USB:
Connect the transmitter to the receiver with the supplied USB cable and USB adapter cable. Using the encrypted transmission function To prevent hacking of the signal, the transmitter scrambles the signal during transmission. To use this function, select one of the following encrypted transmission modes:
Secure key mode: An encryption key that is automatically generated by the transmitter is used by both the transmitter and receiver in this one-to-one encrypted transmission method. Password mode: You choose a password of up to eight characters that can be set for multiple transmitters and receivers. This enables encrypted transmission within a group. Note Make sure the same mode is set on the transmitter and receiver. Using secure key mode
(SECURE KEY) Use this mode for one-to-one encrypted transmission between one transmitter and one receiver. An encryption key that cannot be read from the outside is automatically generated by the transmitter. This key is transmitted to the receiver through a USB connection or the RF REMOTE function, enabling encrypted transmission to take place. 2 Press the + or button repeatedly to select PASSWORD, and then press the SET button. 3 Input a password of up to eight characters on the transmitter. To enter a password, use the procedure described in Naming of transmitter (NAME). 4 Set the encrypted transmission function setting on the receiver to PASSWORD. 5 Set the same password that was set on the transmitter. For details on receiver operations, refer to the operating instructions supplied with the receiver. Note It is recommended that you change the password periodically. USB cable (supplied) USB adapter cable
(supplied) For details on receiver operations, refer to the operating instructions supplied with the receiver. When you select REMOTE:
The transmitter searches for a receiver that it has been paired with. After the transmitter detects the receiver, the transmitter exchanges the encryption key with receiver and encrypted transmission begins. Using password mode
(PASSWORD) Set this mode when multiple transmitters are paired with multiple receivers for encrypted transmission. If both transmitters and receivers are set with the same user-designated password, the audio signal can be decoded. This mode is useful when multiple transmitters and receivers are used as a single group, or when the audio signal from one transmitter is received by multiple receivers at the same time. 1 Hold down the SET button until the item to be set flashes in the ENCRYPTION indication on the transmitter. Characters that can be entered from a USB keyboard: (space), 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R, S, T, U, V, W, X, Y, Z, !,
(Passwords may consist of the numbers 0 to 9 and letters A to Z only.) Special key: Backspace (BS) and Delete
(DEL) keys. Notes The number keys on the keyboard cannot be used. This transmitter is compatible with English-language keyboards only. USB keyboards with multiple functions, such as USB hub and pointing device, cannot be used. Power to the connected keyboard is supplied by the USB connector on the transmitter. The power rating is 100 mA. Keyboards that consume more power than that cannot be used. Do not leave the transmitter connected to the keyboard when not in use. If you do, the batteries in the transmitter will be drained more quickly. Text editing should be done with the alphabet, BS, DEL, and Enter keys. Using a USB keyboard Connecting an optional USB keyboard to the transmitter allows you to perform menu operations and enter your name and password for the encrypted transmission function from the keyboard. A Micro USB connector is used on the transmitter. For this reason, use the supplied USB adapter cable. USB adapter cable (supplied) Menu operations with a USB keyboard You can use a USB keyboard to perform the same menu operations that you do on the transmitter. The transmitter buttons correspond to the following keys on a USB keyboard:
Buttons on the transmitter SET
USB keyboard ENTER R r To enter a text With a USB keyboard, you can enter names and passwords for encrypted transmissions. Basic menu operations Function name BRIGHTNESS (display brightness) setting DIMMER MODE (automatic dimming of the display) setting FACTORY PRESET (factory setting) function VERSION (software version) indication Item to be set 1 Press the + or button repeatedly until the function to be set appears. 2 Hold down the SET button until the item to be set flashes. 3 Press the + or button to change the setting. 4 Press the SET button to enter the setting. Types of menu:
NAME (transmitter name) setting BAND (frequency band) selection GP/CH (group/channel) selection RF POWER (RF transmission power) setting INPUT LEVEL (audio input level) setting LCF (low-cut filter) setting POWER SAVE setting TIME (accumulated use time) indication ENCRYPTION (encrypted transmission function) setting INTERNAL SG (internal signal generator) POWER SW LOCK (power switch lock) function RF REMOTE (wireless remote control) function Setting menus Selecting the group/
channel (GP/CH) The factory settings are as follows:
The functions and parameters of the settings menu are explained here. Underlined items are the factory setting. US models 00 Gp Naming of transmitter
(NAME) You can specify a transmitter name of up to 16 characters. The factory setting for the transmitter name is the model name and serial number. The transmitter name is sent to the receiver as metadata and is used by the receiver to distinguish between different transmitters.
+: The first press on the + button displays the character set. You can then use the + and buttons to select the desired character. And then, pressing the SET button adds the selected character to the end of the current name.
: Deletes the last character in the current name. SET: Enters the character or edited name. Note You cannot insert or delete a character in the middle of the name. To edit with a keyboard You can enter data from an optional keyboard connected to the USB connector. For details, see Using a USB keyboard. European model 00 Gp For details, see Selecting the group/channel. Selecting the frequency band (BAND) Matches the frequency range on this transmitter to that of the Sony digital wireless receiver. The frequency range that can be set for the optional receiver combined with this transmitter differs as follows:
US models Example:3040U TV30-33, TV34-36, TV38-41 Not available for TV37 European model 6267CE TV62-64, TV67-69 Not available for TV65 and TV66 For details about the frequency range of each band, refer to Sony Digital Wireless Microphone System Frequency Lists on the supplied CD-ROM. Note The setting for this function cannot be changed during actual signal transmission. To change the setting, turn off the transmitter first. Then, while holding down the SET button, turn the power on. Then change the setting after the signal transmission has stopped. Setting the RF Output Power (RF POWER) You can set the RF output power. 1 mW (LOW): transmitted by 1 mW 10 mW (MID): transmitted by 10 mW 50 mW (HIGH): transmitted by 50 mW Using wireless remote control, this function can be controlled from the receiver and other devices. Note The setting for this function cannot be changed during actual signal transmission. To change the setting, turn off the transmitter first. Then, while holding down the SET button, turn the power on. And then, change the setting after the signal transmission has stopped. Setting the audio input level (INPUT LEVEL) You can set the input level to an analog head amp. Select LINE or MIC, depending on the audio source connected to the audio input connecter. When MIC is selected, the ATT
(attenuation) level will flash next. With the microphone connected, speak into the microphone as you monitor the input level meter and press the + or button repeatedly to select the appropriate attenuation level. The reference levels for the various settings are as follows:
Input MIC LINE Attenuation
(dB) 0 3 6 9 3 dB step 45 48 Reference input level (dB) 58 55 52 49 3 dB step 13 10
+4 Maximum input level (dBu) 22 19 16 13 3 dB step
+23
+24
+24 Headroom (dB) 36 34 20 With the wireless remote control function, the attenuation level can be changed from the receiver and other devices. Low-cut filter setting (LCF) The frequency of the low-cut filter can be set. OFF: Turns off the low-cut filter. 20 30 40 50 60 70 80 90 100 120 140 160 180 200 220 (Hz):
Low-cut filter is set according to the selected frequency. Using wireless remote control, this function can be controlled from the receiver and other devices. Power save setting (POWER SAVE) To conserve power, this setting allows you to put all transmitter functions to sleep. ACTIVE: The transmitter operates normally. SLEEP: The sleep function is on. During sleep, the POWER indicator flashes at 2-
second intervals. To change back to normal operation During sleep, press the SET, +, or button. You can also use the wireless remote control to change the receiver back to normal operation. For details on wireless remote control function, see Using the wireless remote control function. Displaying the accumulated use time (TIME) You can display the accumulated battery use time as a rough estimate of total transmitter usage. The factory setting is 00:00. To reset the accumulated time indication 1 Hold down the SET button until the time indication flashes. 2 Press the button so 00:00 RESET appears, and then press the SET button. Setting the encrypted transmission function
(ENCRYPTION) You can set the encrypted transmission function. SECURE KEY: Sets the secure key method. PASSWORD: Sets the password method. OFF: The encrypted transmission function is not used. For details, see Using the encrypted transmission function. Generating an internal signal (INTERNAL SG) This transmitter generates a 1-kHz reference level sine wave that can be used to adjust or check the audio level of the receiver or the system that you are using. This internal signal is outside the control of the attenuator. 1 kHz: A 1-kHz internal signal is generated. OFF: An internal signal is not generated. Note If the transmitter is turned off while the reference signal function is on, the function will turn off automatically. Locking the power switch
(POWER SW LOCK) The power switch can be locked to prevent the transmitter from being accidentally turned off or on. Even when the power switch is locked, all parts of the transmitter other than the power switch remain functional. UNLOCK: The power switch is not locked. LOCK: The power switch is locked. When LOCK is selected, the power switch lock icon appears in the display. ALWAYS ON: The display stays on at the brightness level set with the BRIGHTNESS function. Resetting parameters to their factory settings
(FACTORY PRESET) All parameter settings can be returned to their factory settings. Holding down the SET button until a message appears asking for confirmation. Press the + or button repeatedly to select YES, and then press the SET button to enter. The transmitter parameters are reset to their factory settings. Note The setting for this function cannot be changed during actual signal transmission. To change the setting, turn off the power first. Then while holding down the SET button, turn the power on. Then change the setting after the signal transmission has stopped. Displaying the software version (VERSION) The version of the transmitter software can be displayed. Wireless remote control function (RF REMOTE) This function must be set to allow the wireless remote control function to be used between the transmitter and receiver. OFF: Stops the wireless remote control function. ON: Starts the wireless remote control function with the previously paired receiver. PAIRING: Executes a new pairing. For details, see Pairing with a receiver. Setting the brightness of the display (BRIGHTNESS) Ten levels of brightness can be selected for the organic light-emitting diode display. The selectable settings are the following:
(Dark) 1 2 3 4 5 6 7 8 9 10 (Bright) Automatic dimming of the display (DIMMER MODE) The organic light-emitting diode display can be set to dim or turn off after a certain amount of time. AUTO OFF: The display turns off after 30 seconds. The display goes on again when you press the SET, +, or button. AUTO DIMMER: The display dims after 30 seconds. The display becomes bright again when you press the SET, +, or button. Clasp Attaching with the soft case The transmitter can be attached to the user with the supplied soft case. All operations are possible when the transmitter is attached with the soft case. The clip can be attached to the soft case at an angle of 0, 90, 180, or 270 degrees, allowing you to attach the transmitter in a variety of positions. Removing the clip Remove the transmitter from the soft case before attaching or removing the supplied clip. 1 Remove the transmitter from the soft case. 2 Insert your fingers between the clip and the soft case as shown in the illustration and pull the clip in the direction of the arrow. 3 Press down on the clasp as shown in the illustration and slide the clip in the direction of the arrow. Troubleshooting If you encounter a problem using this transmitter, use the following checklist to find a solution. For any problems with the receiver or adapter, refer to the operating instructions supplied with the respective device. If the problem persists, consult your Sony dealer. Symptom The transmitter does not turn on. Meanings The batteries are inserted backwards in the battery compartment. The batteries are exhausted. The batteries drain quickly. Interruptions in the reception occurs. There is no sound. The sound is weak. Manganese batteries are being used. The transmitter is being used under cold conditions. The transmitter is too far from the receiver. The transmission power setting is set to L: 1mW. The channel setting on the transmitter is different from that on the receiver. The setting of the encrypted transmission function on the receiver is different from that on the transmitter. The audio input level of the transmitter is set to LINE or the attenuation level is too high. There is distortion in the sound. The attenuator is set too low for the audio input level of the transmitter. The bass is weak. The frequency of the low-cut filter is set too high. Remedy Reinsert the batteries with the correct orientation. Replace the batteries with new ones. Use alkaline batteries. The batteries drain quickly under cold conditions. Decrease the distance to the receiver and check the reception. Increase the transmission power. Use the same channel setting on both the transmitter and receiver. Confirm that the setting of the encrypted transmission function is the same on both the transmitter and the receiver. If a microphone is connected to the transmitter, set the audio input to MIC. While monitoring the audio input level meter, set the attenuator to an appropriate level. While monitoring the audio input level meter, set the attenuator to a level that does not produce distortion. While monitoring the sound, decrease the low-cut filter frequency to a level that produces the proper sound quality. Symptom There is too much bass. The power does not turn off even though the power switch is turned to OFF. Wireless remote control is not possible. The USB keyboard does not work. The display is too dark. Meanings The microphone connected to the transmitter produces excessive bass because the frequency response of the transmitter extends into the low 20-Hz range. The power switch is locked. Remedy Use the low-cut filter to cut the bass. Turn off the POWER SW LOCK function. Pairing has not been established between the transmitter and receiver. The receiver is too far from the transmitter for communication to occur. The transmitter that was paired with the receiver has been paired with another receiver. You are using a USB keyboard that is not compatible with the transmitter. The display brightness is set to low. Carry out pairing. Check the wireless remote control condition level. If it is low, decrease the distance between the transmitter and the receiver. On the receiver, carry out pairing again with the transmitter that you want to control. Check the conditions for using a USB keyboard with the transmitter. Adjust the brightness of the display. Specifications Transmitting section Oscillator type Crystal-controlled PLL synthesizer Carrier frequencies US models: 470.125 to 607.875MHz 614.125 to 697.875MHz European model: 798 to 862MHz Channel step US models: 125 kHz European model: 25kHz RF power output 1 mW/10 mW/50 mW (e.r.p) selectable Antenna type
/4 flexible wire Occupied RF bandwidth 192 kHz or less Audio delay 1.5 ms Transmission frequency stability level 6.5 ppm Type of emission G1E or G1D Modulation method
/4 Shift QPSK Audio section Maximum input level MIC: 22 dBu (with 0 dB Dimensions (unit: mm (inches)) attenuator) LINE: +24 dBu Audio attenuator adjustment range (pad) 0 to 48 dB (3dB steps, MIC input mode only) Microphone input connector Sony 4-pin (SMC9-4S) (female) Input impedance 4.7 kohms or more Frequency response 20 Hz to 22 kHz T.H.D 0.03% or less Dynamic range 106 dB or more 0 dBu = 0.775 V General Operating voltage 3 V DC, with two LR6 (AA) alkaline batteries Battery life Continuous operating time 3.5 hours (at 25 C (77 F), 10-mW output using Sony LR6 (AA)-
size alkaline batteries with the wireless remote control function off and the display set to AUTO OFF) Operating temperature 0 to 50 C (32 to 122 F) Storage temperature 20 to +60 C (4 to +140 F) Wireless remote control 2.4-GHz 1EEE802.15.4 compliant
* CE6267 model: 169 (6 3/4) 3040U model: 206 (8 1/8) 4250U model: 188 (7 1/2) Mass Approx. 125 g (4 oz) including batteries Supplied accessories Spare battery case (1) Soft case (1) Microphone cable (4-pin to XLR-
type 3-pin) (1) USB adapter cable (1) USB cable (1) Carrying case (1) Scribble sheet (1) Operating Instructions (1) Warranty booklet (1) CD-ROM (1) Optional accessories ECM-77BC/9X lavalier microphones Design and specifications are subject to change without notice.
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2009-07-19 | 470.125 ~ 697.875 | TBT - Licensed Broadcast Transmitter Worn on Body | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2009-07-19
|
||||
1 | Applicant's complete, legal business name |
Sony Corporation
|
||||
1 | FCC Registration Number (FRN) |
0003739166
|
||||
1 | Physical Address |
1-7-1 Konan
|
||||
1 |
Tokyo, N/A 108-0075
|
|||||
1 |
Japan
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
m******@ccsemc.com
|
||||
1 | TCB Scope |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
AK8
|
||||
1 | Equipment Product Code |
DWTB01F
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
R******** T****
|
||||
1 | Title |
Senior Manager
|
||||
1 | Telephone Number |
81-50********
|
||||
1 | Fax Number |
81-50********
|
||||
1 |
c******@jp.sony.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 09/02/2009 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | TBT - Licensed Broadcast Transmitter Worn on Body | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | DIGITAL WIRELESS TRANSMITTER | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | Yes | ||||
1 | Grant Comments | Listed output power is ERP. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except as described in this filing. Co-located operation with module FCCID: AK8RM215 has been evaluated. Endusers must be provided with specific operating instructions for satisfying RF exposure compliance requirements. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Japan Qlty. Assur. Org. Kita-Kansai Testing Center
|
||||
1 | Name |
K******** S********
|
||||
1 | Telephone Number |
81-72********
|
||||
1 | Fax Number |
81-72********
|
||||
1 |
s******@jqa.jp
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 74.861 | M4 | 470.125 | 697.875 | 0.13804 | 0.005 % | 192KG1D | |||||||||||||||||||||||||||||||||
1 | 2 | 74.861 | M4 | 470.125 | 697.875 | 0.02818 | 0.005 % | 192KG1D | |||||||||||||||||||||||||||||||||
1 | 3 | 74.861 | M4 | 470.125 | 697.875 | 0.00331 | 0.005 % | 192KG1D |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC