Wireless Keypad Clavier sans fil Instruction Manual / Mode demploi CECHZK1UC 4-124-373-11(1) US WARNING This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are deemed to comply without testing of specific absorption ratio (SAR). This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. If you have questions about this product, call our technical support line at 1-800-345-7669, or write to:
Sony Computer Entertainment America Consumer Services/Technical Support PO Box 5888, San Mateo, CA 94402-0888 U.S.A Declaration of Conformity SONY CECHZK1UC Trade Name :
Model No. :
Responsible Party : Sony Electronics Inc. Address :
Telephone No. :
This device complies with Part 15 of the FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation of this device. 16530 Via Esprillo, San Diego, CA 92127 U.S.A. 858-942-2230 This Class B digital apparatus complies with Canadian ICES-003. Warning If you come into contact with material from a leaking battery, take the following actions:
If the material gets into the eyes, do not rub. Immediately flush the eyes with clean water and seek medical attention. If the material comes into contact with the skin or clothes, immediately rinse the affected area with clean water. Consult your physician if inflammation or soreness develops. Avoid prolonged use of this product. Take a break at about 30 minute intervals. Stop using this unit immediately if you begin to feel tired or if you experience discomfort or pain in your hands, wrists or arms during use. If the condition persists, discontinue use and consult a doctor. This product is intended for use with the hands only. Do not allow the battery to come into contact with fire or subject it to extreme temperatures such as in direct sunlight, in a vehicle exposed to the sun or near a heat source. Caution Be careful not to pinch your fingers with the clamp when attaching/detaching the wireless keypad to/
from the wireless controller. When disposing of the keypad, carefully follow the precautions listed below:
When removing the battery, do so in a location out of the reach of small children to help prevent accidental swallowing of small parts such as screws. Be careful not to hurt your nails or fingers when removing the battery. Part names Blue button Status indicator Caps lock indicator Touch pad indicator SELECT button*
Orange button POWER switch Directional keys START button*
PS button*
* These buttons can only be used when the keypad is attached to a wireless controller. USB connector Clamp Preparing for use
(System Settings) Checking the version of the PS3 system software To use the wireless keypad, the PS3 system software must be version 2.50 or later. You can check the system software version by selecting
(Settings)
"System Information" on the XMB screen of the PS3 system. Pairing the wireless keypad and the PS3 system Before using the wireless keypad, you must first register or "pair" the keypad and the PS3 system. You only need to do this the first time you use the keypad. 1 Turn on the PS3 system. 2 Slide the power switch of the keypad to "ON". 3 Connect the keypad to the PS3 system using a USB cable. The keypad is now paired with the PS3 system. USB cable Check that the system is turned on (power indicator is lit solid green). Hint A USB cable is not included. Use the USB cable supplied with the PS3 system or any Type A -
Mini-B USB cable to connect or charge the keypad. Turning the wireless keypad on and off Slide the power switch to "ON" to place the wireless keypad in standby mode. When you press any character key, the status indicator will light up to indicate that the keypad is ready to use. To turn off the keypad, slide the power switch to "OFF". Hint If the keypad is not used for a period of time (with the power on), it will switch to standby mode and the status indicator will turn off. Attaching the wireless keypad to a wireless controller When using the wireless keypad with the PS3 system, you must attach it to a wireless controller. Open the clamp.
Place the wireless keypad over the wireless controller as shown in the diagram, and then press down firmly to attach the keypad to the controller. Detaching the wireless keypad Open the clamp, and then carefully pull up on the wireless keypad. Charging the wireless keypad To charge the wireless keypad battery, check that the PS3 system is turned on (power indicator is lit solid green), and then connect the keypad to the system using a USB cable. While charging the battery, the status indicator, the Caps lock indicator and the touch pad indicator will all flash. When charging is complete, these indicators will turn off. Hints The wireless controller is not charged during the process of charging the keypad. The battery has a limited life span. Battery charge duration will gradually decrease with repeated usage and age. Battery life also varies depending on the storage method, usage state, environment and other factors. If the keypad is charged during use, the status indicator will flash. When charging is complete, the status indicator will stop flashing. Entering text You can enter text in the same way as with a standard PC keyboard. To enter an uppercase letter, first press the Shift key. To enter keypad characters that are colored blue or orange, first press the corresponding blue or orange button. To enter an accented letter, first enter the accent and then enter the letter. This character is entered when the blue button is pressed. This character is entered when the orange button is pressed. When the Shift key is pressed, uppercase letters
(instead of lowercase letters) can be entered. Hint To continue to enter keypad characters colored blue or orange, you must press the orange or blue button before each character you enter. Commonly used keys Enters a tab Orange button +
Turns on caps lock Using the wireless keypad with other products You can pair and use the wireless keypad with other Bluetooth-compatible products. For details on pairing with another product, refer to the instructions supplied with the product. To set the keypad to pairing mode, slide the power switch to "ON" while pressing the blue button. Continue pressing the blue button until the keypad is set to pairing mode. When the keypad is in pairing mode, the status indicator, the Caps lock indicator and the touch pad indicator will all flash alternately. If a pass key is requested, enter the numbers specified by the Bluetooth-
compatible product or numbers of your choice (four digits or more) if the product does not specify a pass key. Hints The keypad is not guaranteed to work with all Bluetooth-compatible products and may not work properly with some Bluetooth-compatible products. A USB cable can be used to pair the keypad and the PS3 system only. When the keypad is paired with another Bluetooth-compatible product, the pairing with the original product will be cleared. To use the keypad with the original product, you will need to pair the devices again. When disposing of the wireless keypad When disposing of the wireless keypad, remove the battery and follow local regulations regarding disposing of batteries. Notice Other than when disposing of the keypad, never remove the screws and never remove the battery from the keypad. 1 Using a crosshead screwdriver, remove the screws from the keypad rear (8 places) and carefully remove the casing. 2 Unplug the connector, and then remove the battery. Battery Confirms characters that have been typed but not entered Connector Recycling Lithium-Ion Batteries Lithium-Ion batteries are recyclable. You can help preserve our environment by returning your used rechargeable batteries to the collection and recycling location nearest you. For more information regarding recycling of rechargeable batteries, call toll free 1-800-822-8837, or visit http://www.rbrc.org/
Caution Do not handle damaged or leaking Lithium-Ion batteries. Blue button +
Inserts a line break Moves the cursor left and right Blue button +
Moves the cursor up and down Inserts a space Displays the message box of the PS3 system Switches to touch pad mode Displays the Friends list Using touch pad mode When in touch pad mode, the wireless keypad can be used like a mouse. You can use the touch pad mode for cursor control and clicking in a browser. Move your finger over the area used as a touch pad and tap to enter. When you press the touch pad button, the touch pad indicator will light up and the keypad will switch to touch pad mode. The area that can be used as a touch pad The pointer moves as you move your finger. These keys operate in the same way as the left/right buttons on a mouse. Touch pad button Hint You cannot enter text when the keypad is in touch pad mode. To enter text, press the touch pad button again. FR AVERTISSEMENT Cet quipement est conforme aux limites dexposition aux radiofrquences IC tablies pour un environnement non contrl et se conforme aux exigences de conformit pour lexposition aux RF IC, dans le supplment C OET65 et RSS-102. Cet environnement possde des niveaux denergie RF trs bas se conformant sans tests ncessaires aux taux dabsorption spcifique (SAR). Cet metteur ne doit pas tre utilis conjointement ou plac avec tout autre metteur ou antenne. Remarque Cette unit a t teste et juge conforme aux normes stipules par larticle 15 des rglements de la FCC pour un appareil numrique de catgorie B. Ces normes sont tablies afin doffrir une protection raisonnable contre toute possibilit de brouillage prjudiciable dans une installation rsidentielle. Cette unit produit, utilise et peut mettre une nergie radiolectrique, et si elle nest pas installe et utilise conformment aux instructions, pourrait causer un brouillage prjudiciable la radiocommunication. Il est toutefois impossible de garantir quil ny aura pas de brouillage prjudiciable dans une installation donne. Si cette unit cause un brouillage prjudiciable la rception radio ou tlvisuelle, ce qui peut tre dtermin en activant ou dsactivant lappareil, lutilisateur est encourag tenter de corriger le brouillage en prenant lune ou plusieurs des mesures proposes suivantes :
Rorienter ou dplacer lantenne de rception. loigner lunit du rcepteur. Connecter lappareil une prise sur un autre circuit que celui auquel le rcepteur est connect. Demander de laide au dtaillant ou un technicien radio/tlvision spcialis. Aucun changement ou modification nest permis sans avoir t approuv par les parties responsables des rglementations qui est en droit dinterdire lutilisation de ce produit par lutilisateur. Si vous avez des questions au sujet de ce produit, contactez lassistance technique au 1-800-345-7669 ou crivez :
Sony Computer Entertainment America Consumer Services/Technical Support PO Box 5888, San Mateo, CA 94402-0888 U.S.A. Dclaration de conformit SONY CECHZK1UC Nom commercial :
N de modle :
Partie responsable : Sony Electronics Inc. Adresse :
N de tlphone :
Cet appareil est conforme aux stipulations de larticle 15 des rglements de la FCC et RSS-Gen des rgles IC. Son opration est sous rserve des deux conditions suivantes : (1) cet appareil ne peut pas causer de brouillage prjudiciable et (2) cet appareil doit accepter le brouillage prjudiciable reu, y compris un brouillage qui pourrait causer son fonctionnement irrgulier. 16530 Via Esprillo, San Diego, CA 92127 U.S.A. 858-942-2230 Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Avertissement En cas de contact avec la substance provenant dune fuite au niveau de la batterie, procdez comme suit :
En cas de contact avec les yeux, ne frottez pas. Rincez immdiatement les yeux leau propre et consultez un mdecin. Si la substance entre en contact avec la peau ou des vtements, rincez immdiatement la zone affecte avec de leau propre. Consultez votre mdecin en cas dinflammation ou dendolorissement. vitez lutilisation prolonge de ce produit. Accordez-vous une pause toutes les 30 minutes environ. Arrtez immdiatement dutiliser cet quipement si vous commencez vous sentir fatigu ou si vous prouvez une sensation dsagrable ou une douleur dans les mains, poignets ou bras en cours dutilisation. Si les symptmes persistent, cessez lutilisation et consultez un mdecin. Ce produit est conu pour tre utilis uniquement avec les mains. Ne laissez pas la batterie entrer en contact avec le feu et ne la placez pas un endroit sujet des tempratures extrmes, par exemple sous les rayons directs du soleil, dans une voiture gare en plein soleil ou proximit dune source de chaleur. Attention Veillez ne pas vous pincer les doigts avec lattache lorsque vous attachez le clavier sans fil la manette ou len dtachez. Lors de la mise au rebut du clavier, suivez attentivement les prcautions indiques ci-dessous :
Lorsque vous retirez la batterie, faites-le dans endroit hors de porte des jeunes enfants afin dviter quils avalent accidentellement de petites pices telles que des vis. Veillez ne pas vous casser les ongles ou vous blesser les doigts lorsque vous retirez la batterie. Nom des pices Touche bleu Indicateur de statut Indicateur Verr. majuscule Indicateur pav tactile Touche SELECT
(slection)*
Touche orange Interrupteur POWER
(alimentation) Touches directionnelles Touche START
(mise en marche)*
Touche PS*
* Ces touches ne peuvent tre utilises que lorsque le clavier est attach une manette sans fil. Connecteur USB Attache Prparation lutilisation Vrification de la version du logiciel du systme PS3 Pour utiliser le clavier sans fil, le logiciel du systme PS3 doit tre la version 2.50 ou ultrieure. Vous pouvez vrifier la version du logiciel systme en slectionnant
(Paramtres systme)
"Informations systme" sur lcran XMB du systme PS3.
(Paramtres) Association du clavier sans fil au systme PS3 Avant dutiliser le clavier sans fil, vous devez dabord lenregistrer ou "lassocier" au systme PS3. Vous navez le faire que la premire fois que vous utilisez le clavier. 1 Mettez le systme PS3 sous tension. 2 Poussez linterrupteur dalimentation du clavier sur "ON". 3 Connectez le clavier au systme PS3 laide dun cble USB. Le clavier est maintenant associ au systme PS3. Saisie de texte Vous pouvez saisir du texte de la mme faon que sur un clavier de PC standard. Pour saisir une majuscule, appuyez dabord sur la touche Shift (Maj). Pour saisir des caractres du clavier marqus en bleu ou en orange, appuyez dabord sur la touche bleu ou orange correspondante. Pour saisir un caractre accentu, tapez dabord laccent, puis le caractre. Ce caractre est saisi lorsque la touche bleu est enfonce. Ce caractre est saisi lorsque la touche orange est enfonce. Lorsque la touche Shift (Maj) est enfonce, il est possible de saisir des majuscules (au lieu de minuscules). Conseil Pour une saisie conscutive de plusieurs caractres marqus en bleu ou en orange, vous devez appuyer sur la touche bleu ou orange avant chaque caractre saisir. Touches utilises couramment Mise au rebut du clavier sans fil Lorsque vous mettez le clavier sans fil au rebut, retirez la batterie et respectez la rglementation locale en vigueur applicable la mise au rebut des batteries. Notice Ntez jamais les vis et la batterie du clavier si ce nest lors de sa mise au rebut. 1 laide dun tournevis cruciforme, retirez les vis du dos du clavier
(en 8 endroits) et dtachez dlicatement le botier. 2 Dbranchez le connecteur, puis retirez la batterie. Batterie Insre une tabulation Connecteur Touche orange +
Active le verrouillage des majuscules Confirme les caractres taps mais non encore saisis Cble USB Touche bleu +
Insre un saut de ligne Vrifiez que le systme est sous tension (indicateur dalimentation allum en vert). Touche bleu +
Dplace le curseur vers le haut ou le bas Dplace le curseur vers la gauche ou la droite RECYCLAGE DES ACCUMULATEURS AUX IONS DE LITHIUM Les accumulateurs aux ions de lithium sont recyclables. Vous pouvez contribuer prserver lenvironnement en rapportant les piles uses dans un point de collection et recyclage le plus proche. Pour plus dinformations sur le recyclage des accumulateurs, tlphonez au numro gratuit 1-800-822-8837 (tats-Unis et Canada uniquement), ou visitez http://www.rbrc.org/
Insre un espace Attention Conseil Cble USB non inclus. Utilisez le cble USB fourni avec le systme PS3 ou tout autre cble USB de type A Mini-B pour connecter ou recharger le clavier. Allumer et teindre le clavier sans fil Poussez linterrupteur dalimentation sur "ON" pour placer le clavier sans fil en mode veille. Lorsque vous appuyez sur une touche caractre, lindicateur de statut sallume pour indiquer que le clavier est prt lemploi. Pour teindre le clavier, poussez linterrupteur dalimentation sur "OFF". Conseil Si le clavier reste inutilis pendant un moment (alors quil est allum), il passera en mode veille et lindicateur de statut steindra. Attacher le clavier sans fil une manette sans fil Pour utiliser le clavier sans fil avec un systme PS3, vous devez lattacher une manette sans fil. Dployez lattache.
Placez le clavier sans fil sur la manette sans fil selon lillustration ci-dessus, puis appuyez fermement pour enclencher le clavier sur la manette. Dtacher le clavier sans fil Dployez lattache, puis tirez dlicatement sur le clavier sans fil. Chargement du clavier sans fil Pour charger la batterie du clavier sans fil, vrifiez que le systme PS3 est allum (indicateur dalimentation allum en vert), puis connectez le clavier au systme laide dun cble USB. Pendant le chargement de la batterie, lindicateur de statut, lindicateur de Verr. majuscule et lindicateur pav tactile clignotent tous les trois. Une fois le chargement termin, ces indicateurs steignent. Conseils La manette sans fil nest pas charge pendant la procdure de chargement du clavier. La batterie possde une dure de vie limite. Lautonomie de la batterie diminue au fil du temps, suite son utilisation rpte et son vieillissement. La dure de vie de la batterie varie galement en fonction de la mthode de stockage, des conditions dutilisation, de lenvironnement et dautres facteurs. Si le clavier est recharg en cours dutilisation, lindicateur de statut clignote. Une fois le chargement termin, lindicateur de statut cesse de clignoter. Affiche la bote Messages du systme PS3 Bascule en mode pav tactile Affiche la liste des amis Utilisation du mode tactile En mode pav tactile, le clavier sans fil peut tre utilis comme souris. Vous pouvez utiliser le mode pav tactile pour dplacer le curseur et pour cliquer dans un navigateur. Dplacez le doigt sur la surface utilise comme pav tactile et tapez pour entrer. Lorsque vous appuyez sur la touche pav tactile, lindicateur pav tactile sallume et le clavier passe en mode pav tactile. La surface qui peut tre utilise comme pav tactile Le pointeur se dplace suivant le dplacement de votre doigt. Ces touches fonctionnent de la mme faon que les boutons gauche et droit dune souris. Touche pav tactile Conseil Il est impossible de saisir du texte lorsque le clavier est en mode pav tactile. Pour saisir du texte, appuyez nouveau sur la touche pav tactile. Utilisation du clavier sans fil avec dautres produits Vous pouvez associer et utiliser le clavier sans fil avec dautres produits compatibles Bluetooth. Pour plus de dtails sur lassociation avec un autre produit, consultez les instructions fournies avec le produit. Pour placer le clavier en mode dassociation, poussez linterrupteur dalimentation sur "ON" tout en appuyant sur la touche bleu. Maintenez cette denire appuye jusqu ce que le clavier passe en mode dassociation. Une fois en mode dassociation, les indicateurs de statut, de verrouillage majuscules et de pav tactile du clavier clignotent alternativement. Si une cl didentification est requise, saisissez les chiffres spcifis par le produit compatible Bluetooth ou les chiffres de votre choix (un minimum de quatre chiffres) si le produit ne spcifie pas de cl didentification. Conseils Le fonctionnement du clavier avec tous les produits compatibles Bluetooth nest pas garanti et ce dernier peut ne pas fonctionner correctement avec certains produits compatibles Bluetooth. Lassociation du clavier laide dun cble USB ne peut tre effectue quavec le systme PS3. Lorsquun clavier est associ un autre produit compatible Bluetooth, lassociation avec le produit original est annule. Pour utiliser le clavier avec le produit original, vous devrez associer nouveau ces priphriques. Ne pas utiliser des accumulateurs aux ions de lithium qui sont endommags ou qui fuient.
" and "PLAYSTATION" are registered trademarks of Sony Computer Entertainment Inc.
Also, "PS3" is a trademark of the same company. "XMB" is a trademark of Sony Corporation and Sony Computer Entertainment Inc.
"SONY" and "
"PS3" est galement une marque commerciale de la mme socit. "XMB" est une marque commerciale de Sony Corporation et de Sony Computer Entertainment Inc.
"SONY" et "
" et "PLAYSTATION" sont des marques dposes de Sony Computer Entertainment Inc.
" sont des marques dposes de Sony Corporation.
" are registered trademarks of Sony Corporation. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sony Computer Entertainment Inc. is under license. Les logos et la marque commerciale du mot Bluetooth appartiennent Bluetooth SIG, Inc. et toute utilisation de ces marques commerciales par Sony Computer Entertainment Inc. est accorde sous licence. 2008 Sony Computer Entertainment Inc. All rights reserved. 2008 Sony Computer Entertainment Inc. Tous droits rservs. Printed in China Imprim en Chine