all | frequencies |
|
|
exhibits | applications |
---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Users Manual A | Users Manual | 426.67 KiB | ||||
1 |
|
Users Manual B | Users Manual | 300.22 KiB | ||||
1 | Test Report | |||||||
1 | Test Report | |||||||
1 | Test Report | |||||||
1 | Test Report | |||||||
1 | Cover Letter(s) | |||||||
1 | Test Setup Photos | |||||||
1 | Cover Letter(s) | August 06 2004 | ||||||
1 | Test Report | |||||||
1 | Internal Photos | |||||||
1 | Test Report | |||||||
1 | RF Exposure Info | |||||||
1 | Internal Photos | |||||||
1 | Test Report | |||||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | ID Label/Location Info |
1 | Users Manual A | Users Manual | 426.67 KiB |
4-658-124-11(1) Operating Instructions 5GHz Wireless LAN Access Point PCWA-A500 2002 Sony Corporation Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. If you have questions about this product, call the Sony Customer Information Center at 1-877-760-7669; or write to the Sony Customer Information Center at 12451 Gateway Boulevard, Fort Myers, FL 33913. The number below is for FCC-related matters only. Declaration of Conformity Trade Name: Sony Model No: PCWA-A500 Responsible Party: Sony Electronics Inc. Address: 680 Kinderkamack Road, Oradell, NJ 07649 USA Telephone: 201-930-6972 This phone number is for FCC-related matters only. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. The supplied interface cable must be used with the equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules. WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Owners Record The model and serial numbers are located on the bottom of the product. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. PCWA-A500 Serial No.______________ CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your warranty. FCC ID: AK8PCWAA500 Exposure to Radio Frequency Radiation. The radiated output power of the Wireless LAN Access Point is far below the FCC radio frequency exposure limits. Nevertheless, the Wireless LAN Access Point shall be used in such a manner that the potential for human contact during normal operation is minimized. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:
2 Note The power outlet should be installed near the equipment and should be easily accessible. Safety Information WARNING Opening the unit, for whatever reason, could lead to damages that are not covered by the warranty. Do not touch the device or accessories during thunder storms. Electrical shock could result. This device is made for use in the USA only. For indoor use only. While using the Access Point, do not cover it or turn it on its side. Do not cover the Access Point with objects such as magazines or newspapers or use it in confined, enclosed places, such as the spaces between walls and furniture. Further, do not turn the Access Point on its side while using it. Either situation could cause heat to build up inside the Access Point, leading to overheating and possible fire. Carefully place the Ethernet cable, AC adapter, and other wiring. Personal injury or damage to the Access Point could result from people tripping over the Ethernet cable, AC adapter, or power cord. Protect wiring by locating it in places where people do not walk. Do not swing the AC adapter. Injury could result if the adapter strikes a person or fragile material, such as glass. Keep the Access Point out of the reach of children. Unforeseeable injury could result from swallowing loose parts, etc. Place the Access Point on a stable surface. Do not place the Access Point on wobbly or tilted surfaces. Tipping or falling could result in injury. When using wall mounting, make sure that the wall is strong enough to support the Access Point. The Access Point could fall if the wall is not strong enough, leading to unforeseeable accidents. Further, be careful not to drop the unit or the tools used for mounting it. Doing so could result in unforeseeable accidents. Avoid locations that are directly exposed to sunlight or heaters. Internal overheating could result in fire or damage to the unit. Make sure connectors are properly connected. Do not insert any metallic objects inside the connectors. Short-circuiting the pins could cause fire or damage to the unit. Be careful to insert connectors squarely. Crooked insertion could cause pins to short-
circuit, possibly causing fire or damage to the unit. Use only the supplied AC adapter with your Sony Wireless LAN Access Point. To disconnect your Wireless LAN Access Point from the power supply, unplug the AC adapter. 3 Program 2001, 2002 Sony Corporation Documentation 2002 Sony Corporation Copyright 2000-2001 Atheros Communications, Inc., All Rights Reserved Copyright 1994-2001 The NetBSD Foundation, Inc. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1 Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2 Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3 All advertising materials mentioning features or use of this software must display the following acknowledgement:
This product includes software developed by the NetBSD Foundation, Inc. and its contributors. 4 Neither the name of The NetBSD Foundation nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 4 Copyright 1993-2000 by Darren Reed. The author accepts no responsibility for the use of this software and provides it on an as is basis without express or implied warranty. Redistribution and use in source and binary forms are permitted provided that this notice is preserved and due credit is given to the original author and the contributors. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. Copyright 1980, 1986, 1989 Regents of the University of California. All rights reserved. UNIX System Laboratories, Inc. All or some portions of this file are derived from material licensed to the University of California by American Telephone and Telegraph Co. or Unix System Laboratories, Inc. and are reproduced herein with the permission of UNIX System Laboratories, Inc. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1 Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2 Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3 All advertising materials mentioning features or use of this software must display the following acknowledgement:
This product includes software developed by the University of California, Berkeley and its contributors. 4 Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Copyright 1995, 1996, 1997, 1998, 1999 The Internet Software Consortium - DHCP. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1 Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2 Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3 Neither the name of The Internet Software Consortium - DHCP nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY THE INTERNET SOFTWARE CONSORTIUM AND CONTRIBUTORS AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE INTERNET SOFTWARE CONSORTIUM OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Copyright 1999,2000 by Jef Poskanzer. All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1 Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2 Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 5 Sony, VAIO, and the VAIO logo are trademarks of Sony Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and other countries. Ethernet is a registered trademark of Xerox Corporation. All other trademarks are trademarks of their respective owners. In this manual, Microsoft Windows Millennium Edition is referred to as Windows Me. In this manual, Microsoft Windows 2000 Professional is referred to as Windows 2000. 6 Table of contents Getting started Overview ............................................... 7 What you can do with your Wireless LAN Access Point ..................... 7 System requirements ..................... 8 About the manuals and Help files ... 8 Names of parts and functions ................ 9 About the Access Point initial settings 12 To return the Access Point settings to the factory default settings .. 13 MAC address ............................... 13 Setting and connections Configuring the Access Point settings ............................................ 14 Before configuring the Access Point settings ..................................... 14 Displaying the Access Point setup page .......................................... 16 About the Access Point password .................................. 18 Configuring and changing settings for the Access Point ................. 19 Confirming the firmware version for the Access Point ...................... 20 Confirming the status of the Access Point ......................................... 21 Connecting ........................................... 22 Connecting to a DSL modem, cable modem, or ISDN router ........... 22 Precautions when mounting the Access Point on a wall ................................ 24 Additional information Precautions .......................................... 26 Specifications ...................................... 27 Getting help ......................................... 28 Glossary ............................................... 29 Troubleshooting ................................... 31 G e t t i n g s t a r t e d Overview What you can do with your Wireless LAN Access Point The 5GHz Wireless LAN Access Point PCWA-A500 is designed for constructing a wireless LAN (Local Area Network) environment. Because the wireless LAN does not require cable connections, client computers can operate anywhere within a specified range. Connect your Access Point to a power outlet, insert the 5GHz Wireless LAN PC Card PCWA-C500 (sold separately) into your computer, and use the provided software together with the Access Point to construct a wireless LAN environment on multiple client computers (16 or fewer is recommended). In a wireless LAN environment, you can share files and folders on other client computers and let others share files and folders on your computer. Further, you can connect the Access Point to a DSL modem, cable modem, or ISDN router to access the Internet from a client computer that is equipped with wireless LAN or from a client computer on an Ethernet LAN that is connected to the NETWORK 2 connector. Internet POWER MESSAGE WIRELESS NETWORK 1 NETWORK 2 To the NETWORK 1 connector Internet service provider DSL modem/
cable modem/
ISDN router To the NETWORK 2 connector Hub 7 System requirements In order to configure the Access Point or check Access Point settings, your computer must satisfy the following hardware and software requirements. A computer installed with a 5GHz Wireless LAN PC Card
(Make sure that the driver required to operate the PC card is installed correctly.) Web browser (The following browsers are recommended.) Microsoft Internet Explorer 5 or later Netscape Communicator 4.75 or later Notes Sony cannot assure trouble-free operation for all computers satisfying the specified system requirements. To construct a wireless LAN environment, the 5GHz Wireless LAN PC Card PCWA-C500 (sold separately) is required. Internet access requires the separate purchase of an Internet connection from an Internet Service Provider (ISP). About the manuals and Help files The following manuals and Help files are provided with this product. 5GHz Wireless LAN Access Point PCWA-A500 Quick Start Guide This guide contains simple explanations on how to set up and configure the Access Point. We recommend reading the guide before using this product. 5GHz Wireless LAN Access Point PCWA-A500 Operating Instructions
(this manual) These instructions contain detailed explanations on how to setup and configure the Access Point. Access Point Online Help Online help explains how to set up and use the Access Point. To configure an Access Point, go to the Access Point setup page. For information on how to display the Access Point setup page and online help, see Displaying the Access Point setup page (page 16). 8 Names of parts and functions Front view Side view 1 2 3 POWER MESSAGE WIRELESS NETWORK 1 NETWORK 2 G e t t i n g s t a r t e d 4 5 6 1 Built-in antenna (not externally visible) 2 Indicators POWER Lights green while power is supplied to the Access Point. MESSAGE Lights when unread logs exceed a certain size. The indicator goes out when the log is displayed. WIRELESS Lights green when data can be exchanged on a wireless LAN. Flashes orange while data is being exchanged on a wireless LAN. NETWORK 1 Lights green when an Ethernet cable is connected to the NETWORK 1 connector. Flashes orange while data is being exchanged using the NETWORK 1 connector. NETWORK 2 Lights green when an Ethernet cable is connected to the NETWORK 2 connector. Flashes orange while data is being exchanged using the NETWORK 2 connector. z Hint All indicators except the POWER indicator flash while the Access Point settings are being changed. 3 Stand/wall-mount adapter The stand/wall-mount adapter is retractable and can be used with the arm extended straight down as a stand or with the arm retracted as a wall-
mount adapter. When extending the arm straight down, it must not be fixed in a position other than that shown in the illustration above. To get the best performance from the built-in antenna, position the Access Point so that the front of the unit creates a right angle with the supporting surface. 9 4 NETWORK 1 connector 5 NETWORK 2 connector Use an Ethernet cable to connect the Access Point to a DSL modem, cable modem, or ISDN router. Use an Ethernet cable to connect the Access Point to an Ethernet LAN hub. 6 DC IN 10 V jack Connects to the AC power adapter. Rear view qa NETWORK 1 NETWORK 2 DC IN 10V 7 9 8 NETWORK 1 NETWORK 2 DC IN 10V 0 7 Ferrite core storage recess Insert the ferrite core of the AC adapter cable qd (on page 11) into this recess, then insert the cable into the AC adapter cable securing groove 8 to fix it in place. For details, refer to the Quick Start Guide. 8 AC adapter cable securing groove Insert the ferrite core of the AC adapter cable qd (on page 11) into the ferrite core storage recess 7, then insert the cable into this groove to fix it in place. For details, refer to the Quick Start Guide. 9 Serial number label The serial number (SERIAL NO.) is printed on this label. The numbers printed below NO. are the serial number. 0 Wall-mounting holes When using the stand/wall-mount adapter as a wall-mount adapter, you can mount the Access Point onto the wall by screwing two screws into the holes. (The screws for mounting the Access Point are not provided. Make sure you use a product that is rated to support the weight of the Access Point.) When mounting the Access Point on a wall, see Precautions when mounting the Access Point on a wall (page 24). qa ID label This label is printed with the ID assigned to the Access Point at the time of shipping. (This ID is also referred to as the Network Name
(SSID).) This ID is required when configuring Access Point settings. 10 Top view qs qs Factory default switch qd Ferrite core Use this switch to return the Access Point settings to the factory default settings. For details, see To return the Access Point settings to the factory default settings (page 13). qd G e t t i n g s t a r t e d 11 About the Access Point initial settings The Access Point is configured as follows at shipment. To return the Access Point settings to the factory default settings, see page 13. Note In the table below, indicates that no setting is made at the time of shipment. Common Host Name Administrator Password Guest Password Time Server (NTP Server) DNS Server Operating Mode NETWORK 1 Connection Method Speed DHCP Client ID NETWORK 2 IP Address Netmask DHCP IP Address Pool Size Speed WIRELESS Network Name (SSID) Encryption (WEP) WEP Key Key Length Frequency (Channel) homegate NAT Router Mode Obtain an IP address automatically Auto-Detect 192.168.11.1 255.255.255.0 16 Auto-Detect ID printed on the ID label at the rear of the product Disabled 40 bits (5 characters) 5.180 GHz (Channel 36) 12 To return the Access Point settings to the factory default settings To return the Access Point settings to the factory default settings, hold down the factory default switch for approximately one second while the power of the Access Point is ON. For information on the location of the factory default switch position, see Names of parts and functions on page 9. G e t t i n g s t a r t e d About the indicator display When you press the factory default switch, the MESSAGE indicator flashes orange. If you continue to press this switch, the WIRELESS, NETWORK 1, and NETWORK 2 indicators flash green, and the operation to return the Access Point settings to the factory default settings begins. When the indicators stop flashing, the Access Point settings have been returned to the factory default settings. For setting details, see page 12. Note If you perform this procedure, all previously set data will be lost. MAC address You can check the MAC address for the Access Point NETWORK 1 connector on the Status Display screen. For details, see Confirming the status of the Access Point (page 21). 13 Configuring the Access Point settings To configure the Access Point settings, use a computer that is connected to the Access Point using the 5GHz Wireless LAN PC Card PCWA-C500 or a computer that is connected to the Access Point NETWORK 2 connector using an Ethernet connection. Before configuring the Access Point settings Connecting to the Access Point using a Wireless LAN PC Card Insert the Wireless LAN PC Card into your computer, and install the PC card driver. Install the Wireless Panel software provided with the Wireless LAN PC Card. Configure the wireless connection with the Access Point after you have configured the computer communication settings on the Wireless Panel. z Hint For details, refer to the manuals provided with the Wireless LAN PC Card. Connecting the Access Point to the Internet To connect the Access Point to a DSL modem:
In the DSL modem operating manual supplied by your ISP, check whether your ISP uses the PPPoE connection method or the router-type DSL modem connection method. Depending on the connection method, perform one of the following. For PPPoE connections:
Check the following using the data supplied by your ISP.
(1) Account ID (Also referred to as the User Account or the User ID)
(2) Account ID password
(3) Service Name (Only when specified by your ISP)
(4) Access Concentrator Name (Only when specified by your ISP) 14 Select Connect using DSL from NETWORK 1 Settings in Easy Setup
(page 19) or from NAT Router Mode Settings in NETWORK 1 Settings in Advanced Setup (page 20). For router-type DSL modem connections:
Select Bridge Mode in Advanced Setup (page 20). To connect the Access Point to a cable modem:
In the cable modem operating manuals supplied by your ISP, check whether your ISP uses the DHCP connection method (where the IP address is automatically assigned to your computer) or the fixed IP address method
(where you set the IP address for your computer manually). Depending on the connection method, perform one of the following procedures. For DHCP connections (the IP address is automatically assigned to your computer):
Check the DHCP Client ID in the data supplied by your ISP. (Only when specified by your ISP) Select Obtain an IP address automatically (DHCP) from NETWORK 1 Settings in Easy Setup (page 19) or from NAT Router Mode Settings in NETWORK 1 Settings in Advanced Setup (page 20). S e t t i n g a n d c o n n e c t i o n s For fixed IP address connections (you have to set the IP address for your computer manually):
Check the IP address assigned to your computer which is provided by your ISP. Select Use the following IP address from NETWORK 1 Settings in Easy Setup (page 19) or from NAT Router Mode Settings in NETWORK 1 Settings in Advanced Setup (page 20). When using an ISDN router:
Select Bridge Mode in Advanced Setup (page 20). Note Depending on your ISP, you may not be permitted to connect a router-type access point to a DSL or cable modem. For details, check the contract terms for your ISP. 15 Displaying the Access Point setup page To configure Access Point settings, go to the Access Point setup page. Use one of the following three methods to display the Access Point setup page. Display the Access Point setup page using the Wireless Connection Easy Setup Wizard provided on the Wireless LAN PC Card. (page 17) Note This method can only be used with Windows Me or Windows 2000. Display the Access Point setup page from the Wireless Panel. (page 17) Display the Access Point setup page by entering the IP address in the web browser. (page 18) Note If your web browser is configured to use a web proxy server, set the browser proxy settings so that the browser does not use a proxy server for the Access Point IP address.
(The factory default setting for the Access Point IP address is 192.168.11.1.) z Hints The Access Point setup page for configuring Access Point settings is saved in the Access Point internal memory. To display the Access Point setup page, it is not necessary to connect to the Internet. When using an Ethernet connection to display the Access Point from your computer, see Display the Access Point setup page by entering the IP address in the web browser. (page 18). 16 S e t t i n g a n d c o n n e c t i o n s Note Depending on the firmware version of the Access Point you are using, the displayed screen may differ from that shown above. Display the Access Point setup page using the Wireless Connection Easy Setup Wizard provided on the Wireless LAN PC Card Note This method can only be used with Windows Me or Windows 2000. 1 Connect the Access Point to the AC adapter. z Hint There is no power switch on the Access Point. Refer to the Quick Start Guide
(separate sheet) when connecting the Access Point to the AC adapter. 2 Start the Wireless Connection Easy Setup Wizard. z Hint To Start the Wireless Connection Easy Setup Wizard, install the Wireless Panel and follow the onscreen instructions. However, you can start the Wireless Network Easy Setup Wizard any time you like. For details, refer to the Quick Start Guide. 3 Follow the onscreen instructions to configure the communication settings for your computer. After you have configured the communication settings for your computer, follow the onscreen instructions to display the Access Point setup page. Display the Access Point setup page from the Wireless Panel 1 Connect the Access Point to the AC adapter. z Hint There is no power switch on the Access Point. Refer to the Quick Start Guide
(separate sheet) when connecting the Access Point to the AC adapter. 2 Double-click the Wireless Panel icon (Received Signal Level indicator) on the taskbar. The main screen for the Wireless Panel appears. 3 Click AP Settings. The web browser starts with the Access Point setup page displayed. 17 Display the Access Point setup page by entering the IP address in the web browser. 1 Connect the Access Point to the AC adapter. z Hint There is no power switch on the Access Point. Refer to the Quick Start Guide
(separate sheet) when connecting the Access Point to the AC adapter. 2 Start up your web browser. 3 Type http://192.168.11.1/ in the URL entry field, then press Enter. The Access Point setup page is displayed. z Hints The IP address above is the factory default setting for the Access Point. If the IP address has been changed, contact your network administrator. When using the NAT Router mode, the Access Point IP address is set to the default gateway for that network. When using the Bridge mode, contact your network administrator for the Access Point IP address. About the Access Point password You can set two types of Access Point passwords, administrator password and guest password. Neither of these passwords is set when the Access Point is shipped from the factory. Therefore, all users are able to configure Access Point settings and display the status of the Access Point. If you want to restrict the privileges of users, you can set a password as described on the Easy Setup page or the various mode setting pages of Advanced Setup. Passwords and restrictions on executable functions are as follows. Password types and ability to use executable functions Function Status display Easy Setup Advanced Setup Display Indicator Firmware update Administrator Possible Possible Possible Possible Possible Guest Possible Not possible Not possible Not possible Not possible 18 Administrator password If you set an administrator password, you will be requested to enter a user name and password when you open the Access Point setup page. To open the Access Point setup page, type admin in the dialog boxs User Name text box, then type the password that you set in the Password text box. Guest password If you set a guest password, you will be requested to enter a user name and password when you open the Access Point Status page. Type guest in the User Name text box, then type the password that you set in the Password text box. Notes If no administrator password is set, a guest password cannot be set. If the administrator password is cancelled, the guest password is also cancelled. S e t t i n g a n d c o n n e c t i o n s Configuring and changing settings for the Access Point There are two types of Access Point settings:
I Easy Setup For those who are not familiar with networks, it is recommend that you use Easy Setup. However, if the Access Point is connected to an ISDN router or router-type DSL modem, you must make settings in Advanced Setup. If you configure settings in Easy Setup, the Access Point operates in NAT router mode. When making a PPPoE connection to your ISP using a DSL modem or when using a cable modem, you can normally configure all of the required settings in Easy Setup. Note If you configure settings in Easy Setup after you have already configured settings in Advanced Setup, the Advanced Setup settings are lost, and the settings are switched to those in Easy Setup. 19 I Advanced Setup Here, you can configure advanced settings for the Access Point. Further, you can select an operation mode for the Access Point from the following two types:
(1) NAT Router mode Similar to Easy Setup, the Access Point operates in NAT router mode, but you can configure slightly more advanced settings.
(2) Bridge mode The Access Point operates as a network bridge. Select this mode when using an ISDN router or router-type DSL modem. 1 Follow the steps for Displaying the Access Point setup page
(page 16) to display the Access Point setup page. 2 Click Easy Setup or Advanced Setup. 3 If an administrator password has been set, you are requested to enter a password. Type admin in the User Name text box, and enter the password, then click OK. The Access Point setup page appears. z Hint The administrator password is not set when the Access Point is shipped from the factory. For details, see About the Access Point password (page 18). If the Access Point settings (Network name (SSID) or data encryption) have been changed, you must use the Wireless Panel to change the communication settings on your computer. For details, refer to the Wireless LAN PC Card Operating Instructions or the Wireless Panel Help. Confirming the firmware version for the Access Point You can confirm the Access Point firmware version on the Access Point Status page. For details, see Confirming the status of the Access Point
(page 21). 20 Confirming the status of the Access Point Perform the following steps to confirm the current status of the Access Point. 1 Follow the steps for Displaying the Access Point setup page
(page 16) to open the Access Point setup page. 2 Click Status. 3 If a guest password has been set, you are requested to enter a password. Type guest in the User Name text box, and enter the password, then click OK. The status of the Access Point is displayed. z Hints The guest password is not set when the Access Point is shipped from the factory. For details, see About the Access Point password (page 18). Also, you can display the Access Point Status page using the administrator user name admin and its password. S e t t i n g a n d c o n n e c t i o n s 21 Connecting Connecting to a DSL modem, cable modem, or ISDN router If the Access Point is connected to a DSL modem, cable modem, or ISDN router, computers that are connected to the Access Point can connect to the Internet via the Access Point. Multiple computers can connect to the Internet via the Access Point simultaneously. POWER MESSAGE WIRELESS NETWORK 1 NETWORK 2 WARNING In the following cases, set the Access Point to Bridge mode before connecting to the Access Point. If you mix up the NETWORK 1 and NETWORK 2 connectors when the Access Point is in the NAT Router mode, problems may occur, such as network anomalies or not being able to communicate with the Access Point. When the Access Point is connected to an ISDN router When the Access Point is connected to an existing LAN operating over a DHCP server For details on setting methods, see Configuring the Access Point settings (page 14). 22 1 Connect the Access Points NETWORK 1 connector to a DSL modem, cable modem, or ISDN router using an Ethernet cable as shown in the illustration below. When the Access Point is connected to an Ethernet LAN, connect the NETWORK 2 connector and the hub using an Ethernet cable. Connect the NETWORK 1 connector to a DSL modem, cable modem, or ISDN router. POWER MESSAGE WIRELESS NETWORK 1 NETWORK 2 S e t t i n g a n d c o n n e c t i o n s Connect the NETWORK 2 connector to the hub. Notes Use a category 5 Ethernet cable when connecting to the Access Point. Normally, an Ethernet straight-through cable is used when connecting a communication device to the NETWORK 1 connector, but depending on the device you may need to use an Ethernet cable with crossover wiring. When connecting to the Access Point, use the same type of cable that you would use to connect the communication device to your computer. For details, refer to the operating instructions for the communication device you are using. When connecting the hub to the NETWORK 2 connector, use an Ethernet straight-
through cable. When connecting the computer directly to the Access Point, use an Ethernet crossover cable. z Hints The cable supplied with the Access Point is an Ethernet straight-through cable. For details on how to use the DSL modem, cable modem, or ISDN router, refer to the respective operating instructions. 23 Precautions when mounting the Access Point on a wall When mounting the Access Point on a wall, the screw size and spacing of mounting holes is as follows. Note that no brackets are provided for mounting the Access Point on a wall. Use screws or nails that meet the following requirements. Notes Using two screws or other fasteners, ensure that the Access Point is securely set on the wall. When fastening the Access Point to a wall with screws, retighten them after mounting the Access Point. Select a location that will hold the weight of the Access Point when mounting it on the wall. If the location cannot hold the weight of the Access Point, the Access Point may drop and cause an accident. When mounting the Access Point on walls made of plasterboard or other fragile material, make sure that the material is strong enough to support the units weight and use special screw fasteners or other fixtures that are made for use with that material. If the unit is fastened with ordinary screws, there is a danger that it may fall. When mounting the Access Point on the wall, be careful not to drop the Access Point or the tools used for doing the work. Dropping the unit or tools could result in unforeseeable accidents. Hanging the Access Point from screws set in a wall:
Head diameter: 0.24 to 0.29 inches (6.0 to 7.5 mm) Body diameter: 0.14 to 0.15 inches (3.5 to 4.0 mm) Length: 1.2 inches (30 mm) or more 2.82 inches (71.5 mm) 24 Fastening the Access Point to a wall with screws:
Body diameter: 0.14 to 0.29 inches (3.5 to 7.5 mm) Length: 1.2 inches (30 mm) or more 2.82 inches (71.5 mm) S e t t i n g a n d c o n n e c t i o n s 25 Precautions AC adapter Use ony the supplied AC adapter. Other AC adapters may cause a failure in the Access Point. Safety Operation Exposure to cold-to-hot temperature extremes or very damp environments may cause moisture to condense on internal parts. This may prevent the Access Point from operating properly. If this should happen, unplug the AC adapter from the power outlet and let the Access Point sit for two to three hours or until the moisture evaporates. Do not drop the Access Point. Careful handling will help prevent damage. Cleaning Clean the casing with a soft cloth, lightly moistened with water or a mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as alcohol or benzene. This may damage the finish of the casing. Installation Do not place the Access Point where it will be exposed to the following conditions:
Unstable surfaces. High humidity or poor ventilation. Excessive dust. Direct sunlight or extreme heat. Closed cars. Magnetized locations (near magnets, speakers, or televisions). Locations exposed to frequent vibration. Locations where the transmission of radio waves may be obstructed by metal plates or concrete walls 26 Specifications Power AC 100 to 240 V, 50/60 Hz
(The power cord plug is for use with AC 120 V.) Power consumption Approximately 7 W Maximum external dimensions Approx. 6.3 9.2 1.9 inches
(Approx. 159 233 48 mm) (w/h/d) The stand is 3.6 inches (approx. 91 mm) in depth. Approx. 6.3 8.7 2.2 inches
(Approx. 159 219 55 mm) (w/h/d)
(With the stand folded) Mass Approx. 42.4 oz
(Approx. 1.2 kg )
(Not including the AC adapter.) Maximum communication distance Approximately 330 feet (100 m) in direct line of sight with no obstacles
(The maximum communication distance depends on the environment.) Recommended number of units connected 16 units or less (number of clients) Protocol support TCP/IP Standards IEEE802.11a/IEEE802.11 (wireless connection) IEEE802.3 (wired connection) Radio frequency 5.15 to 5.35 GHz Data transfer speed (logical value) Wireless connection: 54 Mbps max. Wired connection: 100 Mbps max. WEP (data encryption) 64 bits 128 bits Modulation method OFDM (IEEE802.11a compliant) Operating temperature 41F to 95F (5 to 35C) (no condensation) Storage temperature
-4F to 140F (-20 to 60C) (no condensation) Supplied accessories Operating Instructions Quick Start Guide AC adapter Power cord Ethernet cable (straight-through wiring) Warranty card Other printed materials Design and specifications are subject to change without notice. A d d i t i o n a l i n f o r m a t i o n 27 The Sony Customer Information Services Center offers information about your Access Point, Wireless LAN PC Card, and other Sony products that work with your computer. To contact the Sony Customer Information Services Center, call 1-877-760-7669. Open 24 hours/day, 7 days/week. Getting help This section describes how to get help and support from Sony, as well as troubleshooting tips for your Wireless LAN Access Point. About Sonys Support Options Sony provides several support options for your Wireless LAN Access Point. This Operating Instructions explains how to use your Wireless LAN Access Point. Quick Start Guide explains how to install the Wireless LAN Access Point. Access Point Online Help explains how to configure the Access Point. The Sony Wireless LAN Access Point support Web site http://www.sony.com/
wirelesslansupport/ provides the latest information on your Wireless LAN Access Point. The Sony e-mail support service answers your questions by electronic mail. Just send your question in an e-
mail message and a customer service representative will reply. To send a question to Sony e-mail support, fill out the e-mail form at http://www.sony.com/
wirelesslansupport/
The Sony fax-back service provides you with answers to commonly asked questions. You can use this automated service to request a list of available topics then select the topics you want to receive. To contact the Sony fax-back service, call 1-877-760-7669. 28 Glossary Channel number The frequency used for wireless communications. Wireless communications are available only among client computers and Access Points that use the same channel. Client A computer connected to a LAN (Local Area Network). Also may be called a client computer. DHCP (Dynamic Host Configuration Protocol) DHCP lets network administrators centrally manage and automate assignment of client computer IP addresses. DNS (Domain Name System) A system that translates host names into IP addresses. Networks that use the TCP/IP protocol, such as the Internet, use a set of numbers like 192.168.0.1 (IP address) to identify a computer. However, since the IP address is hard to memorize, DNS was developed to allow a name like www.sony.com to identify a computer for convenience. DNS servers manage these translations from host names into IP addresses. LAN (Local Area Network) A network which is accessible only to its members, unlike the Internet which is open to an unlimited number of people. A LAN may be built for different purposes. For example, you can build an office LAN that is accessible only to members of the same department or a home LAN that is accessible only to family members. PPPoE (PPP over Ethernet) PPPoE is a software protocol that uses a DSL modem to access the Internet. With PPPoE, the client does not set a static IP address. Instead, an IP address is assigned dynamically whenever the client accesses the Internet. Protocol The formal specifications that define the procedures for computers to follow when transmitting and receiving data. TCP/IP (Transmission Control Protocol/Internet Protocol) TCP/IP is the network communications protocol that is used to communicate over the Internet. TCP is a connection-oriented protocol for establishing reliable, sequenced data transfer. TCP ensures that data reaches its destination. IP assembles and addresses data packets for transmission to their network destinations. A d d i t i o n a l i n f o r m a t i o n 29 WAN (Wide Area Network) A network that interconnects remote LANs through the Internet or telephone lines. WEP IEEE802.11-compliant security system. Using the WEP key as the password, only client computers and Access Points that have the same ID and password may log on to the same wireless LAN for file sharing. 30 Troubleshooting Problems related to the Access Point:
Read the Troubleshooting section of this guide before calling Sony Customer Information Services. If you still cannot resolve the problems after referring to these sources, call Sony Customer Information Services. Symptom Cause/Remedy The Access Point is not operating properly or does not operate at all. The NETWORK 1 or NETWORK 2 indicator is not lit. None of the indicators except the POWER indicator are lit. c The Access Point is not supplied with power. Connect the Access Point to a power outlet with the supplied AC adapter. c There is an obstacle between the Access Point and the computer containing the Wireless LAN PC Card, or they are too far apart from each other. c Remove the obstacle between them. Or place the Access Point and the computer containing the Wireless LAN PC Card closer together. (The maximum communication distance depends on the environment.) c The cables are not properly connected. Check that you have connected the correct cables. A d d i t i o n a l i n f o r m a t i o n c The indicator display setting is turned OFF. Turn the power off, then turn it back on again. Or follow the steps for displaying the Access Point setup page (page 16), open the Access Point homepage, and change the indicator display using the "Switch" button in Display Status. 31 The Sony e-mail support service answers your questions by electronic mail. Just send your question in an e-mail message and a customer service representative will reply. To send a question to Sony e-mail support, fill out the e-mail form at http://www.sony.com/wirelesslansupport/
The Sony fax-back service provides you with answers to commonly asked questions. You can use this automated service to request a list of available topics and then select the topics you want to receive. To contact the Sony fax-back service, call 1-877-760-7669. The Sony Customer Information Services Center offers information about your Access Point, Wireless LAN PC Card, and other Sony products that work with your computer. To contact the Sony Customer Information Services Center, call 1-877-760-7669. Open 24 hours/day, 7 days/week. Printed in Japan
1 | Users Manual B | Users Manual | 300.22 KiB |
4-660-142-11(1) Applications 5GHz Wireless LAN Access Point PCWA-A500 Quick Start Guide This guide provides an overview of the functions of the 5GHz Wireless LAN Access Point PCWA-A500 and the necessary preparations before use. Please read first. Accessing the Internet from a variety of household locations By using a computer with a Wireless LAN PC Card, you can communicate with the Access Point, and share files with other computers via the Access Point. Furthermore, if you connect the Access Point to a DSL modem, cable modem or ISDN router, you can access the Internet from a variety of household locations. POWER MESSAGE WIRELESS NETWORK 1 NETWORK 2 z Hint This guide describes installation procedures for connecting the Access Point to a DSL modem, cable modem or ISDN router. Please refer to the Operating Instructions for the Ethernet connection procedure. Installation and setup procedure Step 1 Set up the Access Point and connect power. Step 2 (Described in Wireless LAN PC Card Quick Start Guide) Insert the Wireless LAN PC Card into the computer, and install the Wireless LAN PC Card driver. This process is described in the Wireless LAN PC Card Quick Start Guide that comes with your Wireless LAN PC Card. Step 3 (Described in Wireless LAN PC Card Quick Start Guide) Install the Wireless Panel software supplied with the Wireless LAN PC Card. Step 4 (Described in Wireless LAN PC Card Quick Start Guide) Configure the appropriate computer communications settings. z Hint Select Access Point Connection Mode. Step 5 Configure the appropriate communications and Internet connection settings for the Access Point. Step 6 (Described in Wireless LAN PC Card Quick Start Guide) Configure the computer communications settings to match the settings made in Step 5. Step 7 Connect the Access Point to the DSL modem, cable modem or ISDN router. PCWA-A500 Sony Corporation 2001 Printed in Japan This guide for the 5GHz Wireless LAN Access Point PCWA-A500 is intended to be read together with the manuals provided with the 5GHz Wireless LAN PC Card PCWA-C500 (sold separately). Unpacking While unpacking the product, confirm that the following items are present. Access Point AC Adapter POWER MESSAGE WIRELESS NETWORK 1 NETWORK 2 Ethernet Cable (straight-through wiring) Power Cord Operating Instructions Quick Start Guide (this sheet) Warranty Card Other Printed Matter Step 1 Set up the Access Point and connect power Locating The Access Point stand is hinged, so it can be lowered or raised. It serves as a normal stand when lowered or as a wall-mount adapter when raised. Stand lowered
(standing) Stand raised
(for wall-mounting) NETWORK 1 NETWORK 2 DC IN 10V NETWORK 1 NETWORK 2 DC IN 10V Wall-mounting Holes Using in the normal standing position The stand supports the Access Point on a horizontal surface. For optimum performance, use the stand to keep the front face of the Access Point vertical during operation. Installation Notes Install the Access Point on a stable surface. Do not install it on a shelf or other place where jarring or vibration might cause it to fall. Do not install the Access Point in any location where passers-by might accidentally come in contact with the Access Point or its cabling. Using the stand as a wall-mount adapter When mounting the Access Point on a wall, the size and spacing of mounting holes is as follows. Note that no brackets are provided for mounting the Access Point on a wall. Use screws or nails that meet the following requirements. Hanging the Access Point from screws set in a wall:
Fastening the Access Point to a wall with screws:
Body diameter: 0.14 to 0.29 inches (3.5 to 7.5 mm) Length: 1.2 inches or more (30 mm or more) 2.82 inches
(71.5 mm) Notes Using two screws or other fasteners, ensure that the Access Point is securely set on the wall. When fastening the Access Point to a wall with screws, retighten them after mounting the Access Point. Select a location that will hold the weight of the Access Point when mounting it on the wall. If the location cannot hold the weight of the Access Point, the Access Point may drop and cause an accident. When mounting the Access Point on walls made of plasterboard or other fragile material, make sure that the material is strong enough to support the unit's weight and use special screw fasteners or other fixtures that are made for use with that material. If the unit is fastened with ordinary screws, there is a danger that it may fall. When mounting the Access Point on the wall, be careful not to drop the Access Point or the tools used for doing the work. Dropping the unit or tools could result in unforeseeable accidents. Connecting power 1 Connect power to the Access Point as shown below. The following illustrations show the normal standing position. Power Outlet DC IN 10V Head diameter: 0.24 to 0.29 inches (6.0 to 7.5 mm) Body diameter: 0.14 to 0.15 inches (3.5 to 4.0 mm) Length: 1.2 inches or more (30 mm or more) 2.82 inches
(71.5 mm) POWER MESSAGE WIRELESS NETWORK 1 NETWORK 2 AC Adapter 2 Fit the ferrite core (thick cylindrical part) of the AC Adapter cable into the recess on the back of the Access Point, and insert the cable in the cable securing groove. NETWORK 1 NETWORK 2 DC IN 10V z Hint There is no power switch on the Access Point. Continued on next page Getting help This section describes how to get help and support from Sony. About Sonys Support Options Sony provides several support options for your Wireless LAN Access Point. When you have questions about your Wireless LAN Access Point, check these options for answers:
This guide explains how to install the Wireless LAN Access Point. Operating Instructions explains how to use your Wireless LAN Access Point. Access Point Online Help explains how configure your Wireless LAN Access Point. The Sony Wireless LAN PC Card support Web site http://www.sony.com/wirelesslansupport/ provides the latest information on your Wireless LAN PC Card. The Sony e-mail support service answers your questions by electronic mail. Just send your question in an e-mail message and a customer service representative will reply. To send a question to Sony e-mail support, fill out the e-mail form at http://www.sony.com/wirelesslansupport/
The Sony fax-back service provides you with answers to commonly asked questions. You can use this automated service to request a list of available topics and then select the topics you want to receive. To contact the Sony fax-back service, call 1-877-760-7669. The Sony Customer Information Services Center offers information about your Access Point, Wireless LAN PC Card, and other Sony products that work with your computer. To contact the Sony Customer Information Services Center, call 1-877-760-7669. Open 24 hours/day, 7 days/week. Step 2 Insert the Wireless LAN PC Card into the computer, and install the Wireless LAN PC Card driver Refer to the Wireless LAN PC Card Quick Start Guide for details. Display the Access Point setup page Access Point settings are performed on the Access Point setup page. This Setup page can be displayed in three methods. z Hint The Setup page and Access Point settings are stored in memory within the Access Point, so it can be displayed without being connected to the Internet. Step 3 Install the Wireless Panel software supplied with the Wireless LAN PC Card Refer to the Wireless LAN PC Card Quick Start Guide for details. Step 4 Configure the appropriate computer communications settings Refer to the Wireless LAN PC Card Quick Start Guide for details. Step 5 Configure the appropriate communications and Internet connection settings for the Access Point. Settings are configured using a computer with a Wireless LAN PC Card connected without wires the Access Point, or using a computer connected via Ethernet to the NETWORK 2 connector on the Access Point. Before setting up the Access Point Perform the following procedures as needed. When connecting the Access Point to the Internet Confirm the following items first. s If connecting through a DSL modem From the information provided by your ISP (Internet Service Provider) and your DSL modem operating manual, determine whether the connection to your ISP is a PPPoE connection or if your DSL modem supports a router type connection. Then confirm the following according to the connection type determined. For PPPoE connection:
Determine the following items from the information provided by your ISP:
(1) Your account ID (called User Account or User ID)
(2) The password corresponding to your account ID.
(3) Service name (if specifically provided)
(4) Access Concentrator name (if specifically provided) For router type DSL modem connection:
No particular information needs to be determined beforehand. s If connecting through a cable modem From the information provided by your ISP and your cable modem operating manual, determine whether the connection to your ISP is a DHCP connection (computer IP address assigned automatically) or a connection by a fixed IP address (computer IP address entered manually). Then confirm the following according to connection type. For a DHCP connection (computer IP address assigned automatically):
Determine the DHCP Client ID from the information provided by your ISP (if specifically provided). For a fixed IP address (computer IP address entered manually):
Determine the IP address to be assigned to your computer from the information provided by your ISP. s If using an ISDN router No particular information needs to be determined beforehand. Note In some cases, your ISP may not permit connecting the Access Point to a DSL or cable modem as a router. Please obey the terms of your contract with your ISP. Notes If your web browser is configured to use a web proxy server, set the browser proxy settings so the browser does not use a proxy server for the Access Point IP address. (The factory default setting for the Access Point IP address is "192.168.11.1".) The displayed screen may differ from the above, depending on the firmware version of the Access Point. Your web browser version should be Internet Explorer 5 or later, or Netscape Communicator 4.75 or later. Display through a Wireless LAN PC Card using the Wireless Network Easy Setup Wizard Note This method can only be used with Windows Millennium Edition, Windows XP Home Edition, or Windows XP Professional. 1 Start the Wireless Connection Easy Setup Wizard. z Hint To Start the Wireless Connection Easy Setup Wizard, install the Wireless Panel and follow the onscreen instructions. However, you can start the Wireless Network Easy Setup Wizard any time you like. For details, refer to the Wireless LAN PC Card Quick Start Guide. 2 Follow the Wizard to configure the computer communications settings. When finished configring the computer communications settings, continue following the on-screen instructions to display the Access Point setup page. Display from Wireless Panel 1 Run Wireless Panel, and double click the Wireless Panel icon (Received Signal Strength indicator) in the taskbar. The Wireless Panel main screen appears. z Hint Refer to the Wireless LAN PC Card Quick Start Guide for details. 2 Click the AP Setting button. The web browser starts with the Access Point setup page displayed. Display by entering the IP address 1 Start up your web browser. 2 Type http://192.168.11.1/ in the URL entry field, then press Enter. The Access Point setup page appears. z Hint The IP address above is the factory default setting for the Access Point. Contact your network administrator if it has been changed. When the setup page appears, follow the screens to configure the appropriate settings. Please refer to the Operating Instructions (separate booklet) or the online Help if you need further clarification. Access Point settings can be made in the following two ways:
s Easy Setup This method is recommended for those who are unfamiliar with computer networks. However, if the Access Point is connected to a router type DSL modem or to an ISDN router, the Advanced Setup procedure must be used. The Access Point operates as a NAT router Easy Setup can generally be used to make all required settings when the ISP provides a PPPoE connection over DSL modem or when a cable modem is used. Note If Easy Setup is performed after finishing Advanced Setup, the settings made with Advanced Setup are lost, and settings are changed to those made with Easy Setup. s Advanced Setup This method is used to perform detailed settings for the Access Point. Also, Access Point operation can be selected from the following two modes.
(1) NAT Router Mode As with Easy Setup, the Access Point operates as a NAT router, but with more detailed settings available.
(2) Bridge Mode In this mode, the Access Point operates as a network bridge. Select this mode when a router type DSL modem is used. When connecting to the Internet When using a DSL modem with PPPoE connection or a cable modem, either Easy Setup or Advanced Setup can be used. The Easy Setup is described here. When using a router type DSL modem, the Advanced Setup must be used. Setting up PPPoE connection with a DSL modem Select Set address by PPPoE and enter the settings determined previously. Setting up connection with a cable modem 1 Depending on the connection method (IP address setting method) of the ISP, select IP address is set up automatically or IP address is set up manually, and enter the settings determined previously. 2 If you selected IP address is set up manually, enter the IP address determined previously. Setting up connection with a router type DSL modem or an ISDN router Select Bridge Mode under Advanced Setup. Step 6 Configure the computer communications settings to match the settings made in Step 5 Refer to the Wireless LAN PC Card Quick Start Guide for details. Step 7 Connect the Access Point to the DSL modem, cable modem, or ISDN router Connect the DSL modem or cable modem to the Access Point NETWORK 1 connector using Ethernet cable as shown below. Connecting the DSL or cable modem to the NETWORK 1 connector POWER MESSAGE WIRELESS NETWORK 1 NETWORK 2 Notes Use Category 5 Ethernet cable for connections In most cases, Ethernet cable with straight-through wiring is used, but for some communications devices, crossover wiring may be needed. In any case, use the same type of cable as would be used when connecting a computer to the communications device (the supplied Ethernet cable has straight-through wiring). Basic setup for wireless communications is finished.
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2002-01-25 | 5180 ~ 5320 | NII - Unlicensed National Information Infrastructure TX | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2002-01-25
|
||||
1 | Applicant's complete, legal business name |
Sony Corporation
|
||||
1 | FCC Registration Number (FRN) |
0003739166
|
||||
1 | Physical Address |
1-7-1 Konan
|
||||
1 |
Tokyo, N/A 108-0075
|
|||||
1 |
Japan
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
c******@metlabs.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
AK8
|
||||
1 | Equipment Product Code |
PCWAA500
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
R******** T********
|
||||
1 | Title |
Senior Manager
|
||||
1 | Telephone Number |
81-50********
|
||||
1 | Fax Number |
81-50********
|
||||
1 |
c******@jp.sony.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | NII - Unlicensed National Information Infrastructure TX | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Wireless LAN Access Point | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | The listed Output Power is the measured EIRP of this device. The installation and operating configurations of this transmitter, the antenna gain and cable loss, must satisfy MPE Categorical Exclusion Requirements of 2.1091. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Installers and end-users must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Akzo Nobel K.K.
|
||||
1 | Name |
S****** K****
|
||||
1 | Telephone Number |
+81 4********
|
||||
1 | Fax Number |
+81 4********
|
||||
1 |
k******@akzoemc.co.jp
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15E | 20 28 | 5180.00000000 | 5320.00000000 | 0.0394000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC