NANNING FUGUI PRECISION INDUSTRIAL CO.,LTD. NO.51,Tongle Road, Foxconn Industrial Park, District Jiangnan, Nanning, Guangxi China. Tel: 86-771-5086999 Ext: 35081 FAX: 86-771-2168888 Ext: 64886 Approval Sheet Customer Name: Sony Corporation WLAN/BT Module V01 J20H098 Project Name Approval Sheet Rev. Foxconn Part No. SONY Part No. Approved by Reviewed by Prepared by CONTENTS 1 1 REVISION HISTORY .................................................................... 4 2 MANUFACTURING INFORMATION ....................................................... 5 3 PRODUCT OVERVIEW .................................................................. 6 3.1 3.2 APPLICATION SCOPE .................................................................... 6 REGULATION OF EACH COUNTRIES ......................................................... 7 4 MODULE HARDWARE OVERVIEW ....................................................... 8 4.1 4.2 4.3 BLOCK DIAGRAM ....................................................................... 8 FEATURES ............................................................................ 8 INTERFACE AND CONNECTOR ............................................................. 9 5 6 GENERAL SPECIFICATION ............................................................. 10 ELECTRICAL SPECIFICATION .......................................................... 11 6.1 6.2 6.3 6.4 ABSOLUTE MAXIMUM RATING ............................................................ 11 RECOMMENDED OPERATING RATING ...................................................... 11 DC CHARACTERISTICS ................................................................. 11 ESD INFORMATION .................................................................... 11 7 RF SPECIFICATION ................................................... !
IEEE802.11B ...................................................... !
7.1 IEEE802.11G ...................................................... !
7.2 IEEE 802.11N HT20 ................................................ !
7.3 IEEE 802.11A ...................................................... !
7.4 IEEE 802.11AN HT20 ............................................... !
7.5 IEEE 802.11AN HT40 ............................................... !
7.6 IEEE 802.11AC VHT20 .............................................. !
7.7 IEEE 802.11AC VHT40 .............................................. !
7.8 IEEE 802.11AC VHT80 .............................................. !
7.9 BLUETOOTH 4.2 ..................................................... !
7.10 POWER CONSUMPTION ............................................... !
7.11 7.12 POWER ON AND POWER OFF SEQUENCE ................................. !
7.13 USB EYE DIAGRAM .................................................. !
1)USB 2.0 ................................................................ !
THERMAL TEST ..................................................... !
7.14 7.15 ANTENNA ELECTRICAL SPECIFICATION ................................... !
8 MECHANICAL SPECIFICATIONS ....................................... !
8.1 8.2 8.3 SHIELDING COVER DIMENSION ......................................... !
PCBA ASSEMBLY DIMENSION ......................................... !
MOUNT POSITION OF MATERIALS ....................................... !
9 SCHEMATIC ......................................................... !
10 LAYOUT PATTERN ................................................... !
10.1 10.2 PCB LAYOUT ....................................................... !
PCB SILKSCREEN ................................................... !
11 PCB SPECIFICATION ................................................. !
12 OTP CONTENT ....................................................... !
13 LABEL INFORMATION ................................................ !
13.1 MAC ID LABEL ..................................................... !
14 PACKAGE AND STACK INFORMATION ................................. !
2 14.1 CARTON ASSY ..................................................... !
TRAY ............................................................. !
14.2 14.3 PALLET ASSY ...................................................... !
14.4 TRAY ID LABEL ..................................................... !
14.5 CARTON LABEL ..................................................... !
14.6 PALLET LABEL ...................................................... !
15 HANDLING NOTICE ................................................... !
16 RELIABILITY TEST RESULT ........................................... !
3 1 Revision History Date Document revision 2018/04/16 01 Initial release Change Description 4 2 Manufacturing Information Manufacture Country:
Made in China Manufacturer:
NANNING FUGUI PRECISION INDUSTRIAL CO.,LTD. Manufacture Address:
NO.51,Tongle Road, Foxconn Industrial Park, District Jiangnan, Nanning, Guangxi China. 5 3 Product Overview J20H098.00 is based on MTK MT7668BUN, MT7668BUN is highly integrated single chip which features a low power 2x2 11a/b/g/n/ac dual-band WiFi subsystem and a Bluetooth subsystem. The WiFi subsystem contains the 802.11a/b/g/n/ac radio, baseband, and MAC that are designed to meet both the low power and high throughput application. MT7668BUN has a 32-bit RISC MCU that handles WiFi and Bluetooth tasks, and an ARM Cortex-R4 MCU that could offload data frame processing in WiFi host driver. The Bluetooth subsystem contains the Bluetooth radio, baseband, link controller. It also uses the 32-bit RISC MCU for the Bluetooth protocols. 3.1 Application scope The wireless LAN is compliant to IEEE 802.11n, IEEE 802.11 a/b/g and IEEE 802.11 ac standards. Channel Spacing 2.4GHz -> 5MHz, 5GHz-> 20MHz, 40MHz, 80MHz Data rate:
1, 2, 5.5, 11Mbps for 802.11b;
6, 9, 12, 18, 24, 36, 48 and 54Mbps for 802.11a/g;
MCS0(6.5Mbps)~MCS7(72.2Mbps) for 802.11n HT20 mode (single chain) MCS8(13Mbps)~MCS15(144.4Mbps) for 802.11n HT20 mode (dual chains) MCS0(13.5Mbps)~MCS7(150Mbps) for 802.11n HT40 (5G only) mode (single chain) MCS8(27Mbps)~MCS15(300Mbps) for 802.11n HT40 (5G only) mode (dual chains);
MCS0(6.5Mbps)~MCS8(86.7Mbps) for 802.11ac VHT20 mode (single chain) MCS0(13Mbps)~MCS8(173.3Mbps) for 802.11ac VHT20 mode (dual chains) MCS0(13.5Mbps)~MCS9(200Mbps) for 802.11ac VHT40 mode (single chain) MCS0(27Mbps)~MCS9(400Mbps) for 802.11ac VHT40 mode (dual chains) MCS0(29.3Mbps)~MCS9(433.3Mbps) for 802.11ac VHT80 mode (single chain) MCS0(58.5Mbps)~MCS9(866.7Mbps) for 802.11ac VHT80 mode (dual chains) BT:
The BT Module is compliant to Bluetooth 4.2 and EDR standard:
Carrier Frequency: 2402MHz ~ 2480 MHz Carrier Spacing: 1.0MHz for BDR/EDR, 2MHz for LE Duplexing: TDD Modulation: FHSS, GFSK, /4-DQPSK, 8DPSK Symbol Rate:1Mbps (GFSK), 2Mbps (/4-DQPSK), 3Mbps (8DPSK), LE (GFSK) 6 3.2 Regulation of each countries Country Certification Certification No. Remark 7 4 Module Hardware Overview 4.1 Block Diagram The general HW architecture is shown below Figure:
. 4.2 Features IEEE802.11a/b/g/n/ac (2X2) base on MTK MT7668BUN Support BT4.2+LE USB 2.0 Interface, High and Full Speeds supported. Module is powered by the host with a 3.3V +/- 10% supply. Three Metal Antennas on board. 4 layers through Hole PCB design with FR-4 Tg-140 material. 8 4.3 Interface and Connector Pin definition:
Vendor: IRISO Vendor P/N: IMSA-11501S-20Y900 1 20 Pin Number Symbol Name Status Pin definition 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 GND GND RST_L
-
-
Ground Ground Input
"L"-drive reset signal input from Host WOW_L Output Wake on WLAN signal output
"L"-drive is hoped when awake Host Ground Ground DC +3.3V DC +3.3V DC +3.3V DC +3.3V DC +3.3V DC +3.3V DC +3.3V Ground Ground Ground USB_DATA+
USB_DATA-
Ground Ground GND GND VCC VCC VCC VCC VCC VCC VCC GND GND GND DP DM GND GND
-
-
PWR PWR PWR PWR PWR PWR PWR
-
-
-
I/O I/O
-
-
9 5 General Specification Item WiFi Frequency Range BT Frequency Range Maximum Ripple on Supplied Voltage Temperature Operating Temperature Humidity Storage Temperature Operating Humidity Storage Humidity Specification 2412MHz~2462MHz 5180MHz~5240MHz 5260MHz~5320MHz 5500MHz~5700MHz 5745MHz~5825MHz 2402MHz~2480MHz 330mVpp max
-10~60
-40~85 20%~90% (Non-condensing) 20%~90% (Non-condensing) 10 6 Electrical Specification Absolute maximum rating Symbol VDD33 Parameter Maximum rating 3.3V Supply Voltage
-0.3 to 3.63 Unit V Recommended operating rating 6.1 6.2 Symbol VDD33 T AMBIENT Rating 3.3V supply voltage Ambient Temperature Min 2.97
-10 Typ 3.3 Max 3.63 60 Unit V 6.3 DC Characteristics Symbol Parameter Conditions Min Typ. Max Unit V IL V IH V OL V OH R PU R PD Input Low Voltage Input Hight Voltage Output Low Voltage Output Hight Voltage Input Pull-up Resistance Input Pull-Down Resistance Input Voltage VDD33 Input Voltage VDD33 Input Voltage VDD33 IOL=4~16mA Input Voltage VDD33 IOL=4~16mA Input Voltage VDD33 PU=high, PD=low Input Voltage VDD33 PU=low, PD=high
-0.3 VDD33*0.625
-0.3 VDD33-0.4 40 40 75 75 VDD33*0.25 V VDD33+0.3 V 0.4 V VDD33+0.3 V 190 K 190 K 6.4 ESD Information Mode HBM Level
+/-1500 Unit V 11 7. Host integration instructions Install module through golden finger. 12 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
-
-
-
to which the receiver is connected.
-
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that Consult the dealer or an experienced radio/TV technician for help. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules. This device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-
evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID: AK8J20H098. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Industry Canada statement:
This device complies with ISEDs licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le prsent appareil est conforme aux CNR d ISED applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements ISED tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit tre installe de telle sorte qu'une distance de 20 cm est respecte entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-
evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC:
409B-J20H098. Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un dispositif o l'antenne peut tre installe de telle sorte qu'une distance de 20cm peut tre maintenue entre l'antenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC: 409B-J20H098". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
(iii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and
(iv) the worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in Section 6.2.2(3) shall be clearly indicated.
(v) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:
Le guide dutilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment :
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
(ii) le gain maximal d'antenne permis pour les dispositifs utilisant les bandes de 5250 5 350 MHz et de 5470 5725 MHz doit tre conforme la limite de la p.i.r.e;
(iii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5 725 5 850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie pour l'exploitation point point et lexploitation non point point, selon le cas;
(iv) les pires angles dinclinaison ncessaires pour rester conforme lexigence de la p.i.r.e. applicable au masque dlvation, et nonce la section 6.2.2 3), doivent tre clairement indiqus.
(v) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. 1. 2. (
) 3. 4. XXXyyyLPDzzzz-x