SONY X-XXX-XXX-XX(X) rev 0807121pm Data Projector User Manual (Version x.x) Before operating the unit, please read this manual thoroughly and retain it for future references VPL- Series 200x Sony Corporation 389 WARNING To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. WARNING THIS APPARATUS MUST BE EARTHED. WARNING When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power plug to socket-outlet which must be provided near the unit and easily accessible. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power plug. WARNING: THIS WARNING IS APPLICABLE FOR USA ONLY. Uf used in USA, use the UL LISTED power cord specified below. DO NOT USE ANY OTHER POWER CORD. Plug Cap Parallel blade with ground pin
(NEMA 5-15P Configuration) Cord Type SIT, three 16 or 18 AWG wires Length Minimum 1.5 m (4 ft 1 Lin.), Less than 2.5 m (8 ft .3 in.) Rating Minimum 10 A, 125 V Using this unit at a voltage other than 120V may require the use of a different line cord or attachment plug, or both. To reduce the risk of fire or electric shock, refer servicing to qualified service personnel. WARNING: THIS WARNING IS APPLICABLE FOR OTHER COUNTRIES. WARNING 1 Use the approved Power Cord (3-core mains lead) / Appliance Connector / Plug with earthing-contacts that conforms to the safety regulations of each country if applicable, 2 Use the Power Cord (3-core mains lead) /
Appliance Connector / Plug conforming to the proper ratings (Voltage, Ampere). If you have questions on the use of the above Power Cord / Appliance Connector / Plug, please consult a qualified service personnel. IMPORTANT The nameplate is located on the bottom. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. For the customers in the U.S.A This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the PCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consuit the dealer or an experienced radio/
TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules, This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation, If you have any questions about this product, you may call;
Sony Customer Information Service Center 1-800-222-7669 or http://www.sony.com/
Declaration of Conformity Trade Name: SONY Model: VPL-XXXXX Responsible party:
Sony Electronics Inc. Address: 16530 Via Esprillo, San Diego, CA 92127U.S.A. Telephone Number:
858-942-2230 This device complies with part 15 of the FCC Rules, Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
{2) this device must accept any interference received, including interference that may cause undesired operation. For the customers in Canada This Class B digital apparatus complies with Canadian ICES-003. For the customers in Europe The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo, Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents. For the State of California, USA only Perchlorate Material - special handling may apply, See www.dise, ca.gov/hazardouswaste/
perchlorate Perchlorate Material: Lithium battery contains perchlorate. Disposal of the used lamp For the custemers in the USA. Lamp in this product contains mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance
(www.eiae.org). For the customers in U.S.A and Canada In according with 47 CFR Partt5.407
(e) U-NIl devices operating in 5.15~5.25GHz frequency bands are restricted to indoor operations only. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This equipment complies with FOC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated with at least 20cm and more between the radiator and person's body (excluding extremities:
hands, wrists, feet and ankles). WARNING Boe sag Precautions On safety
* Check that the operating voltage of your unit is identical with the voltage of your local power supply. If voltage adaptation is required, consult with qualified Sony personnel, Should any liquid or solid object fall into the cabinet, unplug the unit and have it checked by qualified Sony personnel before operating it further.
* Unplug the unit from the wall outlet if itis not to be used for several days,
* To disconnect the cord, pull it out by the plug. Never pull the cord itself.
+ The wall outlet should be near the unit and easily accessible.
* The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off.
* Do not look into the lens while the lamp is on,
* Do not place your hand or objects near the ventilation holes the air coming out is hot.
+ Be careful not to catch your fingers by the adjuster when you adjust the height of the unit, Do not push hard on the top of the unit with the adjuster out.
* Be sure to grasp both sides of the unit with both hands when carrying the unit. On iRumination
* To obtain the best picture, the front of the screen should not be exposed to direct lighting or sunlight.
* Ceiling-mounted spot lighting is recommended. Use a cover over fluorescent lamps to avoid lowering the
* contrast ratio.
* Cover any windows that face the screen with opaque draperies.
* It is desirable to install the unit in a room where floor and walls are not of light-
reflecting material. If the floor and walis are of reflecting material, it is recommended that the carpet and wall paper be changed to a dark color. Precautions On preventing internal heat buiid-
up The unit is equipped with ventilation holes
(intake) at the bottom and ventilation holes
(exhaust) at the side, Do not black or place anything near these holes, or internal heat build-up may occur, causing picture degradation or damage to the unit. On cleaning Before cleaning Be sure to disconnect the AC power cord from the AC outlet. On cleaning the air filter
* Clean the air filter whenever you replace the lamp. Refer to the Cleaning the Air Filter on the Operating Instructions or Quick Reference Manual for the air filter cleaning. On cleaning the lens The lens surface is especially treated to reduce reflection of light, As incorrect maintenance may impair the performance of the projector, take care with respect to the following:
* Avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or thinner.
* Wipe the lens gently with a soft cloth such as a cleaning cloth or glass cleaning cloth. Stubborn stains may be removed with a soft cloth such as a cleaning cloth or glass cleaning cloth lightly dampened with water,
* Neveruse solvent such as alcohol, benzene or thinner, or acid, alkaline or abrasive detergent, or chemical cleaning cloth, as they will damage the lens surface. On cleaning the cabinet
* Clean the cabinet gently with a soft dry cloth, Stubborn stains may be removed with a cloth lightly dampened with mild detergent solution, followed by wiping with a soft dry cloth.
* Use of alcohol, benzene, thinner or insecticide may damage the finish of the cabinet or remove the indications on the cabinet. Do not use-these chemicals. Tf you rub on-the cabinet with. a stained cloth, the cabinet may be scratched, Ifthe.cabinet is in contact-with a mbber or vinyl resin product for a long period of time, the finish of the cabinet may deteriorate or the coating may. coine off, On LCD projector The: LCD projector'is manufactured using high-precision technology. You may, however, see tiny black poiits and/or bright points (rd, bhie, or green) that continuously appear on the LCD projector:
This:is a normal:result of the tanufacturing process and does not indicate a malfunction. Notes on Installation and Usage Do not install the unit in the following Situations. These installations may cause malfunction ox damage .to the unit, Poorly ventilated:
@ Allow adequate air circulatiotito prevent internal hatbuild-ip. Do not place the unit on: surfaces (mags, blankets, etc, or near materials: (curtains, draperies).that may block the ventilation holes, When the internal heat builds op due'to the block-up, the temperatute serisor.-will function with the message High temp.!
Lamp off in 1 min. The power will be turned off automatically after one-minute. Leave space of more than 30cm (11. %/s inches) around the unit.
* Be cateful that the ventilation holes may inhale tininess such as 2 piece:of paper, Highly heated and humid Avoid installing the unit in a location where the temperature or huniidity is very high, or temperature is very low. To-avoid moisture condensation, do not iistall the unit in a location where the temperature may rise rapidly. Notes on installation and Usage: 5 Subject to direct cool or warm air from an:alt-conditioner When using the unit at an altitude of 1,500.m or higher, set the High Altitude Mode to:
On? in the Installation menu, Failing te.set this mode when using the unitat high altitudes'could bave.adverse effects, stich as Installing in such:a location may cause reducing the reliability of certain malfunction of the unit due to moisture: components:
condensation or rise in tem re;
neation ornisen femperature. Note on:the:screen Near a heat or smoke sensor . Wheniising'a screen. with an uneven surface, stripes patent may rarely appear onthe seren depending on the distatice betwee the: screen and the unit-or the zooming:
magnifications: This is not'a malfunction of the unit. * :
Malfonction of the sensor tay be caused, Very dusty, extremely smoky Avoid installing the unitin avery disty oF extremely_smoky environment. Otherwise), the air filter will become obstructed: and this mmay cause a malfunction. of the unit damage it: Dust preventing the:
through the filter may. cause a ris in the intemal temperature of the unit, Clean the air filter whenever you replace the-lamp,
#6 |. Nots.on Installation and Usage, Do not.use the unit under the following conditions. Do not topple the unit Ae Avoid using as the-unit topples:over on its side. It may cause malfunction, Do not tilt tight/teft Avoid -usinig.as.the unit tilts. more than 20 degregs. Do not install the unit other than on the flooror ceiling, These installations may cause malfunction. Do. not block the ventilation holes Avoid using something 0 cover over the ventilation holes (exhaust/intake);
otherwise, theinternal heat may. build up. Do not place'a blocking object just in front of the lens Do not place any object just in front of the lens that may block the light during projection, Heat from the light may damage the object. Use the: PIC MUTING key to cut off the. picture, Do not use the Security bar for transporting or installation
Use the Security bar atthe side of the projector for.a purpose-of preventing, theft, by attaching a-commercially available theft prevention cable for example. If you lift the projector by holding the Security bar, or hang the projector by using. this bar, itmay cause the projector to:fall or be damaged. Notes on Installation and Usage 70 WLAN Module Specifications Parameter Descriptions Communication Standard |Based on IEEE802.11b/g [Based on IEEE802.11a CSMA/CA 2400 2483.5MHz 2412, 2417, 2422, 2427, 5150 ~ 5250MHz Frequency Band and 2432, 2437, 2442, 2447, 5180, 5200, 5220, Operating Channels 2452, 2457,2462MHz 5240MHz 11 channels 4 channels Channel Space SMHz 20MHz Occupied Band Width 18MHz 18MHz
{Mbps (DSSS-BPSK) 6/9Mbps (OFDM-BPSK) 2Mbps (DSSS-QPSK) 12/18Mbps (OFDM-
5.5/1 1Mbps(CCK) QPSK) Data Rates Supported [|6/9Mbps (OFDM-BPSK) 24/36Mbps (OFDM 12/18Mbps (OFDM-GPSK) |16QAM) 24/36Mbps (OFDM-16QAM)|48/54Mbps (OFDM-
@Connect the AC power cord to a wall outlet
@Press the tC) (on/standby) key.
@Press the INPUT button on the remote commander and select network channel.
@Turn on the power of the computer.
@Make PC wireless enable. 4 WIRELESS Setting up PC Network
@Setting the network on the PC. Select Network Connections from the PC Control Panel, and right-click Wireless Network Connection to display the Wireless Network Connection Properties. Connect using:
LBD Broadcom NetMreme Six Gigabit Controfer smn Eiihent Obtain GNagervet address automaticaly
( Use the folloiding DNS server. addresses: ~
Input the proper values in the IP address and Subnet mask text boxes for the General tab. After setting, click OK.
@Setting up the wireless network on the PC. Click Wireless Network tab, and select Add. Netwoik name [SSID}:
\sltelosomelivork key-~
elwork Authentication:
Data enciyption:
Nota The Wireless network properties appears. Input a network name, and check This is a computer-to-computer [ad hoc]
network; wirless access points are not used After setting, select OK. Connect the projector to the network.
@ Open the setting window Press the MENU key on the remote commander. Select Installation Setting, then select Network Settings. The confirmation dialog appears. Press OK to open the network setting window.
@Setting up the network Select Wireless Network Settings, and select Internet Protocol. TSS:
Home > Wireless Network Settings
| IP address settings fi IP address DNS server t DNS server 2 Input the proper values in IP address and Subnet mask of IP address settings in oder to communicate with the PC.
@Setting up the wireless network Select Wireless Network Settings, and select Ad hoc in Network Mode. InputC(Network)|
Home > Wireless Network Settings Network Mode [Ad hoc. Channel [
Network Name Data Encryption Key Input the same SSID with the one of the PC in Network Name (SSID).