submitted | available | document details (if available) | source link |
---|---|---|---|
July 11 2019 | July 11 2019 |
various | User Manual | Users Manual | 540.07 KiB | July 11 2019 |
Features Supports Bluetooth 5.0 dual-mode (BDR/EDR/ BLE) specifications Support Profile HSP1.2, SPP1.2, A2DP1.3, AVRCP1.6, HFP1.7, DID1.3 ARM Cortex-M4 with Floating Point Unit (FPU) application processor Maximum speed: 156MHz Cadence HiFi Mini Audio Engine DSP coprocessor Maximum speed: 312MHz Andes N903 processor : Maximum speed: 104MHz System in Package (SiP) 32Mb low-power flash memory with 0.2A deep-down current (typical condition) 256kB system RAM (SYSRAM) with low latency USB 2.0 device Support maximum three I2C Master mode 400kbps Up to 3.4Mbps Support maximum three UART interface Up to 3Mbps Support maximum three SPI master interface, Clock up to 52MHz EMMC/SDIO v2.0, up to 48MHz, 1-bit/4-bit mode eMMC4.41 , Stand-alone module with on-board PWB antenna and Bluetooth stack Supports high resolution up to 24-bit, 192 kHz audio data format Supports maximum four I2S interface Supports to connect max three hosts with HFP/A2DP profiles simultaneously Supports smart phone applications by Bluetooth SPP or BLE link Supports firmware field upgrade by USB/OTA Supports two microphones Compact surface mount module:29.5 * 18.0 * 4.0 mm LGA package 152pin, Flatness is less than 0.05mm RoHS compliant Ideal for portable battery operated devices Internal battery regulator circuitry DSP Audio Processing Support for single SCO or Esco link with CVSD/mSBC coding. Peripherals Built-in lithium-ion and lithium-polymer battery charger (up to 1A) Integrated 1.8V and 3V configurable switching regulator and low-dropout (LDO) regulator Built-in ADC for battery monitoring and voltage sense Built-in ADC for charger thermal protection Built-in under voltage protection (UVP) An AUX-In port for external audio input Multiple I/O pins for control and status HCI Interface High-speed HCI-UART interface (supports up to 3M bps) BMS001 User Manual BMS001 BT5.0 Stereo Audio Module Qualifie d MT2811B/A
(This Photos are for reference only) RF/Analog Frequency spectrum: 2.402 GHz to 2.480 GHz Receive sensitivity: -93 dBm (2 Mbps EDR) Crystal : 26MHZ 10PPM@250.3 Max avg power5dBm2db (EDR) , 2dBm2dbLE 1dBm2db (2LE) Audio Codec SBC,AAC, LDAC 24-bit digital-to-analog converter (DAC) with 105dB SNR 12-bit analog-to-digital converter (ADC) with 95dB SNR Supports up to 24-bit, 192 kHz I2S digital audio MAC/Baseband Processor Supports Bluetooth 5.0 dual-mode (FW dependent) BDR/EDR transport for audio, voice, and SPP data exchange BLE transport for proprietary transparent service and Apple Notification Center Service (ANCS) data exchange Operating Condition Operating voltage: 3.2V to 4.6V Operating temperature: -20C to +70C Description The BMS001 Stereo Audio module is made in China, a fully qualified Bluetooth 5.0 dual-mode (BDR/EDR/BLE) module for designers to add wireless audio and voice applications to their products. The BMS001 products is a Bluetooth module that provides a complete wireless solution with Bluetooth stack, integrated PWB antenna, and worldwide radio certifications in a compact surface-mount package. Applications Soundbar and Subwoofer (FW dependent) Bluetooth portable speaker phone Multi-speaker (FW dependent) Bluetooth headset www.sunitec-cn.com BMS001 User Manual FCC Statement List of applicable FCC rules This device complies with FCC part 15C : 15.247. Specific operational use conditions This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. And the module should be installed at a minimum distance of 5 mm away from person nearby. The host product manufacturer should state this information to the host instruction manual. Limited module proceduresApplicable. ( See the "Features", "Applications" of the catalog) Manufacturer reviews detailed test data or host designs prior to giving the host manufacturer approval. The module is installed in the host, and the host needs to be tested according to relevant regulations. For additional hosts other than the specific host originally granted with a limited module, a C2PC application is required on the module grant to register the additional host as a specific host also approved with the module. Trace antenna designsNot applicable. FCC Radiation Exposure Statement This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 5 mm between the radiator and user body. Antenna Information Antenna Type: PCB Antenna Antenna Gain: 2.84 dBi The antenna is permanently attached and not consideration of replacement. Label and compliance information This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: 2AMX3BMS001 Or Contains FCC ID: 2AMX3BMS001. Information on test modes and additional testing requirements Any final host product with the modular transmitter installed should be under test according to guidance given in KDB 996369 D04. To enter test mode for module, WCN_combo_tool software and command is necessary. When something wrong happens in configuring test modes for host product with module, host product manufacturer should coordinate with module manufacturer for technical support. It is recommended that some investigative measurements should be taken to confirm that host product with module installed does not exceed the spurious emissions limits or band edge limits. Part 15 Subpart B disclaimer The modular transmitter is only FCC authorized for the specific rule parts (FCC Part 15.247) list on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed when contains digital circuity. www.sunitec-cn.com BMS001 User Manual Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. L'metteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR d'Innovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
1)L'appareil ne doit pas produire de brouillage;
2)L'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains IC: 23011-
BMS001 any similar wording that expresses the same meaning may be used. l'appareil hte doit porter une tiquette donnant le numro de certification du module d'Industrie Canada, prcd des mots Contient un module d'mission , du mot IC: 23011-BMS001 ou d'une formulation similaire exprimant le mme sens, comme suit The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'valuation dans la section 2.5 de RSS 102 etla conformit l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne surl'exposition et la conformit de rf. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 10 mm between the radiator and your body. Cet metteur ne doit pas tre Co-plac ou ne fonctionnant en mme temps qu'aucune autre antenne oumetteur. Cet quipement devrait tre install et actionn avecune distance minimum de 10 mm entre le radiateur et votre corps. CE Statement Body-worn SAR testing has been carried out at a separation distance of 5 mm. To meet RF exposure guidelines during body-worn operation, the device should be positioned at least this distance away from the body. Manufacturer: Sunitec Enterprise Co., Ltd Address of Manufacturer:No. 192, Runtang Ind,Danhu community, Fucheng, Longhua District, Shenzhen, China (ZIP:518100) Country of origin Made in China. All products bearing this symbol are waste electrical and electronic equipment which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points. www.sunitec-cn.com
This product uses the FCC Data API but is not endorsed or certified by the FCC