FCC ID: 2AX5A-BMFC01 Hard floor cleaner

Hard floor cleaner BMFC01 Manual Instruction Model No.: BMHC01 Instruction Manual Contents:

Safety Instruction Product introduction Installation Daily maintain & installation Common faults Specification Safety instruction About the manual Please follow the manual instruction to install the machines and keep this manual instruction. If you transfer the product to any third party to use, please attach this manual instruction. Any discrepant operation might lead to the damage of the product or possible personal hurt. We would be free of any charge if there is any loss due to operate not according to the manual instruction. Product Safety Instruction When you clean or maintain the machine, do take the plug out. The product is assumed to be used at home, not for commercial or industrial use. The product is assumed to be used on hard floor, including rubber floor, marble floor, granite floor, terrazzo floor, solid wood floor, composite floor, bamboo floor, and all kinds of mirror surface tile, Porcelain tile etc which has a flat surface. This product effect might not be so good on the none-flat surface. This product is not suitable to those who is capable on physical, Psychological (including kids). Don't touch this electrical part with wet hands in case of any risk Don't use this machine near to the heater, or stove which are too hot in case of machine plastic deformation. Don't wet the machine body in case of any risk of water inlet and then leads to fire, or electric shock etc. When using this machine, if there is situation like too much heat, or strange noise, or bad smell come out, please stop to use this machine When the plug is damaged, please don't use the machine and ask for the after sale service for further help. Please use our original adaptor for the charging and don't use other brand adaptor which might lead to some damage to the circuit and immediately. cause fire risk. If you don't use this machine for a long time, please turn off this machine and take off the plug. When you finish using the machine, make sure clean the dirty water tank in case of any risk of dirty block. There are electrical parts on the body and lower brush, please don't immerse whole machine into water. Please don't try to disassemble the machines and try to use this machine for other purpose, which might cause the damage of the machine. Please use the correct voltage range to use this machine, the voltage range is indicated in the rating label. When cleaning the stairs, please make sure you hold the machine well in case of any falling down. After using the machine, please put the machine on the body. Please equip the water tank(clean water and dirty water) well before using. Product parts introduction:

The install of the machine:

How to use this machine:

Preparation when you start to use the machine, includes:

Please make sure that the machines install well and check whether the battery power is enough. Please make sure that there is clean water in the clean water tank. Start to use:

Switch on the machine after adding the clean water into the "clean water" tank, press the switch buttons for 1~2s to let the machine work, which shall wet the rollers. Hold the handle and move the machine on the hard floor and do the mopping. Press the switch again to turn off the machine. When the machine finish working, please clean the dirty water tank and clean water tank, and add 100ml~150ml water in the base and then put the machine on the base to work another 3minutes to do the self cleaning of the rollers. Take off the rollers and dry them on the base. Start to use:

Insert the adaptor to the machine, and connect with the power. Power indicator:

Power indicator lighting, indicates: 100%, 65%,30% of the power. Three lights power range <100%, >65%. Two lights power range: >30%, <65%. One light power range: <30%. Three lights twinkle: nearly no power and need to charge immediately. Charge:

Daily maintains and installs:

Daily maintains and installs:

Daily maintains and installs:

Common faults:

Common faults:

Possible reason Solution Product does not work:

2. Dirty water tank is fulfilled. Take out the water tank and clean it. 1. No power or shorted powered Please charge the machine 3. Roller is blocked by the air things Clean the roller 4. If none is as above 1. Water tank is installed in the wrong position Please contact us. Install the water tank again 2. Roller is blocked by hair things. Clean the roller Product is weak in cleaning or water leakage 3. Lower battery Please charge the machine Machine shakes terribly:

Product could not be charged:

4. If none is as above 1. Roller is not installed well. 2.If none is above. 1. The adaptor is not collected well. 2.If none is above. Please contact us. Install the roller again. Please contact us. Please check the adaptor connect well. Please contact us. 1. No clean water in the clean water tank Add clean water Clean water does not come out:

2. the water tank is not installed well. Re-install the water tank 3. If none is above Please contact us. Product Spec:

Product Rated voltage:

Rated currence:

Battery capacity:

Clean water tank:

Dirty water tank:

Charging time:

Product size:

Net weight:

Data DC 11.1V 3.2A 2200mAh 400ml 250ml 2-3h 304*250*1220mm 2.5kg Working time after fully charging:

30min Special Safety Instructions 1. Do not use the hard floor cleaner in the immediate proximity to sources of heat and do not mop hot objects such as cigarette butts or ashes. 2. Always connect the power plug into the socket with dry hands. 3. Before you start using the machine, first remove large or sharp object from the floor in order to avoid possible damages. 4. When disconnecting the power plug, do not pull the cord, firmly grasp the plug. Cleaning and Maintenance Parts of the device must not be cleaned in the dishwasher except the roller. To clean the casing, switch the device off and disconnect the adaptor from the socket. If necessary, you can clean the casing, filter compartments of the hard floor cleaner, and the roller. Do not use abrasive cleaning agents (scouring agents, diluting agents) because they can damage the synthetic surface of the device. FCCCaution Thisd evice complies withp art 15 oft heFCC Rules. Operationiss ubject tothe following twoco nditions: (1) Thisd evice may not cause harmfulin terference, and (2) thisd evice must accept any interferencer eceived, includingin terference thatm ay cause undesiredo peration. Any Changes orm odifications not expressly approvedb yth e party responsiblefor compliance couldv oid theu ser's authorityto operatet hee quipment. Note: Thiseq uipment has beentes tedan dfo undto comply witht helim its foraClass B digital device,p ursuantto part1 5o f theFCC Rules. These limits are designedto provide reasonable protection against harmfulin terference inares idential installation. Thise quipmentg enerates uses and canrad iate radio frequencyen ergy and,if not installedan du sedin accordancewit hth ei nstructions, may cause harmful interference torad ioco mmunications.Ho wever, thereis no guarantee thatin terferencewillnot occur inap articularin stallation.If thise quipmentdoes cause harmfulin terferenceto radio ort elevision reception,w hich canbed eterminedb ytu rningth e equipmento ff and on,t heuserisencourag edto tryto correctthe interference by oneorm oreo f the followingm easures:

-Reorient orr elocate therec eivingan tenna.

-Increase thes eparationb etweenth eequip ment and receiver.

-Connect thee quipmentinto ano utleto nac ircuitd ifferent fromth at towh ichthe receiverisc onnected.

-Consultth e dealer oran experiencedrad io/TV technician forh elp. This equipmentcom plieswithFCC uncontrolledenviro nment. radiation exposure limits setfor thfo ran

C5266091_X10_Ed.2 SUZHOU BENM KITCHEN CO., LTD Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date:

Nov.04.2020 Subject: Request for Confidentiality FCC ID: 2AX5A-BMFC01 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality Short-Term Confidentiality NOTE 2 No No No No No No No NOTE 1 NOTE 1 No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In case of short-term Confidentiality, the applicant requests the exhibits selected above are withheld from public view for a period of ____45__ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. 1/1 C5266091_X10_Ed.2 Sincerely, Signature:

Name: Merry Ma Title: Manager 1/1

C5266091_X8_Ed.1 Letter of Authorization SUZHOU BENM KITCHEN CO., LTD Company: SUZHOU BENM KITCHEN CO., LTD Address: NO.555 HEAN RD. PUZHUANG TOWN WUZHONG DISTRICT, SUZHOU, CHINA Product Name: Hard floor cleaner Model Number: BMFC01 FCC Identifier: 2AX5A-BMFC01 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Merry Ma Title: Manager Date: Nov.04.2020 Signature of applicant:

1/1