FCC ID: 2AAQQHR9 Heart Rate Sensor Original Equipment

Blue pulse® HEART RATE TRANSMITTER– User Manual

 2. Connect one side of Fabric Strap to the elastic strap.  Then wear it over

your chest and meet the strap with the Transmitter at the other side.

Thank you for purchasing LifeVisa products.  This manual contains information required to

use the Heart Rate Transmitter. Please read this manual in detail before use.

TRANSMITTER BATTERY INSTALLMENT

This Transmitter includes a 3V CR2032 lithium battery.  

 Please follow below steps to install the battery.

 Step 1. 

 Insert the battery (CR2032) with the positive (+) side up.

 ☆ Make sure the battery is hooked by the contact spring.

 Step 2.

 Put on the O‐Ring in the groove to 

 ensure water resistance.

 ☆ Make sure to place the O‐Ring

     properly in order to prevent battery 

     composition from being spoiled by 

     sweat and moisture.

 Step 3. 

 Place Battery Cover .

 Step 4.

 Tighten Battery Cover .

3. Adjust the strap length to fit around  your chest snugly and comfortably,  just below the pectoral

muscles.

HOW TO WEAR THE TRANSMITTER

The heart rate band consists of two conductive electrodes, which are used as the main

components to sense the heartbeat.

4. Check that the wet electrode areas are firmly against your skin and that

the logo of the Transmitter is in a central, upright position Lifevisa letter L toward to the right

hand side.

Now you can start training.

ELECTRODES

For best performance, wet the electrodes with water or ECG gel before installing the belt. This makes it

easier for both electrodes to pick up the heartbeat ECG signal.

1. Attach the heart rate sensor to the two spring clasps on the webbing, with the font Lifevisa facing up.

 NOTE:

 ☆ Dry electrode areas contact with skin will cause heart rate signals

     detection unstable or erroneous "0" reading, especially at the

     beginning of exercising or cold dry winter months.

Applicability to Smart Phone, Heart Rate Monitor and Sports Equipment

1

2

System Pairing

Select the appropriate APP and pair it

with the heart rate sensor

After putting on the chest strap, the mobile phone or the settings to be connected,

such as: a treadmill with a Bluetooth heartbeat receiver, must complete the connection

with the chest strap within one minute, otherwise the electronic device on the chest

strap will automatically enter sleep status.

In this case, the user only needs to unplug the heart rate sensor from the chest strap,

and then re-attach the heart rate sensor to the chest strap to restart the connection

function.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one of the following measures:

. Reorient or relocate the receiving antenna.

. Increase the separation between the equipment and receiver.

. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

. Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority to operate this equipment. (Example - use

only shielded interface cables when connecting to computer or peripheral devices).

Lifevisa Bluetooth converter application

 The heart rate transmitter chest strap is a high tech product, so that careful maintenance is

Troubleshooting & Maintenance

necessary.

 ● After use, please wash the electrode area of the heart rate transmitter with water

and use clean cloth to wipe it.

FCC Radiation Exposure Statement

 ● The heart rate transmitter has to be stored under dry condition, and kept away

from an environment at extreme temperature.

 ● Please place the heart rate transmitter horizontally if not use. Pulling or bending

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with a minimum distance of 0.5 centimeters between

the radiator and your body.

is inhibited to prevent the electrode area from damage.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

 ● Do not place the heart rate transmitter on a metal surface or in proximity

to magnetic area (including magnet).

 ● The electrode area and ECG paste shall not be used on injured skin.

 ● The skin shall be kept clean before and after using the heart rate transmission

chest strap.

The antennas used for this transmitter must be installed to provide a separation distance of at least 0.5 cm

from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference

received, including interference that may cause undesired operation.

3

4

7 Ree,

TAIWAN BIOTRONIC TECHNOLOGY INC. No.59-3, Sec. 2, Fuxing Rd., Wufeng Dist., Taichung City, 413 Taiwan Federal Communications Commission Authorization and Evaluation Division , ;

Equipment Authorization Branch ee 7435 Oakland Mills Road =

Columbia, MD 21046 Date: 2021-08-23 To whom it may concern:

We, the undersigned, hereby authorize Worldwide Testing Services (Taiwan) Co., Ltd to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2AAQQHRS including the signing of all documents related to these matters. Any and all acts carried out by Worldwide Testing Services (Taiwan) Co., Ltd on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Sighature Name: Keven Su Title: Manager Company: TAIWAN BIOTRONIC TECHNOLOGY INC.

TAIWAN BIOTRONIC TECHNOLOGY INC. No.59-3, Sec. 2, Fuxing Rd., Wufeng Dist., Taichung City, 413 Taiwan Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road _ Columbia, MD 21046 Date: 2021-08-23 Request for Long-Term Confidentiality Company name: TAIWAN BIOTRONIC TECHNOLOGY INC. FCC ID: 2AAQQHRY FCC Part 15 Certification To whom it may concern:

In accordance with 0.457(d) and 0.459 of CFR 47, CLIMAX TECHNOLOGY CO., LTD. hereby requests Long-Term confidentiality of all Block Diagrams, Schematics, Operational Description attachments for the subject application. These documents contain detailed system and equipment description and related information about the product which TAIWAN BIOTRONIC TECHNOLOGY INC. considers to be proprietary, confidential and a custom design and otherwise would not release to the general public. Since the design is a basis from which future technological products will evolve, TAIWAN BIOTRONIC TECHNOLOGY INC. considers that this information would be of benefit to its competitors and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Sincerely, Sign ture stab :

Name: Keven Su Title: Manager Company: TAIWAN BIOTRONIC TECHNOLOGY INC.