G00-TPDBF13 Rev. 15/08-00 USER GUIDE 1 OVERVIEW OF THE LOCKSET OR 1 INDICATORS 1. Red light: Represents an incorrect entry or the unit is programming mode. 2. Yellow light: Flashes when the batteries are low in power. 3. Green light: Represents a correct entry. 4 BATTERY COVER 1. Protects the batteries from unexpected damage. 2 CLEAR BUTTON 1. Please always press button to cancel any typo or exit programming mode. C 5 [SET] BUTTON 1. Press set button for 1 second to enter programming mode. 2. Please refer to for more information about programming mode. 2 2-
3 MECHANICAL KEYWAY OVERRIDE 1. To unlock the lockset by a valid key. 6 INTERIOR THUMBTURN 1. Locks or unlocks the lockset manually. 2 HOW TO LOCK / UNLOCK / PROGRAM THE LOCKSET 1 HOW TO LOCK / UNLOCK THE LOCKSET To lock To unlock A A 1 2 3 4 5 6 7 8 9 c 0 Touch the screen to lock. B Use a mechanical key to lock. C Lock or unlock by mobile app. To unlock, enter valid User Code or Programming Code. B Use a mechanical key to lock. C Lock or unlock by mobile app. After the screen is activated, enter Guiding Code rst if it is on (see - ). 2 2
#
#
#
#
The screen is temporarily disabled after 4 consecutive incorrect entries. 2 HOW TO PROGRAM THE LOCKSET BASIC SETTINGS Change Programming Code Programming Code can be used to program or unlock the lockset. The default Programming Code is 12345678. Press [SET] for 1 second. Programming Code
(4~8 digits) Add a User Code(S) User Code can be used to unlock the lockset. User Code cappcity: 25 sets (4-8 digits). Press [SET] for 1 second. Programming Code
(4~8 digits) Delete individual User Code(S) Delete individual User Code(s). Delete ALL User Codes Delete ALL User Codes at once. Press [SET] for 1 second. Programming Code
(4~8 digits) Press [SET] for 1 second. Programming Code
(4~8 digits)
#
#
#
#
1 2 3 4 0 0 0 0
#
#
#
#
New Programming Code(4~8 digits) New User Code
(4-8 digits)
#
#
Same New Programming Code(4~8 digits) Same New User Code (4-8 digits) Add another code User Code Same User Code
#
Delete another code C ADVANCED SETTINGS Add Single-use User Code(S) Single-use User Code can only be used once to unlock the lockset. Single-use User Code capacity: 4 sets (4 digits). Press [SET] for 1 second. Programming Code
(4~8 digits)
#
2 1
#
Single-use User Code (4 digits)
#
Same Single-use User Code (4 digits) Add another code Guiding Code Guiding Code is a set of random codes to be entered prior to any User Code to prevent code probing by placing nger prints on every button making code discovery more difcult. Press [SET] for 1 second. Programming Code
(4~8 digits) Vacation Mode Vaction mode temporarily disable ALL User Codes. Press [SET] for 1 second. Programming Code
(4~8 digits) Volume Control Turn on / off door lock operation volume. Volume is always on in the programming mode. Press [SET] for 1 second. Programming Code
(4~8 digits) Auto-lock Auto-lock is disabled by default. Press [SET] for 1 second. Programming Code
(4~8 digits) Auto-lock Delay Timer Default Auto-lock Delay Timer : 10 seconds. Auto-lock Delay Timer range: 10 -99 seconds. Press [SET] for 1 second. Programming Code
(4~8 digits) Turn on inclusion / exclusion mode at your Z-Wave controller when including / excluding the lock. Refer to your Z-Wave controller instruction for more information. Press [SET] for 1 second. Programming Code
(4~8 digits) Include / Exclude to Z-Wave network The lockset will exit the programming mode and resume to the stand-by status if no input is made in 10 seconds. 3 Beeps means something was entered incorrectly. Please redo the step again.
#
#
#
#
#
#
2 2 5 6 8 7 0 0 0 0 9 0
#
#
#
#
#
#
Turn On Turn Off Turn On Turn Off Turn On Turn Off Turn On Turn Off 1 0 1 0 1 0 1 0
#
#
#
#
#
#
#
#
Enter New Amount (10 - 99)
#
Include / Exclude successfully (beep x 1) OR Include / Exclude unsuccessfully (beep x 3) 3 RESTORE TO FACTORY SETTINGS A A Remove one battery A A Press and hold SET button while inserting the battery back. Hold the set button until long beep has nished. 1. This will erase all stored information, including bolt direction 2. Please re-enter the default Programming Code to set up the lock after restoring tofactory settings. 3 TROUBLESHOOTING 1 INSTALLATION QUESTIONS ANSWERS A.The latch does not operate correctly after installation. 1. Please reset unit to factory settings and set bolt direction. 2. Make sure prior to installation latch bolt is retracted and key as not in lockset when placing torque blade horizontally through latch. QUESTIONS K. The red indicator is still on after setting is completed. ANSWERS 1. Check if [SET] button is jammed. 2. Re-install the batteries. L. The lockset locks when I enter my code and unlocks when I touch the screen. 1. Un-install the interior and exterior assemblies. Before re-installation, please follow these guidelines:
1) Make sure the bolt is in the retracted position. 2) Do not have any key in lock cylinder. 3) Make sure the torque blade is inserted horizontally. 4) Reset unit back to factory settings and follow steps for setting bolt direction. M. I cannot remove my key unless it is in the locked position. 1. Un-install the interior and exterior assemblies. Before re-installation, please follow these guidelines:
1) Make sure the bolt is in the retracted position. 2) Do not have any key in lock cylinder. 3) Make sure the torque blade is inserted horizontally. N. I cannot include my lock to Z-Wave network. 1. Performe the exclusion process then perform the inclusion process again. 2. Make sure the lock is within the Z-Wave network range. 3. Refer to your Z-Wave controller instruction for more information. 1. Please execute lock & unlock function to allow the motor to reposition itself again. 2. Redo the Automatic Bolt Direction Step. If the lock appears to be damaged or does not operate properly, please contact customer service for further assistance. B. Feel a bump while turning the thumbturn or the key?
2 OPERATION QUESTIONS ANSWERS A. Battery indicator keeps ashing. 1. The batteries are getting low, please replace with four new batteries for the best performance
(alkaline batteries only ). B. Touch screen not responding. 1. Check the battery installation. 2. The batteries are getting low if the battery indicator keeps ashing. please replace with four new batteries for the best performance (alkaline batteries only ). 3. Make sure the cable is well-connected to the port, and was not damaged during installation. C. Programming Code can not be changed. 1. Please refer to in the user guide to restore factory setting and reprogram all codes.
- 32 D. What should I do if wrong code was entered?
1. Press button once and continue to input code according to regular procedures. C DECLARATIONS AND SAFETY STATEMENTS FEDERAL COMMUNICATIONS COMMISSION STATEMENT GARANTIE ET DCLARATIONS DE SCURIT DCLARATION DE LA FEDERAL COMMUNICATIONS COMMISSION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. IC REGULATIONS This device complies with Industry Canada licence-exempt RSS-210 standard. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. Ce produit est conforme la section 15 des rgles de la FCC. Son fonctionnement est soumis aux deux conditions suivantes :
(1) Ce dispositif ne peut pas causer d'interfrence prjudiciable, et (2) ce dispositif doit accepter toute interfrence reue, y compris une interfrence qui peut engendrer un fonctionnement indsirable. Toute altration ou modication non expressment approuve par la partie responsable dassurer la conformit pourrait annuler lautorit de lutilisateur utiliser cet quipement. REMARQUE : Cet quipement a t test et tabli conforme aux limites inhrentes portant sur des appareils numriques de classe B, en vertu de l'article 15 des rgles de la FCC. Ces limites sont conues pour offrir une protection raisonnable contre une interfrence nuisible dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre de lnergie en radiofrquence et, sil nest pas install et utilis conformment aux instructions, peut causer des interfrences prjudiciables aux communications radio. Cependant, il nest pas garanti que des interfrences ne se produiront pas dans une installation particulire. Si cet quipement cause des interfrences prjudiciables la rception des postes de radio ou de tlvision, ce qui peut tre dtermin en teignant et en allumant l'quipement, l'utilisateur est e ncourag essayer de corriger l'interfrence en appliquant une ou plusieurs des mesures suivantes :
Rorienter ou dplacer lantenne de rception. Accrotre la distance entre lquipement et lappareil de rception. Brancher lquipement dans une prise dont le circuit nest pas le mme que celui sur lequel lappareil de rception est branch. Consulter le fournisseur ou un technicien spcialis en radio / TV pour assistance. RGLEMENTS D'IC Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. Son utilisation est soumise aux deux conditions suivantes :(1) Cet appareil nest pas susceptible de causer des interfrences nuisibles, et (2) cet appareil doit pouvoir supporter les interfrences reues, y compris celles susceptibles de causer un fonctionnent non souhait de lappareil. 4 Access code list E. Can not delete all User Codes . 1. Make sure the whole code entering process is completed within 10 seconds, otherwise the unit will time out. 2. Make sure the Programming Code has been entered correctly. Do not pass your Programming Code to anyone else. Programming Code Name User Code F. Can not add a new User Code. 1. Make sure the whole code entering process is completed within 10 seconds, otherwise the unit will time out. 2. Make sure the Programming Code has been entered correctly. 3. The new User Code will not be accepted when the capacity is full. Try to delete any or some existing User Codes and then add new one(s) again. A User Code must be at least 4 to 8 digits. G. "Auto lock" does not function. 1. The batteries are getting low if the battery indicator keeps ashing. please replace with four new batteries for the best performance (alkaline batteries only ). H. Lockset is not able to unlock by touch screen. 1. Make sure you have entered the correct User Code. 2. The battery is low if the battery indicator light keeps ashing. Please replace with four new batteries. 3. Check the strike plate to make sure it is properly aligned & clear so the bolt can freely enter the hole. I. Lockset is unable to reset. 1. Please refer to in the user guide to restore factory setting. 2. The battery is low if the battery indicator light keeps ashing. Please replace with four new batteries.
- 32 J. How to operate the lockset in darkness?
1. Touch the screen to activate the lockset back light.