NT503 USB DAC / NETWORK PLAYER User Manual

 

Z NT-503 USB DAC/ Network Player D01252920A ENGLISH FRANAIS ESPAOL OWNERS MANUAL MODE DEMPLOI MANUAL DEL USUARIO IMPORTANT SAFETY INSTRUCTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

< The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magni-

tude to constitute a risk of electric shock to persons. B The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION o DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE INSIDE. o IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT, CONTACT THE STORE WHERE YOU PURCHASED THE UNIT FOR A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS BEEN REPAIRED. o USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are pro-

vided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched par-

ticularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the man-

ufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate nor-

mally, or has been dropped. o The apparatus draws nominal non-operating power from the AC outlet with its POWER or STANDBY/ON switch not in the ON position. o The power plugs are used as disconnect devices; the disconnect devices shall remain readily operable. o Caution should be taken when using earphones or headphones with the product because excessive sound pressure (volume) from earphones or headphones can cause hearing loss. 2 CAUTION For European Customers o Do not expose this apparatus to drips or splashes. o Do not place any objects filled with liquids, such as vases, on the apparatus. o Do not install this apparatus in a confined space such as a book case or similar unit. o The apparatus should be located close enough to the AC outlet so that you can easily reach the power cord plug at any time. o If the product uses batteries (including a battery pack or installed batteries), they should not be exposed to sunshine, fire or excessive heat. o CAUTION for products that use replaceable lithium batter-

ies: there is danger of explosion if a battery is replaced with an incorrect type of battery. Replace only with the same or equivalent type. WARNING Products with Class ! construction are equipped with a power supply cord that has a grounding plug. The cord of such a prod-

uct must be plugged into an AC outlet that has a protective grounding connection. IN USA/CANADA, USE ONLY ON 120 V SUPPLY. V Precautions concerning batteries Misuse of batteries could cause them to rupture or leak leading to fire, injury or the staining of nearby things. Please read and observe the following precautions carefully. o Be sure to insert the batteries with correct positive () and negative (^) orientations. o Use batteries of the same type. Never use different types of bat-

teries together. o If the remote control is not used for a long time (more than a month), remove the batteries to prevent them from leaking. o If the batteries leak, wipe away the leakage inside the battery compartment and replace the batteries with new ones. o Do not use batteries of types other than those specified. Do not mix new batteries with old ones or use different types of batter-

ies together. o Do not heat or disassemble batteries. Never throw batteries into fire or water. o Do not carry or store batteries with other metallic objects. The batteries could short circuit, leak or explode. o Never recharge a battery unless it is confirmed to be a recharge-

able type. Disposal of electrical and electronic equipment and batteries and/or accumulators a) All electrical/electronic equipment and waste batteries/

accumulators should be disposed of separately from the municipal waste stream via collection facilities designated by the government or local authorities. b) By disposing of electrical/electronic equipment and waste batteries/accumulators correctly, you will help save valuable resources and prevent any potential negative effects on human health and the environment. c) Improper disposal of waste electrical/electronic equipment and batteries/accumulators can have serious effects on the environment and human health because of the presence of hazardous substances in the equipment. d) The Waste Electrical and Electronic Equipment (WEEE) symbols, which show wheeled bins that have been crossed out, indicate that electrical/electronic equip-

ment and batteries/accumulators must be collected and disposed of separately from household waste. If a battery or accumulator contains more than the specified values of lead (Pb), mercury (Hg), and/or cadmium (Cd) as defined in the Battery Directive

(2006/66/EC), then the chemical symbols for those elements will be indicated beneath the WEEE symbol. Pb, Hg, Cd e) Return and collection systems are available to end users. For more detailed information about the disposal of old electri-

cal/electronic equipment and waste batteries/accumulators, please contact your city office, waste disposal service or the shop where you purchased the equipment. DECLARATION OF CONFORMITY We, TEAC AUDIO EUROPE, Liegnitzer Strae 6, 82194 Grbenzell, Germany declare in own responsibility, the TEAC product described in this manual is in compliance with the corresponding technical standards. The nameplate is located on the bottom of the unit as shown below. Front side Nameplate 3 EN Wireless equipment precautions Compliance of radio transmitter and interference Model for USA Declaration of Conformity Responsible party:

TEAC AMERICA, INC. Address: 1834 Gage Road, Montebello, California, U.S.A. Telephone number : 1-323-726-0303 This device complies with Part.15 of FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause interference 2) This device must accept any interference, including interfer-

ence that may cause undesired operation of the device. Labeling of authorization FCC ID: XEG-NT503 Model for Canada Compliance of radio transmitter This device complies with Industry Canada RSS standard(s). Operation is subject to the following two conditions:

1) This device may not cause interference 2) This device must accept any interference, including interfer-

ence that may cause undesired operation of the device. Labeling of authorization IC: 1559C-NT503 Compliance of interference This Class B digital apparatus complies with Canadian ICES-003. Model for EEA (European Economic Area) This equipment complies with the harmonised standards of DIRECTIVE 1999/5/EC (R&TTE). Labeling of conformity CE marking:

CAUTION Authorization of wireless devices are different in countries or regions. Please use only in the country where you purchased the product. o Depending on the country, restrictions on the use of Bluetooth wireless technology might exist. Confirm the laws and regulations of the country or region where you want to use the unit before use. 4 Radiation Exposure requirements This equipment meets the regulation, which is recognized interna-

tionally, for the case of human exposure to radio waves generated by the transmitter. Statement of compliance Model for USA This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio fre-

quency Exposure Guidelines. Model for Canada This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. Model for EEA (European Economic Area) This equipment complies with EN.62311; Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields; the harmonised standard of DIRECTIVE 1999/5/EC. CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Information for interference

(FCC requirements) This equipment has been tested and found to comply with the lim-

its for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. o Reorient or relocate the equipment and/or the receiving antenna. o Increase the separation between the equipment and receiver. o Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. o Consult the dealer or an experienced radio/TV technician for help. Trademarks and other legal statement MPEG Layer-3 audio coding technology licensed from Fraunhofer IS and Thomson.

"DSD" is a registered trademark. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by TEAC CORPORATION is under license. 2013 CSR plc and its group companies. The aptX mark and the aptX logo are trade marks of CSR plc or one of its group companies and may be registered in one or more jurisdictions. This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft. Windows and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Mac, Mac OS and OS X are trademarks of Apple Inc., registered in the U.S. and other countries. IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license. Android is a trademark of Google Inc. SiriusXM Internet Radio subscriptions are sold separately and are governed by the Sirius Terms and Conditions (see www.sirius.com). Be sure to read this agreement before you purchase your subscrip-

tion. Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. and its subsidiaries. All rights reserved. Slacker and the Slacker Logo are registered trademarks of Slacker, Inc. DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks, service marks, or certification marks of the Digital Living Network Alliance. Other company names and product names in this document are the trademarks or registered trademarks of their respective owners. Information about copyrights and licensing related to open-source software is provided in the separate Important Notice Regarding Software document. Listening to SiriusXM Internet Radio To listen to SiriusXM Internet Radio, youll need to subscribe to SiriusXM Internet Radio service and obtain a username and password. SiriusXM Internet Radio is available to residents of the United States and Canada. SiriusXM Internet Radio delivers a variety of commercial-free music including Pop, Rock, Country, R&B, Hip-Hop, Jazz, Classical and much more, plus expert sports talk and analysis. You also get exclusive entertainment, talk, comedy, family programming, local traffic and weather and news from your most trusted sources. Once youve purchased a SiriusXM Internet Radio compatible tuner youll need to subscribe to the service to listen to SiriusXM Internet Radio. There are a variety of programming packages available, including the option of adding The Best of XM pro-

gramming to the SiriusXM Internet Radio service. The Best of XM service is not available to Sirius Canada subscribers at this time. Please check with Sirius Canada for any updates using the num-

bers and web address below. Family friendly packages are also available to restrict channels that feature mature programming. To subscribe to SiriusXM Internet Radio, U.S. customers should visit www.sirius.com or call 1-888-539-SIRI (1-888-539-7474). Canadian customers should visit www.siriuscanada.ca. Current XM Radio Online subscribers will need to log into the XM online account manager and update their password in order for their credentials to work on a SiriusXM Internet Radio compat-

ible device. If the username is over 20 characters or their device doesnt support the @ character in the username, subscribers need to update the username on the same screen. 5 EN Contents Included items Thank you for choosing TEAC. Read this manual carefully to get the best performance from this unit. After reading it, keep it in a safe place with the warranty card for future reference. Check to be sure the box contains all the included items shown below. Please contact the store where you purchased this unit if any of these items are missing or have been damaged during transportation. Included items . 6 Before use . 7 Maintenance . 7 Using the TEAC Global Site . 7 Product registration . 7 USB flash drives and Networks . 8 Downloading the remote app . 9 Connections . 10 Connections (front panel) . 12 Connecting headphones . 13 Upconversion . 13 Names and functions of parts (main unit) . 14 Using the remote control . 15 Names and functions of parts (remote control) . 16 Basic operation . 17 Display . 18 Bluetooth wireless technology . 20 Settings . 22 Playing back music on a computer . 27 Troubleshooting . 29 Specifications . 31 Power cord 1 RCA conversion (RCA to mini plug) cable 1 Remote control (RC-1320) 1 Batteries for remote control (AAA) 2 Owners manual (this document) 1 o Keep this manual in a safe place for future reference. Warranty card 1 (for users in the USA and Canada only) o Users in Europe and other countries and regions should see the back of this document for information about the warranty. 6 Before use Maintenance V Precautions for use o Do not install this unit in a location that could become hot. This includes places that are exposed to direct sunlight or near a radiator, heater, stove or other heating equipment. Moreover, do not place it on top of an amplifier or other equipment that generates heat. Doing so could cause discoloration, deformation or malfunction. o Avoid locations that are extremely cold or exposed to excessive humidity or dust. o When installing this unit, leave a little space (at least 3 cm or 8") between it and walls and other devices in order to allow good heat dissipation. If you put it in a rack, for example, leave at least 5 cm (2") open above it and at least 10 cm (4") open behind it. Failure to provide these gaps could cause heat to build up inside and result in fire. o Place the unit in a stable location near the audio system that you will use with it. o DO NOT place anything, not even CDs, CD-Rs, LP records or cas-

sette tapes, on top of the units. Doing so could cause damage. o The voltage supplied to the unit should match the voltage printed on the rear panel. If you are in any doubt regarding this matter, consult an electrician. o Do not move the unit during use. o Do not open the body of the unit because this could result in damage to the circuitry or cause electric shock. If a foreign object should enter the unit, contact your dealer. o When removing the power plug from the wall outlet, always pull directly on the plug; never yank on the cord. Wipe dirt from the top cover and other panel surfaces using a soft cloth that has been slightly dampened with a diluted neutral cleanser. Do not wipe with chemical cleaning cloths, thinner or other chemi-

cal agents. Doing so could damage the surface. V For your safety, disconnect the power cord from the socket before cleaning. Using the TEAC Global Site You can download updates for this unit from the TEAC Global Site:

http://teac-global.com/

1) Open the TEAC Global Site. 2) In the TEAC Downloads section, click the desired language to open the Downloads website page for that language. NOTE If the desired language does not appear, click Other Languages. 3) Click the Search by Model Name section to open the Downloads page for that product. (Users in Europe should click the product name in the Products section instead.) 4) Select and download the updates that are needed. Product registration Customers in the USA, please visit the following TEAC website to register your TEAC product online. http://audio.teac.com/support/registration/

7 EN USB flash drives and Networks Audio files playable by this unit This unit can play the following types of audio files from USB flash drives or over a network connection. MP3 File extension Standard Sampling frequency 8kHz, 11.025kHz, 12kHz, 16kHz, 22.05kHz,

.mp3, .MP3 MPEG-1/MPEG-2 Audio Layer-3 Bit rate 24kHz, 32kHz, 44.1kHz, 48kHz 8 kpbs 320 kbps or VBR WMA File extension Sampling frequency 8kHz, 11.025kHz, 16kHz, 22.05kHz, 32kHz,

.wma, .WMA Bit rate o This unit might not be able to play audio files with copyright 44.1kHz, 48kHz 5 kpbs 320 kbps or VBR protection from a USB or network source. o WMA Pro/Voice not supported WMA Lossless File extension Sampling frequency 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz Quantization bit depth

.wma or .WMA 16-bit, 24-bit WAV File extension Sampling frequency 8kHz, 11.025kHz, 12kHz, 16kHz, 22.05kHz,

.wav, .WAV 24kHz, 32kHz, 44.1kHz, 48kHz, 64kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz 8-bit, 16-bit, 24-bit Quantization bit depth o WAV files include uncompressed PCM digital audio. AAC File extension

.aac, .m4a, .mp4, .3gp, .3g2,

.AAC, .M4A, .MP4, .3GP, .3G2 MPEG-2/MPEG-4 Audio Standard Sampling frequency 8kHz, 11.025kHz, 12kHz, 16kHz, 22.05kHz, Bit rate 24kHz, 32kHz, 44.1kHz, 48kHz, 64kHz, 88.2kHz, 96kHz 8 kpbs 320 kbps or VBR FLAC File extension Sampling frequency 8kHz, 11.025kHz, 16kHz, 22.05kHz, 32kHz,

.flac, .FLAC 44.1kHz, 48kHz, 64kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz 8-bit, 16-bit, 24-bit Quantization bit depth Ogg Vorbis File extension Sampling frequency 8kHz, 11.025kHz, 16kHz, 22.05kHz, 32kHz,

.ogg, .OGG Bit rate o Incompatible files cannot be played back. 44.1kHz, 48kHz, 64kHz 48 kpbs 500 kbps or VBR 8 Apple Lossless File extension Sampling frequency 8kHz, 11.025kHz, 12kHz, 16kHz, 22.05kHz,

.m4a, .mp4, .M4A, .MP4 24kHz, 32kHz, 44.1kHz, 48kHz, 64kHz, 88.2kHz, 96kHz 16-bit, 24-bit Quantization bit depth DSD File extension Sampling frequency 2.8MHz, 5.6MHz

.dsf, .DSF ATTENTION o This unit does not support the following formats when using the Play To feature of Windows Media Player. FLAC, Ogg Vorbis, DSD o When playing back audio files over a network, the types of file formats that can be played back also depend on the soft-

ware running on the network server. For example, when using Windows Media Player, not all audio files on the computer can be played back. Only audio files that have been added to the Windows Media Player library can be played back. o When playing back files that have been recorded at variable bit rate (VBR), the playback time might not be shown correctly. Notes about USB flash drives This unit can use USB flash drives.*

Connect USB flash drives to the USB port (front).

* The USB ports on this unit only support USB flash drives (also known as thumb drives and jump drives). They do not support standard USB hard drives. o FAT16 and FAT32 formats are supported for USB flash drives. o If a USB flash drive is divided into multiple partitions, this unit will recognize them as separate volumes. o This unit supports up to 20,000 files and 16 folder levels within a single folder. o This unit does not support USB hubs or devices with USB hub functions. Never connect such devices to this unit. ATTENTION o If the connected media is not supported, "Not Connected"

appears on this unit's display. o This unit cannot play back audio files if copyright protection is used. o Do not connect this unit's USB port (front) to a computer. Sound from a computer cannot be input through this unit's USB port (front). o This unit might not be able to use media that is loaded into a USB card reader. o Depending on the USB flash drive and its contents, reading data from it might take some time. Downloading the remote app o Depending on the USB flash drive, the unit might not be able to read its data correctly or supply power properly. o During the use of USB flash drives, please be aware that our com-

pany will take no responsibility should data be lost or changed, a USB flash drive become damaged or other harm occur. o We recommend backing up data saved on a USB flash drive before using it with this unit. o This unit does not support USB flash drives with security functions. To play back files on USB flash drives and to use the unit connected to a network, install the dedicated app (free) on a smartphone, and connect it to the same network as the unit. If you install the app on an iPod touch/iPhone or Android device, you can use it over a wireless network for basic control of the unit. o You can download and use the app for free. Note about DLNA The Digital Living Network Alliance (DLNA) is a group that is advanc-

ing the standardization of reciprocal connections and the exchange of audio, image, video and other data among computers, game devices and digital household appliances over ordinary home networks (LAN). This unit complies with version 1.5 of the DLNA guidelines. Note about servers This unit supports the following version of Windows Media Player. uWindows Media Player 12 uServers that comply with DLNA A network server must be connected to the same network as this unit. This unit supports up to 20,000 files and 16 folder levels within a single folder. ATTENTION Depending on the type of media server, this unit might not recog-

nize it or be able to play audio files saved on it. Note about network services The network services that can be used will differ according to the region. Network services and contents that you can use through this unit could become unusable without warning if the service provider stops service. How to download the iPod touch/iPhone app Search for "TEAC HR Remote" in the App Store. How to download the Android app Search for "Teac Avr Remote" on the Google play website (https://

play.google.com/store). 9 EN Connections Device that outputs clock signal CLOCK SYNC OUT Digital audio output device Digital audio output device DIGITAL OUT

(COAXIAL) DIGITAL OUT

(OPTICAL) 5 0 B N C c o a x i a l c a b l e R C A c o a x i a l i d g i t a l c a b l e O p t i c a l i d g i t a l c a b l e A B C D E X L R c a b l e s Connect cables for the pair set for line output

(page 23). Sound will only be output from the selected pair. If headphones are connected, sound will stop being output from the rear panel connectors. The polarity of the XLR connectors can be set so that either 2 or 3 is HOT

(page 23). F G I n c l u d e d p o w e r c o r d U S B c a b l e If using a Windows OS, install the dedicated driver on the computer before connecting this unit to it

(page 27). c Wall outlet R C A a u d o c a b l e s i Connect a set of cables of one type or the other. R L L R Audio input

(LINE IN, etc.) Stereo amplifier or powered speakers Computer 10 A ETHERNET port F USB port (rear) Connect a commercially-available LAN cable to this port when you want to connect this unit to a wired network or the Internet. o When switching input sources, this port is labeled "NET". Use to input digital audio from a computer. Connect it to a computer's USB port. Use a commercially-available USB2.0 cable (A-B type) for this connection. B CLOCK SYNC input connector (10MHz IN) Input a synchronization signal (clock sync) here. To input a 10MHz oscillator signal (sine wave output), connect the oscillator output here. o Use a commercially-available BNC coaxial cable (50 ) for connection. o Clock sync is only possible when the input source is USB, USBf or NET. C RCA COAXIAL digital audio input connector Use this to input digital audio. Connect the coaxial digital audio output connector of a digital audio device to it. Use a commercially-available RCA coaxial digital cable for connection. D OPTICAL digital audio input connector Use this to input digital audio. Connect the optical digital audio output connector of a digital audio device to it. Use a commercially-available optical digital cable for connection. E Analog audio output connectors (LINE OUT) These output 2 channels of analog audio. Connect these XLR or RCA connectors to a stereo amplifier or powered speakers. Use commercially available cables for connections. XLR: balanced XLR cables RCA: RCA audio cables Connect this unit's R connector to the R connector of the amplifier and its L connector to the L connector of the amplifier. ATTENTION Before connecting a computer that is running a Windows OS, you must install the dedicated driver on the computer (page 27). Proper connection is not possible with a computer that does not have this driver installed. G Power inlet (~IN) Insert the included power cord here. After completing all other connections, insert the power plug into a power outlet. V Use only the included power cord. Use of other power cords could result in fire or electric shock. Unplug the cord from the outlet when not using the unit for a long time. V Complete all other connections before turning the unit on. o Carefully read the manuals of the devices that you are connecting and follow their instructions when making connections. o Do not bundle connecting cables with power cords. Doing so could cause noise. o Connect all plugs completely. 11 EN Connections (front panel) USB flash drives Connect USB flash drives to the USB port on the front of the unit. To play music files on a USB flash drive, set the input source to NET and use the app for playback. o The f indicates the front panel. Coaxial (COAX) connection Use the included RCA conversion cable and a commercially-avail-

able RCA coaxial digital cable. To enable this input, turn the INPUT SELECTOR knob to select COAXf. o The f indicates the front panel. Digital audio input (OPT/COAX IN) This input connector can be used for both optical (OPT) and coaxial

(COAX) connections. Optical (OPT) connection Use a commercially-available optical cable with a mini plug. To enable this input, turn the INPUT SELECTOR knob to select OPTf. o The f indicates the front panel. RCA conversion cable RCA coaxial digital cable Optical mini plug 12 Connecting headphones Upconversion You can use the upconversion function with digital input, includ-

ing the OPT/COAX IN connector, and the USB (front) and USB (rear) ports. (page 23). The relationships between input sampling frequencies and sam-

pling frequencies after upconversion are as follows. Input source Upconversion setting Digital audio input USB OFF 2Fs 4Fs 8Fs DSD Input sampling frequency

[kHz]

Sampling frequency after upconversion

[kHz]

[MHz]

32 44.1 88.2 176.4 48 96 192 44.1 88.2 176.4 352.8 48 96 192 384 32 44.1 88.2 176.4 352.8 48 96 192 384 64 88.2 88.2 176.4 352.8 96 96 192 384 128 176.4 176.4 176.4 352.8 192 192 192 384 256 352.8 352.8 352.8 352.8 384 384 384 384 8.0 11.2 11.2 11.2 11.2 12.2 12.2 12.2 12.2 Values indicated by are unchanged. V CAUTION While wearing headphones, do not connect or disconnect them or turn the unit on or off. Doing so could result in a sudden loud noise that could harm your hearing. Always set the volume to minimum ( dB) before putting head-

phones on (page 17). 13 EN Names and functions of parts (main unit) A B C D E F G H I J A POWER switch C Digital audio input (OPT/COAX IN) Use to turn the unit on and off. o If the display is dark even though the POWER switch is set to ON, the cause is usually one of the following. The power is on, but DIMMER (display brightness) is set to OFF (page 24). The automatic power saving function has put the unit into standby. The power cord is disconnected. To turn the unit on, press the STANDBY/ON button on the remote control, or set the power switch to OFF once and then back to ON. B CLOCK indicator This shows the clock synchronization status. Lit:

The unit is synchronized with the clock from the CLOCK SYNC input connector (10MHz IN). Blinking: No clock is being input or the unit is not being synchronized. No clock sync is occurring. Unlit:

o See page 23 for clock sync settings. Use this to input digital audio (page 12). Optical connection: Use an optical cable with a mini plug. Coaxial connection: Use the included RCA conversion cable. D INPUT SELECTOR knob Use to select the input source. Use to change setting values when a menu item is shown. Press to use as an ENTER button. Turn when the menu is open to change the item shown or the setting value. E MENU button Press to enter setting mode (page 22). Press when in setting mode to return to the previous screen. F Remote control signal receiver This receives signals from the remote control. When operating the remote control, point it at the remote control signal receiver. 14 Using the remote control G USB port (front) Connect USB flash drives here. o To play music files on a USB flash drive, set the input source to NET and use the app for playback. o Do not connect this unit's USB port (front) to a computer. Sound from a computer cannot be input through this unit's USB port (front). H PHONES jack Connect headphones with a standard 6.3 mm (1/4") stereo plug here (page 13). o If headphones are connected to this unit, audio will not be output from the analog audio outputs on the rear panel. I Display This display shows information about the audio playing back and menu screens. J VOLUME knob Use to adjust the headphones output volume. Turn right to increase and left to decrease the volume. o To enable adjustment of this unit's analog audio output volume, set LINE OUT LEVEL to VARIABLE (Line output level on page 24). This will enable adjustment of the analog output level using this unit's VOLUME knob. o Volume settings are retained separately for analog audio output and headphone output. Precautions for use V Misuse of batteries could cause them to rupture or leak, which might result in fire, injury or the stain-

ing of nearby materials. Please carefully read and observe the precautions on page 3. o When using the remote control, point it toward the remote con-

trol signal receiver on the main unit from a distance of 5 m (16 ft) or less. Do not place obstructions between the main unit and the remote control. o The remote control might not work if the remote control signal receiver on the unit is exposed to direct sunlight or bright light. If this occurs, try moving the unit. o Beware that use of this remote control could cause the unin-

tentional operation of other devices that can be controlled by infrared rays. Installing batteries Remove the cover from the back of the remote control and insert two AAA batteries with their /^ ends oriented in the case as shown. Replace the cover. When to replace batteries If the distance required between the remote and the main unit decreases or if the unit stops responding to the remote buttons, replace both batteries with new ones. Dispose of the used batteries according to the instructions on them or requirements set by your local municipality. 15 EN Names and functions of parts (remote control) a b c d e f g h i j a STANDBY/ON button A Press to put the unit into standby mode or turn it on. b INPUT buttons Use to select the playback source. o The USB button selects the rear USB port. o The TUNER button is not used with this unit. c UPCONVERT button Use to change the upconversion setting. d FILTER button Use to change the filter setting. This changes the filter according to the input (PCM or DSD). e Up/down (k/j) buttons Use to select setting items. f MUTE button Press to minimize the volume. g DIMMER button Use to adjust the brightness of the main unit's display. h MENU button Press to enter setting mode (page 22). Press when in setting mode to return to the previous screen. i ENTER button Press to confirm the selected item. j VOLUME (+/) buttons Use these buttons to adjust the volume. When the main unit and the remote control both have buttons with the same functions, this manual explains how to use one of the buttons. The other corresponding button can be used in the same manner. 16 1 Shift the POWER switch to its ON position to turn 3 Operate the playback device. Basic operation the unit on. o If a stereo amplifier is connected to this unit, always turn its power ON very last. Refer to the operation manual of that device. 4 Adjust the volume. When using the line outputs When LINE OUT LEVEL is set to VARIABLE, turn this unit's VOLUME knob to adjust the volume. When LINE OUT LEVEL is set to any other setting, the volume cannot be adjusted from this unit. Use the stereo amplifier or other device connected to this unit to adjust the volume. When headphones are connected to this unit Turn this unit's VOLUME knob to adjust the volume. o When this unit's VOLUME knob is enabled, the volume set-

2 Turn the INPUT SELECTOR knob to select the input ting will be shown. source. The selected source appears on the display. o You can also use the up and down (k, j) buttons on the remote control. o If the input signal is not a digital audio signal or is an audio signal format that is not supported by this unit, such as Dolby Digital or DTS, NOT AUDIO! will appear on the screen and no audio will be output. Set the digital output of the connected device to PCM audio output. o To use a computer running a Windows OS to play back audio files when this unit is set to USB, you must first install a dedicated driver on the computer before connecting them

(page 27). o DSD data can only be played back using the front and rear USB ports or a DoP format digital input. o To use NET or the front USB port, install the dedicated app

(free) on a smartphone, and connect it to the same network as the unit. 17 EN Display When on WELCOME c TEAC NT-503 Input source name This shows the name of the selected source. The names shown on the display correspond to the selected con-

nectors as follows. USB USB port (rear) COAX RCA COAXIAL digital audio input connector on the rear panel COAXf Coaxial connection with the digital audio input (OPT/COAX IN) on the front panel After the above messages appear, the input source will be shown on the display. OPT OPTICAL digital audio input connector on the rear panel Input source information display The input source information display will appear after turning the unit on as well as when about 10 seconds pass without operation when a setting screen is open. Display example When headphones are not connected and LINE OUT LEVEL is set to FIX or OFF Digital filter setting Audio data processing method Input source name USB ORG DF OFF PCM 44.1kHz Input signal status o Turning the VOLUME knob will not change the volume. When headphones are connected or LINE OUT LEVEL is set to VARIABLE USB ORG DF OFF PCM 44k -41.5dB Input signal status Volume o Turning the VOLUME knob will change the volume, and the vol-

ume will appear to the right of the input signal status. OPTf Optical connection with the digital audio input (OPT/COAX IN) on the front panel NET ETHERNET port USBf USB port (front) o Set the input source to NET and then select this with the app. Bluetooth Bluetooth device Audio data processing methods ORG The original input signal is sent directly to the D/A converter without upconversion. 2Fs 4Fs 8Fs DSD The upconversion shown will be used (page 23). DoP DSD signal is received by DoP (DSD over PCM) method. Digital filter setting This shows the digital filter setting (page 23). 18 Volume display The volume setting will be shown when you turn this unit's VOLUME knob. Display example Volume -60.0dB Input signal status This shows the input source signal status. UNLOCK!

The unit cannot synchronize with the input signal. NOT AUDIO!

A signal with a format that cannot be played is being received. UNCONNECTED!

The input source is USB (rear USB port), but no USB cable is con-

nected to the unit. The input source is NET, but no USB cable is connected to the unit. The input source is USBf (front USB port), but no USB flash drive is connected to the unit. READY The input source is USB (rear USB port), NET or USBf (front USB port) and a device is connected, but no audio signal is being received. ANALOG The input source is the analog audio inputs. PCM 32kHz PCM 44.1kHz PCM 48kHz PCM 88.2kHz PCM 96kHz PCM 128kHz PCM 176.4kHz PCM 192kHz PCM 256kHz PCM 352.8kHz PCM 384kHz DSD 2.8MHz DSD 5.6MHz DSD 11.2MHz These show the input signal type and sampling frequency. SBC AAC aptX When the input source is Bluetooth, the codec type is shown. 19 EN Bluetooth wireless technology Bluetooth notes When using this unit with a mobile phone or other Bluetooth devices, they should be no more than about 10 m (33 ft) apart. Depending on the circumstances of use, however, the effective transmission distance might be shorter. Wireless communication with every device that supports Bluetooth wireless technology is not guaranteed. To determine the compatibility between this unit and another device that supports Bluetooth wireless technology, refer to that device's operation manual or contact the shop where you pur-

chased it. Profiles This unit supports the following Bluetooth profiles. o A2DP (Advanced Audio Distribution Profile) o AVRCP (Audio/Video Remote Control Profile) In order to transfer audio using Bluetooth wireless transmission, the Bluetooth device must support A2DP. In order to control playback on the Bluetooth device, it must sup-

port AVRCP. Even if a Bluetooth device supports the same profiles, though, its functions might differ according to its specifications. Codecs This unit supports the following codecs. It will automatically select one of them during audio transfer. o SBC o AAC o aptX The unit will select the appropriate codec to use according to the codec compatibility of the other Bluetooth device and communica-

tion conditions. NOTE You cannot select the codec to be used by pressing a button, for example. Due to characteristics of Bluetooth wireless technology, playback from a Bluetooth device will be slightly delayed compared to play-

back from this unit. Content protection This unit supports SCMS-T as a form of content protection when transmitting audio, so it can play protected audio. Transmission security This unit supports security functions during Bluetooth wireless transmission in accordance with the Bluetooth standard specifica-

tions, but it does not guarantee the privacy of such transmissions. TEAC CORPORATION will bear no responsibility should an informa-

tion leak occur during Bluetooth wireless transmission. Pairing with another Bluetooth device Pairing this unit with another Bluetooth device is necessary the first time you connect with that Bluetooth device. 1 Turn the INPUT SELECTOR knob to select Bluetooth. Bluetooth UNCONNECTED 2 Enable Bluetooth transmission on the other Bluetooth device. 3 Press and hold the INPUT SELECTOR knob to enter pairing mode. Bluetooth PAIRING o PAIRING blinks when pairing. 4 On the other Bluetooth device, select "NT-503" (this unit). After this unit enters pairing mode, pair with it from the other Bluetooth device. For details, refer to the operation manual of that Bluetooth device. After connection, the display will show the input source. o If a request for a passcode appears on the screen of the Bluetooth device, enter 0000 (four zeros). 20 Playback from a Bluetooth device o Pair this unit the first time you use it and when you want to con-

nect it with a new Bluetooth device (page 20). o When pairing or connecting with another Bluetooth device, they should be within a few meters of each other. If they are too far apart, pairing and connection afterwards might become impossible. 5 Turn the INPUT SELECTOR knob to select Bluetooth. 8 Press the INPUT SELECTOR knob to connect. o If there are multiple paired devices, turn the INPUT SELECTOR knob to show other devices. When the name of the device that you want to connect is shown, press the INPUT SELECTOR knob. After connection, the display will show the input source. Display example Device name Bluetooth UNCONNECTED This sets the source to Bluetooth. o You can also use the up and down (k, j) buttons on the remote control. o The unit retains the same source mode even when in standby. So, this step can be skipped if the unit had already been in Bluetooth mode when it was put into standby. 6 Enable Bluetooth transmission on the other Bluetooth device. 7 Press the INPUT SELECTOR knob to show already paired Bluetooth devices. The bottom line of the display shows the name of the last con-

nected device. o You can also use the ENTER button on the remote control. Display example Bluetooth

> Player_1 Name of last connected device o The first 14 characters of the device name are shown. o If no paired device is available, the display will appear as follows. Bluetooth PAIRING?

Press and hold the INPUT SELECTOR knob to enter pairing mode (page 20). Playe ORG DF-OFF PCM 44k -41.5dB o The first 5 characters of the device name are shown. V ATTENTION Regardless of the connection status of this unit and the other Bluetooth device, if the input source is not shown, restart both this unit and the other device and then connect them again. 9 Start playback on the other Bluetooth device. o Confirm that the volume is turned up on the other Bluetooth device. If you do not turn up the volume on the playback device, no sound might be output from this unit. 10 Turn this unit's VOLUME knob to adjust the volume. o You can also use the VOLUME buttons on the remote control. o Depending on the connected Bluetooth device, you might not be able to adjust the volume. For details, refer to the operation manual of that Bluetooth device. Muting playback If you want to temporarily mute the volume of this unit, press the MUTE button on the remote control. Press the MUTE button on the remote control again to return to the previous volume level. Putting the unit into standby mode Press the standby/on () button on this unit or the remote con-

trol to put the unit into standby. Then, turn off the other Bluetooth device. 21 EN Settings 1 Press the MENU button to show the setting items. 3 Press the INPUT SELECTOR knob to confirm the selection. o You can also press the ENTER button on the remote control. o The currently set value is shown on the display. 4 Turn the INPUT SELECTOR knob to change the set-

ting value. o You can also use the up and down (k, j) buttons on the remote control. o Press the MENU button to return to setting item selection. 5 When you are done changing settings, press the MENU button to show the input source status again. o If you do not do anything for about 10 seconds, the display will return to showing the input source status. 2 Turn the INPUT SELECTOR knob to show the setting to be changed. o You can also use the up and down (k, j) buttons on the remote control. The menu items appear in the following order. UPCONVERT PCM D-FILTER DSD D-FILTER CLOCK SYNC LINE OUT LINE OUT LEVEL DIMMER AUTO POWER SAVE NETWORK SETUP*

*Shown only when the input source is NET/USBf 22 Upconversion Use to activate the upconversion circuit when receiving PCM format signals. o See page 13 for the relationships between input sampling fre-

quencies and sampling frequencies after upconversion. DSD digital filter Use to set the digital filter when receiving DSD format signals.

*DSD D-FILTER

> CUTOFF 50kHz

*UPCONVERT

> OFF OFF The original input signal is sent directly to the D/A converter without upconversion. 2Fs If the input audio signal is less than 2 a standard sampling fre-

quency, it is upconverted 2 and then sent to the D/A converter. 4Fs If the input audio signal is less than 4 a standard sampling fre-

quency, it is upconverted 4 and then sent to the D/A converter. 8Fs If the input audio signal is less than 8 a standard sampling fre-

quency, it is upconverted 8 and then sent to the D/A converter. DSD The input source is converted to DSD digital format, and then sent to the D/A converter. CUTOFF 50kHz 50kHz cutoff frequency CUTOFF 150kHz 150kHz cutoff frequency Clock sync o Clock sync is only possible when the input source is USB (rear USB port), NET or USBf (front USB port).

*CLOCK SYNC

> OFF OFF No clock sync is used. ON This unit's master clock will be synchronized to the 10MHz clock input through the clock sync input (10MHz IN) connector. PCM digital filter Use to set the digital filter when receiving PCM format signals. Line output

*PCM D-FILTER

> OFF

*LINE OUT

> RCA OFF The digital filter is disabled. FIR SHARP Use to select the connectors that output analog audio. o Output through both the RCA connectors and the XLR connec-

tors at the same time is not possible. An FIR filter with a steep roll-off is used to sharply cut signals out-

side the audio band. RCA Output through the RCA connectors. XLR2 Output through the XLR connectors with 2: HOT polarity. XLR3 Output through the XLR connectors with 3: HOT polarity. FIR SLOW An FIR filter with a slow roll-off is used to gently cut signals out-

side the audio band. SDLY SHARP A short delay filter with a steep roll-off is used to sharply cut sig-

nals outside the audio band. SDLY SLOW A short delay filter with a slow roll-off is used to gently cut signals outside the audio band. o When receiving signals at 352.8 kHz or 384 kHz, the digital filter will be disabled during playback regardless of this setting. 23 EN Settings (continued) Line output level

*LINE OUT LEVEL

> FIX 0dB Automatic power saving function This unit has an automatic power saving function. o The automatic power saving function is on when the unit is shipped new from the factory. Use to select audio level output from the analog audio output con-

nectors (LINE OUT).

*AUTO POWER SAVE

> ON OFF The automatic power saving function is disabled. ON If no input signal is locked for about 30 minutes, the unit will automatically enter standby mode. FIX 0dB A maximum of 2 Vrms is output. Select this if you want to adjust the volume using an amplifier. o No sound will be output if headphones are connected. FIX +6dB A maximum of 4 Vrms is output. Select this if you want to adjust the volume using an amplifier. o No sound will be output if headphones are connected. o If the sound distorts, set this to FIX 0dB. VARIABLE This will enable adjustment of the analog output level using the VOLUME knob. Select this if you want to adjust the volume using this unit. o No sound will be output if headphones are connected. OFF No sound is ever output. Display brightness

*DIMMER

> DIMMER 3 DIMMER 3 Ordinary brightness DIMMER 2 Slightly dim DIMMER 1 Even dimmer OFF Display off o The display stays unlit even when the unit is on. 24 Network setup To use network services, make network settings on this unit in advance. Make the settings according to the characteristics of the network to which it is being connected. o An Internet connection is necessary to use Internet radio, DLNA and other network services. o The "NET STANDBY" setting is not necessary for connecting this unit to a network. ATTENTION o If DHCP is set to ENABLE (default), "IP ADDRESS", "SUBNET MASK",

"GATEWAY" and "DNS SERVER" settings will appear, but cannot be changed. If DHCP is set to Disable, "IP ADDRESS", "SUBNET MASK",

"GATEWAY" and "DNS SERVER" will appear and must be set. o When you press the MENU button when viewing the "NETWORK SEUP" submenu, "NETWORK SETTING SAVE?" will appear. After changing a setting, press the ENTER button to save it. If you close a menu screen without pressing the ENTER button, setting changes will not be applied. The submenus appear in the following order. IP ADDRESS View/set the IP address. MAC ADDRESS View this unit's MAC address. DHCP ENABLE (default setting) DHCP is enabled. DISABLE DHCP is disabled. SUBNET MASK View/set the subnet mask. GATEWAY View/set the default gateway. DNS SERVER View/set the DNS server address. PROXY URL Set the proxy server address. PROXY PORT Set the proxy port number. o This only appears when a proxy URL has been set. NET STANDBY This sets whether or not the unit can be controlled over a net-

work when the unit is in standby. DISABLE (default setting) When the unit is in standby, it cannot be controlled over a network. ENABLE When the unit is in standby, it can be controlled over a network. o When set to "ENABLE", more power will be consumed when the unit is in standby. Inputting numbers Follow the procedures below to input IP addresses and other numbers. 1 When the input screen is open, press the INPUT SELECTOR knob.

*IP ADDRESS

>255 255 255 255 The number to the right of the > will be changed. o You can also press the ENTER button on the remote control. 2 Turn the INPUT SELECTOR knob to select the value.

*IP ADDRESS

>192 255 255 255 3 Press the INPUT SELECTOR knob to select the next digit for input.

*IP ADDRESS 192>255 255 255 After inputting all the digits, press the INPUT SELECTOR knob to complete input and return to the original screen. 25 EN Update You can update the firmware of this unit. Do not put the unit in standby during an update. o See the document included with the firmware for update procedures. CURRENT F/W Ver This shows the current firmware version. F/W UPDATE via USBf You can update the firmware using a USB flash drive. Settings (continued) Inputting characters Follow the procedures below to input characters for a PROXY server address. 1 When the input screen is open, press the INPUT SELECTOR knob.

*PROXY URL

>_ The character to the right of the > will be changed. o You can also press the ENTER button on the remote control. 2 Turn the INPUT SELECTOR knob to select a charac-

ter, and press the INPUT SELECTOR knob to input that character.

*PROXY URL

>

Turn the INPUT SELECTOR knob to show the icons below, fol-

lowed by ASCII characters in character code order.

: Enter Confirm an input character

: Insert Insert a character at the cursor position

: Delete Delete the character to the left of the cursor

: Back Move the cursor one character to the left

: Forward Move the cursor one character to the right 3 When done inputting characters, select the icon and the press the INPUT SELECTOR knob to confirm. 26 Playing back music on a computer Installing the driver on a computer This unit can be connected with computers running the following operating systems. Operation with other operating systems is not guaranteed. (As of January, 2015) About the transmission mode This unit connects using high-speed asynchronous mode. The sampling frequencies that can be transmitted are 32, 44.1, 48, 88.2, 96, 176.4, 192, 352.8 and 384 kHz. When properly connected, you will be able to select TEAC USB AUDIO DEVICE as an audio output from the computer OS. o In asynchronous mode, the audio data sent from the computer will be processed using this unit's clock, enabling the amount of jitter that occurs during data transmission to be reduced. Downloading playback application TEAC HR Audio Player You can download Mac and Windows versions of our free TEAC HR Audio Player application that supports playback of DSD files from the TEAC Global Site (http://teac-global.com/). TEAC HR Audio Player setting note To play 11.2MHz DSD recordings with TEAC HR Audio Player, open the Configure window and set the Decode mode to DSD Native. To play formats other than 11.2MHz DSD, you can set this to either DSD over PCM or DSD Native as you like. For details, see Selecting DSD decoding mode in the TEAC HR Audio Player Owners Manual. When using Mac OS The driver works with the following versions. OS X Lion (10.7) OS X Mountain Lion (10.8) OS X Mavericks (10.9) OS X Yosemite (10.10) This unit will run with the standard OS driver, so there is no need to install a special driver. When using Windows The driver works with the following versions. Windows 7 (32/64-bit) Windows 8 (32/64-bit) Windows 8.1 (32/64-bit) Installing the driver on the computer In order to play audio files stored on a computer through this unit, you must install a dedicated driver on that computer beforehand. Download the dedicated driver from the TEAC Global Site:

TEAC Global Site http://teac-global.com/

ATTENTION Install the dedicated driver before connecting the unit with the computer by USB. If you connect this unit with a computer before installing the driver, it will not work properly. o For instructions about driver installation procedures, access the Downloads page from the TEAC Global site (http://teac-global. com/). o Depending on the combination of hardware and software, proper operation might not be possible even with the above operating systems. 27 EN Playing back music on a computer (continued) Playing back audio files from a computer 5 Start playback of an audio file on the computer. 1 Connect the USB port on the rear of this unit to the computer using a USB cable. USB cable o Use a cable with a connector that matches that of this unit. 2 Turn the computer on. o Confirm that the operating system has started properly. 3 Shift the POWER switch to its ON position to turn the unit on. By maximizing the output volume from the computer and adjusting the volume output from the stereo amplifier, better sound quality can be achieved. Minimize the stereo amplifier volume before beginning play-

back. Then, gradually increase it. When using headphones connected to this unit, turn the VOLUME knob counterclockwise to minimize the volume before putting them on. Then, gradually increase it. o The computer and this unit cannot control each other. o Do not do any of the following when playing back an audio file via USB. Doing so could cause the computer to malfunction. Always quit the audio playback software before doing any of the following.

- Unplugging the USB cable

- Turning this unit off

- Changing the current input selection o When playing back an audio file via USB, computer operation sounds will also be output. If you do not want these sounds to be output, make appropriate settings on the computer to turn them off. o If you connect this unit with the computer or change its input to USB after starting the audio playback software, audio files might not play back correctly. If this should occur, restart the audio playback software or restart the computer. 4 Turn the INPUT SELECTOR knob to select USB. 28 If you experience a problem with the unit, please take a moment to review the following information before requesting service. If it still does not operate correctly, contact the retailer where you pur-

chased the unit. General The unit does not turn on. e Check that the power cord is completely plugged into the power outlet. If the outlet is switched, confirm that the switch is in the ON position. e Connect a different electrical device to the outlet to confirm that it is supplying power. e If the automatic power saving function has caused the unit to enter standby, press the remote control STANDBY/ON button to turn the unit on again. No sound is output. e If a stereo amplifier is connected to this unit, adjust its volume. e If you are using headphones connected to this unit, use the VOLUME knob to adjust the volume. e Use the INPUT SELECTOR knob to select the input that is con-

nected to the source that you want to hear. e Reconfirm the connections with other equipment. There is a humming noise. e If a connecting cable is near a power cord, fluorescent light or similar cause of interference, increase the distance between them as much as possible. There is no sound from one side of the headphones. e Confirm that the headphones plug is inserted completely. Clock sync The CLOCK indicator does not stop blinking. e Set clock synchronization to OFF when not using it. e Synchronization with the clock signal being input might not be possible. Check the connections of the clock sync connec-

tors and the settings of the connected device. Troubleshooting Connections with a computer Computer does not recognize this unit. e This unit can be connected with computers running the fol-

lowing operating systems. Operation with other operating systems is not guaranteed. (As of January, 2015) Mac OS OS X Lion (10.7) OS X Mountain Lion (10.8) OS X Mavericks (10.9) OS X Yosemite (10.10) o This unit can be used with the standard OS driver. Windows Windows 7 (32/64-bit) Windows 8 (32/64-bit) Windows 8.1 (32/64-bit) o Requires installation of a dedicated driver (page 27). Noise occurs. e Starting other applications during playback of a music file may interrupt playback or cause noise. Do not start other applications during playback. When the unit is connected to a computer via a USB hub, for example, noise might be heard. If this occurs, connect the unit directly to the computer. Audio files cannot be played back. e Connect this unit to the computer, and set this units input to USB before launching music playback software. If you connect this unit to the computer or set its input to USB after launching audio playback software, music files might not play back properly. Audio files Playback is not possible. e Check the file format. See Audio files playable by this unit on page 8. 29 EN Troubleshooting (continued) Internet radio Cannot connect to the Internet. e Confirm that a computer can connect to the Internet using the same network. e Enter a correct network connection password. e Check the settings of the networks firewall. e Confirm that the radio station is currently sending a signal. e Confirm that the address for the station has not changed. e The number of registered users for the station might have already reached a limit, making it unavailable to the public. e If the Internet connection speed is too slow, searching might take time. Restoring default settings While pressing and holding the MENU button, set the POWER switch to ON. Since this unit uses a microcontroller, external noise and other inter-

ference can cause the unit to malfunction. If this occurs, unplug the power cord, wait for a while, and then turn the unit on again and restart operations. o Release the MENU button when the SETUP CLEAR message appears. The factory default settings are the setting values shown in the screen images used in the explanations in this manual. 30 Analog audio outputs Connectors . XLR connectors 1 pair RCA connectors 1 pair Output impedance . XLR: 188 RCA: 150 Maximum output level (1 kHz/full-scale, into 10 k) FIX 0dB . XLR/RCA: 2.0 Vrms FIX +6dB . XLR/RCA: 4.0 Vrms Variable . XLR: 12 Vrms RCA: 6 Vrms Frequency response . 5 Hz 80 kHz (+1 dB/3 dB) S/N ratio . 110 dB (A-Weight, 1 kHz) Distortion . 0.0015% (1 kHz, LPF: 20 Hz 20 kHz) Headphones output Connector . Standard 6.3mm (1/4") stereo jack 1 Effective maximum output . 500 mW + 500 mW (into 32 ) Compatible impedance range . 16600 Digital audio inputs*

COAXIAL digital . RCA connector 1 3.5mm mini jack 1

(3.5mm mini plug connection also possible using RCA-mini plug adapter cable)

(0.5 Vp-p, 75 ) OPTICAL digital . Rectangular connector 1 3.5mm mini jack** 1

(24.0 to 14.5 dBm peak) USB flash drive . USB Type A port (front) 1

(USB 2.0 compliant) USB . USB Type B port (rear) 1

(USB 2.0 compliant) LAN . 100BASE-T PCM data sampling frequency COAXIAL digital 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz OPTICAL digital 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz USB . 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz, 352.8 kHz, 384 kHz Specifications Quantization bit depth COAXIAL digital/OPTICAL digital . 16/24-bit USB . 16/24/32-bit DSD data sampling frequency COAXIAL digital/OPTICAL digital . 2.8 MHz

(supported using 176.4kHz/24-bit DoP transmission) USB . 2.8 MHz, 5.6 MHz, 11.2 MHz

* See USB flash drives and Networks on page 8 for details about USB flash drives and networks,

** This input connector can be used for both optical and coaxial connections. Clock sync input Connector . BNC Input sampling frequency . 10 MHz Input impedance . 50 Input level . Rectangle wave: equivalent to TTL levels Sine wave: 0.5 to 1.0 Vrms General Power supply Model for Europe . AC 220240 V, 50/60 Hz Model for U.S.A./Canada . AC 120 V, 60 Hz Power consumption . 18 W Standby power . 0.4 W (in standby mode) 3 W (in network standby mode) External dimensions . 290 mm 81.2 mm 248.7 mm

(11 1/2 3 1/4 9 7/8)

(W H D including protrusions) Weight . 3.9 kg (8 5/8 lb) Operating temperature range . +5C to +35C Operating humidity range . 5 to 85% (no condensation) Storage temperature range . 20C to +55C Included accessories Power cord 1 RCA conversion (RCA to mini plug) cable 1 Remote control (RC-1320) 1 Batteries for remote control (AAA) 2 Owners manual (this document) 1 Warranty card 1 (for users in the USA and Canada only) o Design and specifications are subject to change without notice. Weight and dimensions are approximate. o Illustrations in this manual might differ slightly from production models. 31 EN INSTRUCTIONS DE SCURIT IMPORTANTES Lisez ces instructions. 1) 2) Conservez ces instructions. 3) Tenez compte de tous les avertissements. 4) Suivez toutes les instructions. 5) N'utilisez pas cet appareil avec de l'eau proximit. 6) Ne nettoyez l'appareil qu'avec un chiffon sec. 7) Ne bloquez aucune ouverture de ventilation. Installez-le confor-

mment aux instructions du fabricant. 8) N'installez pas l'appareil prs de sources de chaleur telles que des radiateurs, bouches de chauffage, poles ou autres appa-

reils (y compris des amplificateurs) dgageant de la chaleur. 9) Ne neutralisez pas la fonction de scurit de la fiche polarise ou de terre. Une fiche polarise a deux broches, l'une plus large que l'autre. Une fiche de terre a deux broches identiques et une troisime broche pour la mise la terre. La broche plus large ou la troisime broche servent votre scurit. Si la fiche fournie n'entre pas dans votre prise, consultez un lectricien pour le remplacement de la prise obsolte. 10) vitez de marcher sur le cordon d'alimentation et de le pincer, en particulier au niveau des fiches, des prises secteur, et du point de sortie de l'appareil. 11) N'utilisez que des fixations/accessoires spcifis par le fabricant. 12) Utilisez-le uniquement avec des chariots, socles, trpieds, supports ou tables sp-

cifis par le fabricant ou vendus avec l'appareil. Si un chariot est utilis, faites attention ne pas tre bless par un renversement lors du dplacement de l'ensemble chariot/appareil. 13) Dbranchez cet appareil en cas d'orage ou de non utilisation prolonge. 14) 14 Confiez toute rparation des techniciens de mainte-

nance qualifis. Une rparation est ncessaire si l'appareil a t endommag d'une quelconque faon, par exemple si le cor-

don ou la fiche d'alimentation est endommag, si du liquide a t renvers sur l'appareil ou si des objets sont tombs dedans, si l'appareil a t expos la pluie ou l'humidit, s'il ne fonc-

tionne pas normalement, ou s'il est tomb. o Lappareil tire un courant nominal de veille de la prise secteur quand son interrupteur POWER ou STANDBY/ON nest pas en position ON. o La fiche secteur est utilise comme dispositif de dconnexion et doit donc toujours rester disponible. o Des prcautions doivent tre prises en cas d'utilisation d'cou-

teurs ou d'un casque avec le produit car une pression sonore excessive (volume trop fort) dans les couteurs ou dans le casque peut causer une perte auditive. AT TENTION

: POUR RDUIRE LE RISQUE D'LECTROCUTION, NE RETIREZ PAS LE CAPOT (OU L'ARRIRE). AUCUNE PICE INTERNE N'EST RPARABLE PAR L'UTILISATEUR. CONFIEZ TOUTE RPARATION UN SERVICE APRS-VENTE QUALIFI.

< Le symbole d'clair tte de flche dans un triangle quilatral sert prvenir l'utilisateur de la prsence dans l'enceinte du produit d'une tension dangereuse non isole d'une grandeur suffisante pour constituer un risque d'lectrocution pour les personnes. B Le point d'exclamation dans un triangle quila-

tral sert prvenir l'utilisateur de la prsence d'instructions importantes de fonctionnement et de maintenance (entretien) dans les documents accom-

pagnant l'appareil. AVERTISSEMENT: POUR PRVENIR LES RISQUES D'INCENDIE ET D'LECTROCUTION, N'EXPOSEZ PAS CET APPAREIL LA PLUIE NI L'HUMIDIT. ATTENTION o NE RETIREZ PAS LES CAPOTS EXTERNES OU BOTIERS POUR EXPOSER L'LECTRONIQUE. AUCUNE PICE INTERNE N'EST RPARABLE PAR L'UTILISATEUR. o SI VOUS RENCONTREZ DES PROBLMES AVEC CE PRODUIT, CONTACTEZ LE MAGASIN O VOUS AVEZ ACHET L'UNIT. N'UTILISEZ PAS LE PRODUIT TANT QU'IL N'A PAS T RPAR. o L'UTILISATION DE COMMANDES, DE RGLAGES OU LE SUIVI DE PROCDURES AUTRES QUE CE QUI EST DCRIT DANS CE DOCUMENT PEUT PROVOQUER UNE EXPOSITION UN RAYONNEMENT DANGEREUX. 32 ATTENTION Pour les consommateurs europens Mise au rebut des quipements lectriques et lec-

troniques et des piles et/ou accumulateurs

(a) Tout quipement lectrique/lectronique et pile/accumula-

teur hors d'usage doit tre trait sparment de la collecte municipale d'ordures mnagres dans des points de collecte dsigns par le gouvernement ou les autorits locales.

(b) En vous dbarrassant correctement des quipements lec-

triques/lectroniques et piles/accumulateurs hors d'usage, vous contribuerez la sauvegarde de prcieuses ressources et la prvention de potentiels effets ngatifs sur la sant humaine et l'environnement.

(c) Le traitement incorrect des quipements lectriques/lectro-

niques et piles/accumulateurs hors d'usage peut avoir des effets graves sur l'environnement et la sant humaine en rai-

son de la prsence de substances dangereuses dans les quipements.

(d) Le symbole de dchets d'quipements lectriques et lectroniques (DEEE), qui reprsente une poubelle roulettes barre d'une croix, indique que les quipe-

ments lectriques/lectroniques et piles/

accumulateurs doivent tre collects et traits spar-

ment des dchets mnagers. Si une pile ou un accumulateur contient plus que les valeurs de plomb (Pb), mercure (Hg) et/ou cad-

mium (Cd) spcifies dans la directive sur les piles et accumulateurs (2006/66/CE), alors les symboles chimiques de ces lments seront indiqus sous le symbole DEEE. Pb, Hg, Cd

(e) Des systmes de retour et de collecte sont disponibles pour l'utilisateur final. Pour des informations plus dtailles sur la mise au rebut des vieux quipements lectriques/

lectroniques et piles/accumulateurs hors d'usage, veuillez contacter votre mairie, le service d'ordures mnagres ou le magasin dans lequel vous avez acquis l'quipement. DCLARATION DE CONFORMIT Nous, TEAC AUDIO EUROPE, Liegnitzer Strae 6, 82194 Grbenzell, Allemagne, dclarons sous notre propre responsabilit que le produit TEAC dcrit dans ce mode demploi est conforme aux normes techniques lui correspondant. o N'exposez pas cet appareil aux gouttes ni aux claboussures. o Ne placez pas d'objet rempli de liquide sur l'appareil, comme par exemple un vase. o Ninstallez pas cet appareil dans un espace confin comme une bibliothque ou un meuble similaire. o Lappareil doit tre plac suffisamment prs de la prise de courant pour que vous puissiez tout moment attraper facile-

ment la fiche du cordon d'alimentation. o Si le produit utilise des piles/batteries (y compris un pack de batteries ou des piles installes), elles ne doivent pas tre exposes au soleil, au feu ou une chaleur excessive. o PRCAUTION pour les produits qui utilisent des batteries rem-

plaables au lithium: remplacer une batterie par un modle incorrect entrane un risque d'explosion. Remplacez-les uni-

quement par un type identique ou quivalent. AVERTISSEMENT Les produits ayant une construction de Classe ! sont quips d'un cordon d'alimentation avec une fiche de terre. Le cordon d'un tel produit doit tre branch dans une prise secteur avec terre de scurit. AUX USA/CANADA, UTILISEZ UNIQUEMENT UNE TENSION D'ALIMENTATION DE 120 V. V Prcautions concernant les piles Un mauvais emploi des piles peut entraner leur rupture ou leur fuite, avec pour consquence un incendie, des blessures ou la salissure des objets proches. Veuillez lire et suivre attentivement les prcautions suivantes. o Veillez insrer les piles avec leurs ples positif () et ngatif

(^) correctement orients. o Utilisez des piles du mme type. Nutilisez jamais des types de pile diffrents ensemble. o Si la tlcommande doit rester inutilise durant une priode prolonge (plus dun mois), retirez ses piles pour viter quelles ne coulent. o Si les piles coulent, essuyez le liquide dans le compartiment des piles et remplacez les piles par des neuves. o N'utilisez pas de piles d'un type autre que celui spcifi. Ne mlangez pas des piles neuves avec des anciennes et nutilisez pas ensemble des types de pile diffrents. o Ne chauffez pas et ne dmontez pas les piles. Ne jetez jamais les piles dans un feu ou dans de leau. o Ne conservez et ne transportez pas les piles avec dautres objets mtalliques. Les piles pourraient entrer en court-circuit, couler ou exploser. o Ne rechargez jamais une batterie sans avoir vrifi quelle peut ltre. 33 FR Prcautions pour les quipements sans fil Conformit de l'metteur radio et brouillage Modle pour le Canada Conformit de l'metteur radio Ce dispositif est conforme la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionne-

ment est sujet aux deux conditions suivantes:

1) Le dispositif ne doit pas produire de brouillage prjudiciable, et 2) Ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. tiquetage d'autorisation IC: 1559C-NT503 Conformit de brouillage CET APPAREIL NUMRIQUE DE LA CLASSE B EST CONFORME LA NORME NMB-003 DU CANADA Modle pour l'EEE

(Espace conomique Europen) Cet quipement est conforme aux normes harmonises de la Directive 1999/5/CE (R&TTE). tiquetage de conformit Marquage CE:

ATTENTION L'autorisation des dispositifs sans fil varie avec les pays ou rgions. Veuillez n'utiliser cet appareil que dans le pays o il a t achet. o Selon le pays, des restrictions d'usage de la technologie sans fil Bluetooth peuvent exister. Vrifiez avant utilisation les lois et rglementations en vigueur dans le pays ou la rgion dans lequel vous voulez employer l'unit. Exigences pour l'exposition aux rayonnements Cet quipement est conforme la rglementation reconnue inter-

nationalement en matire d'exposition humaine aux ondes radio gnres par l'metteur. Dclaration de conformit Modle pour le Canada Cet quipement est conforme avec les limites d'exposition aux radiofrquences tablies pour un environnement non contrl par le CNR-102 de l'IC. Modle pour l'EEE

(Espace conomique Europen) Cet quipement est conforme la norme EN.62311: valuation des quipements lectroniques et lectriques en relation avec les res-

trictions d'exposition humaine aux champs lectromagntiques; la norme harmonise de la Directive 1999/5/CE. ATTENTION Les changements ou modifications non expressment approu-

vs par la partie responsable de la conformit peuvent invalider le droit de l'utilisateur faire fonctionner l'quipement. La plaque signaltique se trouve sous l'unit comme repr-

sent ci-dessous. Faade Plaque signaltique 34 Trademarks and other legal statement MPEG Layer-3 audio coding technology licensed from Fraunhofer IS and Thomson. Listening to SiriusXM Internet Radio

"DSD" is a registered trademark. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by TEAC CORPORATION is under license. 2013 CSR plc and its group companies. The aptX mark and the aptX logo are trade marks of CSR plc or one of its group companies and may be registered in one or more jurisdictions. This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft. Windows and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Mac, Mac OS and OS X are trademarks of Apple Inc., registered in the U.S. and other countries. IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license. Android is a trademark of Google Inc. DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks, service marks, or certification marks of the Digital Living Network Alliance. To listen to SiriusXM Internet Radio, youll need to subscribe to SiriusXM Internet Radio service and obtain a username and password. SiriusXM Internet Radio is available to residents of the United States and Canada. SiriusXM Internet Radio delivers a variety of commercial-free music including Pop, Rock, Country, R&B, Hip-Hop, Jazz, Classical and much more, plus expert sports talk and analysis. You also get exclusive entertainment, talk, comedy, family programming, local traffic and weather and news from your most trusted sources. Once youve purchased a SiriusXM Internet Radio compatible tuner youll need to subscribe to the service to listen to SiriusXM Internet Radio. There are a variety of programming packages available, including the option of adding The Best of XM pro-

gramming to the SiriusXM Internet Radio service. The Best of XM service is not available to Sirius Canada subscribers at this time. Please check with Sirius Canada for any updates using the num-

bers and web address below. Family friendly packages are also available to restrict channels that feature mature programming. To subscribe to SiriusXM Internet Radio, U.S. customers should visit www.sirius.com or call 1-888-539-SIRI (1-888-539-7474). Canadian customers should visit www.siriuscanada.ca. Current XM Radio Online subscribers will need to log into the XM online account manager and update their password in order for their credentials to work on a SiriusXM Internet Radio compat-

ible device. If the username is over 20 characters or their device doesnt support the @ character in the username, subscribers need to update the username on the same screen. Les autres noms de socit et de produit cits dans ce document sont des marques commerciales ou dposes de leurs dtenteurs respectifs. Information about copyrights and licensing related to open-source software is provided in the separate Important Notice Regarding Software document. 35 FR INSTRUCCIONES IMPORTANTES DE SEGURIDAD Lea estas instrucciones. 1) 2) Conserve estas instrucciones. 3) Cumpla con lo indicado en los avisos. 4) Siga todas las instrucciones. 5) No utilice este aparato cerca del agua. 6) 7) No bloquee ninguna de las ranuras de ventilacin. Instale este Lmpielo solo con un trapo seco. aparato de acuerdo con las instrucciones del fabricante. 8) No instale este aparato cerca de fuentes de calor como radia-

dores, calentadores, hornos u otros aparatos (incluyendo amplificadores) que produzcan calor. 9) No elimine el sistema de seguridad que supone el enchufe polarizado o con toma de tierra. Un enchufe polarizado tiene dos bornes, uno ms ancho que el otro. Uno con toma de tierra tiene dos bornes iguales y una tercera lmina para la conexin a tierra. El borne ancho o la lmina se incluyen para su segu-

ridad. Si el enchufe que venga con la unidad no encaja en su salida de corriente, haga que un electricista cambie su salida anticuada. 10) Evite que el cable de corriente quede de forma que pueda ser pisado o quedar retorcido o aplastado, especialmente en los enchufes, receptculos o en el punto en el que salen del aparato. 11) Use solo accesorios / complementos especificados por el fabricante. 12) Utilice este aparato solo con un soporte, trpode o bastidor especificado por el fabricante o que se venda con el propio aparato. Cuando utilice un bastidor con ruedas, tenga cuidado al mover la com-

binacin de aparato/bastidor para evitar que vuelque y puedan producirse daos. 13) Desconecte este aparato de la corriente durante las tormentas elctricas o cuando no lo vaya a usar durante un periodo de tiempo largo. 14) Dirija cualquier posible reparacin solo al servicio tcnico oficial. Este aparato deber ser reparado si se ha daado de alguna forma, como por ejemplo si el cable de corriente o el enchufe estn rotos, si ha sido derramado algn lquido sobre la unidad o algn objeto ha sido introducido en ella, si ha quedado expuesto a la lluvia o la humedad, si no funciona nor-

malmente o si ha cado al suelo en algn momento. o Este aparato libera corriente nominal no vlida para el fun-

cionamiento a travs de la toma de corriente, an cuando el interruptor de encendido y activacin (POWER o STANDBY/ON) no est en la posicin de encendido (ON). o El enchufe que se conecta a la red es el dispositivo de desco-

nexin, por lo que deber permanecer siempre en prefecto estado de uso. o Deber llevar cuidado si utiliza auriculares con este producto, ya que una excesiva presin sonora (volumen) procedente de los mismos puede causar perdidas de audicin. PRECAUCIN: PARA REDUCIR EL RIESGO DE DESCARGA ELCTRICA, NO QUITE LA CUBIERTA

(NI EL PANEL POSTERIOR). NO HAY PIEZAS INTERNAS QUE EL USUARIO PUEDA REPARAR. PARA REPARACIONES, REMTASE A UN SERVICIO TCNICO CUALIFICADO.

< El smbolo del rayo acabado en flecha dentro de un trin-

gulo equiltero alerta al usuario de la presencia de un voltaje peligroso sin aislar dentro de la carcasa del pro-

ducto que puede ser de magnitud suficiente como para constituir riesgo de descarga elctrica para las personas. B El signo de exclamacin dentro de un tringulo equi-

ltero alerta al usuario de la presencia de importantes instrucciones de funcionamiento y mantenimiento en la literatura que acompaa al aparato. ADVERTENCIA: PARA EVITAR RIESGO DE INCENDIO O DESCARGAS ELCTRICAS, NO EXPONGA ESTE APARATO A LA LLUVIA NI A LA HUMEDAD. PRECAUCIN o NO QUITE LAS CARCASAS EXTERNAS NI DEJE AL AIRE LA ELECTRNICA. EN EL INTERIOR NO HAY PIEZAS QUE EL USUARIO PUEDA MANIPULAR!

o SI EXPERIMENTA PROBLEMAS CON ESTE PRODUCTO, PNGASE EN CONTACTO CON EL ESTABLECIMIENTO DONDE ADQUIRI LA UNIDAD PARA SOLICITAR SERVICIO TCNICO. NO UTILICE EL APARATO HASTA QUE HAYA SIDO REPARADO. o EL USO DE CONTROLES, AJUSTES O PROCEDIMIENTOS QUE NO SEAN LOS ESPECIFICADOS EN ESTE MANUAL PUEDE CAUSAR EXPOSICIN A RADIACIONES PELIGROSAS. La placa de identificacin est situada en la parte inferior de la unidad como muestra la ilustracin. Frontal Placa de identificacin 36 PRECAUCIN Para consumidores europeos Deshacerse de aparatos elctricos, electrnicos, pilas/bateras y acumuladores a) Todos los aparatos elctricos y electrnicos, y pilas/bateras y acumuladores gastados, deben ser eliminados separados del resto de basura comn y nicamente en los puntos limpios o bajo los procedimientos especificados por el gobierno o autoridades municipales locales. b) Con la eliminacin correcta de los equipos elctricos y elec-

trnicos, y de pilas/bateras y acumuladores gastados, estar ayudando a conservar recursos muy valiosos y a evitar los posibles efectos negativos en la salud humana y en el medio ambiente. c) La eliminacin incorrecta de los equipos elctricos y electr-

nicos, y pilas/bateras y acumuladores, puede producir efectos muy dainos en el medio ambiente y en la salud humana a causa de las sustancias peligrosas que pueden encontrarse en estos equipos. d) El smbolo de Eliminacin de Aparatos Elctricos y Electrnicos (WEEE en ingls), identificado por cubos de basura con ruedas tachados, indican que los equi-

pos elctricos y electrnicos, y las pilas/bateras y acumuladores, deben ser eliminados de forma total-

mente independiente con respecto a la basura domstica. Si una pila/batera o un acumulador contienen ms cantidad de los valores especificados de plomo (Pb), mercurio (Hg), y/o cadmio (Cd) segn est definido en la Directiva relativa a las pilas (2006/66/EC), enton-

ces los smbolos qumicos correspondientes a estos elementos estarn indicados debajo del smbolo WEEE. Pb, Hg, Cd e) Existen sistemas para la eliminacin y recogida a disposicin del usuario final. Si necesita ms informacin sobre cmo deshacerse de aparatos elctricos y electrnicos antiguos, as como de pilas/bateras y acumuladores, pngase en contacto con su ayuntamiento, con la correspondiente empresa del servicio de recogida de residuos o con el establecimiento donde adquiri ese aparato. DECLARACIN DE CONFORMIDAD TEAC AUDIO EUROPE, Liegnitzer Strae 6, 82194 Grbenzell, Alemania, declara bajo su plena res-

ponsabilidad que el producto TEAC descrito en este manual cumple con las normas tcnicas correspondientes. o No exponga este aparato a salpicaduras ni goteras. o No coloque objetos que contengan lquidos, como por ejem-

plo jarrones, sobre el aparato. o No instale este aparato en lugares cerrados tales como estan-

teras o similares. o Este aparato debe situarse lo suficientemente cerca de una toma de electricidad como para poder alcanzar fcilmente el cable de corriente en cualquier momento. o Si el producto utiliza pilas (esto incluye las pilas instaladas y los packs de pilas), se evitar su exposicin directa al sol, al fuego o a cualquier otra fuente de calor excesivo. o PRECAUCIN con los productos que emplean bateras de litio reemplazables: existe peligro de explosin si la batera se reemplaza por otra de tipo incorrecto. Reemplcela slo por otra igual o de tipo equivalente. AVISO Los productos con construccin de Clase ! estn equipados con un cable de alimentacin que tiene conexin de tierra. El cable de estos productos deber conectarse a una toma de corriente que tenga conexin de proteccin de tierra. EN EE. UU./CANAD, UTILICE SOLO ALIMENTACIN CON CORRIENTE DE 120 V. V Precauciones con respecto a las pilas Un mal uso de las pilas puede hacer que se rompan o que ten-

gan fugas y ello causar fuego, lesiones u oxidacin en los objetos cercanos. Por favor, lea y observe las siguientes precauciones cuidadosamente. o Asegrese de introducir las pilas siempre con la correcta orienta-

cin de los polos positivo () y negativo (^). o Use pilas del mismo tipo. Nunca utilice juntas pilas de tipos diferentes. o Si no va a utilizar el mando a distancia durante mucho tiempo

(ms de un mes), quite las pilas para evitar que se sulfaten y ten-

gan fugas. o Si las pilas presentan fugas, limpie el lquido que haya cado en el compartimento y sustituya las pilas por otras nuevas. o No utilice pilas que no sean del tipo especificado. No mezcle pilas nuevas con viejas ni utilice juntas pilas de tipos distintos. o No caliente ni desarme las pilas. Nunca tire pilas al fuego ni al agua. o No transporte ni almacene pilas con otros objetos metlicos. Las pilas podran producir cortocircuitos, perder lquido o explotar. o Nunca recargue una pila si no est completamente seguro de que es una pila recargable. 37 ESPAOL Precauciones con los equipos inalmbricos Cumplimiento de las normas de interfe-

rencias y transmisin de radio Modelo para EE. UU. Declaracin de conformidad Parte responsable:

TEAC AMERICA, INC. Direccin: 1834 Gage Road, Montebello, California, U.S.A. Nmero de telfono: 1-323-726-0303 Este dispositivo cumple con el apartado 15 de las Normas de la FCC. Su funcionamiento est sujeto a las dos siguientes con-

diciones: (1) este dispositivo no puede causar interferencias perjudiciales y (2) este dispositivo debe aceptar cualquier inter-

ferencia recibida, incluyendo aquellas que puedan producir un funcionamiento no deseado. Etiquetado de autorizacin ID de la FCC: XEG-NT503 Requerimientos acerca de la exposicin a radiaciones Este equipo cumple con la regulacin internacionalmente reco-

nocida para los casos de exposicin humana a ondas de radio generadas por un transmisor. Declaracin de cumplimiento Modelo para EE. UU. Este equipo cumple con los lmites de exposicin a radiacin esta-

blecidos por la FCC para entornos no controlados y cumple las directrices de la FCC en materia de exposicin a radiofrecuencia. Modelo para el Espacio Econmico Europeo (EEE) Este equipo cumple con la valoracin EN.62311 de equipos electr-

nicos y elctricos relativa a las restricciones de exposicin humana a campos electromagnticos, el estndar armonizado de la DIRECTIVA 1999/5/EC. Modelo para el Espacio Econmico Europeo (EEE) Este equipo cumple con el estndar armonizado de la DIRECTIVA 1999/5/EC ( R&TTE ). Etiquetado de conformidad con la indicacin CE:

PRECAUCIN La autorizacin de dispositivos inalmbricos son diferentes segn los pases o regiones. Por favor, utilice el producto solamente en el pas donde lo adquiri. o Dependiendo del pas, podran existir restricciones para el uso de la tecnologa inalmbrica Bluetooth. Verifique las leyes y regulaciones del pas o regin donde vaya a uti-

lizar la unidad antes de hacerlo. 38 PRECAUCIN Cualquier cambio o modificacin efectuada en este equipo que no haya sido expresamente aprobada por la parte responsable del cumplimiento de los requisitos exigidos podra invalidar el derecho del usuario a utilizar el equipo.. Informacin sobre interferencias

(requerimientos de la FCC) Se ha comprobado que este equipo cumple con los lmites estable-

cidos para los dispositivos digitales de Clase B, de acuerdo con el apartado 15 de las Normas de la FCC. Estos lmites estn diseados para proporcionar una proteccin razonable contra interferencias perjudiciales en instalaciones residenciales. Este equipo genera, utiliza y puede irradiar energa de radiofrecuen-

cia y, si no se instala y se utiliza de acuerdo con las instrucciones, puede causar interferencias perjudiciales en las comunicaciones por radio. Sin embargo, no se puede garantizar que dichas interferencias no se produzcan en instalaciones particulares. Si este equipo causa interferencias perjudiciales en la recepcin de radio o televisin, que se comprueban apagando y encendiendo el equipo, se reco-

mienda al usuario que intente corregirla mediante una o varias de las siguientes medidas. o Reoriente o recoloque el equipo y/o la antena receptora. o Aumente la separacin entre el equipo y el receptor. o Conecte el equipo a una toma de electricidad situada en un cir-

cuito elctrico diferente al del receptor. o Consulte al distribuidor o solicite ayuda a un tcnico de radio/TV con experiencia. Trademarks and other legal statement MPEG Layer-3 audio coding technology licensed from Fraunhofer IS and Thomson. Listening to SiriusXM Internet Radio DSD is a registered trademark. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by TEAC CORPORATION is under license. 2013 CSR plc and its group companies. The aptX mark and the aptX logo are trade marks of CSR plc or one of its group companies and may be registered in one or more jurisdictions. This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft. Windows and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Mac, Mac OS and OS X are trademarks of Apple Inc., registered in the U.S. and other countries. IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license. Android is a trademark of Google Inc. DLNA, the DLNA Logo and DLNA CERTIFIED are trademarks, service marks, or certification marks of the Digital Living Network Alliance. To listen to SiriusXM Internet Radio, youll need to subscribe to SiriusXM Internet Radio service and obtain a username and password. SiriusXM Internet Radio is available to residents of the United States and Canada. SiriusXM Internet Radio delivers a variety of commercial-free music including Pop, Rock, Country, R&B, Hip-Hop, Jazz, Classical and much more, plus expert sports talk and analysis. You also get exclusive entertainment, talk, comedy, family programming, local traffic and weather and news from your most trusted sources. Once youve purchased a SiriusXM Internet Radio compatible tuner youll need to subscribe to the service to listen to SiriusXM Internet Radio. There are a variety of programming packages available, including the option of adding The Best of XM pro-

gramming to the SiriusXM Internet Radio service. The Best of XM service is not available to Sirius Canada subscribers at this time. Please check with Sirius Canada for any updates using the num-

bers and web address below. Family friendly packages are also available to restrict channels that feature mature programming. To subscribe to SiriusXM Internet Radio, U.S. customers should visit www.sirius.com or call 1-888-539-SIRI (1-888-539-7474). Canadian customers should visit www.siriuscanada.ca. Current XM Radio Online subscribers will need to log into the XM online account manager and update their password in order for their credentials to work on a SiriusXM Internet Radio compat-

ible device. If the username is over 20 characters or their device doesnt support the @ character in the username, subscribers need to update the username on the same screen. Los nombres de otras compaas y de productos que aparecen en este documento son marcas comerciales o registradas de sus res-

pectivos propietarios. Information about copyrights and licensing related to open-source software is provided in the separate Important Notice Regarding Software document. 39 ESPAOL WARRANTY/GARANTIE/GARANTA Europe/Europa This product is subject to the legal warranty regulations of the country of purchase. In case of a defect or a problem, please contact the dealer where you bought the product. Ce produit est sujet aux rglementations concernant la garantie lgale dans le pays dachat. En cas de dfaut ou de problme, veuillez contacter le revendeur chez qui vous avez achet le produit. Las condiciones de garanta de este aparato estn sujetas a las disposiciones legales sobre garanta del pas en el que ha sido adquirido. En caso de garanta, debe dirigirse al estable-

cimiento donde adquiri el aparato. In countries/regions other than the USA, Canada and Europe This warranty gives you specific legal rights, and you may also have other rights that vary by country, state or province. If you have a warranty claim or request, please contact the dealer where you bought the product. Z TEAC CORPORATION 1-47 Ochiai, Tama-shi, Tokyo 206-8530 Japan Phone: +81-42-356-9156 TEAC AMERICA, INC. 1834 Gage Road, Montebello, California 90640 U.S.A. Phone: +1-323-726-0303 TEAC AUDIO EUROPE Liegnitzer Strae 6, 82194 Grbenzell, Germany Phone: +49-8142-4208-141 This device has a serial number located on its rear panel. Please record the serial number and retain it for your records. Model name: NT-503 Serial number:

0515.MA-2153A