FCC ID: 2AZBO-N00026 Wireless Earphone

TRUE WIRELESS STEREO EARBUDS WITH CHARGING CASE UCCWS07 Thank you for purchasing an original Nautica True Wireless Stereo Earbuds With Charging Case - UCCWS07 You are getting a high-quality product thats built to combine technology and design for your everyday use. Please read the below info carefully to get the most out of your new product. SAFETY AND MAINTENANCE Before you use the device, read the following precautions carefully to ensure optimal product performance. The use of earbuds will impair your ability to hear other sounds. Use caution while using your earbuds during any activity that requires your full attention. This package contains small parts that may be hazardous to children and should be kept out of reach of children. This product is not a toy never allow children to play with this product. Please do not overuse the earbuds or put them under heavy pressure. Keep away from wet and heat. Exposing the product to extreme hot or cold, such as in a closed car in the summer and winter conditions, will reduce the capacity and lifetime of the product. Earbuds listening at high volume levels especially over extended periods of time may damage your hearing. 9 Keep away from router or other high-frequency transmitting equipment to prevent interruption of signal receiving. Please use the earbuds under working range (up to 33 ft / 10 m). The effective range may vary depending on multiple conditions. Power time may differ depending on personal use habits. Do not dismantle the product. If any parts of your product require replacement for any reason, including normal wear and tear or breakage, please contact us. Unauthorized parties may damage the product. Do not drop, strongly vibrate, or strike the product with hard objects to avoid damaging the internal circuit. Do not use drastic chemicals or cleaner to clean the product. Do not use sharp objects to scratch the product surface. 10 WHATS IN THE BOX WARRANTY INFORMATION TRUE WIRELESS STREREO EARBUDS CHARGING CASE TYPE-C TO USB-A CHARGING CABLE USERS MANUAL Your product comes with four pairs of eartips ( S, M and L ). Try all sizes to find the size that fits best. Your device comes with size M eartips on. 3 HOW TO USE ?

*Multi-function Button

*MFB (LEFT) Press and hold for 5 secs to POWER ON or OFF Double press:

Previous track Press once: Answer call Press once: End call Double press:

Reject call MFB (RIGHT) Press and hold for 5 secs to POWER ON or OFF Double press:

Next track Press once:

Answer call Press once: End call Double press:

Reject call We do our best to make sure that this product is free from defects in materials and workmanship for a period of 1 year. The following conditions must be met for your warranty claim to be approved:

You must have purchased the product from a Nautica or Technofashion authorized dealer. You must provide proof as to the date of purchase from the Nautica or Technofashion authorized dealer. You must have used the product only as intended and in accordance with the products care instructions. 11 Within 12 months after the purchase, in case the product is determined to be defective (at the date of original purchase) due to improper materials or workmanship, you are entitled to free repair or exchange of goods. The product should be returned to Technofashion. The warranty does not cover defects caused by third-party modifications, repairs or replacement parts. Punctures, scratches, normal wear and tear and the natural breakdown of colors and materials over extended time and use are not warranted. Warranty applies to the USA only. We will make every effort to replace limited edition or discontinued products but cannot guarantee availability for replacement.

*Multi-function Button 4 12 BLUETOOTH PAIRING 1. Press each MFB button for 5 seconds, to turn on both earbuds. No need to hold MFB button after power is on. The Left & Right will automatically connect, one of the two earbud LEDs flashes white and green alternately. 2. Find UCCWS07 to connect with your phone. CHARGING EARBUDS Charging: White LED light turns on Fully charged: White LED turns green for 30 seconds and then Green LED turns off CHARGING CASE Plug the small end of the USB cable into the Type-C USB port of the charging case. Plug the other end into a USB wall charger or computer (DC 5V) that is powered on. TECHNICAL SPECIFICATIONS Bluetooth Version v5.3 Play Time Earbuds Charging Time Up to 7 hours Up to 2 hours Charging Case Charging Time Up to 1 hours Standby Time 40 hours Battery Capacity (Each earbud) 25x2mAh Battery Capacity(charging case) 180mAh Speaker Drivers Wireless Range 0.50in/ 13mm Up to 33ft/ 10m Impedance 32 Frequency Response 20Hz-25kHz Sensitivity

-383db Rated Input Voltage 5V Earbud Dimensions 1.41x1.02x1.24in / 35.8x26x31.6 mm Charging Case Dimensions 2.28x2.28x0.87 in / 58x58x22 mm Weight (Each Earbud) 0.11 oz / 3.1 g Weight (Charging Case) 1.16 oz / 32.8g Charging Port Type-C Speaker Drivers Type Composite film 5 6 7 8 Any limited edition or discontinued product still under its applicable warranty that cannot be replaced with an identical product will be replaced with the equivalent model based on availability. We may make changes to products and designs in the time you purchased your product and submitted a warranty claim. Products repaired or replaced under this warranty may or may not incorporate these changes. 13 SUPPORT For any questions, email us at support@technofashion.com FCC ID: 2AZBO-N00026 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found complying with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. 14 However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the device and receiver. Connect the device into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. 15 designed, manufactured, distributed by Technofashion, Inc. All Rights Reserved. Designed in USA. Made in China.

Siete MM \ UNNYELUYYUTEUYAY AQUA wu OL 02 ere rapit cau 08 06 QOLOF Oz OF OV Oy 99 09 a4 Og os Oobop oF oF Oe Oe 0S 09 OL 08 0 fm Fradtuntiuatiuituattunhin vuulbvvnsnarlauabannhuuutbanshn

2.4GHz 3216 Chip Antenna: AAN3216F5P2G45 ______________________________________________________________________________________________________ Application:

WLAN, 802.11b/g, Bluetooth, etc Features SMD, high reliability, ultra Impact, Omni-directional Part number AAN 3216 - F5

(3)

(2) P 2G45

(4)

(5)

(1)

(1)Product Type Chip Antenna

(2)Size Code

(3)Type Code

(4)Packing

(5)Frequency 3.2x1.6mm F5 Paper Tape 2.45GHz Electrical Specification Working Frequency Range 2400 ~2484 MHz Peak Gain Impedance Return loss Polarization Azimuth Beamwidth Operation Temperature() The specification is defined on EVB. 1.6 dBi (Typ.) 50 Ohm 10 dB ( Min) Linear Omni-directional

-40 ~85 Dimension and Terminal Configuration Dimension (mm) No. Terminal Name L W T A 3.15+-0.15 1.55+-0.15 0.50+-0.10 0.35+-0.10 1 2 Feeding point GND 2.4GHz 3216 Chip Antenna: AAN3216F5P2G45 ______________________________________________________________________________________________________ Evaluation Board Reference PCB Dimension Antenna Layout Reference Electrical Characteristics Return Loss Return Loss & Radiation unit :mm Frequency

(MHz) 2400 2442 2484 S11 (dB)

-11.0

-20.2

-10.6 Radiation 2.4GHz 3216 Chip Antenna: AAN3216F5P2G45 ______________________________________________________________________________________________________ Taping Specifications Reel Specification Reel and Taping Specification TYPE SIZE A B C D W M 3216 7 3K/Reel 2.00.5 13.51.0 211.0 601.0 11.52.0 1782.0 Tapping Specification Packaging Type A B W E F G H T Paper Type 3216 1.900.20 3.500.20 8.00.20 1.750.10 3.50.05 4.00.10 2.00.05 0.750.10 D

+0.10 P 1.50

-0 4.00.1 2.4GHz 3216 Chip Antenna: AAN3216F5P2G45 ______________________________________________________________________________________________________ Reliability Table Test ItemProcedureRequirementsCeramic TypeRemark(Reference)ElectricalCharacterizationFulfill the electricalspecificationUser Spec.ThermalShock1.Preconditioning:50 10 / 1 hr , then keep for 24 1 hrs at room temp.2.Initial measure: Spec: refer Initial spec.3.Rapid change of temperature test:-30 to +85; 100 cycles;15 minutes at Lower category temperature;15 minutes at Upper category temperature.No Visible Damage.Fulfill the electricalspecification.MIL-STD-202107TemperatureCycling1.Initial measure: Spec: refer Initial spec.2.100 Cycles (-30 to +85), Soak Mode=1 (2 Cycle/hours).3.Measurement at 24 2Hours after test condition.No Visible Damage.Fulfill the electricalspecification.JESD22JA104High TemperatureExposure1.Initial measure: Spec: refer Initial spec.2.Unpowered; 500hours @ T=+85.3.Measurement at 24 2 hours after test.No Visible Damage.Fulfill the electricalspecification.MIL-STD-202108Low TemperatureStorage1.Initial measure: Spec: refer Initial spec.2.Unpowered: 500hours @ T= -30.3.Measurement at 24 2 hours after test.No Visible Damage.Fulfill the electricalspecification.MIL-STD-202108Solderability(SMD Bottom Side)Dipping method:a.Temperature: 235 5Cb.Dipping time: 3 0.5sThe solder should coverover 95% of the criticalarea of bottom side.IEC 60384-21/224.10Soldering HeatResistance(RSH)Preheating temperature: 150 10C.Preheating time: 1~2 min.Solder temperature: 260 5C.Dipping time: 5 0.5sNo Visible Damage.IEC 60384-21/224.10Vibration5g's for 20 min., 12 cycles each of 3 orientationsNote: Use 8"X5" PCB .031" thick 7 secure points on, one longside and 2 secure points at corners of opposite sides. Partsmounted within 2" from any secure point. Test from 10-2000Hz.No Visible Damage.MIL-STD-202Method 204MechanicalShockThree shocks in each direction shall be applied along the threemutually perpendicular axes of the test specimen (18 shocks)Peak value: 1,500gsDuration: 0.5msVelocity change: 15.4 ft/sWaveform: Half-sineNo Visible Damage.MIL-STD-202Method 213HumidityBias1.Humidity: 85% R.H., Temperature: 85 2 C.2.Time: 500 24 hours.3. Measurement at 24 2hrs after test condition.No Visible Damage.Fulfill the electricalspecification.MIL-STD-202Method 106 2.4GHz 3216 Chip Antenna: AAN3216F5P2G45 ______________________________________________________________________________________________________ Revision History Revision Date Content 1 2018/7/20 New issue BoardFlex(SMD)1.Mounting method:IR-Reflow. PCB Size (L:100 W:40 T:1.6mm)2.Apply the load in direction of the arrow until bending reaches2 mm.No Visible Damage.AEC-Q200005AdhesionForce of 1.8Kg for 60 seconds.No Visible DamageMagnification of 20X orgreater may be employedfor inspection of themechanical integrity of thedevice body terminals andbody/terminal junction.AEC-Q200006PhysicalDimensionAny applicable method using x10 magnification, micrometers,calipers, gauges, contour projectors, or other measuringequipment, capable of determining the actual specimendimensions.In accordance withspecification.JESD22JB100

Sep 01, 2023 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, I appoint Shenzhen Timeway Testing Laboratories/ Zone C, 1st Floor, Zone C, 1st Floor, Block B, Jun Xiang Da Building, Zhongshan Park Road West, Tong Le Village, Nanshan District, Shenzhen, China (Name of Agent company name and address) to act as our agent in the preparation of this application for equipment certification. I certify that submitted documents properly describe the device or system for which equipment certification is sought. I also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commissions regulations will have affixed to it a label identical to that submitted for approval with this application. For instances where our authorized agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with T E C H N O F A S H I O N I N C . / 26, Park Street Ste#2340, Montclair, NJ, USA, 07042

<Signature>

NameCOSKUNOGLU UGUR CESUR TitleManager Applicant CompanyTECHNOFASHION INC.

Sep 01, 2023 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AZBO-N00026 Product Name: Wireless Earphone Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

Schematics Block diagram Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors.

<Signature>

NameCOSKUNOGLU UGUR CESUR TitleManager Applicant CompanyTECHNOFASHION INC.

TECHNOFASHION INC. Statement We TECHNOFASHION INC. Hereby Declare that The product Wireless Earphone, models no. UCCWS07, UCCWS07-1, UCCWS07-2, UCCWS07-3, UCCWS07-4 are all identical in interior structure, electrical circuits and components, and just the model names and appearance color are different for the marketing requirement. Your assistance on this matter is highly appreciated. Yours sincerely, Signature:

Company Name: TECHNOFASHION INC.

TECHNOFASHION INC. Covered Equipment Certification Attestation Letter 9/1/2023 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: Reviewing Engineer FCC ID: 2AZBO-N00026 TECHNOFASHION INC. certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not covered equipment. TECHNOFASHION INC. (the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Signed:

Printed name: COSKUNOGLU UGUR CESUR Title: Manager Company Name: TECHNOFASHION INC. Date: 9/1/2023

TECHNOFASHION INC. U.S. Agent Designation for Service of Process -

Certification Attestation Letter 9/1/2023 TO: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 ATTN.: Reviewing Engineer FCC ID: 2AZBO-N00026 FRN of applicant: 0030696439 Per section 2.911(d)(7) of the FCC rules, TECHNOFASHION INC. certifies that the equipment for which authorization is sought is designated to the following U.S. agent* for service of process:

Company Name: TECHNOFASHION INC. FCC Registration Number (FRN): 0030696439 Physical U.S. Company Address: 26, Park Street Ste#2340, Montclair, NJ, 07042 USA Contact Person: COSKUNOGLU UGUR CESUR Agent Email Address: info@technofashion.com The above contact person accepts the obligation for service of process. The applicant accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant Signed:

Agent Signed (if different from Applicant):

Signed:

Printed name: COSKUNOGLU UGUR CESUR Title: Manager Company Name: TECHNOFASHION INC. Date: 9/1/2023 Signed:

Printed name: Click here to enter text. Title: Click here to enter text. Company Name: Click here to enter text. Date: Click here to enter a date.

* the applicant must designate a contact located in the United States for purposes of acting as the applicants agent for service of process, regardless of whether the applicant is a domestic or foreign entity. An applicant located in the United States may designate itself as the agent for service of process.