FCC ID: 2AFJA-LPV6 Smart Watch

The Wand Company Chronomark LPV6 Smart Watch Draft user manual v0.3

All presses are short press unless noted as long press.

- When performing a long press, the screen goes blank. Turn ON Top right button > ON - briey shows welcome screen before going to the main clock screen. Welcome Screen shows for about 1 second, then goes to main Clock Screen (see detailed description below)

The screen automatically turns off if the watch is not used for 20 seconds. A short press on any button turns the screen back on.

- When wearing the watch, tilting it towards you to view it automatically turns the screen on. Turn OFF Long press and hold the top right button (2 seconds) from the clock screen to turn the watch OFF. Note: screen goes dark, continue to hold until OFF screen options show. Then conrm (press the button next to the tick) or cancel (cross) to go back to the main screen.

A goodbye screen briey displays a parting message randomly picked from a number of different words or phrases either saying goodbye in different languages or a classic parting quote from some well-known sci- TV shows and lms. 1 The Wand Company Chronomark LPV6 Smart Watch draft user manual Main Clock Outer ring:

Inner ring:

Inner circle:

Analogue time and button function icons (for that screen). Steps as a percentage of users daily target. Icons for notications (not shown in the photo below).

- Day, time and date

- Grey line shows percentage battery remaining

Red/blue dot below battery line shows Bluetooth connection status

Button pressing Top right > notications Bottom right > changes clock display: time and step lite 1 > time and logo lite 2 long press and hold > Settings menu Bottom left > sunrise, sunset and moon phase information long press and hold > torch mode Top left > sensor data long press and hold > weather data 2 The Wand Company Chronomark LPV6 Smart Watch draft user manual Sunrise, sunset and moon phase Analogue time and button function icons (for that screen). Outer ring:

Inner ring:

Inner circle:

- Moon phase. Sunrise and sunset are shown as times and also as a percentage of the daylight hours, accurate for the date and the users location. Button pressing Top right > notications Bottom right > main clock screen Bottom left > sunrise, sunset and moon phase for the following day, press again for the next day etc. Top left > weather data

(note: if the bottom left button has been pressed and the screen is showing sun and moon information for a future day, the top left button goes back to the previous sun-moon screen.) 3 The Wand Company Chronomark LPV6 Smart Watch draft user manual Sensor data Outer ring:

Inner circle:

Analogue time and button function icons (for that screen).

- Watch sensor data barometric pressure x/y/z accelerometer data x/y/z magnetometer data

- watch temperature measurements. Notes:

Temperature measurement is very sensitive, showing changes as small as 0.01 Celsius, but its measuring the temperature inside the watch body (which is affected by the temperature of the display backlight, the battery and the electronics) so the measurements have a signicant offset from the ambient air temperature or the users wrist temperature. Barometric reading is very accurate and will measure and change with vertical movement of the watch

> etc. Button pressing Top right > notications Bottom right > main clock screen Bottom left > scrolls up through detail screens for each sensor Top left > scrolls down through detail screens for each sensor 4 The Wand Company Chronomark LPV6 Smart Watch draft user manual Weather data Outer ring:

Inner circle:

Notes:

Analogue time and button function icons (for that screen).

- Weather data with icons and graphed for today (day 0) and tomorrow (day +1).

Top right button toggles between:

- humidity / chance of precipitation, and

- atmospheric pressure / wind speed. The forecast will be updated from the phone app. The watch currently shows demo data if nothing has been pushed from the phone.

> day 12 > day 23 > etc. Top right > toggles between humidity/precipitation and pressure/wind speed Button pressing Bottom right > main clock screen Bottom left > next two days forecast Top left > back to moon phase (while viewing day 0 and day +1) while viewing future days, the top left button goes back to the previous days weather screen. 5 The Wand Company Chronomark LPV6 Smart Watch draft user manual Notications Outer ring:

Inner circle:

- Notications Analogue time and button function icons (for that screen). This screen will automatically pop up when a new notication is received Button pressing Top right > select notication to view > press again to delete the notication from watch Bottom right > return to list if viewing notication or return to main clock screen if viewing list Bottom left > scroll down list of notications Top left > scroll up list 6 The Wand Company Chronomark LPV6 Smart Watch draft user manual Torch mode Outer ring:

Inner circle:

Analogue time and button function icons (for that screen).

- White screen at full backlight brightness Button pressing Top right > exit Bottom right > exit Bottom left > exit Top left > exit 7 The Wand Company Chronomark LPV6 Smart Watch draft user manual Settings menu Outer ring:

Inner circle:

Settings menu Analogue time and button function icons (for that screen).

Button pressing Top right > select Bottom right > back Bottom left > scroll down Top left > scroll up FCC and ISED (Industry Canada) Regulatory Information The regulatory information e-label can be found in the About screen, which is accessed from the Settings menu. To read the e-label, while in the Main Clock screen:

Press and hold the bottom right button for about 3 seconds until the Settings menu appears. Click the bottom left button to move the selection bar down until About is highlighted. Click the top right button (to select About) to display the e-label. To return to the Main Clock screen, click the lower right button. Notes:

To force-reset the watch, long press the top and bottom right-hand buttons together for 10 seconds until small white text appears on the screen, then let go of the buttons. 8 The Wand Company Chronomark LPV6 Smart Watch draft user manual FCC Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. IC WARNING This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.

The Wand Company Ltd 3, Laundress Lane, Cambridge CB2 1SD, United Kingdom Date: 2021-12-14 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCCID: 2AFJA-LPV6 TO WHOM IT MAY CONCERN:

We, the undersigned, hereby declare that the e-label meets the following requirements:

1. The FCC ID can be found through the following steps a) Press and hold the bottom right button for about 3 seconds until the Settings menu appears. b) Click the bottom left button to move the selection bar down until About is highlighted. c) Click the top right button (to select About) to display the e-label. 2. The product does not require the use of special access codes or accessories (e.g. SIM/USIM cards) to access the FCC ID. 3. User Manual will show the FCC ID and direct the user where to find the FCC ID information, and the FCC ID is displayed electronically in a manner that is clearly legible without the aid of magnification. 4. The FCC ID information will not change for any reason, like system upgrades, etc. 5. A physical temporary label will be affixed to the product, which is a protective film on the back of the product, as shown on the right:

Best regards, The Wand Company Ltd Richard Blakesley/Manager

Reference No.: WTX21X11118945W-1 Page 1 of 11 ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format FCC ID: 2AFJA-LPV6 Specifications: Users must be able to access the regulatory information without requiring special access codes or permissions, and in all cases the information must be accessible in no more than three steps from a products main or home menu. Products must not require special accessories or supplemental plug-ins (e.g., the installation of a SIM/USIM card) to access the information. The FCC ID, or other information must be displayed electronically in a manner that is clearly legible without the aid of magnification. Both regulatory information and dedicated exclusive application(s) or script(s) must be secured and implemented in a factory-set-unalterable format. When e-labeling is used, a physical temporary label is also required on the product, or a label on the packaging, at the time of importation, marketing, and sales. The physical label can be a summary version of the required regulatory information, such that the product can be identified as complying with the FCCs equipment authorization requirements, etc. The way to view the e-Label: 1. Home; 2. Settings menu; 3. About. A physical temporary label will be affixed to the product, which is a protective film on the back of the product. Proposed Label Location on EUT FCC ID Label Location Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn

The Wand Company Ltd 3, Laundress Lane, Cambridge CB2 1SD, United Kingdom Date: 2021-11-23 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2AFJA-LPV6 Condentiality Request Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of the information accompanying this application as outlined below:

Tune-Up Information Security Information Software Defined Radio (SDR) Information The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. To whom it may concern, Block Diagram Operational Description Schematics Parts List Sincerely, The Wand Company Ltd Richard Blakesley / Manager

The Wand Company Ltd 3, Laundress Lane, Cambridge CB2 1SD, United Kingdom

(FCC ID2AFJA-LPV6) POWER OF ATTORNEY DATE: 2021-11-23 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, The Wand Company Ltd are not subject to a denial of federal benets pursuant to Section 5301 of the Anti-

Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benets pursuant to that section. Sincerely, The Wand Company Ltd Richard Blakesley / Manager