Users Manual This manual contains the name of each part of RTSB7000L, how to operate it, how to connect it to a smartphone, how to set up the product, and service Quality Warranty All hardware products manufactured and produced by our company have been passed after strict quality control and inspection. A. Warranty period Body : 1 year All accessory(Battery) : 6 months Period of repair parts : 5 years from the date of the model release B. Warranty contents
- In the event of failure on normal use during warranty period, we provide free of charge repair service in our Service center.
- If you switch general product to the commercially, warranty period is reduced to half.
- All components excepting main body are Consumables. (Based on full productbox condition)
- In the following cases, even within the warranty period, some actual cost of repair can be charged or the repair service may be not possible at a cost. 1) Usage of negligence / shock / carelessness / dropping in water 2) If you disassemble or modify the product for other purposes 3) Breakdown by natural disaster like re, earthquake, ood etc. 4) If the product is repaired outside of our service center 5) If the product is not service guaranteed product or requested for service in outside of the service guarantee area
- Individual items that are not explicitly stated in this section are based on our service center and customer support operating principles and internal regulations, and other matters are reviewed and implemented for the convenience of end users. C. Warranty of specic parts
- Optical Module More than 5 defective pixels : Within warranty period (Replacement free of charge) / After warranty period (service at a cost) We replace optical module in case of the product with defective pixels and please note that the replacement of main body or refund cannot be supported due to the defective pixel product.
- FAN MOTOR In case of severe noise : Within warranty period (Replacement free of charge) / After warranty period (service at a cost) We replace in case the noise exceeds the measurement noise specied by our company. Please note that exchange of the product or refund is not supported. D. Details on product replacement
- Application Principle Only in case there is a reasonable reason to exchange the products on the basis of Fair Trade Act, Consumer Protection Rule and the interpretation of the Consumer Protection Authority for the same/similar cases. And, when exchanging products, only 1:1 exchange with the same model is possible.
(You cannot exchange products with similar or other models)
- Note: If you apply Warranty service, you must have purchase receipt with yourself.
- Subject of Application The products that have the history to apply warranty service 4 times and more due to the same defects during the warranty period The products that have the history to apply warranty service 5 times and more due to the different defects during the warranty period If the manufacturer lost the product that the consumer asked for repair, it will be exchanged or refunded. If there are no repair parts during the period of parts retention, it will be exchanged or refunded. Safety Notice Please read it carefully before use. Precautions
- If this product is used over 20 hours continuously, power is cut off automatically to protect the system of product. This is not defective.
- Do not close/block any ventilation openings on the sides of beam projector. It causes malfunction by overheating or it can deteriorate performance.
- Do not use the projector near water or moisture. To reduce the risk of re/electric shock, do not expose the projector to rain or moisture.
- Do not install/put/use the beam projector near heat sources such as radiators, heater, stoves or any other apparatus such as ampliers that emit heat.
- Do not use the projector in direct sunlight.
- Do not use the beam projector in places in strong magnetic eld. (Microwave, etc.). It can cause incorrect function to the product.
- Do not use the beam projector where severe contamination occurs. (Dust, etc.)
- If you do not use the beam projector for a long-term, product may be discharged. Please periodically charge every 2-3 months.
- Do not put the beam projector in mouth or do not drop it.
- If the product is exposed to moisture or humid environment, damage can occur in parts and circuits. occur in parts and circuits.
- If the product is exposed to moisture or humid environment, damage can
- Only use attachments and accessories specied by the manufacturer.
- If the exterior of the device is damaged/abused, do not use the projector.
- In case of the following conditions, damage/abuse can be happened.
(They are the part of possible problems)
- When the beam projector is dropped.
- When the charger or plug is damaged.
- When liquid has been spilled into the beam projector.
- When the beam projector is disclosed to rain or humidity
- When a foreign substance gets into the beam projector or when internal components of beam projector get loose. Do not repair personally in above situation. When you remove or put on the cover of the product, you may be exposed to dangerous voltage or other hazards. Before sending the product for repair, please contact your local dealer/reseller or service center.
- In case of connecting a smart phone to wireless beam projector while you are charging the smart phone, please use the genuine power charger that has genuine product certicate for your smart phone or there is a possibility of problem on the wireless data transmission by wrong noise. Or charge the projector enough and remove the charging cable before use it.
- When using the projector, please use a genuine micro USB charger that supports more than 2A. (Product package includes a micro USB charging cable.) Product Specication Components Mode Switching Connect (iOS) 1) Press and hold the Power button for 3 seconds to turn on the device 2) After turning on the device, please select your smartphone settings 3) Please nd the name of Smart Beam device (PocketTheater_XXXX) in Wi-Fi setting and connect. Video
(Optical engine) Item Display Brightness Source of Illumination Aspect Ratio / Contrast Ratio Screen Size Proper Projection Distance LED Life Color Temperature Throw Ratio Operate Temparature Power General Size Weight Battery Audio and Output LED Display Light Radio Frequency Software Button Power Consumption Speaker (8 standard) Frequency Range DC IN No External Power Charge completed Battery is charging Low battery USB Charge Current Lack Update Error Recovery Range Language Power Function Key Specication DLP Pico Projector, nHD (640 x 360) Maximum 50 Lumens R,G,B LED 16:9, 1000:1 10 inch ~ 60 inch 0.3m ~ 2.2m 20,000 Hours 6,900 ~7,200K 1.72 0~40 DC 5V / 2.0A, Micro USB Width 52.0mm Length 52.0mm Height 27.7mm Width 2 in. Length 2 in. Height 1 in. Approx. 70g (2.46oz / 0.15lbs) 1,800mA, Up to 1hour 50min. 7.0W (Operating) 6.7W (Charging after Power OFF) 1W. MONO MIXER Output / Signal to Noise Ratio : 90dB 20Hz ~ 20KHz Micro USB Off Green Orange Red LED ickering Red Red & Green LED ickering in turn 2.4GHz, 5GHz English Power ON/OFF Focus(Front), Focus(Rear) User Manual Projector User Manual MICRO 5pin cable Toroidal Ferrite Core The component can be changed without previous notice for the quality or function improvement. How to use Power button Power on/off Press and hold the Power button for approximately 3-5 seconds. The screen is displayed in 6~10 seconds. Press and hold the Power button again for 3~5 seconds for power off. Focus(Front) Adjusting focus Focus(Rear) Adjust back and forth until the image on screen becomes clear. Pushing focus (front / rear) buttons simultaneously, it performs the mode-switching function between Miracast (Android) mode and DLNA
(iOS) mode. Battery Charging When Micro USB charger (Micro 5 pin cable) connects DC IN of the product, charging starts.
(Note: Use Micro 5 pin cable that has genuine product certication.) The charging time takes about two hours and a bit more. (This is the case of using the genuine charger on power-off status after full discharge. Also, depending to the charger, charging time can be different.) To reduce the inuence of electromagnetic waves, use Micro 5pin cable after installing a core included in the component. Please refer to the installation of the ferrite core in FCC section of the other page. Learning Basic 1) Power On / Initial operating Power on by pressing and holding the Power button for 3~5 seconds. Please wait for a while until screen displayed in 6~10 seconds. Standby mode after booting is Miracast. 2) Screen mode for AirPlay and waiting for connection After booting, if the following image is displayed on the screen, it is a normal connection of waiting status. 3) Setting up smart device AirPlay / DLNA Device Name : PocketTheater_XXXX Status : Waiting for connection... Please connect your device to beam using the WiFi. For more information, please visit www.to21comms.com FCC Model Name: RTSB7000L FCC ID: 2AMJ7-RTSB7000L This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. CAUTION : Changes or modications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions. 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. INSTALLING THE FERRITE CORE ON THE USB CABLE Lift up to release the lock and open the core. Place the cable on the opened core. Close the lock. Toroidal Ferrite Core FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. Connect (Android) 1) Press and hold the Power button for 3 seconds to turn on the device. 2) After turning on the device, switch the beam mode of Miracast. Miracast Device Name : Pocket Theater_XXXX Status : Waiting for connection... 3) Please connect as shown below;
(Samsung: Smart View / Screen Mirroring, LG: Miracast) AirPlay Mirroring PocketTheater_XXXX PocketTheater_XXXX PocketTheater_XXXX LG mobile Smartphone Samsung mobile Smartphone 4) Connect AirPlay by sliding up the scroll bar at the bottom of your iPhone. 5) Select AirPlay, then select PocketTheater_XXXX under the device name
(Be sure to select the Mirroring switch for screen mirroring). 6) Adjust the screen size by adjusting the distance between the smart beam and the screen. 7) Use the Focus button (Front/Rear) right under the product Power button to adjust the focus on the screen. Smart View Smart View Select device PocketTheater_XXXX Mirror the screen. Connection to PocketTheater_XXXX CANCEL