TP825Q Product Specification
& Customer Design Guide Rev 1.4 Dec 20, 2013 v 1.4 TP825Q Android Solution Module Touchcom TP series Product Specification & Customer Design Guide Copyright 2013 Touchcom Wireless. All rights reserved. Contact Information Sales:
Tel:
+886-2-6606-3393 Fax: +886-2-6600-8196 Hours: 9:00 am to 5:00 pm (GMT +8:00) Email: sales@touchcom.tw Address: Touchcom wireless 10550 Rm. A1, 3F., No.261, Sec. 3, Nanjing East Rd., Songshan Dist., Taipei City Taiwan Web:
www.touchcom.tw Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 1 of 42 TP825Q Product Specification
& Customer Design Guide Revision History Rev No. Release Date Changes Rev 1.4 Dec 20, 2013 Sep 10, 2013 Draft document creation Oct 04, 2013 Oct 31, 2013 Nov 14, 2013 Updated power supply in chapter 3 Revised Pin assignment I/O define error Added on RF chapter SMT PCB Pads recommends Pin number final confirmed. Pin description added MDP_VSYNC_P Dec 20, 2013 Final production release 0.9 1.1 1.2 1.3 1.4 Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 2 of 42 Rev 1.4 Dec 20, 2013 TP825Q Product Specification
& Customer Design Guide Contents 1. Introduction 1.1 Product Overview 1.2 General Features 2. Interfaces 2.1 System Design 2.2 Pin Description 2.2.1 Main Interface 2.2.2 Camera Interface 2.2.3 RF Connector 3. Power 3.1 Power Supply 3.2 Battery Charging Interface 3.3 USB 2.0 Interface 3.4 VCC_2V8 and VCC_1V8 Output 4. Audio Interface 4.1 Analog Audio 4.1.1 Microphone 4.1.2 Speaker 4.2 Handset 4.3 Digital Audio 5. Interfaces 5.1 SDIO Interface (microSD / TF Card) 5.2 Vibrating Motor 5.3 USIM Interface 5.4 UART Interface 5.5 I2C Interface 5.6 TP Interface 5.7 Keypad Interface 5.8 LCD Interface 5.9 LED Driver 5.10 GPIO Interface 6. Camera Interfaces 6.1 System Design 7. RF Interfaces 7.1 RF Connections 7.1.1 Antenna 7.1.2 Antenna Connector 7.2 GSM + WCDMA Parts 7.2.1 Frequency support 7.2.2 Conducted Tx (Transmit) power tolerances 7.3 Wi-Fi + BT Parts Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 3 of 42 TP825Q Product Specification
& Customer Design Guide 7.4 GPS Parts 8. Power Consumption Rev 1.4 Dec 20, 2013 8.1 System Power consumption ( with 7.9 TFT LCD ) 9. Soldered Solution and Mechanical Specifications 9.1 Recommended foot print for the Main application 9.2 Recommended foot print for the MIPI application 9.2.1 PCB Reserve Area for MIPI interface This is an area recommended to reserve having a mechanical part on main or daughter PCB of module placement for MIPI interface application in direct contact with the module. 9.2.2 Solder pad design for MIPI application 9.3 PCB pad design 9.4 Solder paste 9.5 Mechanical dimensions 9.6 Labeling 10. Certification Compliance and Recommended Standards 10.1 Certification Compliance 10.2 Applicable Standards 10.2.1 Important Notice 10.2.2 Safety and Hazards 10.2.3 Important Compliance Information for Unite America Users 10.2.4 EU Regulatory Conformity 10.2.5 Important Compliance Information for Taiwan Users Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 4 of 42 TP825Q Product Specification
& Customer Design Guide 1. Introduction Rev 1.4 Dec 20, 2013 1.1 Product Overview The TP-825Q SOM (System on Module) is a full featured Android 4.1.2 (Jelly Bean) development platform that provides an easy way for creating low-cost, high-performance embedded or handheld devices. Based upon Qualcomm Snapdragon 200 MSM8225Q quad-core processor that integrated PM8029 (PMIC), RTR6285A (RFIC), AR6005 (Wi-Fi), WCN2243 (BT). The TP-825Q incorporates quad-core high performance up to 1.2GHz CPUs, a powerful multimedia engine support, GSM, GPRS, WCDMA, HSPA, Wi-Fi (802.11 b/g/n), Bluetooth (BT3.0 + A2DP), a full suite GPS, USB connectivity and camera function, etc. 1.2 General Features Features Descriptions Physical features Small form factor Two W.FL RF connector jacks Electrical features Single supply voltage (VCC): 3.6V - 4.2V Self-shielded - no additional shielding required RF Quad-band GSM/GPRS (850 / 900 / 1800 / 1900 MHz) Tri-band WCDMA/HSPA (850 / 1900 / 2100 MHz) Wi-Fi (2.4 GHz) Bluetooth (2.4 GHz) GPS (1575.42MHz) Operating System Android 4.1.2 (Jelly Bean) Processor Qualcomm MSM8225Q (Quad-core Cortex-A5 1.2GHz) Memory / Storage 1GB LPDDR2 / 4GB eMMC Camera Wi-Fi Bluetooth G-Sensor Support up to 8MP resolution rear-facing camera with AF Support up to 2MP resolution front-facing camera 2.4 GHz IEEE 802.11 b/g/n Bluetooth 3.0 support A2DP (HW compliant with BT4.0/BLE) Yes Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 5 of 42 TP825Q Product Specification
& Customer Design Guide Rev 1.4 Dec 20, 2013 Color Numbers 24Bit RGB (support 800x480, 1024x600, 1024x768, 1280x800) or 24Bit MIPI Graphic Card Adreon 203 Standalone GPS functionality A-GPS features gspOneXTRA Operating temperature range:
-30 C to +75 C Storage temperature range:
-40 C to +85 C Relative humidity range:
5% to 95%
300 mA for USB 5V charging 900 mA for DC charging USB 2.0 (OTG) 60 x 46 x 2.6 (mm) GPS Environment Charge USB Dimension Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 6 of 42 TP825Q Product Specification
& Customer Design Guide 2. Interfaces Rev 1.4 Dec 20, 2013 2.1 System Design This chapter describes the TP-825Q module connector interface configuration and supported interfaces. The module includes the following interfaces:
Main Interface Description Power Supply Supplied to the module power Battery Charging Battery power charging and temperature monitor Standard Power Output power to all external devices (2V8 and 1V8) Audio PCM SDIO Motor USB SIM UART I2C GPIO Analog audio interface (Speaker/Microphone/Handset/Earpiece) Digital audio interface SDIO standard, T-Flash (microSD) card support Hot swap, Plug & Play Vibrating motor support USB2.0 Slave (support OTG) SIM / USIM card support 2-wire serial interface Standard I2C bus, used for TP or other external devices Digital ON/OFF function (1V8) Keypad One power key, two descriptive keys and key backlight support LCD LED Power/Control/Data line to 24Bit LCD display Two descriptive LEDs Camera Interface Description MIPI Dual MIPI interface, support 8MP (Rear camera) and 2MP (Front camera) RF Connector Description Main GSM / GPRS / WCDMA RF connector Wi-Fi / BT / GPS RF connector WiFi/BT/GPS Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 7 of 42 TP825Q Product Specification
& Customer Design Guide 2.2 Pin Description 2.2.1 Main Interface Rev 1.4 Dec 20, 2013 Pin# Signal Name Description I/O Voltage Type 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 MIC2_P MIC2_M GND Handsets Mic Input Positive Handsets Mic Input Negative Ground MSM_MICBIAS Main Microphone Bias GND MIC1_M MIC1_P GND SDC1_CLK SDC1_D2 SDC1_CMD SDC1_D0 SDC1_D1 SDC1_D3 VIB_EN Ground Main Mic Input Negative Main Mic Input Positive Ground microSD Clock microSD Data 2 microSD command microSD Data 0 microSD Data 1 microSD Data 3 Vibration Motor VBATT_TEMP Battery Temperature Sensor GND VBATT VBATT GND Ground Power Supply Input Power Supply Input Ground RESET_VBATT Module Reset VPH_PWR VPH_PWR Power Supply Output Power Supply Output I
-
I I
-
I O O Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW I I
-
-
-
I I
-
-
-
GND 2.2V GND
-
-
Analog Analog
-
Analog
-
Analog Analog GND
-
O 2V8 I/O 2V8 O 2V8 I/O 2V8 I/O 2V8 I/O 2V8 O 2V8
-
Digital Digital Digital Digital Digital Digital Analog Analog GND
-
3V6 ~ 4V2 Analog 3V6 ~ 4V2 Analog GND
-
3V3 ~ 4V2 Analog 3V6 ~ 4V2 Analog 3V6 ~ 4V2 Analog Page 8 of 42 TP825Q Product Specification
& Customer Design Guide 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 GND EAR_P EAR_N GND Ground Earpiece Output Positive Earpiece Output Negative Ground PMIC_HPH_R Earphone Right Channel Output GND Ground PMIC_HPH_L Earphone Left Channel Output GND SPK_OUT_P SPK_OUT_M GND Ground Speaker Output Positive Speaker Output Negative Ground HSED_BIAS1 Headset Mic Bias USB_HS_VBUS USB VBUS VREG_L12 VREG_L13 VREG_L16 MB_IN TP VCC Supply microSD VCC Supply SIM VCC Supply Handset Button UIM1_RESET USIM Reset UIM1_CARD_RMV_N USIM Detection UIM1_CLK UIM1_DATA USIM Clock USIM Data I/O AUX_PCM_SYNC Auxiliary PCM Sync TP_RES DC_DET TP Reset DC Charging Detect AUX_PCM_DOUT Auxiliary PCM Data Output PHONE_ON_N Power Button Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Rev 1.4 Dec 20, 2013
-
O O
-
O
-
O
-
O O
-
-
-
-
-
-
I O I O GND
-
-
-
Analog Analog GND
-
Analog GND
-
-
Analog GND
-
-
-
Analog Analog GND
-
-
5V 2V8 2V8 Analog Analog Analog Analog 1V8 or 2V8 Analog 1V8 Analog 1V8 or 2V8 Digital 1V8 or 2V8 Digital 1V8 or 2V8 Digital I/O 1V8 or 2V8 Digital O O I O I 1V8 1V8 1V8 1V8 1V8 Digital Digital Digital Digital Digital Page 9 of 42 TP825Q Product Specification
& Customer Design Guide 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 KYPD_DRV1 Volume Decrease Key AUX_PCM_CLK Auxiliary PCM Clock AUX_PCM_DIN Auxiliary PCM Data Input KYPD_DRV0 Volume Increase Key KEYSENSE_N1 GND VREG_S3 Keypad Ground VCC_1V8 CAP_TS_INT_N TP Interrupt I2CI_SDA I2CI_SCL I2C Data I2C Clock PWM_LCD_BLCK LCD PWM Backlight GND USB_HS_DN USB_HS_DP GND USB_HS_ID LCDC_RED0 Ground USB Data Negative USB Data Positive Ground USB OTG ID LCD Red Data 0 LCDC_GREEN7 LCD Green Data 7 LCDC_PCLK LCD Clock UART1_RX UART1_TX UART1 Rx Data UART1 Tx Data LCDC_GREEN5 LCD Green Data 5 LCDC_BLUE2 LCDC_BLUE6 LCD Blue Data 2 LCD Blue Data 6 LCDC_GREEN4 LCD Green Data 4 LCDC_GREEN1 LCD Green Data 1 Rev 1.4 Dec 20, 2013 O O I O I
-
-
1V8 1V8 1V8 1V8 1V8 GND 1V8 I/O 1V8 I/O 1V8 O O
-
1V8 1V8 GND I/O 3V3 I/O 3V3
-
I GND 5V I/O 1V8 I/O 1V8 O I O 1V8 1V8 1V8 I/O 1V8 I/O 1V8 I/O 1V8 I/O 1V8 I/O 1V8 Digital Digital Digital Digital Digital
-
Analog Digital Digital Digital Analog
-
Digital Digital
-
Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 10 of 42 TP825Q Product Specification
& Customer Design Guide 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 LCDC_RED7 LCD Red Data 7 LCDC_VSYNC LCD VSync LCDC_GREEN3 LCD Green Data 3 MDP_VSYNC_P Vertical sync to/from MDP LCDC_BLUE4 LCD Blue Data 4 LCDC_GREEN0 LCD Green Data 0 LCDC_BLUE7 LCD Blue Data 7 LCDC_RED6 LCDC_RED5 LCD Red Data 6 LCD Red Data 5 LCDC_HSYNC LCD HSync LCDC_BLUE1 LCDC_BLUE3 LCDC_BLUE5 LCD Blue Data 1 LCD Blue Data 3 LCD Blue Data 5 LCDC_GREEN2 LCD Green Data 2 LCDC_BLUE0 LCD Blue Data 0 LCDC_GREEN6 LCD Green Data 6 LCDC_RED4 LCDC_RED2 LCDC_RED1 LCDC_RED3 GND LCDC_DEN SDC1_DET LCD Red Data 4 LCD Red Data 2 LCD Red Data 2 LCD Red Data 3 Ground LCD Enable microSD Detection LCDC_LVS_OE LCD Voltage Shift 100 HS_DETECT_N Handset Detection 101 LCD_RST_N LCD Reset Rev 1.4 Dec 20, 2013 I/O 1V8 O 1V8 I/O 1V8 I/O 1V8 I/O 1V8 I/O 1V8 I/O 1V8 I/O 1V8 I/O 1V8 O 1V8 I/O 1V8 I/O 1V8 I/O 1V8 I/O 1V8 I/O 1V8 I/O 1V8 I/O 1V8 I/O 1V8 I/O 1V8 I/O 1V8
-
O I GND 1V8 1V8 I/O 1V8 I O 1V8 1V8 Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital Digital
-
Digital Digital Digital Digital Digital Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 11 of 42 Digital Digital Digital Digital Digital Digital
-
-
TP825Q Product Specification
& Customer Design Guide Rev 1.4 Dec 20, 2013 102 EXT_APA_EN External Amplifier Enable/Disable O 1V8 Digital 103 GND 104 FM_ANT 105 GND Ground FM Radio Antenna Ground 106 LCD_LEDPWR_EN LCD Backlight Enable/Disable 107 OTG_5V_EN OTG Enable/Disable 108 EXT_LCD_PWR_EN LCD VCC Enable/Disable
-
I
-
O O O 1V8 1V8 1V8 GND
-
-
Analog GND
-
109 LIGIT_P_EN Keypad/Camera Flash Light I/O 1V8 110 LED_GREEN_EN Green LED Output 111 LED_RED_EN Red LED Output Ground Ground 112 GND 113 GND 2.2.2 Camera Interface O O
-
-
1V8 1V8 GND GND Pin# Signal Name Description I/O Voltage Type 1 2 3 4 5 6 7 8 9 GND DOVDDF DOVDDF GND AVDDF Ground Front Cam Power Supply Front Cam Power Supply Ground Front Cam Power Supply CAM_1MP_PWDN Front Cam Enable/Disable CAM_1MP_RESET Front Cam Reset GND Ground I2C0_SCL_F3 Front Cam I2C Clock
-
O O
-
O O O
-
O GND 1V8 1V8 GND 2V8 1V8 1V8 GND 1V8 10 I2C0_SDA_F3 Front Cam I2C Data I/O 1V8
-
Analog Analog
-
Analog Digital Digital
-
Digital Digital Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 12 of 42 TP825Q Product Specification
& Customer Design Guide 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 GND Ground MIPI_CSI1_CLK_N Front Cam MIPI Clock Negative MIPI_CSI1_CLK_P Front Cam MIPI Clock Positive GND Ground MIPI_CSI1_LANE0_N Front Cam Lane 0 Negative MIPI_CSI1_LANE0_P Front Cam Lane 0 Positive GND Ground CAM_MCLK_1MP Front Cam Main Clock GND NC GND AF GND AF VDD Ground
-
Ground Rear Cam Auto Focus Ground Rear Cam Auto Focus Power Supply CAM_5MP_PWDN_VCM Rear Cam Power Down GND DOVDDB GND AVDDB Ground Rear Cam Power Supply Ground Rear Cam Power Supply CAM_5MP_RESET Rear Cam Reset CAM_5MP_SHDN_N Rear Cam Enable/Disable GND I2C0_SDA I2C0_SCL GND Ground Rear Cam I2C Data Rear Cam I2C Clock Ground CAM_MCLK_5MP Rear Cam Main Clock GND Ground Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Rev 1.4 Dec 20, 2013
-
Digital Digital
-
Digital Digital
-
Digital
-
-
-
-
Analog Digital
-
Analog
-
Analog Digital Digital
-
O O
-
GND 1V8 1V8 GND I/O 1V8 I/O 1V8 GND 1V8 GND NC GND GND 2V8 1V8 GND 1V8 GND 2V8 1V8 1V8
-
O
-
-
-
-
O O
-
O
-
O O O
-
GND
-
I/O 1V8 O
-
O
-
1V8 GND 1V8 GND Digital Digital
-
Digital
-
Page 13 of 42 37 38 39 40 41 42 43 44 TP825Q Product Specification
& Customer Design Guide Rev 1.4 Dec 20, 2013 MIPI_CSI2_CLK_P Rear Cam MIPI Clock Positive MIPI_CSI2_CLK_N Rear Cam MIPI Clock Negative GND Ground MIPI_CSI2_LANE0_N Rear Cam Lane 0 Negative MIPI_CSI2_LANE0_P Rear Cam Lane 0 Positive GND Ground I/O 1V8 I/O 1V8 Digital Digital
-
GND
-
I/O 1V8 I/O 1V8 Digital Digital
-
GND
-
MIPI_CSI2_LANE1_N Rear Cam Lane 1 Negative MIPI_CSI2_LANE1_P Rear Cam Lane 1 Positive I/O 1V8 I/O 1V8 GND Ground 45
* Connector is HIROSE FH26-45S-0.3SHW More information is also available from http://www.hirose.co.jp/cataloge_hp/e58302093.pdf . GND
-
Digital Digital
-
2.2.3 RF Connector Pin# Description M3 m8 GSM + GPRS + WCDMA antenna RF cable connector GSM + GPRS + WCDMA RF test point M5 Wi-Fi + BT + GPS antenna RF cable connector m7 Wi-Fi + BT + GPS RF test point
* M3 M5 Connector is HIROSE W.FL2-R-SMT-1(60)
* m7 m8 Connector is MuRata MM8130-2600
- m7 and m8 are the test point for factory, it will break the signal out to M3 or M5 when MuRata MXHS83QE3000 probe. Please contact us to get more information about the connector. Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 14 of 42 TP825Q Product Specification
& Customer Design Guide 2.3 Electrical Information for Digital I/O Digital I/O characteristics for VDD = 2.8 Volt Rev 1.4 Dec 20, 2013 Parameter Comments Min Typ Max Unit Internal 2V8 power supply VCC_2V8 2.7 2.8 3.0 V VIL High-level input voltage CMOS / Schmitt 0.65 * VDD VIH Low-level input voltage CMOS / Schmitt
-0.3 VOL High-level output voltage VOH Low-level output voltage CMOS, at rate drive strength CMOS, at rate drive strength IIHPD Input high leakage current With pull-down IILPU Input low leakage current With pull-up Input capacitance CIN Digital I/O characteristics for VDD = 1.8 Volt VDD - 0.45 0 10
-60
-
-
-
-
-
-
-
-
VDD + 0.3 V 0.35 * VDD V VDD 0.45 60
-10 5 V V A A pF Parameter Comments Min Typ Max Unit Internal 2V8 power supply VCC_1V8 1.7 1.8 1.9 V VIL High-level input voltage CMOS / Schmitt 0.65 * VDD VIH Low-level input voltage CMOS / Schmitt
-0.3 VOL High-level output voltage VOH Low-level output voltage CMOS, at rate drive strength CMOS, at rate drive strength IIHPD Input high leakage current With pull-down IILPU Input low leakage current With pull-up Input capacitance CIN VDD - 0.45 0 5
-30
-
-
-
-
-
-
-
-
VDD + 0.3 V 0.35 * VDD V VDD 0.45 30
-5 5 V V A A pF Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 15 of 42 TP825Q Product Specification
& Customer Design Guide 3. Power 3.1 Power Supply Name VBATT Pin #
18, 19 Description Module power supply Ipeak VPH_PWR 22, 23 All external devices power supply RESET_VBATT 21 Module reset GND Ground 3, 5, 8, 17, 20, 24, 27, 29, 31, 34, 55, 61, 64, 96, 103, 105, 112, 113 Rev 1.4 Dec 20, 2013 Min Typ Max Unit 3.6 3.7 4.2 V 3.6 3.3
-
2.5 A 3.7 4.2 V
-
-
4.2 V
-
-
Since the maximum peak current of module can reach 2.5A, we strongly recommend having a large width and short for the layout of the power supply signal (to avoid voltage loss between the external power supply and the TP-825Q SOM supply). VPH_PWR is all external devices component power supply totals power form module, generally form 3.6V to 4.2V. VPH_PWR through the circuits inside P8029 and no external circuits are required to generate If the battery is used only, VPH_PWR will be generated by the battery. And the voltage is the same as the batterys voltage. The VPH_PWR to component total maxiuman current supply is 1000mA. Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 16 of 42 TP825Q Product Specification
& Customer Design Guide 3.2 Battery Charging Interface Rev 1.4 Dec 20, 2013 Name DC_DET Pin # Description 47 DC power detection Min Typ Max Unit 1.7 1.8 1.9 V 16 Battery temperature detection VBATT_TEMP The TP-825Q SOM provide two types of charging currents, USB-DC for 300mA and AC-DC for 900mA. It is using DC_DET pin to check what is the charging type using. 1. VBATT_TEMP is the temperature monitor for the Li-Ion battery, it should be connected to batterys TX pin for temperature senose. If your battery dont have it, please connected 100K NTC when layout. 2. If you dont use DC_DET, please connect it with 10K. 3.3 USB 2.0 Interface Name Pins Description USB_HS_VBUS USB_HS_DN USB_HS_DP USB_HS_ID 36 62 63 65 USB VBUS 5V USB Data negative USB Data positive USB OTG ID VTyp Type 5V
-
-
5V
-
IO IO I 107 OTG enable pin OTG_5V_EN The USB interface is compliant with Version 2.0 of the USB standard for high speed operation. (Maximum signaling rate of 48 Mbps) USB_HS_ID / OTG_5V_EN For USB OTG using. Must add OTG_5V when using USB OTG. Provide 5V to USB_VBUS when using USB OTG. 1V8 O Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 17 of 42 TP825Q Product Specification
& Customer Design Guide 3.4 VCC_2V8 and VCC_1V8 Output These digital power supplies are used to:
Act as a voltage reference pin Supply the external devices Rev 1.4 Dec 20, 2013 Pin # Description Min Typ Max Unit 37 38 56 TP power supply or other devices 2.7 2.85 3.0 V 300 mA MicroSD power supply or other devices 2.7 2.85 3.0 V 1.8V voltage reference 300 mA 1.7 1.8 1.9 V 500 mA Name VREG_L12 VREG_L13 VREG_S3 Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 18 of 42 TP825Q Product Specification
& Customer Design Guide 4. Audio Interface 4.1 Analog Audio Name MIC1_M MIC1_P MSM_MICBIAS SPKR_OUT_P SPKR_OUT_M Pins Description 6 7 4 32 33 Main microphone negative input Main microphone positive input Main microphone bias output voltage Speaker positive output Speaker negative output EXT_APA_EN 102 External audio amplifier enable pin EAR_P EAR_M 25 26 Earpiece positive output Earpiece negative output 4.1.1 Microphone Rev 1.4 Dec 20, 2013 VTyp Type
-
-
2V2
-
-
AI AI
-
AO AO 1V8
-
-
-
AO AO Parameter Comment Min Typ Max Unit Microphone inputs only Input common mode voltage DC 1.13 1.25 1.38 V MIC bias supply voltage Open circuit DC voltage 1.69 1.80 1.91 V MIC bias output source current DC; 1.69 k 1% resistive load 1 1.07 Muted MIC attenuation
+3 dBm0, 1.02 kHz sinewave input Common to voice/audio modes Input impedance Differential configuration Single-ended configuration Input capacitance Input offset voltage Measurement bandwidth is 22 Hz to Fs/2 (Fs = sample rate) At each pin At each pin 80 16 8
-
-
20 10 5
-
24 12
-
mA dB k k pF 5 mV Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 19 of 42 TP825Q Product Specification
& Customer Design Guide Absolute gain error Differential, -10 dBm0 input Single-ended, 0 dBm0 input Gain error
+3 dBm0 to -30 dBm0 input
-31 dBm0 to -45 dBm0 input
-46 dBm0 to -55 dBm0 input 4.1.2 Speaker Parameter 16 or 32 support Input frequency range Input resistance Output power Normal operation (+3.6V, 8) High-power audio (+5V, 8) High-power audio (+5V, 4) Power efficiency Normal operation (+3.6V 500mW, 8) High-power audio (+5V 1W, 8) High-power audio (+5V 2W, 4) Rev 1.4 Dec 20, 2013 All gain settings: MIC1 = 0 or +24 dBl MIC2 = -6 to +25.5 dB in 1.5 dB steps; Fs = 8 or 16 kHz Relative to gain at -10 dBm0 input; Fs = 8 or 16 kHz
-1.0
-1.0
-0.5
-1.0
-1.2
-
-
-
-
-
1.0 1.0 0.5 1.0 1.2 dB dB dB dB dB Comment Min Typ Max Unit 0.02
-
20 kHz 15 20.2 27 k
-
-
-
85 85 80 630 1.2 2.4 88 90 85
-
6 0
-
-
-
-
-
-
-
mW W W
%
%
%
+18 dB
-
dB
+1 dB
+0.5 dB Amplifier gain, normal operation Programmable, 2 dB increments
-12 Add to normal operation settings 20 Hz to 20 kHz
-
-1
-0.5 Boost gain Amplifier gain error Amplifier gain flatness Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 20 of 42 TP825Q Product Specification
& Customer Design Guide 4.2 Handset Rev 1.4 Dec 20, 2013 Pin # Description VTyp Type Name MIC2_P MIC2_M PMIC_HPH_R PMIC_HPH_L HSED_BIAS1 1 2 28 30 35 Handsets microphone positive input Handsets microphone negative input Handsets right audio channel output Handsets left audio channel output Handsets microphone bias output voltage HS_DETECT_N 100 Handset detection pin 40 MB_IN MB_IN is ADC input, support Talk/Off button and volume control key. Handset button detection 4.3 Digital Audio Name Pin # Description AUX_PCM_SYNC AUX_PCM_DOUT AUX_PCM_CLK 45 48 51 PCM frame synchronization 8 kHz PCM Data output PCM Data clock AUX_PCM_DIN The Digital Audio Interface also features the following:
PCM Data input 52
-
-
-
-
2V2 1V8 1V8 AI AI AO AO
-
I AI VTyp 1V8 1V8 1V8 1V8 Type O O O I IOM-2 compatible device on physical level Master mode only with 6 slots by frame, user only on slot 0 Bit rate single clock mode at 768kHz only 16 bits data word MSB first only Linear Law only (no compression law) Long Frame Synchronization only Push-pull configuration on PCM_DOUT and PCM_DIN Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 21 of 42 TP825Q Product Specification
& Customer Design Guide 5. Interfaces Rev 1.4 Dec 20, 2013 5.1 SDIO Interface (microSD / TF Card) Name Pin # Description Min Typ Max Unit VREG_L13 38 microSD card power supply 2.7 2.85 3.0 V SDC1_CLK SDC1_D2 SDC1_GND SDC1_D0 SDC1_D1 SDC1_D3 9 10 11 12 13 14 microSD Clock microSD Data 2 microSD Command, Response microSD Data 0 microSD Data 1 microSD Data 3 2.8 2.8 2.8 2.8 2.8 2.8 98 microSD card hot plug detection pin SDC1_DET Support SD 4-bit data transfer mode, clock speed is 25 MHz, burst rate is up to 100 Mbit/s. SDC1_DET is used for microSD card hot plug detection pin (High: removed, Low: Inserted) 1.8 300 mA V V V V V V V 5.2 Vibrating Motor Pin # Description Min Typ Max Unit 15 Directly drive the vibrating motor 2.7 2.8 3.0 V 100 mA Name VIB_EN #
Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 22 of 42 TP825Q Product Specification
& Customer Design Guide 5.3 USIM Interface The USIM pins provide the connections necessary to interface to a SIM socket located on the host device. Voltage levels over this interface comply with 3GPP standards. Rev 1.4 Dec 20, 2013 Name Pins Description VTyp Imax Type VREG_L16 UIM1_RESET UIM1_CARD_RM V_N 39 41 42 USIM Power Supply USIM Reset USIM Card Detect UIM1_CLK 43 USIM Clock 44 UIM1_DATA The interface support SIM (1.8V), USIM (3.0V) and fully compliant with USIM Data I/O
(2G) 3GPP TS 51.010-1, section 27.17.
(3G) ETSI TS 102 230 V5.5.0, section 5.2. 1.8V/2.8V 50mA 1.8V/2.8V 1.8V/2.8V 1.8V/2.8V 1.8V/2.8V
-
-
-
-
O O I O IO UIM1_CARD_RMV_N: Only for detecting SIM Card inserted and didnt support how-swap SIM function. 5.4 UART Interface Name Pins Description UART1_RX 69 UART1 RX Data 70 UART1_TX The maximum baud rate of UART1 is 115200 8N1 (no HW/SW flow control). UART1 TX Data 5.5 I2C Interface Name Pins Description I2C1_SDA 58 I2C data line VTyp 1V8 1V8 Type I O VTyp Type 1.8V IO 59 I2C clock line I2C1_SCL The I2C Bus interface includes a clock signal (I2C1_SCL) and a data signal (I2C1_SDA) complying with a 100Kbit/s-standard interface (standard mode: s-mode). The I2C bus is always in master mode operation. Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW 1.8V O Page 23 of 42 TP825Q Product Specification
& Customer Design Guide The maximum speed transfer is 400Kbit/s (fast mode: f-mode). For more information on the I2C bus, see document I2C Bus Specification, Version 2.0, Philips Semiconductor 1998. Rev 1.4 Dec 20, 2013 5.6 TP Interface Name Pins Description CAP_TS_INT_N 57 TP interrupt line VTyp Type 1.8V IO 46 TP reset TP_RES Connect to the touch panels External Interrupt INT and RESET pin. Touch panel ICs voltage must be 1.8V. 1.8V O VTyp Type 1.8V 1.8V I I 1.8V O 1.8V O 5.7 Keypad Interface Name Pins Description System power On/Off key Keypad sense Volume decrease key Volume increase key 49 54 53 50 PHONE_ON_N KEYSENSE_N1 KYPD_DRV0 KYPD_DRV1 5.8 LCD Interface Name PWM_LCD_BLC K LCDC_DEN LCD_RST_N LCD_LEDPWR_E N Pins 60 97 101 106 Description VTyp Type PWM signal used for dimming the backlight 1.8V O LCD data/control line enable pin LCD reset LCD LED backlight enable pin 1.8V O 1.8V O 1.8V O Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 24 of 42 TP825Q Product Specification
& Customer Design Guide EXT_LCD_PWR_ EN 108 Rev 1.4 Dec 20, 2013 External LCD power supply enable pin 1.8V O LCDC_PCLK LCDC_VSYNV LCDC_HSYNC LCDC_REDn LCDC_GREENn LCDC_BLUEn 68 77 85 LCD clock LCD vsync LCD hsync 66, 94, 93, 95, 92, 84, 83, 76 81, 75, 89, 78, 74, 71, 91, 67 90, 86, 72, 87, 80, 88, 73, 82 LCD red data line LCD green data line LCD blue data line 1.8V O 1.8V O 1.8V O 1.8V I/O 1.8V I/O 1.8V I/O PWM_LCD_BLCK Dimming the LCDs backlight and frequency is form 200Hz to 250Hz, most of backlight are using 100Hz ~ 100KHz. LCDC_DEN Used to enable/disable the LCD displays control/data interface. Please keep it open-drain if dont use. LCD_RST_N Reset pin to the LCD display. LCD_LEDPWR_EN Used to trun on/off the LCDs backlight. EXT_LCD_PWR_EN Supply power to the LCD display. LCDC_RGB Support 24-bit/18-bit color modes. If you are using LVDS interface, please dont forget to add a voltage-level translation IC. If you are using parallel video (RGB) interface, add or not a voltage-level translation IC depend on your system. 5.9 LED Driver Name Pins Description LED_GREEN_EN 110 Green LED light enable pin LED_REG_EN 111 Red LED light enable pin 5.10 GPIO Interface Name Pins Description MDP_VSYNC_P LCDC_LVS_OE 79 99 Configurable general purpose I/O Configurable general purpose I/O Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW VTyp Type 1.8V O 1.8V O VTyp Type 1.8V 1.8V I/O I/O Page 25 of 42 TP825Q Product Specification
& Customer Design Guide Rev 1.4 Dec 20, 2013 109 Configurable general purpose I/O LIGIT_P_EN LIGIT_P_EN: Used to Keyboard Light / Camera Flash Light / Ambient Light & Proximity Sensor interrupt pin, but it connected to control a LED. LCDC_LVS_OE: Used to control LCD external voltage-level translation IC, but it didnt use on DevKit.. MDP_VSYNC_P: Used to vertical sync to/from MDP, but it didnt use on DevKit. All pins were not use in DevKit, so you could set it to GPIO in SDK. Please keep it open-drain if didnt use. 1.8V I/O 6. Camera Interfaces 6.1 System Design This chapter describes the Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 26 of 42 TP825Q Product Specification
& Customer Design Guide 7. RF Interfaces The TP-825Q module supports three antennas (main, wlan and GPS). The RF interface has a 50 nominal impedance and a high DC impedance. Rev 1.4 Dec 20, 2013 7.1 RF Connections 7.1.1 Antenna Touchcom strongly recommends working with an antenna manufacturer either to develop an antenna adapted to the application or to adapt an existing solution to the application. Both the mechanical and electrical antenna adaptation is one of the key issues in the design of the GSM/UMTS terminal. 7.1.2 Antenna Connector There is a main antenna connection for both 2G and 3G; and a Wi-FI/BT/GPS connection. For the main connection:
W.FL2 pigtails connection on the module top side RF con A wide variety of cables fitted with W.FL2 connectors is offered by HIROSE:
W.FL2 pigtails, Ex: Ref = W.FL-2LP-04N1-A(L)/W.FL-2LP-04N2-A(L)/W.FL-LP-04N1-A(L)/W.FL-LP-04N2-A(L) W.FL2 cable assemblies Between series cable assemblies More information is also available from http://www.hirose-connectors.com/. 7.2 GSM + WCDMA Parts The TP-825Q SOM supports three antennas (main, wlan and GPS). The RF interface has a 50 nominal impedance and a high DC impedance. 7.2.1 Frequency support Band Frequency Band 1 WCDMA 2100 Tx: 1920 ~ 1980 MHz Rx: 2110 ~ 2170 MHz Band 2 WCDMA 1900 Tx: 1850 ~ 1910 MHz Rx: 1930 ~ 1990 MHz Channel Number Tx: 9612-9888 Rx: 10562-1083 Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 27 of 42 TP825Q Product Specification
& Customer Design Guide Band 5 WCDMA 850 Tx: 824 ~ 849 MHz Rx: 869 ~ 894 MHz Tx: 824.2 ~ 849.2 MHz Rx: 869.2 ~ 894.2 MHz Tx: 880.0 ~ 915.0 MHz Rx: 925.0 ~ 960.0 MHz Tx: 1710.2 ~ 1784.8 MHz Rx: 1805.2 ~ 1879.8 MHz Tx: 1850.2 ~ 1909.8 MHz Rx: 1930.2 ~ 1989.8 MHz GSM 850 EGSM 900 DCS 1800 PCS 1900 Rev 1.4 Dec 20, 2013 128-251 795-1023, 0-124 512-885 512-810 7.2.2 Conducted Tx (Transmit) power tolerances Band Frequency Notes Band 1 (WCDMA 2100) Band 2 (WCDMA 1900) Band 5 (WCDMA 850) GSM 850 EGSM 900 DCS 1800 PCS 1900 Sensitivity
+23 dBm
+23 dBm
+23 dBm
+33 dBm
+33 dBm
+29 dBm
+29 dBm
<-104 dBm (FER 0.5%) 7.3 Wi-Fi + BT Parts Name Wi-Fi Description Maximum TX output: >+10 dBm Sensitivity:
IEEE 802.11g: 54 Mbps -65 dBm IEEE 802.11b/g: 11 Mbps -76 dBm Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 28 of 42 Rev 1.4 Dec 20, 2013 TP825Q Product Specification
& Customer Design Guide IEEE 802.11n: 20 Mbps -62 dBm Maximum permitted power (Class 2): -6 dBm < PAV < +4 dBm Modulation characteristics: 140 kHz f1avg 175 kHz Carrier frequency stability: -75 kHz i +75 kHz Maximum drift rate: 20 kHz/50 s Sensitivity: < -85 dBm (single-slot packet) BT 7.4 GPS Parts Characteristic Description TTF Cold Start: 32s Warm Start: 29s Hot Start: 1s Accuracy 10 m Sensitivity Tracking: -130 dB Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 29 of 42 TP825Q Product Specification
& Customer Design Guide 8. Power Consumption 8.1 System Power consumption ( with 7.9 TFT LCD ) Rev 1.4 Dec 20, 2013 Operating Mode Standby current Airplane mode WCDMA On (VBATT = 3.8V) GSM On (VBATT = 3.8V) WiFi Active only Bluetooth Active only Airplane mode (with LCD On) Shutdown current Work current Test 1#
Test 2#
Unit 4.38 8.62 6.3 5.35 4.72 4.47 8.76 6.5 4.81 4.74 548.20 548.60 0.008 0.008 mA mA mA mA mA mA mA WCDMA enable, with Internet Browsing 697.20 702.30 mA WCDMA enable, with Internet Video Streaming 1002.30 1005.30 mA Wi-Fi enable, with Internet Browsing Wi-Fi enable, with Internet Video Streaming Play MP3 via Speaker Play MP3 via Earphone Play MP3 via Bluetooth A2DP Voice via Bluetooth Battery voltage display
~ 100%
~ 85%
~ 71%
~ 57%
~ 43%
~ 28%
~ 15%
612.00 861.20 106.30 82.10 80.20 613.00 862.30 89.70 67.30 76.30 196.40 192.30 4.20 ~ 4.12 4.11 ~ 4.00 3.99 ~ 3.90 3.89 ~ 9.83 3.82 ~ 3.79 3.78 ~ 3.74 3.73 ~ 3.69 mA mA mA mA mA mA V V V V V V V Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 30 of 42 Rev 1.4 Dec 20, 2013 3.68 ~ 3.48 3.54 1.03 3.48 V V A V TP825Q Product Specification
& Customer Design Guide
~ 0%
Minimum power on voltage Minimum power on current Minimum work voltage 9. Soldered Solution and Mechanical Specifications 9.1 Recommended foot print for the Main application Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 31 of 42 TP825Q Product Specification
& Customer Design Guide Rev 1.4 Dec 20, 2013 Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 32 of 42 TP825Q Product Specification
& Customer Design Guide 9.2 Recommended foot print for the MIPI application Rev 1.4 Dec 20, 2013 9.2.1 PCB Reserve Area for MIPI interface This is an area recommended to reserve having a mechanical part on main or daughter PCB of module placement for MIPI interface application in direct contact with the module. Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 33 of 42 TP825Q Product Specification
& Customer Design Guide 9.2.2 Solder pad design for MIPI application The solder pad of MIPI interface definition on module:
Rev 1.4 Dec 20, 2013 Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 34 of 42 TP825Q Product Specification
& Customer Design Guide 9.3 PCB pad design Non solder mask defined (NSMD) type is recommended for the solder pads on the PCB. Rev 1.4 Dec 20, 2013 For manual soldering production, the proposed design of the edge of each pad will need to add the VIA, in order to prevent the pad tilt off. When connecting the pad to do with copper thermal design to prevent excessive cooling effect due to manual soldering efficiency. 9.4 Solder paste Recommended solder reflow profile:
Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 35 of 42 TP825Q Product Specification
& Customer Design Guide Solde reflow temperature profile reference table:
Profile Feature Average ramp-up rate (TL to TP) Preheat Temperature Min (Tsmin) Temperature Max (Tsmin) Time (min to max) (ts) Tsmax to TL Ramp-up Rate Time maintained above Temperature (TL) Time (tL) Peak Temperature (Tp) Time within 5 of actual Peak Temperature (tp) Rev 1.4 Dec 20, 2013 Pb-Free Assembly 150 220 70s - 110s 3C/second max. 217 30s-90s 245 +0/-5C
<40s Ramp-down Rate 6C/second max. Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 36 of 42 TP825Q Product Specification
& Customer Design Guide 9.5 Mechanical dimensions Rev 1.4 Dec 20, 2013 Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 37 of 42 TP825Q Product Specification
& Customer Design Guide 9.6 Labeling Rev 1.4 Dec 20, 2013 Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 38 of 42 TP825Q Product Specification
& Customer Design Guide 10. Certification Compliance and Recommended Standards Rev 1.4 Dec 20, 2013 10.1 Certification Compliance Domain CE FCC NCC Applicable Standard EN 300 328 EN 300 328 EN 300 440 EN 301 489-1/-3 EN 301 489-1/-7 EN 301 489-1/-24 EN 301 489-1&-17 EN 301 511 En 301 908-1 En 301 908-2 EN 62311 Part 15B Part 15C Part 22 Part 24 CNS 13438 CNS 14336 PLMN 01 PLMN 08 LP0002 10.2 Applicable Standards For queries concerning specific industry standards and certifications not described in this chapter, contact your TOUCHCOM account representative. 10.2.1 Important Notice Because of the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the TP825Q Embedded Module are used in a normal manner with a well-constructed network, the TP825Q Embedded Module should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. TP825Q Embedded Module and its affiliates accept no responsibility for damages of any kind resulting from delays or errors in Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 39 of 42 TP825Q Product Specification
& Customer Design Guide data transmitted or received using the TP825Q Embedded Module, or for failure of the TP825Q Embedded Module to transmit or receive such data. Rev 1.4 Dec 20, 2013 10.2.2 Safety and Hazards Do not operate your TP825Q Embedded Module modem:
In areas where blasting is in progress Where explosive atmospheres may be present including refuelling points, fuel depots, and chemical plants Near medical equipment, life support equipment, or any equipment which may be susceptible to any form of radio interference. In such areas, the TP825Q modem MUST BE POWERED OFF. Otherwise, the TP825Q modem can transmit signals that could interfere with this equipment. In an aircraft, the TP825Q modem MUST BE POWERED OFF. Otherwise, the TP825Q modem can transmit signals that could interfere with various onboard systems and may be dangerous to the operation of the aircraft or disrupt the cellular network. Use of a cellular phone in an aircraft is illegal in some jurisdictions. Failure to observe this instruction may lead to suspension or denial of cellular telephone services to the offender, or legal action or both. Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. The TP825Q modem may be used normally at this time. 10.2.3 Important Compliance Information for Unite America Users Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 40 of 42 TP825Q Product Specification
& Customer Design Guide This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter. FOR MOBILE DEVICE USAGE (>20cm/low power) Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Rev 1.4 Dec 20, 2013 This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users. 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID: 2ABC7TP825Q. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 10.2.4 EU Regulatory Conformity There is with confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility of Radio and Telecom device (1995/5/EC). Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 41 of 42 TP825Q Product Specification
& Customer Design Guide Rev 1.4 Dec 20, 2013 10.2.5 Important Compliance Information for Taiwan Users The type approved low power radio, permit, company, firm or user is not allowed to change the frequency, increase the power or change the features and functions of the original design. Low-power radio-frequency devices shall not influence aircraft security and interfere legal communications;
been found to have interference phenomenon, should be discontinued immediately, and until no interference is achieved continued use. In the preceding paragraph legal communications means operated in compliance with the Telecommunications Act radio communications. Low-power radio communications to endure legal or industrial, scientific and medical radio wave radiated interference of electrical equipment. Touchcom Wireless co.,Ltd. support@touchcom.tw WWW.TOUCHCOM.TW Page 42 of 42