| all | frequencies |
|
exhibits | applications |
|---|---|---|---|---|
| manual |
| app s | submitted / available | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 |
|
TD-W8901N(UN) UG REV1 | Users Manual | 2.07 MiB | August 04 2014 / September 04 2014 | |||
| 1 | Cover Letter(s) | August 04 2014 / September 04 2014 | ||||||
| 1 | Cover Letter(s) | August 04 2014 / September 04 2014 | ||||||
| 1 | Cover Letter(s) | August 04 2014 / September 04 2014 | ||||||
| 1 | External Photos | August 04 2014 / September 04 2014 | ||||||
| 1 | Test Report | August 04 2014 / September 04 2014 | ||||||
| 1 | Internal Photos | August 04 2014 / September 04 2014 | ||||||
| 1 | RF Exposure Info | August 04 2014 / September 04 2014 | ||||||
| 1 | Test Setup Photos | August 04 2014 / September 04 2014 | ||||||
| 1 | ID Label/Location Info | August 04 2014 / September 04 2014 |
| 1 | TD-W8901N(UN) UG REV1 | Users Manual | 2.07 MiB | August 04 2014 / September 04 2014 |
TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router Rev: 1.0.1 1910010775 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright 2014 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver Increase the separation between the equipment and receiver. is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1 This device may not cause harmful interference. 2 This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Limited to local law of the United States, selecting country code and channel function was disabled. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Canadian Compliance Statement exempt RSS standard(s). Operation is subject This device complies with Industry Canada license-
to the following two conditions:
(1) This device may not cause int erference, and
(2)This device must accept any interference, inc operation of the device. Cet appareil est confo fonctionnement est soumis aux deux conditions suivantes:
(1) cet appareil ne doit pas provoquer dinterfrences et
(2) cet appareil doit accepter toute interfrence, y compr fonctionnement non souhait de lappareil. luding interference that may cause undesired rme aux norms CNR exemptes de licence dIndustrie Canada. Le is celles susceptibles de provoquer un e antennas listed below, and having a maximum This device has been designed to operate with th gain of 5 dBi. Antennas not included in this list or having a gain greater than 5 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. Industry Canada Statement cifications. Complies with the Canadian ICES-003 Class B spe Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device mee requirements of the Canadian interference-causing equipment regulations. Cet appareil numrique de la Classe B respecte toutes les exigences matriel brouilleur du Canada. ts all the du Rglement sur le Korea Warning Statements
. NCC Notice & BSMI Notice UkrSEPRO
,
. Safety Information When product has power button, the power button is one of the way to shut off the product;
when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Dont disassemble the product, or make repairs your self. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. Avoid water and wet locations. This product can be used in the following countries:
AT ES LT RU BG FI LV SE BY FR MT SK CA GB NL TR CZ GR NO UA DE HU PL DK IE PT EE IT RO TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment:
Product Description: 150Mbps Wireless N ADSL2+ Modem Router Model No.: TD-W8901N Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives:
Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC, Directives 2011/65/EU The above product is in conformity with the following standards or other normative documents ETSI EN 300 328 V1.7.1: 2006 ETSI EN 301 489-1 V1.9.2:2011& ETSI EN 301 489-17 V2.2.1:2012 EN 55022:2010 EN 55024:2010 EN 61000-3-2:2006+A1:2009+A2:2009 EN 61000-3-3:2008 EN 60950-1:2006+A112009+A1:2010+A12:2011 EN 62311:2008 The product carries the CE Mark:
Person responsible for making this declaration:
Yang Hongliang Product Manager of International Business TP-LINK TECHNOLOGIES CO., LTD. Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China Date of issue: 2014 CONTENTS Package Contents .................................................................................................... 1 Introduction......................................................................................... 2 Chapter 1. 1.1 Product Overview........................................................................................... 2 1.2 Main Features ................................................................................................ 2 1.3 Conventions ................................................................................................... 3 Chapter 2. Hardware Installation ......................................................................... 4 2.1 The Front Panel ............................................................................................. 4 2.2 The Back Panel.............................................................................................. 5 2.3 Installation Environment................................................................................. 6 2.4 Connecting the Modem Router ...................................................................... 7 Chapter 3. Quick Installation Guide..................................................................... 9 3.1 Configure PC ................................................................................................. 9 3.2 Login ............................................................................................................ 12 Chapter 4. Software Configuration .................................................................... 16 4.1 Status........................................................................................................... 16 4.1.1 Device Info ..............................................................................................................16 4.1.2 System Log .............................................................................................................17 4.1.3 Statistics..................................................................................................................18 4.2 Quick Start ................................................................................................... 20 Interface Setup............................................................................................. 21 4.3 4.3.1 Internet....................................................................................................................21 4.3.2 LAN .........................................................................................................................26 4.3.3 Wireless ..................................................................................................................30 4.4 Advanced Setup........................................................................................... 41 4.4.1 Firewall....................................................................................................................41 4.4.2 Routing....................................................................................................................42 4.4.3 NAT.........................................................................................................................43 4.4.4 QoS.........................................................................................................................46 4.4.5 VLAN.......................................................................................................................49 4.4.6 ADSL.......................................................................................................................51 4.5 Access Management.................................................................................... 52 4.5.1 ACL .........................................................................................................................52 4.5.2 Filter ........................................................................................................................53 4.5.3 SNMP......................................................................................................................62 4.5.4 UPnP.......................................................................................................................62 4.5.5 DDNS......................................................................................................................63 4.5.6 CWMP.....................................................................................................................64 4.6 Maintenance ................................................................................................ 65 4.6.1 Administration .........................................................................................................65 4.6.2 Time Zone...............................................................................................................66 4.6.3 Firmware .................................................................................................................67 4.6.4 SysRestart ..............................................................................................................70 4.6.5 Diagnostics .............................................................................................................70 4.7 Help.............................................................................................................. 71 Appendix A: Specifications ................................................................................... 73 Appendix B: Troubleshooting ............................................................................... 74 Appendix C: Technical Support ............................................................................ 77 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Package Contents The following contents should be found in your package:
One TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router One Power Adapter for TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router Quick Installation Guide One RJ45 cable Two RJ11 cables One ADSL splitter (Optional) One Resource CD, which includes this User Guide Note:
Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact your distributor. 1 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 1. Introduction Thank you for choosing the TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router. 1.1 Product Overview The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet or IEEE 802.11n/ IEEE 802.11g/ IEEE 802.11b wireless network. The TD-W8901N connects to an Ethernet LAN or computers via standard Ethernet ports. The ADSL connection is made using ordinary telephone line with standard connectors. Multiple workstations can be networked and connected to the Internet using a single Wide Area Network
(WAN) interface and single global IP address. The advanced security enhancements, IP/MAC Filter, Application Filter and URL Filter can help to protect your network from potentially devastating intrusions by malicious agents from the outside of your network. Quick Start of the Web-based Utility is supplied and friendly help messages are provided for the configuration. Network and Router management is done through the Web-based Utility which can be accessed through local Ethernet using any web browser. ADSL The TD-W8901N supports full-rate ADSL2+ connectivity conforming to the ITU and ANSI specifications. In addition to the basic DMT physical layer functions, the ADSL2+ PHY supports dual latency ADSL2+ framing (fast and interleaved) and the I.432 ATM Physical Layer. Wireless In the most attentive wireless security, the Router provides multiple protection measures. It can be set to turn off the wireless network name (SSID) broadcast so that only stations that have the SSID can be connected. The Router provides wireless LAN 64/128-bit WEP encryption security, WPA-PSK/WPA2-PSK authentication, as well as TKIP/AES encryption security. 1.2 Main Features Four 10/100Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/MDIX), one RJ11 port. Provides external splitter. Adopts Advanced DMT modulation and demodulation technology. Supports bridge mode and Router function. Multi-user sharing a high-speed Internet connection. Downstream data rates up to 24Mbps, upstream data rates up to 3.5MbpsWith Annex M enabled. 2 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Supports long transfers, the max line length can reach to 6.5Km. Supports remote configuration and management through SNMP and CWMP. Supports PPPoE, it allows connecting the internet on demand and disconnecting from the Internet when idle. Provides reliable ESD and surge-protect function with quick response semi-conductive surge protection circuit. High speed and asymmetrical data transmit mode, provides safe and exclusive bandwidth. Supports All ADSL industrial standards. Compatible with all mainstream DSLAM (CO). Provides integrated access of internet and route function which face to SOHO user. Real-time Configuration and device monitoring. Supports Multiple PVC (Permanent Virtual Circuit). Built-in DHCP server. Built-in firewall, supporting IP/MAC filter, Application filter and URL filter. Supports Virtual Server, DMZ host and IP Address Mapping. Supports Dynamic DNS, UPnP and Static Routing. Supports system log and flow Statistics. Supports firmware upgrade and Web management. Provides WPA-PSK/WPA2-PSK data security, TKIP/AES encryption security. Provides 64/128-bit WEP encryption security and wireless LAN ACL (Access Control List). 1.3 Conventions The Router or device mentioned in this User Guide stands for TD-W8901N without any explanations. Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation. 3 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 2. Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs locate on the front panel. They indicate the devices working status. For details, please refer to LED Explanation. LED Explanation:
Status Indication On Name
(Power)
(ADSL)
(Internet) Off On Flash Off On Flash Off On
(WLAN) Flash Off On Flash Off
(LAN 1-4) Note:
The modem router is powered on. The modem router is off. Please ensure that the power adapter is connected correctly. ADSL line is synchronized and ready to use. The ADSL negotiation is in progress. ADSL synchronization fails. Please refer to Note 1 for troubleshooting. The network is available with a successful Internet connection. There is data being transmitted or received via the Internet. There is no successful Internet connection or the modem router is operating in Bridge mode. Please refer to Note 2 for troubleshooting. Wireless is enabled but no data is being transmitted. The modem router is sending or receiving data over the wireless network. Wireless function is disabled. There is a device connected to this LAN port. The modem router is sending or receiving data over this LAN port. There is no device connected to this LAN port. 1. 2. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting the Modem Router for more information about how to make Internet connection correctly. If you have already made a right connection, please contact your ISP to make sure if your Internet service is available now. If the Internet LED is off, please check your ADSL LED first. If your ADSL LED is also off, please refer to Note 1. If your ADSL LED is GREEN ON, please check your Internet configuration. You may need to check this part of information with your ISP and make sure 4 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide everything have been input correctly. Refer to 4.1.1 Device Info and 4.3.1 Internet for more information. 2.2 The Back Panel POWER: The Power plug is where you will connect the power adapter. Figure 2-2 ON/OFF: The switch for the power. WiFi: Press this button to enable or disable Wireless LAN interface. RESET: There are two ways to reset the Router's factory defaults. Method one: With the Router powered on, use a pin to press and hold the Reset button for at least 5 seconds. And the Router will reboot to its factory default settings. Method two: Restore the default setting from Maintenance-SysRestart of the Router's Web-based Utility. 1, 2, 3, 4 (LAN): Through the port, you can connect the Router to your PC or the other Ethernet network devices. 5 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide ADSL: Through the port, you can connect the router with the telephone. Or you can connect them by an external separate splitter. For details, please refer to 2.4 Connecting the Modem Router. Antenna: Used for wireless operation and data transmit. 2.3 Installation Environment The Product should not be located where it will be exposed to moisture or excessive heat. Place the Router in a location where it can be connected to the various devices as well as to a power source. Make sure the cables and power cord are safely placed out of the way so they do not create a tripping hazard. The Router can be placed on a shelf or desktop. Keep away from the strong electromagnetic radiation and the device of electromagnetic sensitive. Figure 2-3 Wall-mount Install Note:
The diameter of the screw, 3.5mm<D<8mm, and the distance of two screws is 118mm. The screw that project from the wall need around 4mm based, and the length of the screw need to be at least 20mm to withstand the weight of the product. 6 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 2.4 Connecting the Modem Router Before installing the device, please make sure your broadband service provided by your ISP is available. If there is any problem, please contact your ISP. Before cable connection, cut off the power supply and keep your hands dry. You can follow the steps below to install it. Step 1: Connect the ADSL Line. Method one: Plug one end of the twisted-pair ADSL cable into the ADSL port on the rear panel of TD-W8901N, and insert the other end into the wall socket. Method twoYou can use a separate splitter. External splitter can divide the data and voice, and then you can access the Internet and make calls at the same time. The external splitter has three ports:
LINE: Connect to the wall jack PHONE: Connect to the phone sets MODEM: Connect to the ADSL port of TD-W8901N Plug one end of the twisted-pair ADSL cable into the ADSL port on the rear panel of TD-W8901N. Connect the other end to the MODEM port of the external splitter. Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computers Ethernet port or a regular hub/switch port, and the other end to the LAN port on the TD-W8901N. Step 3: Power on the computers and LAN devices. Step 4: Attach the power adapter. Connect the power adapter to the power connector on the rear of the device and plug in the adapter to a electrical outlet or power extension. The electrical outlet shall be installed near the device and shall be easily accessible. 7 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 2-4 8 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 3. Quick Installation Guide 3.1 Configure PC After you directly connect your PC to the TD-W8901N or connect your adapter to a Hub/Switch which has connected to the Router, you need to configure your PCs IP address. Follow the steps below to configure it. Step 1: Click the Start menu on your desktop, right click My Network Places, and then select Properties (shown in Figure 3-1). Figure 3-1 Step 2: Right click Local Area Connection (LAN), and then select Properties. 9 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties button. Figure 3-3 10 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK. Figure 3-4 Note:
You can configure the PC to get an IP address automatically, select Obtain an IP address automatically and Obtain DNS server address automatically in the screen above. Now, you can run the Ping command in the command prompt to verify the network connection. Please click the Start menu on your desktop, select run tab, type cmd or command in the field and press Enter. Type ping 192.168.1.1 on the next screen, and then press Enter. If the result displayed is similar to the screen below, the connection between your PC and the Router has been established. 11 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-5 If the result displayed is similar to the screen shown below, it means that your PC has not connected to the Router. You can check it following the steps below:
Figure 3-6 1) Is the connection between your PC and the Router correct?
The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. Is the TCP/IP configuration for your PC correct?
2) If the Router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254. 3.2 Login Once your host PC is properly configured, please proceed as follows to use the Web-based Utility:
Start your web browser and type the private IP address of the Router in the URL field: 192.168.1.1. After that, you will see the screen shown below, enter the default User Name admin and the default Password admin, and then click OK to access to the Quick Start screen. You can follow the steps below to complete the Quick Start. 12 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button. Figure 3-7 Step 2: Configure the time for the Router, and then click the NEXT button. Figure 3-8 Step 3: Select the connection type to connect to the ISP (We select PPPoE/PPPoA mode for example here), and then click the NEXT button. Figure 3-9 13 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 4: Configure the following options provided by your ISP: Username, Password, VPI, VCI and Connection Type. Then click NEXT. Figure 3-10 Step 5: Configure the rules for the WLAN, and click NEXT. Figure 3-11 14 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 3-12 Note:
If the Access Point is activated, the wireless function will be available even without the external antenna because of an additional printed antenna. To adopt the wireless security protection measures, please refer to 4.3.3 Wireless. Step 6: Click NEXT to finish the Quick Start. Figure 3-13 15 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 4. Software Configuration This User Guide recommends using the Quick Installation Guide for first-time installation. For advanced users, if you want to know more about this device and make use of its functions adequately, maybe you will get help from this chapter to configure the advanced settings through the Web-based Utility. After your successful login, you can configure and manage the device. There are main menus on the top of the Web-based Utility; submenus will be available after you click one of the main menus. On the center of the Web-based Utility, there are the detailed configurations or status information. To apply any settings you have altered on the page, please click the SAVE button. 4.1 Status Choose Status, you can see the next submenus: Device Info, System Log and Statistics. Click any of them, and you will be able to configure the corresponding function. Figure 4-1 Click any of them, and you will be able to view the corresponding information. 4.1.1 Device Info Choose StatusDevice Info menu, and you will be able to view the device information, including LAN, WAN and ADSL. The information will vary depending on the settings of the Router configured on the Interface Setup screen. 16 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-2 Note:
Click the other submenus System Log or Statistics in Figure 4-2, and you will be able to view the system log and traffic statistics about the Router. 4.1.2 System Log Choose StatusSystem Log menu, and you will be able to query the logs of the Router. 17 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-3 The Router can keep logs of all traffic. You can query the logs to find what happened to the Router. Click the CLEAR LOG button to clear the logs. Click the SAVE LOG button to save the logs. 4.1.3 Statistics Choose StatusStatistics menu, and you will be able to view the network traffic over Ethernet, ADSL and WLAN. 18 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-4 Interface: You can select Ethernet, ADSL and WLAN to view the corresponding network traffic over different ports. Select Ethernet, and you will see the statistics table as below. Statistics Table:
Transmit Statistics Receive Statistics Transmit Frames The frames transmitted over the Ethernet port. Transmit Multicast Frames The multicast frames transmitted over the Ethernet port. Transmit total Bytes The total bytes transmitted over the Ethernet port. Transmit Collision The collision occurred over the Ethernet port when data is being transmitted. Transmit Error Frames The error frames over the Ethernet port when data is being transmitted. Receive Frames The frames received over the Ethernet port. Receive Multicast Frames The multicast frames received over the Ethernet port. Receive total Bytes The total bytes received over the Ethernet port. Receive CRC Errors The CRC errors occurred over the Ethernet port when data is being received. Receive Under-size Frames The Under-size frames received over the Ethernet port. 19 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Select ADSL, and you will see the statistics table as below. Statistics Table:
Transmit total PDUs Transmit Statistics Transmit total Error Counts Receive total PDUs Receive Statistics Receive total Error Counts The total PDUs transmitted over the ADSL port. The total errors occurred over the ADSL port when data is being transmitted. The total PDUs transmitted over the ADSL port. The total errors occurred over the ADSL port when data is being received. Select WLAN, and you will see the statistics table as below. Statistics Table:
Tx Frames Count The frames transmitted over the WLAN when wireless data is being transmitted. Transmit Statistics Tx Errors Count The errors occurred over the WLAN when wireless data is being transmitted. Tx Drops Count The drops occurred over the WLAN when wireless data is being transmitted. Rx Frames Count The frames received over the WLAN when wireless data is being transmitted. Receive Statistics Rx Errors Count The errors occurred over the WLAN when wireless data is being received. Rx Drops Count The drops occurred over the WLAN when wireless data is being received. Click the REFRESH button to refresh immediately. 4.2 Quick Start Please refer to 3.2 Login. 20 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Interface Setup 4.3 Choose Interface Setup, you can see the next submenus: Internet, LAN and Wireless. Figure 4-5 Click any of them, and you will be able to configure the corresponding function. 4.3.1 Internet Choose Interface SetupInternet menu, you can configure the parameters for WAN ports in the next screen (shown in Figure 4-6). 21 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-6 ATM VC: ATM settings are used to connect to your ISP. Your ISP provides VPI (Virtual Path Identifier), VCI (Virtual Channel Identifier) settings to you. In this Device, you can totally setup 8 VCs on different encapsulations, if you apply 8 different virtual circuits from your ISP. You need to activate the VC to take effect. For PVCs management, you can use ATM QoS to setup each PVC traffic line's priority. Virtual Circuit: Select the VC number you want to setup, PVC0~PVC7. 22 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Status: If you want to use a designed VC, you should activate it. VPI: Identifies the virtual path between endpoints in an ATM network. The valid range is from 0 to 255. Please input the value provided by your ISP. VCI: Identifies the virtual channel endpoints in an ATM network. The valid range is from 32 to 65535 (1 to 31 is reserved for well-known protocols). Please input the value provided by your ISP. PVCs Summary: Click the button, and you can view the summary information about the PVCs. QoS: Select the Quality of Service types for this Virtual Circuit, including CBR (Constant Bit Rate), UBR (Unspecified Bit Rate) and VBR (Variable Bit Rate). These QoS types are all controlled by the parameters specified below, including PCR (Peak Cell Rate), SCR
(Sustained Cell Rate) and MBS (Maximum Burst Size), please configure them according to your needs. Encapsulation: There are four connection types: Dynamic IP Address, Static IP Address, PPPoA/PPPoE and Bridge Mode. Please choose the designed type that you want to use. After that, you should follow the configuration below to proceed. 4.3.1.1 Dynamic IP Address Select this option if your ISP provides you an IP address automatically. This option is typically used for Cable services. Please enter the Dynamic IP information accordingly. Figure 4-7 Encapsulation: Select the encapsulation mode for the Dynamic IP Address, you can leave it default. NAT: Select this option to Enable/Disable the NAT (Network Address Translation) function for this VC. The NAT function can be activated or deactivated per PVC basis. 23 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Default Route: If enable this function, the current PVC will be considered as the default gateway to internet from this device. TCP MTU Option: Enter the TCP MTU as your desire. Dynamic Route: Select this option to specify the RIP (Routing Information protocol) version for WAN interface, including RIP1, RIP2-B and RIP2-M. RIP2-B and RIP2-M are both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format. Direction: Select this option to specify the RIP direction. None is for disabling the RIP function. Both means the ADSL Router will periodically send routing information and accept routing information, and then incorporate them into routing table. IN only means the ADSL Router will only accept but will not send RIP packet. OUT only means the ADSL Router will only send but will not accept RIP packet. Multicast: Select IGMP version, or disable the function. IGMP (Internet Group Multicast Protocol) is a session-layer protocol used to establish membership in a multicast group. The ADSL ATU-R supports IGMP version 1 (IGMP v1), IGMP v2 and IGMP v3. Select Disabled to disable it. 4.3.1.2 Static IP Address Select this option if your ISP provides static IP information to you. You should set static IP address, IP subnet mask, and gateway address in the screen below (shown in Figure 4-8). Figure 4-8 24 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Note:
Each IP address entered in the fields must be in the appropriate IP form, which is four IP octets separated by a dot (x.x.x.x), such as 192.168.1.100. The Router will not accept the IP address if it is not in this format. 4.3.1.3 PPPoA/PPPoE Select this option if your ISP requires you to use a PPPoE connection. This option is typically used for DSL services. Select Dynamic PPPoE to obtain an IP address automatically for your PPPoE connection. Select Static PPPoE to use a static IP address for your PPPoE connection. Please enter the information accordingly. Figure 4-9 Servicename: Enter a name to mark current connection, or you can leave it blank. Username: Enter your username for your PPPoA/PPPoE connection. Password: Enter your password for your PPPoA/PPPoE connection. 25 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Encapsulation: For both PPPoA/PPPoE connection, you need to specify the type of Multiplexing, either LLC or VC Mux. Bridge Interface: Activate the option, and the Router can also work in Bridge mode. Connection: For PPPoA/PPPoE connection, you can select Always on or Connect on-Demand or Connect Manually. Connect on demand is dependent on the traffic. If there is no traffic (or Idle) for a pre-specified period of time), the connection will tear down automatically. And once there is traffic send or receive, the connection will be automatically on. Static/Dynamic IP Address: For PPPoA/PPPoE connection, you need to specify the public IP address for this ADSL Router. The IP address can be either dynamically (via DHCP) or given IP address provided by your ISP. For Static IP, you need to specify the IP address, Subnet Mask and Gateway IP address. Default Route: You should select Yes to configure the PVC as the default gateway to internet from this device. 4.3.1.4 Bridge Mode If you select this type of connection, the modem router can be configured to act as a bridging device between your LAN and your ISP. Bridges are devices that enable two or more networks to communicate as if they are two segments of the same physical LAN. Figure 4-10 Note:
After you finish the Internet configuration, please click SAVE to make the settings take effect. 4.3.2 LAN Choose Interface SetupLAN menu, and you will see the LAN screen (shown in Figure 4-11). Please configure the parameters for LAN ports according to the descriptions below. 26 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-11 Router Local IP: These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet. IP Address: Enter the Routers local IP Address, then you can access to the Web-based Utility via the IP Address, the default value is 192.168.1.1. IP Subnet Mask: Enter the Routers Subnet Mask, the default value is 255.255.255.0. Dynamic Route: Select this option to specify the RIP (Routing Information protocol) version for LAN interface, including RIP1, RIP2-B and RIP2-M. RIP2-B and RIP2-M are both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format. Direction: Select this option to specify the RIP direction. None is for disabling the RIP function. Both means the ADSL Router will periodically send routing information and accept routing information, and then incorporate them into routing table. IN only means the ADSL Router will only accept but will not send RIP packet. OUT only means the ADSL Router will only send but will not accept RIP packet. 27 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Multicast: Select IGMP version, or disable the function. IGMP (Internet Group Multicast Protocol) is a session-layer protocol used to establish membership in a multicast group. The ADSL ATU-R supports IGMP version 1 (IGMP v1), IGMP v2 and IGMP v3. Select Disabled to disable it. IGMP Snoop: Enable the IGMP Snoop function if you need. DHCP Server: Select Enabled, then you will see the screen below (shown in Figure 4-12). The Router will work as a DHCP Server; it becomes the default gateway for DHCP client connected to it. DHCP stands for Dynamic Host Control Protocol. The DHCP Server gives out IP addresses when a device is booting up and request an IP address to be logged on to the network. That device must be set as a DHCP client to obtain the IP address automatically. By default, the DHCP Server is enabled. The DHCP address pool contains the range of the IP address that will automatically be assigned to the clients on the network. Figure 4-12 Starting IP Address: Enter the starting IP address for the DHCP server's IP assignment. Because the default IP address for the Router is 192.168.1.1, the default Start IP Address is 192.168.1.100, and the Start IP Address must be 192.168.1.100 or greater, but smaller than 192.168.1.254. IP Pool Count: The max user pool size. Lease Time: The length of time for the IP lease. After the dynamic IP address has expired, the user will be automatically assigned a new dynamic IP address. The default is 259200 seconds. Physical Ports: If a physical port is unchecked, the client connected to that port will not 28 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide be able to obtain IP address automatically although the DHCP function is enabled. All the ports are checked by default. DHCP Table: The information of the DHCP clients will be displayed here IP Address: Display the IP Address of the DHCP client. Hostname: Display the name of the DHCP client. MAC Address: Display the MAC Address of the DHCP client. Status: Display the status of the assigned IP Address, either Static or Auto. Static indicates that the IP Address is bounded to the MAC Address, while Auto indicates that the IP Address is assigned to the MAC Address automatically. How to assign a static IP address to the client?
1). Select an IP Address from the drop-down list. 2). Enter the MAC Address of the client in the table. DNS Relay: If you want to disable this feature, you just need to set both Primary and secondary DNS IP to 0.0.0.0. If you want to use DNS relay, you can setup DNS server IP to 192.168.1.1 on their Computer. If not, the device will perform as no DNS relay. Primary DNS Server: Type in your preferred DNS server. Secondary DNS Server: Type in your preferred DNS server. Note:
If Use Auto Discovered DNS Server Only is selected in DNS Relay, this router will accept the first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s) during the connection establishment. If Use User Discovered DNS Server Only is selected in DNS Relay, it is necessary for you to enter the primary and optional secondary DNS server IP addresses. After type in the address, click SAVE button to save it and invoke it. DHCP Relay: Select Relay, then you will see the next screen (shown in Figure 4-13), and the Router will work as a DHCP Relay. A DHCP relay is a computer that forwards DHCP data between computers that request IP addresses and the DHCP server that assigns the addresses. Each of the device's interfaces can be configured as a DHCP relay. If it is enabled, the DHCP requests from local PCs will forward to the DHCP server runs on WAN side. To have this function working properly, please run on router mode only, disable the DHCP server on the LAN port, and make sure the routing table has the correct routing entry. 29 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide DHCP Server IP for Relay Agent: Enter the DHCP server IP Address runs on WAN Figure 4-13 side. Note:
If you select Disabled, the DHCP function will not take effect. 4.3.3 Wireless Choose Interface SetupWireless menu, and you will see the Wireless screen (shown in Figure 4-14 ). Please configure the parameters for wireless according to the descriptions below. 30 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-14 31 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Access point Settings: These are the settings of the access point. You can configure the rules to allow wireless-equipped computers and other devices to communicate with a wireless network. Access point: Select Activated to allow wireless station to associate with the access point. Transmit Power: Here you can specify the transmit power of Router. You can select High, Medium or Low which you would like. High is the default setting and is recommended. Beacon Interval: Enter a value between 20-1000 milliseconds. The Beacon Interval value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the Router to synchronize the wireless network. The default value is 100. RTS/CTS Threshold: Should you encounter inconsistent data flow, only minor reduction of the default value 2347 is recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. The Router sends Request to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge the right to begin transmission. In most cases, keep its default value of 2347. Fragmentation Threshold: This value specifies the size for a packet. When packet size exceeds the fragmentation threshold, the packet will be fragmented into multiple packets. Setting the Fragmentation Threshold too low may result in poor network performance. In most cases, it should remain at its default value of 2346. DTIM: This value, between 1 and 255, indicates the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the Router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. Its clients hear the beacons and awaken to receive the broadcast and multicast messages. The default value is 1. Wireless Mode: In the drop-down list you can select 802.11b, 802.11g, 802.11n, 802.11b+g, 802.11g+n and 802.11b+g+n. 802.11b+g+n allows 802.11b, 802.11g and 802.11n wireless stations to connect to the Router. 32 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 11n Settings: These are the settings of the 11n parameters. If 802.11n, 802.11g+n or 802.11b+g+n is selected for Wireless mode, these settings will be displayed. Channel Bandwidth: Select the Bandwidth you want to use from the drop-down List. There are two options, 20 MHz and 20/40 MHz. If bigger bandwidth is selected, device could transmit and receive data with higher speed. Extension Channel: If 20/40 MHz is selected, this option will be displayed. Guard Interval: Select the guard interval you want from the drop-down list. MCS: Select the wireless transmission rate from the drop-down list. By default, the option is AUTO. Multiple SSIDs Settings: These are the settings of the SSID. SSID Index: The index of the SSID, and in this model, you can only leave it as a default value of 1. Broadcast SSID: When wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the Router. To broadcast the Routers SSID, keep the default setting. If you dont want to broadcast the Routers SSID, select No. Use WPS: Use WPS (Wi-Fi Protected Setup) function, you can add a new wireless device to an existing network quickly. To Use WPS, keep the default setting, and configure the parameters in WPS Settings. If you dont want to Use WPS, select No, then you will see the screen as shown below. Figure 4-15 SSID: Wireless network name shared among all points in a wireless network. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters (use any of the characters on the keyboard). Make sure this setting is the same for all stations in your wireless network. Type the desired SSID in the space provided. Authentication Type: Select an authentication type from the drop-down list, which allows you to configure security features of the wireless LAN interface. Options available are: Disabled, WEP-64Bits, WEP-128Bits, WPA-PSK, WPA2-PSK, and WPA-PSK/
WPA2-PSK. 33 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 1) WEP-64Bits To configure WEP-64Bits settings, select the WEP-64Bits option from the drop-down list. The menu will change to offer the appropriate settings. WEP-64Bits is a data privacy mechanism based on a 64-bit shared key algorithm, as described in the IEEE 802.11g standard. Figure 4-16 2) WEP-128Bits To configure WEP-128Bits settings, select the WEP-128Bits option from the drop-down list. The menu will change to offer the appropriate settings. 128-bit is stronger than 64-bit. Figure 4-17 3) WPA-PSK To configure WPA-PSK settings, select the WPA-PSK option from the drop-down list. The menu will change to offer the appropriate settings. WPA-PSK requires a shared key and does not use a separate server for authentication. PSK keys can be ASCII or Hex type. 34 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-18 Encryption: Select the encryption you want to use: TKIP/AES, TKIP or AES (AES is an encryption method stronger than TKIP). TKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for each packet transmitted. AES (Advanced Encryption Standard) - A security method that uses symmetric 128-bit block data encryption. Pre-Shared Key: Enter the key shared by the Router and your other network devices. It must have 8-63 ASCII characters or 64 Hexadecimal digits. 4) WPA2-PSK To configure WPA2-PSK settings, select the WPA2-PSK option from the drop-down list. The menu will change to offer the appropriate settings. WPA2-PSK requires a shared key and does not use a separate server for authentication. PSK keys can be ASCII or Hex type. Figure 4-19 5) WPA-PSK/WPA2-PSK To configure WPA-PSK/WPA2-PSK settings, select the WPA-PSK/WPA2-PSK option from the drop-down the appropriate settings. WPA-PSK/WPA2-PSK requires a shared key and does not use a separate server for authentication. PSK keys can be ASCII or Hex type. WPA-PSK/WPA2-PSK is more flexible than WPA-PSK or WPA2-PSK. list. The menu will change to offer 35 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.3.3.1 WPS Settings Figure 4-20 WPS Settings: WPS can help you to add a new wireless device to an existing network quickly. This section will guide you how to use WPS function. WPS state: Display the current WPS state. WPS mode: If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and Router using either Push Button Configuration (PBC) method or PIN method, please select the one you want. WPS progress: Show the current WPS progress. Reset to OOB: Use this button to reset the WPS state to unconfigured, so that a new key will be created when using WPS function next time. 1) PBC If the wireless adapter supports Wi-Fi Protected Setup and the Push Button Configuration
(PBC) method, you can add it to the network by PBC with the following two methods. Click PBC, you will see the screen as shown below. Figure 4-21 Method One:
Step 1: Click Start WPS button in Figure 4-21. Step 2: Press and hold the WPS button of the adapter directly for 2 or 3 seconds. Step 3: Wait for a while until the next screen appears. Click Finish to complete the WPS configuration. 36 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide The WPS Configuration Screen of Wireless Adapter Method Two:
Step 1: Click Start WPS button in Figure 4-21. Step 2: For the configuration of the wireless adapter, please choose Push the button on my access point in the configuration utility of the WPS as below, and click Next. The WPS Configuration Screen of Wireless Adapter 37 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 3: Wait for a while until the next screen appears. Click Finish to complete the WPS configuration. The WPS Configuration Screen of Wireless Adapter 2) PIN code If the wireless adapter supports Wi-Fi Protected Setup and the PIN method, you can add it to the network by PIN with the following two methods. Click PIN code, you will see the screen as shown below. Figure 4-22 Method One: Enter the PIN into my Router Step 1: For the configuration of the wireless adapter, please choose Enter a PIN into my access point or a registrar in the configuration utility of the WPS, and get the PIN code on the screen as below, then click Next. 38 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide The WPS Configuration Screen of Wireless Adapter Step 2: For the Router, keep PIN code selected and enter the PIN code of the wireless adapter in the field after enrollee PIN code as shown below. Then click Start WPS. Figure 4-23 Method Two: Enter the PIN from my Router Step 1: Get the Current PIN code of the Router from AP self PIN code in Figure 4-23 (each Router has its unique PIN code. Here takes the PIN code 00001557 of this Router for example). Step 2: For the configuration of the wireless adapter, please choose Enter a PIN from my access point in the configuration utility of the WPS as below, and enter the PIN code of the Router into the field after Access Point PIN. Then click Next. 39 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide The WPS Configuration Screen of Wireless Adapter Note:
The default PIN code of the Router can be found in its label or the WPS configuration screen as Figure 4-23. SSID: Wireless network name shared among all points in a wireless network. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters (use any of the characters on the keyboard). Make sure this setting is the same for all stations in your wireless network. Type the desired SSID in the space provided. Authentication Type: Select an authentication type from the drop-down list, which allows you to configure security features of the wireless LAN interface. Options available are: Disabled, WEP-64Bits, WEP-128Bits, WPA-PSK, WPA2-PSK, and WPA-PSK/
WPA2-PSK. WDS Settings: Select On/Off to enable/disable WDS. With this function enabled, the Router can bridge two or more WLANs. MAC Address: Enter the MAC Address you wish to bridge in the field. Wireless MAC Address Filter: Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your networks RADIUS. Active: If you wish to filter users by MAC Address, select Activated, and Deactived for dont. Action: To filter wireless users by MAC Address, select Allow Association or Deny Association the follow Wireless LAN station(s) association. 40 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide MAC Address: Enter the MAC Address you wish to filter in the field. Note:
For most users, it is recommended to use the default Wireless LAN Performance settings. Any changes made to these settings may adversely affect your wireless network. Under certain circumstances, changes may benefit performance. Carefully consider and evaluate any changes to these wireless settings. 4.4 Advanced Setup Choose Advanced Setup, you can see the next submenus:
Click any of them, and you will be able to configure the corresponding function. Figure 4-24 4.4.1 Firewall Choose Advanced SetupFirewall menu, and you will see the next screen (shown in Figure 4-25). Figure 4-25 Firewall: Select this option can automatically detect and block Denial of Service (DoS) attacks, such as Ping of Death, SYN Flood, Port Scan and Land Attack. SPI: If you enable SPI, all traffics initiated from WAN would be blocked, including DMZ, Virtual Server, and ACL WAN side. 41 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.2 Routing Choose Advanced SetupRouting menu, and you will see the routing information in the next screen (shown in Figure 4-26). Click ADD ROUTE button to add a new route in the next screen (shown in Figure 4-27). Figure 4-26 Destination IP Address: This parameter specifies the IP network address of the final Figure 4-27 destination. IP Subnet Mask: Enter the subnet mask for this destination. Gateway IP Address: Enter the IP address of the gateway. The gateway is an immediate neighbor of your ADSL Router that will forward the packet to the destination. On the LAN, the gateway must be a router on the same segment as your Router; over Internet (WAN), the gateway must be the IP address of one of the remote nodes. Metric: Metric represents the "cost" of transmission for routing purposes. IP Routing uses hop count as the measurement of cost, with a minimum of 1 for directly connected networks. Enter a number that approximates the cost for this link. The number need not to be precise, but it must between 1 and 15. In practice, 2 or 3 is usually a good number. Announced in RIP: This parameter determines if the ADSL Router will include the route to this remote node in its RIP broadcasts. If set to Yes, the route to this remote node will be propagated to other hosts through RIP broadcasts. If No, this route is kept private and is not included in RIP broadcasts. 42 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.3 NAT Choose Advanced SetupNAT menu, you can setup the NAT (Network Address Translation) function for the Router (shown in Figure 4-28). Note:
To use the NAT function, the Virtual Circuit should not be configured to Bridge mode. You can change the mode in Figure 4-6. Figure 4-28 Virtual Circuit: Enter Virtual Circuit Index that you plan to setup for the NAT function. NAT Status: This field shows the current status of the NAT function for the current VC. You can go to the previous screen (shown in Figure 4-6) to activate the function. Number of IPs; This field is to specify how many IPs are provided by your ISP for current VC. It can be single IP or multiple IPs. We select Multiple to explain. Note:
For VCs with single IP, they share the same DMZ and Virtual servers; for VCs with multiple IPs, each VC can set DMZ and Virtual servers. Furthermore, for VCs with multiple IPs, they can define the Address Mapping rules; for VCs with single IP, since they have only one IP, there is no need to individually define the Address Mapping rule. 4.4.3.1 DMZ Choose Advanced SetupNATDMZ in Figure 4-28, you can configure the DMZ host in the next screen. A DMZ (demilitarized zone) is a host between a private local network and the outside public network. It prevents outside users from getting direct access to a server that has company data. Users of the public network outside the company can access to the DMZ host. 43 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide DMZ Host IP Address: Enter the specified IP Address for DMZ host on the LAN side. Figure 4-29 4.4.3.2 Virtual Server Choose Advanced SetupNATVirtual Server in Figure 4-28, you can configure the Virtual Server in the next screen. The Virtual Server is the server or server(s) behind NAT (on the LAN), for example, Web server or FTP server, that you can make visible to the outside world even though NAT makes your whole inside network appear as a single machine to the outside world. Figure 4-30 Rule Index: The Virtual server rule index for this VC. You can specify 10 rules in maximum. All the VCs with single IP will use the same Virtual Server rules. Application: The Virtual servers can be used for setting up public services on your LAN. Protocol: The protocol used for this application. Start & End port number: Enter the specific Start and End Port number you want to forward. If it is one port only, you can enter the End port number the same as Start port number. For example, if you want to set the FTP Virtual server, you can set the start and end port number to 21. Local IP Address: Enter the IP Address for the Virtual Server in LAN side. 44 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Virtual Server Listing: This displays the information about the Virtual Servers you establish. To add a virtual server entry:
Step 1: Select the Virtual Circuit and select Virtual Server. Note:
For VCs with single IP, select Single; For VCs with multiple IPs, select Multiple for the option. Step 2: Select the Rule index for the rule as shown in Figure 4-30. Step 3: Select the application you want from drop-down list, then the protocol and port number will be added to the corresponding field automatically, you only need to configure the IP address for the virtual server; If the application list does not contain the service that you want, please configure the Port number, IP Address and Protocol manually. Step 4: After that, click SAVE to make the entry take effect. Other operations for the entries as shown in Figure 4-30:
Enter the index of assigned entry, and click the DELETE button to delete the entry. Click the BACK button to return to the previous screen. Click the CANCEL button to cancel the configuration which is made just now. 4.4.3.3 IP Address Mapping Select Multiple for numbers of IPs in Figure 4-28, and choose Advanced SetupNATIP Address Mapping(for Multiple IP Service). You can configure the Address Mapping Rule in the next screen. The IP Address Mapping is for those VCs that configured with multiple IPs. The IP Address Mapping rule is per-VC based (only for Multiple IPs' VCs). Rule Index: Select the Virtual server rule index for this VC. You can specify 8 rules in Figure 4-31 maximum. 45 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Rule Typ: There are four types: one-to-one, Many-to-One, Many-to-Many Overload and Many-to-Many No-overload. Local Start & End IP: Enter the local IP Address you plan to map to. Local Start IP is the starting local IP address and Local End IP is the ending local IP address. If the rule is for all local IPs, then the Start IP is 0.0.0.0 and the End IP is 255.255.255.255. Public Start & End IP: Enter the public IP Address you want to do NAT. Public Start IP is the starting public IP address and Public End IP is the ending public IP address. If you have a dynamic IP, enter 0.0.0.0 as the Public Start IP. Address Mapping List: This displays the information about the Mapping addresses. To add a mapping rule:
Step 1: Select the Virtual Circuit and Multiple for the Number of IPs. Then select the tab IP Address Mapping (shown in Figure 4-28). Note:
IP Address Mapping is only available for VCs with Multiple IPs. Step 2: Select the Rule index for the rule as shown in Figure 4-31. Step 3: Select the rule type you want from the drop-down list. Step 4: Enter the local and public IP addresses in the corresponding fields. Step 5: After that, click SAVE to make the entry take effect. Other operations for the entries as shown in Figure 4-31:
Select the index of assigned entry, and click the DELETE button to delete the entry. Click the BACK button to return to the previous screen. Click the CANCEL button to cancel the configuration which is made just now. 4.4.4 QoS Choose Advanced SetupQoS, you can configure the QoS in the next screen. QoS helps to prioritize data as it enters your router. By attaching special identification marks or headers to incoming packets, QoS determines which queue the packets enter, based priority. This is useful when there are certain types of data you want to give higher priority, such as voice data packets give higher priority than Web data packets. This option will provide better service of selected network traffic over various technologies. 46 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide QoS: Select this option to Activate/Deactivate the IP QoS on different types (IP ToS and Figure 4-32 DiffServ). Summary: Click the button to view the configurations of QoS. Rule: Configure the rules for QoS. If the traffic complies with the rule, then the Router will take the corresponding action to deal with it. Rule Index: Select the index for the rule you want to configure. Active: Activate the rule. The rule can take effect only when it is activated. 47 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Application: Select the application that the rule aimed at. Physical Ports: Select the port whose traffic flow are controlled by the rule. Destination MAC & IP & Mask & Port Range: Enter the IP information about the Destination host for the rule. Source MAC & IP & Mask & Port Range: Enter the IP information about the Source host for the rule. Protocol ID: Select one among TCP/UDP, TCP, UDP or ICMP protocols for the application. Vlan ID Range: Enter the Vlan range, and the rule will be effective to the selected Vlans. IPP/DS Field: Select the type of the action to assign the priority. When you select IPP/TOS, you can assign the priority via IP information. IP QoS function is intended to deliver guaranteed as well as differentiated Internet services by giving network resource and usage control to the Network operator. IP Precedence Range: Enter the IP precedence range that the Router takes to differentiate the traffic. Type of Service: Select the type of service that the Router takes to deal with the traffic. 802.1p: Select the priority range for the rule. When you select DSCP, you can assign the priority via DHCP (the header of IP group). It maps the IP group into corresponding service class. DSCP Range: Enter the DSCP range to differentiate the traffic. 802.1p: Select the priority range for the rule. Action: Configure the action that the Router takes to deal with the traffic which accord with the rule. IPP/DS Field: Select the type for the action. IP Precedence Remarking: Select the number to remark the priority for IP precedence. Type of Service Remarking: Select the type to remark the service. DSCP Remarking: Enter the number to remark the DSCP priority. 802.1p Remarking: Select the type to remark the 802.1p priority. Queue: Select the priority type for the action. 48 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.4.5 VLAN Choose Advanced SetupVLAN, you can activate the VLAN function in the next screen. Virtual LAN (VLAN) is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same LAN, when in fact they are located on a number of different LAN segments. Because VLANs are based on logical instead of physical connections, it is very flexible for user/host management, bandwidth allocation and resource optimization. There are two types of VLAN as follows:
Port-Based VLAN: Each physical switch port is configured with an access list specifying membership in a set of VLANs. ATM VLAN: Using LAN Emulation (LANE) protocol to map Ethernet packets into ATM cells and deliver them to their destination by converting an Ethernet MAC address into an ATM address. 1) Assign VLAN PVID for each Interface Figure 4-33 Click Assign VLAN PVID for each Interface in Figure 4-33, you can assign the PVID for each interface in the next screen (shown in Figure 4-34). 49 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-34 PVID: Each physical port has a default VID called PVID (Port VID). PVID is assigned to untagged frames or priority tagged frames (frames with null (0) VID) received on this port. 2) Define VLAN Group Click Define VLAN Group in Figure 4-33, you can define VLAN groups in the next screen (shown in Figure 4-35). 50 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide VLAN Index: Select the VLAN index for this VC. You can specify 8 groups in maximum. Figure 4-35 VLAN ID: This indicates the VLAN group. ATM VCs: Select the ATM VCs as members of VLAN, and if you leave the Tagged blank, the tag in frames will be deleted when transmitted from the VC. Ethernet: Select the Ethernet port as a member of VLAN. Wireless LAN: Select the wireless LAN port as a member of VLAN, and if you leave the Tagged blank, the tag in frames will be deleted when transmitted from the port. VLAN Group Summary: This displays the information about the VLAN Groups. 4.4.6 ADSL Choose Advanced SetupADSL, you can select the ADSL Type and ADSL Mode in the next screen. The ADSL feature can be selected when you meet the physical connection problem. Please check the proper settings with your Internet service provider. 51 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-36 ADSL Mode: Select the ADSL operation mode which your ADSL connection uses. ADSL Type: Select the ADSL operation type which your ADSL connection uses. 4.5 Access Management Choose Access Management, you can see the next submenus:
Click any of them, and you will be able to configure the corresponding function. Figure 4-37 4.5.1 ACL Choose Access ManagementACL, you can see the next screen (shown in Figure 4-38). You can specify the client to access the ADSL Router once setting his IP as a Secure IP Address through selected applications. 52 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-38 ACL: If Activated, the IP addresses which are contained in the Access Control List can access to the Router. If Deactivated, all IP addresses can access to the Router. ACL Rule Index: Select the ACL rule index for the entry. Active: Enable the ACL rule. Secure IP Address: Select the IP addresses which are permitted to access to the Router remotely. With the default IP 0.0.0.0, any client would be allowed to remotely access the ADSL Router. Application: Select the application for the ACL rule, and then you can access the Router through it. Interface: Select the interface for access: LAN, WAN or Both. Access Control of Listing: This displays the information about the ACL Rules. 4.5.2 Filter Choose Access ManagementFilter, you can see the Filter screen (the default is IP/MAC Filter screen shown in Figure 4-39 ). The filtering feature includes IP/MAC Filter, Application Filter, and URL Filter. The feature makes it possible for administrators to control user's access to the Internet, protect the networks. 53 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.5.2.1 IP Filter Select IP/MAC Filter as the Filter type, and select IP as the Rule type (shown in Figure 4-39), then you can configure the filter rules based on IP address. The filtering includes Outgoing and Incoming, the detailed descriptions are provided below. Filter Type Selection: Select the filter type for the configuration below. Figure 4-39 IP/MAC Filter Set Index: Select the Set index for the IP Filter entry. This index can match with six IP / MAC Filter Rule Indexes. Interface: Select the interface for the entry. 54 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Note:
If select PVC0~PVC7 as an interface, the filter will match the IP traffic of WAN port with specified IPs (Source IP Address and Destination IP Address). If select LAN as an interface, the filter will match the IP traffic of LAN port with specified IPs. Direction: Select the direction for this IP Filter rule. There are three filtering directions: Both, Incoming, Outgoing. Note:
Incoming means that IP traffic which is coming into the router, and the Outgoing means that IP traffic which is going out the router. IP/MAC Filter Rule Index: Select the Rule index for the IP Filter entry. Note:
You should set the IP/MAC Filter Set Index and IP/MAC Filter Rule Index together to appoint the address (shown in the Filter List) for the IP Filter rule. For example, (1, 2), it means the rule will be shown in the row 2 IP/MAC Filter Set Index 1. Rule Type: For IP Filter, please select IP here. Active: Select Yes to make the rule to take effect. Source IP Address: Enter the source IP address for the rule. You can enter 0.0.0.0; it means that all IP addresses are controlled by the rule. Destination IP Address: Enter the destination IP address for the rule. You can enter 0.0.0.0, it means that all IP addresses are controlled by the rule. The set of Subnet Mask and Port Number are same as Source IP Address. Subnet Mask: Enter the Subnet Mask for the rule. Port Number: Enter the Port Number for the rule. You can enter 0, which means that all ports are controlled by the rule. Protocol: Select the protocol: TCP, UDP or ICMP for the filter rule. Rule Unmatched: If the current rule can not match, and you select Forward, the router will skip the rule and transmit directly. If you select Next, the router will find the next filter rule
(show in Filter list) to match. IP/MAC Filter Listing: This displays the information about the IP Filter rules. To add an IP Address filtering entry:
For example: If you desire to block E-mail received and sent by the IP address 192.168.1.7 on your local network; And wish to make the PCs with IP address 192.168.1.8 unable to visit the website of IP address 202.96.134.12, while other PCs have no limit. You can configure the rules 55 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide as follows. Presume the rules are both aimed at the interface PVC0, and their indexes are (1, 1),
(1, 2) and (1, 3). Step 1: Select the IP/MAC Filter as the Filter Type Selection (show in Figure 4-39). Select the IP as the Rule Type on the Filter screen, then you can configure the specific rule for the example. Step 2: Select the IP/MAC Filter Set Index and IP/MAC Filter Rule Index for the rule, then select the Interface PVC0, and select the Direction Both for the first rule. Note:
If you want to make the rule take effect, please select Yes to active the rule. Step 3: Enter the Source IP Address, Destination IP Address, Subnet Mask and Port Number in the corresponding field. Step 4: Select the Protocol as TCP and select the Unmatched rule as Next. Step 5: Finally, click the SAVE to save the entry. 56 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Step 6: Go to Step 2 to configure the next two rules: Block E-mail received by the IP address 192.168.1.7 on your local network; Make the PC with IP address 192.168.1.8 unable to visit the website of IP address 202.96.134.12. Note:
After you complete the IP filter rules for the example, the Filter list will show as follows. You can enter the IP / MAC Filter Set Index to view the information about the rule. Other operations for the entries as shown in Figure 4-39:
Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to view or modify the entry. Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to locate the specific rule, and then click the DELETE button to delete the entry. 4.5.2.2 MAC Filter Select IP/MAC Filter as the Filter type, and select MAC as the Rule type (shown in Figure 4-40), and then you can configure the filter rules based on MAC address. 57 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-40 Rule Type: Select MAC for the MAC Filter rule. Active: Select Yes to make the rule to take effect. MAC Address: Enter the MAC address for the rule. Rule Unmatched: If the current rule can not match, and you select Forward, the router will skip the rule and transmit directly. If you select Next, the router will find the next filter rule
(show in Filter list) to match. IP/MAC Filter Listing: This displays the information about the MAC Filter rules. To add a MAC Address filtering entry:
For example: If you want to block the PCs with MAC addresses 00-0A-EB-00-07-BE and 00-0A-EB-00-07-5F to access the Internet, you can configure as follows. Presume the rules are both aimed at the interface PVC0, and their indexes are (1, 1) and (1, 2). Step 1: Select the IP/MAC Filter as the Filter Type Selection:
58 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Select the MAC as the Rule Type on the Filter screen (show in Figure 4-40).
, Then you can configure the specific rule for the example. Step 2: Select the IP/MAC Filter Set Index and IP/MAC Filter Rule Index for the rule, then select the Interface PVC0, and select the Direction Outgoing for the first rule. Note:
If you want to make the rule take effect, please select Yes to active the rule. Step 3: Enter the MAC Address and select the Unmatched rule as Next. Step 4: Finally, click the SAVE to save the entry. Step 5: Go to Step 2 to configure the next rule: Block the PC with MAC address 00-0A-EB-00-07-5F to access the Internet. Note:
After you complete the MAC filter rules for the example, the Filter list will show as follows. You can enter the IP / MAC Filter Set Index to view the information about the rule. Other operations for the entries as shown in Figure 4-39:
Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to view or modify the entry. Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to locate the specific rule, and then click the DELETE button to delete the entry. 59 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.5.2.3 Application Filter Select Application Filter as the Filter type (shown in Figure 4-41), and then you can configure the filter rules based on application. Figure 4-41 Filter Type Selection: Select the Application Filter for the next configuration. Application Filter: Activate or deactivate the function. ICQ & MSN & YMSG & Real Audio/Video: Select Allow or Deny for these applications. If you select Allow, the Router will accept the application; if you select Deny, the Router will forbid the application. 4.5.2.4 URL Select Application Filter as the Filter type (shown in Figure 4-42), and then you can configure the filter rules based on URL. 60 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Filter Type Selection: Select the URL Filter for the next configuration. Figure 4-42 Active: Select Yes to make the rule to take effect. URL Index: Select the index for the URL Filter entry. URL: Enter the URL for this URL Filter. URL Filter Listing: This displays the information about the URL Filter rules. To add a URL filter entry:
For example: If you want to forbid the user to access the website: www.yahoo.com. Presume the rule is aimed at the interface PVC0, and its index is 1. Step 1: Select the URL Filter as the Filter Type Selection (show in Figure 4-42). Step 2: Select the Index for the rule, and then enter the website in the URL field. Step 3: Finally, Select Yes to active the rule, and then click the SAVE to save the entry. 61 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Other operations for the entries as shown in Figure 4-39:
Select the URL Index to view or modify the entry. Select the URL Index to locate the specific rule, and then click the DELETE button to delete the entry. 4.5.3 SNMP Choose Access ManagementSNMP, you can see the SNMP screen. The Simple Network Management Protocol (SNMP) is used for exchanging information between network devices. Figure 4-43 Get Community: Set the password for the incoming Get and Get next requests from the management station. Set Community: Set the password for incoming Set requests from the management station. 4.5.4 UPnP Choose Access ManagementUPnP, you can configure the UPnP in the screen (shown in Figure 4-44). UPnP (Universal Plug and Play) is a distributed, open networking standard that uses TCP/IP for simple peer-to-peer network connectivity between devices. An UPnP device can dynamically join a network, obtain an IP address, convey its capabilities and learn about other devices on the network. In turn, a device can leave a network smoothly and automatically when it is no longer in use. UPnP broadcasts are only allowed on the LAN. 62 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-44 UPnP: Activate or Deactivate the UPnP function. Only when the function is activated, can the UPnP take effect. Auto-Configure: If you activate the function, then the UPnP network devices can automatically configure network addressing, announce their presence in the network to other UPnP devices and enable exchange of simple product and service descriptions. 4.5.5 DDNS Choose Access ManagementDDNS, you can configure the DDNS function in the screen
(shown in Figure 4-45). The router offers a Dynamic Domain Name System (DDNS) feature. The feature lets you use a static host name with a dynamic IP address. User should type the host name, user name and password assigned to your ADSL Router by your Dynamic DNS provider. User also can decide to turn on DYNDNS Wildcard or not. Dynamic DNS: Activate the DDNS function or not. Figure 4-45 63 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Service Provider: This field displays the service provider of DDNS. My Host Name: Enter your host name here. E-mail Address: Enter your E-mail address here. Username & Password: Type the User Name and Password for your DDNS account. Wildcard support: Select the option to use Wildcard function 4.5.6 CWMP Choose Access ManagementCWMP, you can configure the CWMP function in the screen
(shown in Figure 4-46). The router offers CWMP feature. The function supports TR-069 protocol which collects information, diagnoses the devices and configures the devices automatically via ACS (Auto-Configuration Server). Figure 4-46 CWMP: Select activate the CWMP function. URL: Enter the website of ACS which is provided by your ISP. User Name/Password: Enter the User Name and password to login the ACS server. Path: Enter the path that connects to the ACS server. Port: Enter the port that connects to the ACS server. 64 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide User Name/Password: Enter the User Name and Password that provided the ACS server to login the router. Periodic Inform: Activate or deactivate the function. If Activated, the information will be informed to ACS server periodically. Interval: Enter the interval time here. 4.6 Maintenance Choose Maintenance, you can see the next submenus:
Click any of them, and you will be able to configure the corresponding function. Figure 4-47 4.6.1 Administration Choose MaintenanceAdministration, you can set new password for admin in the screen
(shown in Figure 4-48). Figure 4-48 Note:
There is only one account that can access Web-Management interface. The default account is
"admin", and the password is "admin". Admin has read/write access privilege. When you change the password, you should enter the new password twice, and then click SAVE to make the new password take effect. 65 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.6.2 Time Zone Choose MaintenanceTime Zone, you can configure the system time in the screen (shown in Figure 4-49). The system time is the time used by the device for scheduling services. There are three methods to configure the time. You can manually set the time or connect to a NTP (Network Time Protocol) server. If a NTP server is set, you will only need to set the time zone. If you manually set the time, you may also set Daylight Saving dates and the system time will automatically adjust on those dates. 1) NTP Server automatically Select NTP Server automatically as the Synchronize time, you only need to set the time zone. Figure 4-49 Note:
The ADSL Router built-in some NTP Servers, when the Router connects to the Internet, the Router will get the system time automatically from the NTP Server. You can also configure the NTP Server address manually, and then the Router will get the time from the specific Server firstly. 2) PCs Clock Select PCs Clock as the Synchronize time, you dont need to set any items. 66 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-50 3) Manually Select Manually as the Synchronize time, you need to set the date and time corresponding to the current time. Figure 4-51 4.6.3 Firmware Choose MaintenanceFirmware, you can upgrade the firmware of the Router in the screen
(shown in Figure 4-52). Make sure the firmware or romfile you want to use is on the local hard drive of the computer. Click Browse to find the local hard drive and locate the firmware or romfile to be used for upgrade. 67 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-52 To upgrade the router's firmware, follow these instructions below:
Step 1: Type the path and file name of the update file into the New Firmware Location field. Or click the Browse button to locate the update file. Step 2: Click the UPGRADE button. Note:
1. When you upgrade the router's firmware, you may lose its current configurations, so please back up the routers current settings before you upgrade its firmware. 2. Do not turn off the router or press the Reset button while the firmware is being upgraded. 3. The router will reboot after the upgrading has been finished. To back up the Routers current settings:
Step 1: Click the ROMFILE SAVE button (shown in Figure 4-52), click Save button in the next screen (shown in Figure 4-53) to proceed. 68 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-53 Step 2: Save the file as the appointed file (shown in Figure 4-54). TD-W8901N Figure 4-54 To restore the Routers settings:
Step 1: Click the Browse button to locate the update file for the device, or enter the exact path in New Romfile Location field. Step 2: Click the UPGRADE button to complete. 69 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide 4.6.4 SysRestart Choose MaintenanceSysRestart, you can select to restart the device with current settings or restore to factory default settings in the screen (shown in Figure 4-55). Figure 4-55 4.6.5 Diagnostics Choose Maintenance Diagnostics, you can view the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides in the screen (shown in Figure 4-56). 70 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Figure 4-56 4.7 Help Choose Help, you can view the help information for configuration of any function. 71 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Note:
Click the tab, and you will be able to get the corresponding information. Figure 4-57 72 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Appendix A: Specifications Standards and Protocols Safety & Emission Ports LEDs Network Medium Data Rates System Requirement General ANSI T1.413, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.3u, TCP/IP, PPPoA, PPPoE, SNTP, HTTP, DHCP, ICMP, NAT, FCC, CE Four 10/100M Auto-Negotiation RJ45 portsAuto MDI/MDIX) One RJ11 port
(LAN1-4)
(WLAN),
(ADSL),
(Power),
(Internet), 10Base-T: UTP category 3, 4, 5 cable 100Base-TX: UTP category-5 Max line length: 6.5Km Downstream: Up to 24Mbps Upstream: Up to 3.5MbpsWith Annex M enabled) Internet Explorer 5.0 or later, Netscape Navigator 6.0 or later Win 9x/ ME/ 2000/ XP/ Vista/Windows 7/Windows 8 Physical and Environment Working Temperature Working Humidity Storage Temperature Storage Humidity 0 ~ 40 10% ~ 90% RH (non-condensing)
-40 ~ 70 5% ~ 90% RH (non-condensing) 73 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Appendix B: Troubleshooting T1. How do I restore my modem routers configuration to its factory default settings?
With the modem router powered on, press and hold the RESET button on the rear panel for 8 to 10 seconds before releasing it. Note:
Once the modem router is reset, the current configuration settings will be lost and you will need to re-configure the router. T2. What can I do if I dont know or forget my password?
1) Restore the modem routers configuration to its factory default settings. If you dont know how to do that, please refer to T1. 2) Use the default user name and password: admin, admin. 3) Try to configure your modem router once again by following the instructions in 3.2 Login. T3. What can I do if I cannot access the web-based configuration page?
1) Configure your computers IP Address. For Mac OS X Click the Apple icon on the upper left corner of the screen. Go to System Preferences -> Network. Select Airport on the left menu bar, and then click Advanced for wireless configuration;
or select Ethernet for wired configuration. In the Con-figure IPv4 box under TCP/IP, select Using DHCP. Click Apply to save the settings. For Windows 7 Click Start -> Control Panel -> Network and Internet -> View network status ->
Change adapter settings. Right-click Wireless Network Connection (or Local Area Connection), and then click Properties. Select Internet Protocol Version 4 (TCP/IPv4), and then click Properties. Select Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK. 74 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide For Windows XP Click Start -> Control Panel -> Network and Internet Connections -> Network Connections. Right-click Wireless Network Connection (or Local Area Connection), and then click Properties. Select Internet Protocol (TCP/IP), and then click Properties. Select Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK. For Windows 8 Move your mouse to the lower right corner and click the Search icon in the Popups. Go to Apps, type Control Panel in the search box and press Enter. Go to Control Panel -> View network status and tasks > Change adapter settings. Right-click Ethernet, select Properties. Then double-click Internet Protocol Version 4
(TCP/IPv4). Select Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK. 2) Configure your IE browser Open your IE browser, click Tools tab and you will see the following screen. Click Internet Options 75 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Select Never dial a connection Click OK Now, try to log on to the Web-based configuration page again after the above settings have been configured. If you still cannot access the configuration page, please restore your modem routers factory default settings and reconfigure your modem router following the instructions in 3.2 Login. Please feel free to contact our Technical Support if the problem still exists. T4. What can I do if I cannot access the Internet?
1) Check to see if all the connectors are connected well, including the telephone line, Ethernet cables and power adapter. 2) Check to see if you can log on to the web management page of the modem router. If you can, try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet. If the problem persists, please go to the next step. 3) Consult your ISP and make sure all the VPI/VCI, Connection Type, account username and password are correct. If there are any mistakes, please correct the settings and try again. 4) If you still cannot access the Internet, please restore your modem router to its factory default settings and reconfigure your modem router by following the instructions in 3.2 Login. 5) Please feel free to contact our Technical Support if the problem still exists. Note:
For more details about Troubleshooting and Technical Support contact information, please log on to our Technical Support Website: http://www.tp-link.com/en/support 76 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Appendix C: Technical Support Technical Support For more troubleshooting help, go to: http://www.tp-link.com/en/support/faq To download the latest Firmware, Driver, Utility and User Guide, go to:
http://www.tp-link.com/en/support/download For all other technical support, please contact us by using the following details:
Global Tel: +86 755 2650 4400 Fee: Depending on rate of different carriers, IDD. E-mail: support@tp-link.com Service time: 24hrs, 7 days a week USA/Canada Toll Free: +1 866 225 8139 E-mail: support.usa@tp-link.com (USA) support.ca@tp-link.com (Canada) Service time: 24hrs, 7 days a week Turkey Tel: 0850 7244 488 (Turkish Service) Fee: Depending on rate of different carriers. E-mail: support.tr@tp-link.com Service time: 09:00 to 21:00, 7 days a week Ukraine Tel: 0800 505 508 Fee: Free for Landline; Mobile: Depending on rate of different carriers E-mail: support.ua@tp-link.com Service time: Monday to Friday, 10:00 to 22:00 Brazil Toll Free: 0800 608 9799 (Portuguese Service) E-mail: suporte.br@tp-link.com Service time: Monday to Friday, 09:00 to 20:00;
Saturday, 09:00 to 15:00 Indonesia Tel: (+62) 021 6386 1936 Fee: Depending on rate of different carriers. E-mail: support.id@tp-link.com Service time: Sunday to Friday, 09:00 to 12:00 13:00 to 18:00 *Except public holidays Australia/New Zealand Tel: NZ 0800 87 5465 (Toll Free) AU 1300 87 5465 (Depending on 1300 policy.) E-mail: support.au@tp-link.com (Australia) support.nz@tp-link.com (New Zealand) Service time: 24hrs, 7 days a week Germany/Austria Tel: +49 1805 875 465 (German Service)
+49 1805 TPLINK
+43 820 820 360 Fee: Landline from Germany: 0.14EUR/min. Landline from Austria: 0.20EUR/min. E-mail: support.de@tp-link.com Service time: Monday to Friday, 09:00 to 12:30 and 13:30 to 18:00. GMT+1 or GMT+2 (DST in Germany) *Except bank holidays in Hesse Singapore Tel: +65 6284 0493 Fee: Depending on rate of different carriers. E-mail: support.sg@tp-link.com Service time: 24hrs, 7 days a week UK Tel: +44 (0) 845 147 0017 Fee: Landline: 1p-10.5p/min, depending on the time of day. Mobile: 15p-40p/min, depending on your mobile network. E-mail: support.uk@tp-link.com Service time: 24hrs, 7 days a week Italy Tel: +39 023 051 9020 Fee: Depending on rate of different carriers. E-mail: support.it@tp-link.com Service time: Monday to Friday, 09:00 to 13:00;
14:00 to 18:00 Malaysia Toll Free: 1300 88 875 465 Email: support.my@tp-link.com Service time: 24hrs, 7 days a week Poland Tel: +48 (0) 801 080 618
+48 223 606 363 (if calls from mobile phone) Fee: Depending on rate of different carriers. E-mail: support.pl@tp-link.com Service time: Monday to Friday, 09:00 to 17:00. GMT+1 or GMT+2 (DST) France Tel: 0820 800 860 (French service) Fee: 0.118 EUR/min from France Email: support.fr@tp-link.com Service time: Monday to Friday, 09:00 to 18:00
*Except French Bank holidays Switzerland Tel: +41 (0) 848 800 998 (German Service) Fee: 4-8 Rp/min, depending on rate of different time. E-mail: support.ch@tp-link.com Service time: Monday to Friday, 09:00 to 12:30 and 13:30 to 18:00. GMT+1 or GMT+2 (DST) Russian Federation Tel: 8 (499) 754 5560 (Moscow NO.) 8 (800) 250 5560 (Toll-free within RF) E-mail: support.ru@tp-link.com Service time: From 10:00 to 18:00 (Moscow time)
*Except weekends and holidays in RF 77
| frequency | equipment class | purpose | ||
|---|---|---|---|---|
| 1 | 2014-04-09 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
| app s | Applicant Information | |||||
|---|---|---|---|---|---|---|
| 1 | Effective |
2014-04-09
|
||||
| 1 | Applicant's complete, legal business name |
TP-Link Technologies Co., Ltd.
|
||||
| 1 | FCC Registration Number (FRN) |
0013661145
|
||||
| 1 | Physical Address |
Building 24 (floors 1,3,4,5) and 28 (floors1-4)
|
||||
| 1 |
Shenzhen, N/A 518057
|
|||||
| 1 |
China
|
|||||
| app s | TCB Information | |||||
| 1 | TCB Application Email Address |
h******@acbcert.com
|
||||
| 1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
| app s | FCC ID | |||||
| 1 | Grantee Code |
TE7
|
||||
| 1 | Equipment Product Code |
TDW8901NV2
|
||||
| app s | Person at the applicant's address to receive grant or for contact | |||||
| 1 | Name |
J****** H****
|
||||
| 1 | Title |
Regulatory Compliance Manager
|
||||
| 1 | Telephone Number |
75521********
|
||||
| 1 | Fax Number |
75526********
|
||||
| 1 |
c******@tp-link.com
|
|||||
| app s | Technical Contact | |||||
| 1 | Firm Name |
AUDIX Technology (Shenzhen) Co., Ltd.
|
||||
| 1 | Name |
L**** S****
|
||||
| 1 | Physical Address |
52 Block Shenzhen Science&Industry
|
||||
| 1 |
Shenzhen
|
|||||
| 1 |
China
|
|||||
| 1 | Telephone Number |
86-75********
|
||||
| 1 |
s******@audix.com.cn
|
|||||
| app s | Non Technical Contact | |||||
| n/a | ||||||
| app s | Confidentiality (long or short term) | |||||
| 1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
| if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
| app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
| 1 | Is this application for software defined/cognitive radio authorization? | No | ||||
| 1 | Equipment Class | DTS - Digital Transmission System | ||||
| 1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | 150Mbps Wireless N ADSL2+ Modem Router | ||||
| 1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
| 1 | Modular Equipment Type | Does not apply | ||||
| 1 | Purpose / Application is for | Original Equipment | ||||
| 1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
| 1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
| 1 | Grant Comments | Power Output listed is conducted. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and not be co-located with any other transmitters except in accordance with FCC multi transmitter product procedures. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This devcie has a 20 MHz and 40 MHz bandwidth mode. | ||||
| 1 | Is there an equipment authorization waiver associated with this application? | No | ||||
| 1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
| app s | Test Firm Name and Contact Information | |||||
| 1 | Firm Name |
Audix Technology (Shenzhen) Co., Ltd.
|
||||
| 1 | Name |
S****** T******
|
||||
| 1 | Telephone Number |
86-75******** Extension:
|
||||
| 1 | Fax Number |
86-75********
|
||||
| 1 |
s******@audix.com.cn
|
|||||
| Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
| 1 | 1 | 15C | 68 | 2412.00000000 | 2462.00000000 | 0.3733000 | |||||||||||||||||||||||||||||||||||
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC