Installation Guide Outdoor CPE Get Started with Setup Videos Scan the QR code or visit https://www.tp-link.com/support/setup-video/
Contents Overview Hardware Connection Site Consideration Connection and Installation Lightning & ESD Protection
Logging in to the PharOS
FAQ 01 04 04 06 08
10
16
Overview TP-Link's Pharos series outdoor CPEs are dedicated to outdoor wireless
Power Cord Pole Mounting Straps Installation Guide Outdoor CPE Need setup videos?
Scan the QR code or visit https://www.tp-link.com/en/support/setup-video/
Installation Guide Pharos CPE Mounting Bracket
Passive PoE Adapter LED Explanation
AP/AP Router Mode:
All four LEDs remain solid.
On: The CPE is powered on. L A N 1 L A N 0 P O W E R 01 Panel Layout
Grounding Terminal Shielded Ethernet Port LAN0 (Passive PoE IN) Shielded Ethernet Port LAN1 RESET
Grounding Terminal Shielded Ethernet Port LAN (Passive PoE IN) RESET
Passive PoE Adapter:
Press and hold for about 8 seconds until CPEs LEDs of wireless signal
Power LED The Power LED is on when the passive PoE adapter is working normally. 03 Application Example The CPE device(CPE210 CPE220 CPE510) provides outdoor network access over long distances for point-to-point applications. 4 Hardware Connection 1. Site Consideration
Ensure a clear line of sight between the wireless devices for an optimum performance. An elevated location is recommended as obstacles like
height of the devices. Line of Sight Side View 04 Orientation Install the CPE devices with the front facing the intended signal receiving
GPS and some landmarks according to the horizontal beamwidth listed below. Models Horizontal Beamwidth
A Line of Sight shenzhen Horizontal Beamwidth B
2. Connection and Installation Connect and mount the CPE and power adapter as shown below. The
LAN0 PoE LAN Ethernet cable length up to 60m You should prepare an adequate Ethernet cable to connect the CPE and the passive PoE adapter. Shielded CAT5e (or above) cable with ground wire is recommended
(refer to the next section). Connect to a computer, router or switch.
(Depending on your intended usage and/or network topology.) Slide to replace the cover of the CPE when all
06
have oriented.
Follow the steps below to mount the power adapter:
recommended to install the adapter with the Ethernet port facing upward. 1. Drill two holes on the wall and insert the plastic wall anchors into the holes. Secure the mounting bracket to the wall. Make sure the shoulders at the corners of the mounting bracket are on the outside and pointing upward.
Attach the passive PoE adapter to the mounting bracket by sliding the adapter in the direction of the arrows until it locks into place. 07 3. Lightning & ESD Protection
connection and the provided PoE adapter (method 1
CPE to earth ground through grounding cable (method
Two Methods:
1 Shielded CAT5e (or above) Cable with Ground Wire Grounding Terminal and Cable 2 Grounding Terminal Grounded 3-wire Power Outlet CPE Grounding Cable 1 PoE Adapter with Earth Ground Shielded CAT5e (or above) Cable with Ground Wire 1 1 2 Earth Ground 08 Sheath Twisted Pair Ground Wire Cable Shield Secondary Cable Shield Shielded RJ45 Connector
09
This chapter introduces the login to the PharOS Web Interface and the
1. Logging in to the PharOS 1.
and press Enterreturn
10 3. Enter for both and Password. Read and agree the
. 4. Change the default User Name and Password to protect your CPE.
download the User Guide of Pharos products in the download center. 11 2. The typical topology is as follows. A wireless bridge is built between two locations that are far from each other. Follow the instructions below to
Computer IP Camera Access Point LAN: 192.168.0.254 Client LAN: 192.168.0.2 Log in to PharOS and go to the Quick Setup page.
1.
Operation Mode: Select Access Point and click Next. 3. 4. Wireless AP Settings:
LAN Settings: Click Next.
b. Select WPA-PSK/WPA2-PSK for the Security method and create a PSK Password to protect your AP. c. Enter the distance between the Access Point and the Client into
d. Select the
Next.
Finish: Verify your settings and click Finish to complete the
1.
Operation Mode: Select Client and click Next. Log in to PharOS and go to the Quick Setup page.
3.
click Next. 4. Wireless Client Settings:
then click Connect. a. Click Survey b. Select WPA-PSK/WPA2-PSK
click Next.
Finish: Verify your settings and click Finish to complete the
download the User Guide of Pharos products in the download center. 13 Antenna Alignment Antenna alignment can help you to optimize the antenna signal. To get the
list on the upper-right corner and enable Alignment Beep during align-
ment. Then adjust your antenna until the sound frequency turns to the lowest.
can help you to estimate the signal strength received by
the signal strength. WISP WISP 14
HARDWARE FEATURES Models
LAN: 10/100 Mbps
LAN0: 10/100 Mbps
LAN1: 10/100 Mbps Ethernet Port GND: Grounding Terminal for Lightning Protection RESET: Button to restore the device to Factory Default Passive PoE Adapter Included
-40 to 70 (-40 10% to 90%
11b/g/n
13 dBi
11a/n Interface Power Supply ESD Protection1
1 Up to 6 kV
WIRELESS FEATURES Models Antenna Gain Horizontal
2 802.11 Standards
9 dBi 11b/g/n
Note:
with ground wire.
FAQ Q1. How to restore the CPE to its factory default
RESET button on the CPE or the Remote Reset button on the Passive PoE Adapter. Method 1: Via the RESET Button on the CPE
RESET Button Press and hold for about 8 seconds until CPEs LEDs of wireless signal
Adapter
Press and hold for about 8 seconds until CPEs
16
which is caused by obstacles in the path between the transmitter and the receiver. Fresnel Zone is a usual method to calculate this
d2 d1 r H h+r*(1 40%)
(H is the height of the CPE) h = the height of obstacle at this point
r = Fresnel zone radius in meters
8 f = operating frequency of the devices in Hz d1 & d = the distances between the point and the devices in meters
d1d2f r
h
https://en.wikipedia.org/wiki/Fresnel_zone 17 Q3. What is Pharos MAXtream?
more stability.
collision.
compatible with TP-Links Pharos series products. Please notice that you will not be able to connect other Wi-Fi devices to an AP with
appropriate channel for the devices?
1. in the tools drop-down
will be lost during spectrum analysis. Click Yes to continue to the Spectrum Analysis page.
Click Start
Stop. Note that the relatively low and continuous part of the average curve 18
Community. 19 Safety Information
Do not use damaged charger or USB cable to charge the device. Do not use any other chargers than those recommended Do not use the device where wireless devices are not allowed. Adapter shall be installed near the equipment and shall be easily accessible. Use only power supplies which are provided by manufacturer and in the original
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.
FCC compliance information statement TL-POE2412G Product Name: Outdoor CPE Model Number: CPE220/CPE510 Component Name Model I.T.E. Power Supply Responsible party:
TP-Link USA Corporation, d/b/a TP-Link North America,Inc. Address: 145 South State College Blvd. Suite 400, Brea, CA 92821 Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234 Fax: +1 909 527 6803 E-mail: sales.usa@tp-link.com This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by
authority to operate the equipment. Product Name: Outdoor CPE Model Number: CPE 210 Component Name Model I.T.E. Power Supply Responsible party:
TP-Link USA Corporation, d/b/a TP-Link North America,Inc. Address: 145 South State College Blvd. Suite 400, Brea, CA 92821 Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234 Fax: +1 909 527 6803 cause undesired operation. TL-POE2412G E-mail: sales.usa@tp-link.com This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by
authority to operate the equipment. FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure compliance requirements, this grant is applicable to
provide a separation distance of at least 25 cm from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter. cause undesired operation. FCC compliance information statement Product Name: I.T.E. Power Supply Model Number: TL-POE2412G Responsible party:
TP-Link USA Corporation, d/b/a TP-Link North America, Inc. Address: 145 South State College Blvd. Suite 400, Brea, CA 92821 Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234 Fax: +1 909 527 6803 E-mail: sales.usa@tp-link.com This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated. Issue Date: 2019.07.25 cause undesired operation. CE Mark Warning For CPE220/CPE510:
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. For CPE210:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. OPERATING FREQUENCY(the maximum transmitted power) 2412MHz2472MHz(20dBm) (CPE210/CPE220) 5500MHz5700MHz(30dBm) (CPE510) EU declaration of conformity TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and
(EU)2015/863. The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce RF Exposure Information This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of
body. Canadian Compliance Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
1) This device may not cause interference. 2) This device must accept any interference, including interference that may cause Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
undesired operation of the device. 1) Lappareil ne doit pas produire de brouillage;
2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Caution: (For CPE510) The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
Avertissement: (For CPE510) Le dispositif fonctionnant dans la bande 5150-5250 MHz est rserv uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Industry Canada Statement (For CPE220/CPE510) CAN ICES-3 (A)/NMB-3(A) Industry Canada Statement (For CPE210) CAN ICES-3 (B)/NMB-3(B) Korea Warning Statements
(For CPE220/CPE510)
NCC Notice & BSMI Notice
For CPE510
(For CPE220/CPE510)
Explanation of the symbols on the product label Symbol Explanation DC voltage RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pur-
suant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a compe-
tent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
access to the respective GPL Code used in TP-Link products are available to you in GPL-Code-Centre under
GPL. 2019 TP-Link