5GHz 300Mbps 13dBi Outdoor CPE User Manual revised

 

Installation Guide Outdoor CPE CPE210 / CPE220 / CPE510 / CPE520 Contents Overview Hardware Connection Site Consideration Connection and Installation Lightning & ESD Protection Software Configuration Logging in to the PharOS Typical Application Configuration Antenna Alignment Specifications FAQ 01 04 04 06 08 10 10 12 14 15 16 Overview TP-Link's Pharos series outdoor CPEs are dedicated to outdoor wireless network solutions. This guide is applicable to products including CPE210, CPE220, CPE510 and CPE520. Package Contents Power Cord Pole Mounting Straps Installation Guide Outdoor CPE CPE210 / CPE220 / CPE510 / CPE520 Installation Guide Pharos CPE Passive PoE Adapter Mounting Bracket Plastic Wall Anchors (Qty.2) Self-tapping Screws (Qty.2) LED Explanation The following picture takes CPE520 as an example. AP/AP Router mode:

All four LEDs remain solid. Client/Bridge/Repeater/AP Client Router mode:(Except CPE510) That the more LEDs lit will indicate better wireless signal strength. On: A device is connected to this port, but there is no activity. Flashing: A device is connected to this port, and is active. On: The CPE is powered on. L A N 1 L A N 0 P O W E R 01 Panel Layout Pharos CPE220/CPE520:

Grounding Terminal Shielded Ethernet Port LAN0 (Passive PoE in) Shielded Ethernet Port LAN1 RESET Pharos CPE210/CPE510:

Grounding Terminal Shielded Ethernet Port LAN (Passive PoE in) RESET 02 Passive PoE Adapter:

Remote Reset Press and hold for 8 seconds to reset the CPE to its factory defaults. Power LED The Power LED is on when the passive PoE adapter is working normally. 03 Hardware Connection 1. Site Consideration Mounting Height Ensure a clear line of sight between the wireless devices for an optimum performance. An elevated location is recommended as obstacles like trees, buildings and large steel structures will weaken the wireless signal. See 'Q2' in 'FAQ' for details about how to calculate the minimum mounting height of the devices. Line of Sight Side View 04 Orientation Install the CPE devices with the front facing the intended signal receiving devices. You can orient the devices with the assistance of Google Maps, GPS and some landmarks according to the horizontal beamwidth listed below. Models Horizontal Beamwidth 65 CPE220 60 CPE510 45 CPE520 45 CPE210 A Line of Sight shenzhen Horizontal Beam width B 05 2. Connection and Installation Connect and mount the CPE and power adapter as shown below. The following introduction takes CPE520 as an example. Connecting CPE and Power Adapter Connect the CPE and power adapter as shown in the figure below. LAN0 PoE LAN Ethernet cable length up to 60m You should prepare an adequate Ethernet cable to connect the CPE and the passive PoE adapter. Shielded CAT5e (or above) cable with ground wire is recommended

(refer to the next section). Connect to a computer, router or switch.

(Depending on your intended usage and/or network topology.) Slide to replace the cover of the CPE when all connections are finished. 06 Mounting CPE At the selected site, approximately align the CPE to the direction that you have oriented. Mounting Power Adapter (Optional) Follow the steps below to mount the power adapter:

To ensure the passive PoE adapter is attached most securely, it is recommended to install the adapter with the Ethernet port facing upward. 1. Drill two holes on the wall and insert the plastic wall anchors into the the holes. Secure the mounting bracket to the wall. Make sure the shoulders at the corners of the mounting bracket are on the outside and pointing upward. 2. Attach the passive PoE adapter to the mounting bracket by sliding the adapter in the direction of the arrows until it locks into place. 07 3. Lightning & ESD Protection Proper grounding is extremely important for outdoor devices. By using shielded CAT5e (or above) cable with ground wire for the connection and the provided PoE adapter (method 1 ), you can effectively eliminate ESD attacks. If you use the general CAT5e cable for the connection, then it is necessary to connect the grounding terminal of the CPE to earth ground through grounding cable (method 2 ). The following introduction takes CPE520 as an example. Two Methods:

1 Shielded CAT5e (or above) Cable with Ground Wire Grounding Terminal and Cable 2 Grounded 3-wire Power Outlet 1 PoE Adapter with Earth Ground CPE Grounding Cable Grounding Terminal Shielded CAT5e (or above) Cable with Ground Wire 1 1 2 Earth Ground 08 Sheath Twisted Pair Ground Wire Cable Shield Secondary Cable Shield Shielded RJ45 Connector Shielded CAT5e (or above) Cable with Ground Wire 09 Software Configuration This chapter introduces the login to the PharOS Web Interface and the software configurations. 1. Logging in to the PharOS 1. Before accessing the PharOS Web Interface, you need to assign a static IP address 192.168.0.X (X ranges between 2 and 253, e.g. 192.168.0.10) to your computer. 2. Open a web browser, type http://192.168.0.254 into the address field and press Enter (Windows) or return (Mac). It is recommended to use the latest version of Google Chrome, Firefox or Safari. 10 3. Enter admin for both User Name and Password. Read and agree the terms of use, then click Login. 4. Change the default User Name and Password to protect your CPE. Lets start configuring the CPE. For subsequent logins, use the new username and password. For more configurations, please visit http://www.tp-link.com/support to download the User Guide of PharOS products in the download center. 11 2. Typical Application Configuration The typical topology is as follows. A wireless bridge is built between two locations that are far from each other. Follow the instructions below to configure the Access Point and the Client. Computer IP camera Access Point LAN: 192.168.0.254 Client LAN: 192.168.0.2 Log in to PharOS and go to the Quick Setup page. Configure the Access Point (AP) 1. 2. Operation Mode: Select Access Point and click Next. 3. 4. Wireless AP Settings:

LAN Settings: Click Next. a. Create a new SSID (Network name) for your wireless network. b. Select WPA-PSK/WPA2-PSK for the Security method and create a PSK Password to protect your AP. c. Enter the distance between the Access Point and the Client into the Distance Setting field. d. Select the MAXtream checkbox (Refer to Q3 in FAQ for details about MAXtream), and click Next. 5. Finish: Verify your settings and click Finish to complete the configuration.

(except CPE510) Configure the Client 1. 2. Operation Mode: Select Client and click Next. Log in to PharOS and go to the Quick Setup page. 12 3. LAN Settings: Change the IP Address to 192.168.0.X (X ranges between 2 and 253), the same subnet with the access point, and click Next. 4. Wireless Client Settings:

then click Connect. a. Click Survey and select the SSID of the Access Point in the AP list, b. Select WPA-PSK/WPA2-PSK from the Security option, enter the same PSK password and distance value of the Access Point, then click Next. 5. Finish: Verify your settings and click Finish to complete the configuration. For more configurations, please visit http://www.tp-link.com/support to download the User Guide of PharOS products in the download center. 13 Antenna Alignment In order to get the best performance, you can precisely align the direction of the CPE with the assistance of Wireless Signal Quality on STATUS page of the PharOS Web Interface. Adjust the direction of the CPE until the device reaches the highest SNR. WISP WISP 14 Carrier Sense Specifications HARDWARE FEATURES Dimensions CPE510/CPE210 LAN: 10/100Mbps Ethernet Port(PoE IN) CPE520/CPE220: 275.83*79*60.3mm CPE510/CPE210: 224.34*79*60.3mm CPE520/CPE220 LAN0: 10/100Mbps Ethernet Port(PoE IN) LAN1: 10/100Mbps Ethernet Port GND: Grounding Terminal for Lightning Protection RESET: Button to restore the device to Factory Default 24V Passive PoE Adapter Included 15kV Interface Power Supply ESD Protection1 Lightning Protection1 Up to 6kV Operating Temperature Operating Humidity Certification WIRELESS FEATURES Models Antenna Gain Horizontal Beamwidth/Elevation Beamwidth2 802.11 Standards CPE210 10.7dBi 11b/g/n 65/ 35 10% to 90 %

CE, FCC, RoHS, IPX5 CPE220 12dBi 60/ 30 11b/g/n CPE510 13dBi CPE520 16dBi 45/ 30 45/ 30 11a/n 11a/n Note:

1. Estimation is based on copper grounding cable and shielded CAT5e cable with ground wire. 2. Beamwidth values may vary throughout operating frequency. 14 FAQ Q1. How to restore the CPE to its factory default settings?

With the CPE powered on, press and hold the RESET button on the CPE or the Remote Reset button on the passive PoE adapter for about 8 seconds until the Wireless Signal Strength LEDs flash. Method 1:

The following picture takes CPE520 as an example. RESET Button Press & hold for about 8 seconds Method 2:

Remote Reset Button Press & hold for about 8 seconds 16 Q2. How to calculate the minimum mounting height of the devices?

In order to maximize the received signal strength of the devices, installers need to minimize the effect of the out-of-phase signals, which is caused by obstacles in the path between the transmitter and the receiver. Fresnel Zone is a usual method to calculate this path, as shown in the formula and the figure below. d2 d1 r h = the height of obstacle at this point H h+r*(1 40%)

(H is the height of the CPE) r

=

d d 1 1

+

d d 2 2 c f where, r = Fresnel zone radius in meters c = 3x108 m/s, speed of light f = operating frequency of the devices in Hz d1 & d2 = the distances between the point and the devices in meters For example, assume d1 is 2km, d2 is 8km, and f is 2.4GHz, then r would be 14.142m. Considering a toleration of 40%, allowable radius would be 8.485m. Assume h is 10m, then the result of the minimum mounting height based on this point would be 18.485m. Similarly, calculate the results based on all the points where there are obstacles, and the maximum value would be the final result. For more information, please refer to:

http://en.wikipedia.org/wiki/Fresnel_zone 17 Q3. What is Pharos MAXtream?

Pharos MAXtream is a proprietary protocol developed on the basis of Time Division Multiple Access (TDMA) by TP-Link. The MAXtream technology has the following advantages:

Eliminates hidden node collisions & improves channel efficiency. Lower latency, higher throughput, larger network capacity &

more stability. Improves the QoS for video, voice and sound data stream. By dividing the timing of transmission into different time slots, MAXtream allows the Pharos devices to transmit in rapid succession, one after another, each using its own time slot to transmit and receive their own frames, which greatly reduces the chance of collision. Pharos MAXtream is a non-standard Wi-Fi protocol that is only compatible with TP-Links Pharos series products. Please notice that you will not be able to connect other Wi-Fi devices to an AP with MAXtream enabled. Q4. How can I use Spectrum Analysis to find the appropriate channel for the devices?

1. Log in to PharOS, click Spectrum Analysis in the tools drop-down list, a window will pop up to remind you that all wireless connections will be lost during spectrum analysis. Click Yes to continue to the Spectrum Analysis page. 2. Click Start, the PharOS will begin to analyze the power of frequency. Observe the curves for a period of time, and then click Stop. Note that the relatively low and continuous part of the 18 average curve indicates less radio noise. Here, we use the figure below as an example. The select box of Frequency Range at the top-left corner is only available for CPE510 and CPE520. Select the desired range and then click Start. When choosing channel/frequency, you should avoid the spectrum with large radio noise. In this example, the recommended channel/

frequency is 112/5560MHz. 19 FCC STATEMENT (For CPE220/CPE510/CPE520) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. cause undesired operation.

(For CPE510) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. cause undesired operation. FCC RF Radiation Exposure Statement:

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 32 cm from all persons and must not be co-

located or operating in conjunction with any other antenna or transmitter. CE Mark Warning For CPE220/CPE510/CPE520:

This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. For CPE210:

This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. OPERATING FREQUENCY(the maximum transmitted power) 2412MHz2472MHz(20dBm) (CPE210/CPE220) 5500MHz5700MHz(27dBm) (CPE510/CPE520) EU declaration of conformity TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC and 2011/65/EU. The original EU declaration of conformity may be found at http://www.tp-link.com/en/ce RF Exposure Information This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. The device complies with RF specifications when the device used at 20 cm from your body. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSSs. Operation is subject to the following two conditions:

1) This device may not cause interference, and 2) This device must accept any interference, including interference that may cause Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1) 2) lappareil ne doit pas produire de brouillage;

lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, meme si le brouillage est susceptible den compromettre le fonctionnement. undesired operation of the device. Caution: (For CPE510/CPE520) 1)The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

2)For devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and The high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement: (For CPE510/CPE520) 1)Le dispositif fonctionnant dans la bande 5150-5250 MHz est rserv uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

2)Le gain maximal d'antenne permis pour les dispositifs avec antenne(s) amovible(s) utilisant la bande 5725-5850 MHz doit se conformer la limitation P.I.R.E spcifie pour lexploitation point point et non point point, selon le cas. En outre, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Industry Canada Statement (For CPE220/CPE510/CPE520) CAN ICES-3 (A)/NMB-3(A) Industry Canada Statement (For CPE210) CAN ICES-3 (B)/NMB-3(B) Safety Information Keep the device away from water, fire, humidity or hot environments. Do not attempt to disassemble, repair, or modify the device. Do not use damaged charger or USB cable to charge the device. Do not use any other chargers than those recommended Do not use the device where wireless devices are not allowed. Adapter shall be installed near the equipment and shall be easily accessible. Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don't hesitate to contact us. Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk. NCC Notice & BSMI Notice

(For CPE220/CPE510/CPE520)

,

. Explanation of the symbols on the product label Symbol Explanation DC voltage RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.

(For CPE220/CPE510/CPE520) A VCCI-A