GLM300 Wireless N module User Manual

User Manual Product User Manual Wireless N module Model Number: GLM-300 ALPHA Proprietary and Confidential Information Introduction This module is the wireless networking device based on 802.11b/g technology and compatible for interoperability with 802.11n devices. This device provides up to 150Mbps transfer rate in the wireless network and let users access the Internet resource, sharing file, and email quickly and your wireless communications are protected by up to WPA2 encryption, so your data stays secure. The extremely small design makes it easy to install into new or existing wireless device and lets you to connect wirelessly to your network. It gives you the ability to roam at home or in the office without wires. Features z Compatible with IEEE 802.11b/g and 802.11n Standard for 2.4GHz Wireless z SoC solution combines 802.11n draft compliant 1T1R MAC/BBP/RF z Up to 150Mbps High-Speed PHY transfer rate on the wireless LAN interface z Works with All Existing Network Infrastructure. z Compatible with Wi-Fi Wireless Products and Services. z Capable of 64/128-Bit WEP, 256bit WPA and WPA2 Encryption z One I-PEX Connectors for External Antenna z Rich hardware interfaces (SPI/I2S/I2C/UART) to enable many possible applications. z Support IEEE 802.3 full duplex flow control z Support USB host mode System Hardware z Processor : Ralink RT-3050 Single Chip SoC 320MHz CPU CLK z MIPS 24KEc 320MHz with 32KB I cache/16KB D cache z Embedded 1Tx1R 2.4G CMOS RF z Chipset maximum consumption 1.45W z 802.11n 1T1R MAC/BBP z 1 port 10/100Mbps PHY z 16 bit 106MHz SDRAM z Support 16 bit NOR FLASH (up-to 8 Mbytes) z SDRAM: 32M Byte (16Mx16) z Flash ROM: 4M Byte (2Mx16) z 3.3V DC switching type power adapter z Interface : 1x 10/100 Base-T LAN port z Other interface : UART, JTAG, GPIOs, WPS button, reset button z Power Requirement:

Operating Voltage: 3.3V DC Output power:

System Software STANDARDS z IEEE 802.11b/g z IEEE 802.11n draft 2.0 z IEEE 802.3 z IEEE 802.3u z System use Linux 2.6. WIRELESS SECURITY z WEP (64/128 bit) z WPA / WPA2 z QOS- WMM, WMM Power Save 4 Physical dimensions & Environmental Dimensions: 46mm(L) x 40mm(W) x 5.6mm(H) Operation Temperature: 0~40 ( 32 to 104)

* Recommend operating under the condition of good airflow Storage Temperature: -25~55 (-13 to 131) Humidity: 5%~95% non-condensing.

* Environmental factors may affect actual range Safety and Emission (Base on region and customers request) EMI: FCC class B, CE lass B EMI: FCC 15C/ FCC MPE/ NCC LP0002 Safety: UL, TUV PIN Description TBD PCB Dimension PCBA dimension : TBD mm(W) x mm(H) PCB dimenstion: 46mm(L)

------END------

5 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID:

XU8GLM300. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Note: 1. 2.

:

XXXyyyLPDzzzz-x (NCC ID)