submitted | available | document details (if available) | source link |
---|---|---|---|
UG_TEW-651BR_1.02_ EmilyYang AFPL Ghostscript 8.54 |
various | UserMan-1 | Users Manual | 1.90 MiB |
i Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
-
-
-
-
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. For Taiwan Europe EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:
EN60950-1: 2006 Safety of Information Technology Equipment EN 50385: 2002 Product standard to demonstrate the compliance of radio base stations and fixed terminal stations for wireless telecommunication systems with the basic restrictions or the reference levels related to human exposure to radio frequency electromagnetic fields
(110MHz - 40 GHz) - General public EN 300 328 V1.7.1 (2006-10) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive ii EN 301 489-1 V1.8.1 (2008-04) Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements EN 301 489-17 V1.3.2 (2008-04) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. 0560 esky [Czech]
TRENDnet tmto prohlauje, e tento TEW-651BR je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES. Dansk [Danish]
Undertegnede TRENDnet erklrer herved, at flgende udstyr TEW-651BR overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklrt TRENDnet, dass sich das Gert TEW-651BR in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian]
Kesolevaga kinnitab TRENDnet seadme TEW-651BR vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. English Hereby, TRENDnet, declares that this TEW-651BR is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Espaol [Spanish]
Por medio de la presente TRENDnet declara que el TEW-651BR cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
[Greek] TRENDnet TEW-651BR 1999/5/. Franais [French]
Par la prsente TRENDnet dclare que l'appareil TEW-651BR est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian]
Con la presente TRENDnet dichiara che questo TEW-651BR conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian]
Ar o TRENDnet deklar, ka TEW-651BR atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem.
[Lithuanian]
Lietuvi iuo TRENDnet deklaruoja, kad is TEW-651BR atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands Hierbij verklaart TRENDnet dat het toestel TEW-651BR in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
[Dutch]
Malti [Maltese]
Hawnhekk, TRENDnet, jiddikjara li dan TEW-651BR jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
[Hungarian]
Magyar Alulrott, TRENDnet nyilatkozom, hogy a TEW-651BR megfelel a vonatkoz alapvet kvetelmnyeknek s az 1999/5/EC irnyelv egyb elrsainak. Polski [Polish]
Niniejszym TRENDnet owiadcza, e TEW-651BR jest zgodny z zasadniczymi wymogami oraz pozostaymi iii stosownymi postanowieniami Dyrektywy 1999/5/EC. Portugus
[Portuguese]
TRENDnet declara que este TEW-651BR est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE.
[Slovenian]
Slovensko TRENDnet izjavlja, da je ta TEW-651BR v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive 1999/5/ES. Slovensky [Slovak]
TRENDnet tmto vyhlasuje, e TEW-651BR spa zkladn poiadavky a vetky prslun ustanovenia Smernice 1999/5/ES. Suomi [Finnish]
TRENDnet vakuuttaa tten ett TEW-651BR tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Svenska [Swedish] Hrmed intygar TRENDnet att denna TEW-651BR str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. iv TABLE OF CONTENT ABOUT THIS GUIDE ....................................................................................1 Purpose ............................................................................................................................................................... 1 Terms/Usage ....................................................................................................................................................... 1 Overview of this Users Guide............................................................................................................................. 1 INTRODUCTION..........................................................................................2 Applications:........................................................................................................................................................ 2 Supported Features:............................................................................................................................................ 3 Wireless Performance Considerations................................................................................................................ 4 UNPACKING AND SETUP ..............................................................................5 Unpacking............................................................................................................................................................ 5 Setup ................................................................................................................................................................... 5 HARDWARE INSTALLATION ...........................................................................6 Front Panel .......................................................................................................................................................... 6 Rear Panel ........................................................................................................................................................... 7 Side Panel ............................................................................................................................................................ 8 Hanging Way ....................................................................................................................................................... 8 Hardware connections ........................................................................................................................................ 9 Connecting the WLAN Router.......................................................................................................................... 9 Check the installation ...................................................................................................................................... 9 PC NETWORK TCP/IP SETTING...................................................................10 Windows 95/98/ME .......................................................................................................................................... 10 Windows 2000................................................................................................................................................... 11 Windows XP / Vista / 7...................................................................................................................................... 12 CONFIGURATION......................................................................................13 Login to the WLAN Router through Wireless LAN ............................................................................................ 13 Login to the WLAN Router ................................................................................................................................ 13 Using the Web Browser .................................................................................................................................... 13 Setup Wizard ..................................................................................................................................................... 14 Advanced configuration .................................................................................................................................... 23 Main .................................................................................................................................................................. 23 LAN & DHCP Server........................................................................................................................................ 23 WAN ............................................................................................................................................................... 24 Password........................................................................................................................................................ 28 Time ............................................................................................................................................................... 30 Dynamic DNS.................................................................................................................................................. 31 Wireless............................................................................................................................................................. 31 Basic ............................................................................................................................................................... 31 v Security .......................................................................................................................................................... 33 Advanced ....................................................................................................................................................... 35 Wi-Fi Protected Setup.................................................................................................................................... 36 Status................................................................................................................................................................. 37 Device Information ........................................................................................................................................ 37 Log.................................................................................................................................................................. 38 Log Setting ..................................................................................................................................................... 39 Statistic........................................................................................................................................................... 40 Wireless.......................................................................................................................................................... 41 Routing .............................................................................................................................................................. 41 Static .............................................................................................................................................................. 41 Routing Table ................................................................................................................................................. 42 Access ................................................................................................................................................................ 44 Filters ............................................................................................................................................................. 44 Virtual Server ................................................................................................................................................. 48 Special AP....................................................................................................................................................... 49 DMZ................................................................................................................................................................ 50 Firewall Settings............................................................................................................................................. 51 Management..................................................................................................................................................... 52 Remote Management.................................................................................................................................... 52 Tools .................................................................................................................................................................. 54 Restart............................................................................................................................................................ 54 Settings .......................................................................................................................................................... 54 Firmware........................................................................................................................................................ 55 Ping Test......................................................................................................................................................... 56 TECHNICAL SPECIFICATIONS ........................................................................57 LIMITED WARRANTY.................................................................................58 vi ABOUT THIS GUIDE Congratulations on your purchase of this TEW-651BR Wireless Home Router. This integrated access device combines Internet gateway functions with wireless LAN and Fast Ethernet switch. It provides a complete solution for Internet surfing and office resource sharing, and it is easy to configure and operate for every user. Purpose This manual discusses how to install the IEEE 802.11b/g/n Wireless Home Router. Terms/Usage In this guide, the term the WLAN Router refers to your TEW-651BR Wireless Home Router. Overview of this Users Guide Introduction. Describes the TEW-651BR Wireless Home Router and its features. Unpacking and Setup. Helps you get started with the basic installation of the TEW-
651BR Wireless Home Router. Identifying External Components. Describes the front panel, rear panel and LED indicators of the TEW-651BR Wireless Home Router. Connecting the WLAN Router. Tells how you can connect the TEW-651BR Wireless Home Router to your xDSL/Cable Modem. Technical Specifications. Lists the technical (general, physical and environmental, performance and Routers settings) specifications of the TEW-651BR Wireless Home Router. 1 INTRODUCTION With the explosive growth of the Internet, accessing information and services at any time, day or night has become a standard requirement for most people. The era of the standalone PC is waning. Networking technology is moving out of the exclusive domain of corporations and into homes with at least two computers. This integrated access device combines Internet gateway functions with wireless LAN and Fast Ethernet switch. Designed for the business and home, it saves you the cost of installing a separate modem and ISP line for each computer, while providing ready connection for the users, with or without the network wires. Broadband network access is also gaining ground. However, allowing more than two computers to access the Internet at the same time means less affordable, higher costs. Thus, there is a need to share one public IP address over a single Internet connection to link the home with the Internet. The scarcity of IP addresses and using a shared Internet connection through an Internet sharing device can solve high network access costs. All linked computers can make full use of broadband capabilities over such a device. This device not only comes equipped with a wide range of features, but also can be installed and configured right out of the box. This device supports a simple local area network and Internet access share, offering great cost savings. The local area network connects home computers while also allowing any of the computers to access the Internet, share resources, or play online gamesthe basis of the family computing lifestyle. Applications:
Broadband Internet access:
Several computers can share one high-speed broadband connection through wireless or wired (WLAN, LAN and WAN-Internet). Resource sharing:
Share resources such as printers, scanners and other peripherals. File sharing:
Exchange data, messages, and distribute files thus making good use of hard disk space. 2 Online gaming:
Through the local area network, online gaming and e-commerce services can be easily setup. Firewall:
A built-in firewall function for security and anti-hacking systems. Supported Features:
Wi-Fi compliant with IEEE 802.11n and IEEE 802.11b/g standards
4 x 10/100Mbps Auto-MDIX LAN ports 1 x 10/100Mbps WAN port (Internet)
GREENnet technology reduces port-based power consumption
Compatible with most popular cable/DSL Internet service providers using Dynamic/Static IP, PPPoE, PPTP and L2TP
High-speed data rates of up to 150Mbps with IEEE 802.11n*
Wi-Fi Protected Setup (WPS) connects wireless clients at the push of a button Supports 64/128-bit WEP, WPA/WPA2-RADIUS and WPA-PSK/WPA2-PSK Internet Access Control (MAC Address, Domain and IP Filtering) Easy remote management via Web browser Firewall features Network Address Translation (NAT)
Universal Plug and Play (UPnP) and Application Level Gateway support for Internet applications such as email, FTP, gaming, remote desktop, Net Meeting, Telnet and more
Wi-Fi Multimedia (WMM) Quality of Service (QoS) supported
Simple setup via Web browser using the latest version of Internet Explorer, Firefox, and Safari
Works with Windows, Linux, and Mac operating systems
Energy Star certified external power adapter Indoor range up to 100 meters (330 ft.) depending on the environment
Outdoor range up to 300 meters (980 ft.) depending on the environment
3-year limited warranty 3 Wireless Performance Considerations There are a number of factors that can impact the range of wireless devices. 1. Adjust your wireless devices so that the signal is traveling in a straight path, rather than at an angle. The more material the signal has to pass through the more signal you will lose. 2. Keep the number of obstructions to a minimum. Each obstruction can reduce the range of a wireless device. Position the wireless devices in a manner that will minimize the amount of obstructions between them. 3. Building materials can have a large impact on your wireless signal. In an indoor environment, try to position the wireless devices so that the signal passes through less dense material such as dry wall. Dense materials like metal, solid wood, glass or even furniture may block or degrade the signal. 4. Antenna orientation can also have a large impact on your wireless signal. Use the wireless adapters site survey tool to determine the best antenna orientation for your wireless devices. 5. Interference from devices that produce RF (radio frequency) noise can also impact your signal. Position your wireless devices away from anything that generates RF noise, such as microwaves, radios and baby monitors. 6. Any device operating on the 2.4GHz frequency will cause interference. Devices such as 2.4GHz cordless phones or other wireless remotes operating on the 2.4GHz frequency can potentially drop the wireless signal. Although the phone may not be in use, the base can still transmit wireless signal. Move the phones base station as far away as possible from your wireless devices. If you are still experiencing low or no signal consider repositioning the wireless devices or installing additional access points. The use of higher gain antennas may also provide the necessary coverage depending on the environment. 4 UNPACKING AND SETUP This chapter provides unpacking and setup information for the TEW-651BR Wireless Home Router. Unpacking Open the box of the WLAN Router and carefully unpack it. The box should contain the following items:
TEW-651BR Wireless N Home Router
CD-Rom (Users Guide)
Multi-Language Quick Installation Guide
External power adapter
1.5m (5ft) Cat.5 Ethernet Cable If any item is found missing or damaged, please contact your local reseller for replacement. Setup The setup of the WLAN Router can be performed properly using the following methods:
The power outlet should be within 1.82 meters (6 feet) of the Broadband Router.
Visually inspect the DC power jack and make sure that it is fully secured to the power adapter.
Make sure that there is proper heat dissipation and adequate ventilation around the Broadband Router. Do not place heavy objects on the Broadband Router.
Fix the direction of the antennas. Try to place the Wireless Router in a position that can best cover your wireless network. Normally, the higher you place the antenna, the better the performance will be. The antennas position enhances the receiving sensitivity. 5 HARDWARE INSTALLATION Front Panel The figure below shows the front panel of the TEW-651BR Wireless Home Router. Front Panel POWER This indicator lights green when the hub is receives power, otherwise it is off. Status This indicator blinking green means the WLAN Router is working successfully. Otherwise, this indicator always on or off means the function of the WLAN Router has failed. WAN (Link/ACT) The indicators light green when the WAN port is connected to a xDSL/Cable modem successfully. The indicators blink green while the WAN port was transmitting or receiving data from the xDSL/Cable modem. WLAN (ACT) This indicator lights green when there are wireless devices connected and transmitting data to the WLAN Router. LAN (Link/ACT) These indicators light green when the LAN ports were connected successfully. These indicators blinking green while the LAN ports were accessing data. 6 Rear Panel The figure below shows the rear panel of the TEW-651BR Wireless Home Router. Rear Panel Antenna There is one 2dBi gain antenna on the rear panel for wireless connection. LAN (1-4) Four RJ-45 10/100Mbps Auto-MDIX ports for connecting to either 10Mbps or 100Mbps Ethernet connections. WAN In the four port broadband Router, there is an RJ-45 10/100Mbps Auto-MDIX port for the WAN that connects to the xDSL/Cable modem for Internet connectivity. POWER Plug the power adapter to this power jack RESET Use a pin-shaped item to push to reset this device to factory default settings. It will be a useful tool when the manager forgot the password to login, and needs to restore the device back to default settings. 7 Side Panel The figure below shows the side panel of the TEW-651BR Wireless Home Router. WPS (side panel) Push this button to execute the Wi-Fi Protected Setup process. Hanging Way User can mount the device on a wall. Mount the Nylon screw anchors into a cement wall and then drive a screw into the Nylon screw anchors. It does not need to mount the Nylon screw anchors into a wood wall. Hook the mounting holes of the switch back on the screws and completed the wall-mount. 8 Hardware connections Connecting the WLAN Router 1. Plug in one end of the network cable to the WAN port of the WLAN Router. 2. Plug in the other end of the network cable to the Ethernet port of the xDSL or Cable modem. 3. Use another network cable to connect to the Ethernet card on the computer system; the other end of the cable connects to the LAN port of the WLAN Router. Since the TEW-651BR Wireless Home Router has four ports, you can connect up to four computers directly to the unit. Then you do not have to buy a switch to connect these computers since one WLAN Router functions both as a connection-sharing unit and as a switch. Check the installation The control LEDs of the WLAN Router are clearly visible and the status of the network link can be seen instantly:
1. With the power source on, once the device is connected to the broadband modem, the Power, System, LAN, WLAN and WAN port LEDs of the WLAN Router will light up indicating a normal status. 2. When the WAN Port is connected to the ADSL/Cable modem, the WAN LED will light up. 3. When the LAN Port is connected to the computer system, the LAN LED will light up. 9 PC NETWORK TCP/IP SETTING The network TCP/IP settings differ based on the computers operating system
(Win95/98/ME/NT/2000/XP/Vista) and are as follows. Windows 95/98/ME 1. Click on the Network neighborhood icon found on the desktop. 2. Click the right mouse button and a context menu will be show. 3. Select Properties to enter the TCP/IP setting screen. 4. Select Obtain an IP address automatically on the IP address field. 5. Select Disable DNS in the DNS field. 10 6. Select None for the Gateway address field. Windows 2000 Double click on the My Computer icon on the desktop. When My Computer window opens, select Control Panel and then open the Network dialup connection applet. Double click on the Local area network connection icon. Select Properties to enter the TCP/IP setting window. 1. In the Local area network status window, click on Properties. 2. In the Local area network connection window, first select TCP/IP setting and then select Properties. 3. Set both IP address and DNS to Automatic configuration. 11 Windows XP / Vista / 7 Point the cursor and click the right button on the My Network Place icon. Select properties to enter the TCP/IP setting window. 1. Set IP address to Obtain an IP address automatically. 2. Set DNS to Obtain DNS server address automatically. 12 CONFIGURATION First make sure that the network connections are functioning normally. This WLAN Router can be configured using Internet Explorer 5.0 or newer web browser versions. Login to the WLAN Router through Wireless LAN Before configuring the WLAN Router through WLAN, make sure that the SSID, Channel and the WEP is set properly. The default setting of the WLAN Router that you will use:
SSID: TRENDnet651
Channel: Auto Channel
802.11 Mode: 802.11b/g/n mixed mode
Channel bandwidth: 20Mhz
Security: disable Login to the WLAN Router Before you configure this device, note that when the WLAN Router, make sure the host PC must be set on the IP subnet that can be accessed by the xDSL/Cable modem. For example, when the default network address of the xDSL/Cable modem Ethernet interface is 192.168.10.x, then the host PC should be set at 192.168.10.xxx (where xxx is a number between 2 and 254), and the default subnet mask is 255.255.255.0. Using the Web Browser 1. Open Internet Explorer 5.0 or above Internet browser. 2. Enter IP address http://192.168.10.1 (the factory-default IP address setting) to the URL web address location. 3. When the following dialog box appears, enter the user name and password to login to the main configuration window, the default username and password is admin. 13 Setup Wizard Setup wizard is provided as part of the web configuration utility. User can simply follow the step-by-step process to get the wireless Router configuration ready to run in 6 easy steps by clicking on` the Wizard button on the function menu. The following screen will appear. Please click Next to continue. Step 1: Set your new password Setting the new admin password of the WLAN Router. Please click Next to continue. 14 Step 2: Choose time zone Select the time zone from the drop down list. Please click Next to continue. Step 3: Set LAN connection and DHCP server Set users IP address and mask. The default IP is 192.168.10.1. If the user chooses to enable DHCP, please click Enable. DHCP enabled is able to automatically assign IP addresses. Please assign the range of IP addresses in the fields of Range start and Range end. Please click Next to continue. 15 Step 4: Set Internet connection The WLAN Router will attempt to auto detect your Internet Connection. Obtain IP automatically (DHCP client):
If the user has enabled DHCP server, choose "Obtain IP automatically (DHCP client)" to have the WLAN Router assign IP addresses automatically. Fixed IP Address:
16 If the Internet Service Provider (ISP) assigns a fixed IP address, choose this option and enter the assigned WAN IP Address, WAN Subnet Mask, WAN Gateway Address and DNS Server Addresses for the WLAN Router. PPPoE to obtain IP automatically:
If connected to the Internet using a PPPoE (Dial-up xDSL) connection, and the ISP provides a User Name and Password, then choose this option and enter the required information. 17 PPPoE with a fixed IP address:
If connected to the Internet using a PPPoE (Dial-up xDSL) connection and the ISP provides a User Name, Password and a Fixed IP Address, choose this option and enter the required information. 18 PPTP:
If connected to the Internet using a PPTP xDSL connection, enter your IP, Subnet Mask, Gateway, Server IP, PPTP Account and PPTP Password. 19 L2TP:
If connected to the Internet using a L2TP (Dial-up xDSL) connection and the ISP provides a Server IP, Account and Password information, choose this option and enter the required information. 20 Big Pond Cable(Australia):
If your ISP is BigPond Cable, the ISP will provide a User Name, Password, Authentication Server and Login Server IP (Optional). Choose this option and enter the required information. 21 Step 5: Set Wireless LAN connection Click Enable to enable Wireless LAN. If user enables the Wireless LAN, type the SSID in the text box and select a communications channel. The SSID and channel must be the same as wireless devices attempting to connect to the WLAN Router. Step 6: Setup completed The Setup wizard is now completed. The new settings will be effective after the WLAN Router restarts. Please click Restart to reboot the WLAN Router. If user does not want to make any changes, please click Exit to quit without any changes. User also can go back to modify the setting by clicking Back. 22 Advanced configuration Main The screen enables users to configure the LAN & DHCP Server, set WAN parameters, create Administrator and User passwords, and set the local time, time zone, and dynamic DNS. LAN & DHCP Server This page allows the user to configure LAN and DHCP properties, such as the host name, IP address, subnet mask, and domain name. LAN and DHCP profiles are listed in the DHCP table at the bottom of the screen. Host Name: Type the host name in the text box. The host name is required by some ISPs. The default host name is "TEW-651BR". IP Address: This is the IP address of the WLAN Router. The default IP address is 192.168.10.1. Subnet Mask: Type the subnet mask for the WLAN Router in the text box. The default subnet mask is 255.255.255.0. DHCP Server: Enables the DHCP server to allow the WLAN Router to automatically assign IP addresses to devices connecting to the LAN. DHCP is enabled by default. All DHCP client computers are listed in the table at the bottom of the screen, providing the host name, IP address, and MAC address of the client. 23 Start IP: Type an IP address to serve as the start of the IP range that DHCP will use to assign IP addresses to all LAN devices connected to the WLAN Router. End IP: Type an IP address to serve as the end of the IP range that DHCP will use to assign IP addresses to all LAN devices connected to the WLAN Router. Domain Name: Type the local domain name of the network in the text box. This item is optional. Lease Time: The lease time specifies the amount of connection time a network user be allowed with their current dynamic IP address. WAN This screen enables users to set up the WLAN Router WAN connection, specify the IP address for the WAN, add DNS numbers, and enter the MAC address. Connection Type: Select the connection type, either DHCP client, Fixed IP, PPPoE, PPTP, L2TP or BigPond Cable from the drop-down list. 24 DHCP Client or Fixed IP If user has enabled DHCP server, choose "Obtain IP automatically (DHCP client)" to have the router assign IP addresses automatically. WAN IP Address: Select whether user wants to specify an IP address manually, or want DHCP to obtain an IP address automatically. When Specify IP is selected, type the IP address, subnet mask, and default gateway in the text boxes. Users ISP will provide with this information. IP Address: For the Specify mode, enter the specific IP address that provided by your ISP. Subnet Mask: For the Specify mode, enter the specific subnet mask that provided by your ISP. Gateway: For the Specify mode, enter the specific gateway IP address that provided by your ISP. DNS 1/2: Manually specific DNS server IP address; For the Obtain IP Automatically mode, if enter 0.0.0.0 in this filed, the DHCP server will provides DNS server automatically. Clone MAC Address: If your ISP requires you to enter a specific MAC address, please enter it in. The Clone MAC Address button is used to copy the MAC address of your Ethernet adapter to the Router. 25
This product uses the FCC Data API but is not endorsed or certified by the FCC