| submitted | available | document details (if available) | source link |
|---|---|---|---|
| February 05 2014 | February 05 2014 | test 3 Jonathan Adobe PDF Library 10.0 |
| various | User Manual | Users Manual | 1.22 MiB | February 05 2014 |
TRENDnet Users Guide Cover Page TRENDnet Users Guide Contents Product Overview ........................................................................... 1 Package Contents .......................................................................................................... 1 Features ......................................................................................................................... 1 Product Hardware Features........................................................................................... 2 Application Diagram ...................................................................................................... 4 Basic Router Setup .......................................................................... 5 Creating a Home Network ............................................................................................. 5 Router Installation ......................................................................................................... 6 Connect additional wired devices to your network ..................................................... 11 Wireless Networking and Security ................................................. 12 How to choose the type of security for your wireless network .................................. 12 Secure your wireless network ..................................................................................... 13 Connect wireless devices to your router ..................................................................... 15 Connect wireless devices using WPS ........................................................................... 16 Basic wireless settings ................................................................................................. 18 Steps to improve wireless connectivity ....................................................................... 20 Advanced wireless settings .......................................................................................... 21 Access Control Filters .................................................................... 22 Access control basics ................................................................................................... 22 MAC address filters ................................................................................................. 22 Domain/URL Filters ................................................................................................. 23 Protocol/IP filters .................................................................................................... 24 Firewall rules ........................................................................................................... 25 Advanced Router Setup ................................................................. 27 Copyright 2013 TRENDnet. All Rights Reserved. Table of Contents Access your router management page ........................................................................ 27 Change your router login password ............................................................................ 27 Set your router date and time ..................................................................................... 28 Manually configure your Internet connection ............................................................ 28 IPv6 Internet Connection Settings ............................................................................... 29 Clone a MAC address ................................................................................................... 30 Change your router IP address .................................................................................... 31 Set up the DHCP server on your router ....................................................................... 31 Set up DHCP reservation ............................................................................................. 32 Enable/disable UPnP on your router ........................................................................... 33 Allow/deny VPN connections through your router ..................................................... 33 Allow/deny multicast streaming.................................................................................. 34 Identify your network on the Internet ........................................................................ 34 Allow remote access to your router management page ............................................. 35 Open a device on your network to the Internet .......................................................... 35 DMZ ......................................................................................................................... 35 Virtual Server .......................................................................................................... 36 Special Applications ................................................................................................ 38 Add static routes to your router .................................................................................. 39 Enable dynamic routing on your router ...................................................................... 41 Router Maintenance & Monitoring ............................................... 42 Reset your router to factory defaults .......................................................................... 42 Router Default Settings ............................................................................................... 42 Backup and restore your router configuration settings .............................................. 43 Restart your router ...................................................................................................... 45 Check connectivity using the router management page ............................................. 45 Check the router system information ......................................................................... 46 i Table of Contents TRENDnet Users Guide View your router log .................................................................................................... 47 Configure your router log ............................................................................................ 48 View your router packet statistics ............................................................................... 49 View wireless devices connected to your router ......................................................... 49 Capture packets using the router management page ................................................. 50 Enable SNMP on your router ....................................................................................... 50 Router Management Page Structure ............................................. 51 Technical Specifications................................................................. 52 Troubleshooting ............................................................................ 53 Appendix ...................................................................................... 54 Copyright 2013 TRENDnet. All Rights Reserved. ii TRENDnet Users Guide Product Overview TEW-731BR Package Contents In addition to your router, the package includes:
Multi-Language Quick Installation Guide Network cable (1.5m / 5ft.) Power adapter (5V DC, 1A) CD-ROM (Users Guide) If any package contents are missing or damaged, please contact the retail store, online retailer, or reseller/distributor from which the product was purchased. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR Features TRENDnets N300 Wireless Home Router, model TEW-731BR, provides enhanced 300 Mbps wireless n speed and coverage to share files, play games, and stream video wirelessly. Advanced encryption protects your wireless network, Access Control tools help block unwanted Websites and unknown users, and embedded GREENnet technology reduces power consumption by up to 50%. Advanced Multiple Input Multiple Output (MIMO) antenna technology reduces wireless dead spots. Wi-Fi Protected Setup (WPS) connects other WPS supported wireless adapters at the touch of a button. WMM Quality of Service (QoS) technology prioritizes gaming, internet calls, and video streams. LEDs on the front of the router convey device status. Network wired devices to the four Fast Ethernet ports on the back of the router. 4 x 10/100Mbps Auto-MDIX LAN ports 1 x 10/100Mbps Auto-MDIX WAN port (internet) One touch wireless connection to wireless clients using the WPS button Wi-Fi compliant with IEEE 802.11n and IEEE 802.11b/g standards High-speed data rates of up to 300Mbps with IEEE 802.11n*
GREENnet technology reduces power consumption by up to 50%
Compatible with most popular cable / DSL internet service providers using Dynamic / Static IP, PPPoE, PPTP and L2TP protocols Support for IPv6 (Internet Protocol v6) 6rd (IPv6 rapid deployment) DHCPv4, manual and automatic configuration 2 fixed external antennas support high speed performance and great coverage with MIMO technology Firewall features Network Address Translation (NAT) Virtual server and Application Level Gateway (ALG) services for special internet applications Universal Plug and Play (UPnP) for auto discovery and support for device configuration of Internet applications Dynamic DNS Client for dynamic Internet IP resolution Provides additional security with Internet Access Control (MAC Address, Domain, and IP Filtering) Static and Dynamic RIP V1/2 routing support Easy setup via Web browser using Internet Explorer 6.0 or above, Firefox 2.0 or above, Chrome, Opera, Safari Advanced wireless security of up to WPA2-RADIUS Wi-Fi Multimedia (WMM) Quality of Service (QoS) data prioritization 1 TRENDnet Users Guide Indoor coverage up to 100 meters (330 ft.)* depending on the environment Outdoor coverage up to 300 meters (980 ft.)* depending on the environment 3- year limited warranty
*Maximum wireless signal rates are referenced from IEEE 802.11 theoretical specifications. Actual data throughput and coverage will vary depending on interference, network traffic, building materials and other conditions. Product Hardware Features Rear View TEW-731BR Reset Button Use an item such as a paperclip to push and hold this button for 15 seconds and release to reset your router to its factory defaults. LAN Ports Connect Network cables (also called network cables) from your router LAN ports to your wired network devices. WAN PortConnect a Network cable from your router WAN port to your modem. Power Port Connect the included power adapter from your router power port and to an available power outlet. Note: Use only the adapter that came with your router. On/Off Power Switch Push the router On/Off push button to turn your router On (Inner position) or Off (Outer position). Antennas The antennas broadcast wireless network signals. Copyright 2013 TRENDnet. All Rights Reserved. 2 TRENDnet Users Guide Front View TEW-731BR Power LED -This LED indicator is solid green when your router is powered on. Otherwise if this LED indicator is off, there is no power to your router. Status LED - This LED indicator is blinking green when your router is ready and working successfully. If this LED indicator is solid green on or off, your router is not receiving power or not working properly. WAN (Link/Activity) LED This LED indicator is solid green when your router WAN port is physically connected to the modem Network port (also called network port) successfully with a Network cable. The LED indicator will be blinking green while data is transmitted or received through the WAN port of your router. WLAN (Link/Activity) LED This LED indicator is blinking green when the wireless is On and functioning properly on your router. This LED indicator will be blinking green rapidly while data is transmitted or received by your wireless clients or wireless network devices connected to your router. LAN 1-4 (Link/Activity) LEDs These LED indicators are solid green when the LAN ports are successfully connected to your wired network devices (which are turned on). These LED indicators will blink green while data is transmitted or received through your routers LAN ports. Copyright 2013 TRENDnet. All Rights Reserved. 3 TRENDnet Users Guide Side View Application Diagram TEW-731BR The router is installed near the modem (supplied by your ISP Internet Service Provider) and physically connected to the routers WAN port to the modems network port which connects to the Internet. Wireless signals from the router are broadcasted to wireless clients such as laptops (with wireless capability) thereby providing Internet access. 4 WPS (Wi-Fi Protected Setup) Push and hold this button for 3 seconds to activate WPS. The button LED is blinking blue when WPS is activated. Copyright 2013 TRENDnet. All Rights Reserved. TRENDnet Users Guide Basic Router Setup Creating a Home Network What is a network?
A network is a group of computers or devices that can communicate with each other. A home network of more than one computer or device also typically includes Internet access, which requires a router. A typical home network may include multiple computers, a media player/server, a printer, a modem, and a router. A large home network may also have a switch, additional routers, access points, and many Internet-capable media devices such as TVs, game consoles, and Internet cameras. Modem Connects a computer or router to the Internet or ISP (Internet Service Provider). Router Connects multiple devices to the Internet. Switch Connect several wired network devices to your home network. Your router has a built-in network switch (the LAN port 1-4). If you have more wired network devices than available Network ports on your router, you will need an additional switch to add more wired connections. TEW-731BR 3. Set up your router. See How to setup your router below. 4. To connect additional wired computers or wired network devices to your network, see Connect additional wired devices to your network on page 11. 5. To set up wireless networking on your router, see Wireless Networking and Security on page 12. How to setup your router Refer to the Quick Installation Guide or continue to the next section Router Installation on page 6 for more detailed installation instructions. Where to find more help In addition to this Users Guide, you can find help below:
http://www.trendnet.com/support
(documents, downloads, and FAQs are available from this Web page)) How to set up a home network 1. For a network that includes Internet access, youll need:
Computers/devices with a Network port or wireless networking capabilities. A modem and Internet service to your home, provided by your ISP (modem typically supplied by your ISP). A router to connect multiple devices to the Internet. 2. Make sure that your modem is working properly. Your modem is provided by your Internet Service Provider (ISP) when you sign up for Internet service. If your modem is not working contact your ISP to verify functionality. Copyright 2013 TRENDnet. All Rights Reserved. 5 TEW-731BR TRENDnet Users Guide Router Installation Before you Install Many Internet Service Providers (ISPs) allow your router to connect to the Internet without verifying the information fields listed below. Skip this section for now and if your router cannot connect to the Internet using the standard installation process, come back to this page and contact your ISP to verify required ISP specification fields listed below. 1. Obtain IP Address Automatically (DHCP) Host Name (Optional) Clone Mac Address (Optional) 2. Fixed IP address WAN IP Address: _____. _____._____._____
(e.g. 215.24.24.129) WAN Subnet Mask: _____. _____._____._____ WAN Gateway IP Address: _____. _____._____._____ DNS Server Address 1: _____. _____._____._____ DNS Server Address 2: _____. _____._____._____ 3. PPPoE to obtain IP automatically User Name: _________ Password: ________________ Verify Password: ________________ 4. PPPoE with a fixed IP address User Name: _________ Password: ________________ Verify Password: ________________ IP Address: ____. _____._____._____ (e.g. 215.24.24.129) 5. PPTP or Russian PPTP Type (Dynamic IP or Static IP) My IP Address: _____. _____._____._____
(e.g. 215.24.24.129) Subnet Mask:_____. _____._____._____ Gateway:_____. _____._____._____ Server IP: _____. _____._____._____ PPTP Account: ________________ PPTP Password: ________________ Retype Password: ________________ 6. L2TP or Russia L2TP Type (Dynamic IP or Static IP) My IP Address: _____. _____._____._____
(e.g. 215.24.24.129) Subnet Mask:_____. _____._____._____ Gateway:_____. _____._____._____ Server IP: _____. _____._____._____ L2TP Account: ________________ L2TP Password: ________________ Retype Password: ________________ 7. Russia PPPoE Type (Dynamic IP or Static IP) User Name: _________ Password: ________________ Verify Password: ________________ IP Address: ____. _____._____._____ (e.g. 215.24.24.129) Copyright 2013 TRENDnet. All Rights Reserved. 6 TRENDnet Users Guide Hardware Installation 1. Verify that you have an Internet connection when connecting your computer directly to your modem. 5. Using another Network cable, connect the WAN port on the router to your modem. TEW-731BR 2. Turn off your modem. 3. Disconnect the Network cable from your computer to your modem. 4. Using a Network cable, connect your computer to one of the four LAN ports on the router. 6. Plug in the power adapter, connect it to the routers power port, and then push the On/Off Power Switch to the On position (pushed in). 7. Turn on your modem. 8. Verify that the following front panel LED indicators on your router: Power (Solid Green), Status (Blinking Green), LAN 1, 2, 3, or 4 (Solid/Blinking Green for ports for which devices are connected), WAN (Solid/Blinking Green), and WLAN (Blinking Green). Copyright 2013 TRENDnet. All Rights Reserved. 7 TRENDnet Users Guide Setup Wizard 1. Open your web browser (e.g. Internet Explorer, Firefox, Safari, Chrome, or Opera) and go to http://192.168.10.1. Your router will prompt you for a user name and password. 2. Next to Language, click the drop-down list to select your preferred language. Enter the default user name and password and then click Login. Default User Name: admin Default Password: admin TEW-731BR 3. The Setup Wizard will automatically appear. Click Next. Note: If the Setup Wizard does not automatically appear, click Wizard (the bottom button on the left tab). 4. Enter a new login password for your router and enter it again next to Verify Password to confirm. This will change the password required to log into your router. Click Next. Note: This is the password to enter your routers management interface and NOT to connect to the router wirelessly. Once you change the login password, it will be required every time you log into your router. Store your router password in a location that you can reference at a future time. Copyright 2013 TRENDnet. All Rights Reserved. 8 TRENDnet Users Guide 5. Select the Time Zone for your router and click Next. 6. Click Next at the Set LAN connection and DHCP Server window. Note: If you are an advanced user, you can make LAN IP address interface and DHCP IP address range changes here. TEW-731BR 7. This section determines what method the router will use to interface with your ISP service. Most ISP services allow your router to obtain an IP address automatically. Do not change the default setting of Obtain IP Automatically and click next to proceed. Note: If you know that your ISP requires a configuration other than Obtain IP Automatically or if are having difficulty completing the router installation, please contact your ISP to verify all required settings for one of the options listed on page 6. The options listed on page 6 match the settings options available to choose from. Copyright 2013 TRENDnet. All Rights Reserved. 8. Wireless LAN: Select Enable for Wireless LAN. Note: Selecting Disable will disable the wireless functionality of the router and will not allow wireless clients to connect. 9 TRENDnet Users Guide 9. SSID: Enter a unique SSID (Wireless Network Name). Choose something that you would easily identify when searching for available wireless networks (using laptops, smart phones, etc.) Click Next. Note:
1. To protect your network from unauthorized access, it is recommended to enable wireless encryption. See Secure your wireless network on page 13 for information on configuring wireless security. 2. Once wireless security is enabled on your router, each wireless device connecting to your router must be configured with the same wireless security type and key. 10. Click Restart and wait for your router to reboot. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR 11. Wait for your router to reboot. 12. Verify you have an Internet connection by opening a Web browser on your computer. Note: If you cannot access the Internet, power down your modem and router again. Occasionally certain modems need to be power cycled to adopt new router settings. 10 TRENDnet Users Guide Connect additional wired devices to your network You can connect additional computers or other network enabled devices to your network by using Network cables. Connect them to one of the available LAN ports labeled 1,2,3,4 on your router. Check the status of the LED indicators (1, 2, 3, or 4) on the front panel of your router to ensure the physical cable connection from your computer or device. Note: If you encounter issues connecting to your network, there may be a problem with your computer or device network settings. Please ensure that your computer or device network settings (also called TCP/IP settings) are configured to obtain IP address settings automatically (also called dynamic IP address or DHCP) and to Obtain DNS Server address settings automatically. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR 11 TRENDnet Users Guide Wireless Networking and Security How to choose the type of security for your wireless network Setting up wireless security is very important. Leaving your wireless network open and unsecure could expose your entire network and personal files to outsiders. TRENDnet recommends reading through this entire section and setting up wireless security on your new router. There are a few different wireless security types supported in wireless networking each having its own characteristics which may be more suitable for your wireless network taking into consideration compatibility, performance, as well as the security strength along with using older wireless networking hardware (also called legacy hardware). It is strongly recommended to enable wireless security to prevent unwanted users from accessing your network and network resources (personal documents, media, etc.). In general, it is recommended that you choose the security type with the highest strength and performance supported by the wireless computers and devices in your network. Please review the security types to determine which one you should use for your network. Wireless Encryption Types WEP: Legacy encryption method supported by older 802.11b/g hardware. This is the oldest and least secure type of wireless encryption. It is generally not recommended to use this encryption standard, however if you have old 802.11 b or 802.11g wireless adapters or computers with old embedded wireless Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR cards(wireless clients), you may have to set your router to WEP to allow the old adapters to connect to the router. Note: This encryption standard will limit connection speeds to 54Mbps. WPA: This encryption is significantly more robust than the WEP technology. Much of the older 802.11g hardware was been upgraded (with firmware/driver upgrades) to support this encryption standard. Total wireless speeds under this encryption type however are limited to 54Mbps. WPA-Auto: This setting provides the router with the ability to detect wireless devices using either WPA or WPA2 encryption. Your wireless network will automatically change the encryption setting based on the first wireless device connected. For example, if the first wireless client that connects to your wireless network uses WPA encryption your wireless network will use WPA encryption. Only when all wireless clients disconnect to the network and a wireless client with WPA2 encryption connects your wireless network will then change to WPA2 encryption. NOTE: WPA2 encryption supports 802.11n speeds and WPA encryption will limit your connection speeds to 54Mbps WPA2: This is the most secure wireless encryption available today, similar to WPA encryption but more robust. This encryption standard also supports the highest connection speeds. TRENDnet recommends setting your router to this encryption standard. If you find that one of your wireless network devices does not support WPA2 encryption, then set your router to either WPA or WPA-Auto encryption. Note: Check the specifications of your wireless network adapters and wireless appliances to verify the highest level of encryption supported. 12 TRENDnet Users Guide TEW-731BR Compatible Wireless Standards Highest Performance Under This Setting Encryption Strength Additional Options Below is brief comparison chart of the wireless security types and the recommended configuration depending on which type you choose for your wireless network. Security Standard WPA2 WPA WEP IEEE 802.11a/b/g/n
(802.11n devices will operate at 802.11g speeds) IEEE 802.11a/b/g/n
(802.11n devices will operate at 802.11g speeds) IEEE 802.11a/b/g/n Up to 54Mbps Up to 54Mbps Up to 450Mbps*
Low Open System or Shared Key, HEX or ASCII, Different key sizes Open System ASCII 13 characters Medium TKIP or AES, Preshared Key or RADIUS TKIP Preshared Key 8-63 characters High TKIP or AES, Preshared Key or RADIUS AES Preshared Key 8-63 characters Recommended Configuration
*Dependent on the maximum 802.11n data rate supported by the device (150Mbps, 300Mbps, or 450Mbps) Copyright 2013 TRENDnet. All Rights Reserved. Secure your wireless network Wireless > Security After you have determined which security type to use for your wireless network (see How to choose the security type for your wireless network on page 12), you can set up wireless security. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Wireless, and click on Security. 3. Click on the Authentication Type drop-down list to select your wireless security type. 13 TRENDnet Users Guide Selecting WEP:
If selecting WEP (Wired Equivalent Privacy), please review the WEP settings to configure and click Apply to save the changes. WEP Choose Open System or Shared Key. Note: It is recommended to use Open System because it is known to be more secure than Shared Key. Mode Choose HEX or ASCII. Note: It is recommended to use ASCII because of the much larger character set that can be used to create the key. WEP Key Choose the key length 64-bit or 128-bit. Note: It is recommended to use 128-bit because it is more secure to use a key that consists of more characters. Key 1-4 connect to the router wirelessly o This is where you enter the password or key needed for a computer to o You can define up to 4 passwords or 4 keys. Only one key can be active at a given time. Most users simply define one key. o Choose a key index 1, 2, 3, or 4 and enter the key. o When connecting to the router, the client must match both the password and the Key number. (e.g. if you have activated Key 2 with a Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR password of 12345, then the client must select: Key 2 (entering Key 1, 3, or 4 will block the ability to connect) and enter password 12345) Selecting WPA, WPA-Auto, or WPA2 (WPA2 recommended):
First, from the Authentication Type row, select WPA, WPA-Auto, or WPA2. Then from the PSK/EAP row, select either PSK or EAP PSK stands for Preshared Key EAP stands for Extensive Authentication Protocol, also called Remote Authentication Dial-In User Service or RADIUS). Note: EAP requires an external RADIUS server, PSK only requires you to create a passphrase. The following section outlines options when selecting PSK (Preshared Key Protocol), WEP Key Format HEX ASCII Character set 64-bit key length 128-bit key length 0-9 & A-F, a-f only 10 characters 26 characters Alphanumeric (a,b,C,?,*, /,1,2, etc.) 5 characters 13 characters Select a Cipher Type. When selecting WPA security, it is recommended to use TKIP. o o When selecting WPA-Auto security, it is recommended to use AES. o When selecting WPA2 security, it is recommended to use AES. 14 TRENDnet Users Guide Create your Wireless security Passphrase (password or key):
Passphrase Enter the passphrase. o This is the password or key that is used to connect your computer to this router wirelessly Confirmed Passphrase Re-enter the passphrase. Note: 8-63 alphanumeric characters (a,b,C,?,*, /,1,2, etc.) The following section outlines options when selecting EAP (Extensive Authentication Protocol), EAP (Extensible Authentication Protocol) is also called Remote Authentication Dial-In User Service or RADIUS. Select a Cipher Type o When selecting WPA security, it is recommended to use TKIP. o When selecting WPA-Auto security, it is recommended to use AES. o When selecting WPA2 security, it is recommended to use AES. RADIUS Server 1/2 - Configure the RADIUS server settings. TEW-731BR Note: RADIUS Server 2 is optional and can be configured as a backup if there are any issues with RADIUS Server 1. IP Enter the IP address of the RADIUS server. (e.g. 192.168.10.250) o o Port Enter the port your RADIUS server is configured to use for RADIUS authentication. Note: It is recommended to use port 1812. o Shared Secret Enter the shared secret used to authorize your router with your RADIUS server. Connect wireless devices to your router A variety of wireless network devices can connect to your wireless network such as:
Gaming Consoles Internet enabled TVs Network media players Smart Phones Wireless Laptop computers Wireless IP cameras Each device may have its own software utility for searching and connecting to available wireless networks, therefore, you must refer to the Users Manual/Guide of your wireless client device to determine how to search and connect to this routers wireless network. See the Appendix on page 54 for general information on connecting to a wireless network. Copyright 2013 TRENDnet. All Rights Reserved. 15 TRENDnet Users Guide Connect wireless devices using WPS WPS (Wi-Fi Protected Setup) is a feature that makes it easy to connect devices to your wireless network. If your wireless devices support WPS, you can use this feature to easily add wireless devices to your network. Note: You will not be able to use WPS if you set the SSID Broadcast setting to Disabled. There are two methods the WPS feature can easily connect your wireless devices to your network. Push Button Configuration (PBC) method o RECOMMENDED Hardware Push Button methodwith an external button located physically on your router and on your client device o WPS Software/Virtual Push Button - located in router management page PIN (Personal Identification Number) Method - located in router management page Note: Refer to your wireless device documentation for details on the operation of WPS. Recommended Hardware Push Button (PBC) Method Note it is recommended that a wireless key (passphrase or password) is created before connecting clients using the PBC method. If no wireless key is defined when connecting via PBC, the router will automatically create an encryption key that is 64 characters long. This 64 character key will then have to be used if one has to connect computers to the router using the traditional connection method. To add a wireless device to your network, simply push the WPS button on the wireless device you are connecting(consult client device Users Guide for length of time), then push and hold the WPS button located on your router for 3 seconds and release it. A blue LED on your router WPS button will flash indicating that the WPS setup process has been activated on your router. (See Product Hardware Features on page 2) For connecting additional WPS supported devices, repeat this process for each additional device. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR PBC (Software/Virtual Push Button) Wireless >WiFi Protected Setup In addition to the hardware push button located physically on your router, the router management page also has push button which is a software or virtual push button you can click to activate WPS on your router. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Wireless, and click on WPS. 3. To add a wireless device to your network, simply the push the WPS button on the wireless device (consult wireless devices Users Guide for length of time), you are connecting, then in your router management page next to Push Button Configuration, click Start PBC. 4. You will receive a message counting down indicating the WPS process is activated on your router. 5. You will receive a success message indicate that the wireless device successfully connected using WPS. 16 TRENDnet Users Guide PIN (Personal Identification Number) Wireless >WiFi Protected Setup If your wireless device has WPS PIN (typically an 8-digit code printed on the wireless device product label or located in the wireless device wireless software utility), you can use this method. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Wireless, and click on WPS. 3. Next to Client PIN Number, enter the WPS PIN of the wireless device you are connecting and click Start PIN. Note: You may need to initiate the WPS PIN on your wireless device first when using this method. Refer to your wireless device documentation for details on the operation of WPS. TEW-731BR WPS PIN Security Wireless >WiFi Protected Setup To protect your wireless network against WPS PIN attacks, the WPS Auto Lock Down State feature will automatically disable the WPS PIN method after 10 failed WPS PIN attempts. Once lock down state is activated, the WPS PIN method will be disabled until you access the router management page and unlock it. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Wireless, and click on WPS. 3. If Auto-lock-down-state is activated, the status will display as Locked. To unlock this state and re-enable WPS PIN method, click Unlock. 4. To save changes, click Apply. Copyright 2013 TRENDnet. All Rights Reserved. 17 TRENDnet Users Guide Basic wireless settings Wireless > Basic This section outlines available management options under the Basic Wireless sub tab. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Wireless, and click on Basic. 3. To save changes to this section, click Apply when finished. Wireless o Enabled turns on the wireless networking on your router (by default it is enabled). o Disabled turns off wireless networking on your router. Note: It is recommended to leave the wireless setting to Enabled unless you do not plan on connecting any wireless computers or devices to your network. SSID This acronym stands for Service Set Identifier and is the name of your wireless network. It differentiates your wireless network from others around you. By default, the router broadcast TRENDnet731 as the wireless network name. If you choose to change the SSID, change it to a name that you can easily remember. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR Auto Channel In North America, this router can broadcast on 1 of 11 Channels (13 in Europe and other countries). Selecting Auto Channel enables the router to automatically select the best Channel for wireless communication. Channel To manually set the channel on which the router will broadcast, uncheck Auto Channel, then click the drop-down list and select the desired Channel for wireless communication. The goal is to select the Channel that is least used by neighboring wireless networks. 802.11 Mode - Select the appropriate mode for your network. o 2.4GHz 802.11b/g/n mixed mode Select this mode for the best compatibility. This mode allows older 802.11b and 802.11g wireless devices to connect to the router in addition to newer 802.11n devices. o 2.4GHz 802.11b/g mixed mode This mode only allows devices to connect to the router using older and slow 802.11b or 802.11g technology and it thereby reduces the routers maximum speed to 54Mbps (typically not recommended). o 2.4GHz 802.11n only mode This mode only allows newer 802.11n devices to connect to your router. This mode does ensure the highest speed and security for your network, however if you have older 802.11g wireless clients, they will no longer be able to connect to this router. 18 TRENDnet Users Guide o 2.4GHz 802.11g only mode This mode only allows devices to connect to the router using older and slow 802.11g technology
(typically not recommended). o 2.4GHz 802.11b only mode This mode only allows devices to connect to the router using older and slow 802.11b technology
(typically not recommended). Note: Please check the specifications on your wireless devices for the highest wireless capability supported first before applying these settings. If you are unsure, it is recommended that you keep the default setting (2.4GHz 802.11b/g/n mixed mode) for the best compatibility. When applying the 802.11 mode setting, please keep in mind the following:
Wireless devices that support 802.11n are backwards compatible and can connect wirelessly at 802.11g or 802.11b. Connecting at 802.11b or 802.11g will limit the capability of your 802.11n supported wireless devices from obtaining higher performance and data rates. Allowing 802.11b or 802.11g devices to connect to an 802.11n capable wireless network may degrade the wireless network performance below the higher performance and data rates of 802.11n. Wireless devices that only support 802.11b or 802.11g will not be able to connect to a wireless network that is set to 802.11n only mode. Wireless devices that only support 802.11b will not be able to connect to a wireless network that is set to 802.11g only mode. Channel Width This setting only applies to wireless devices connecting at 802.11n. Select the appropriate channel width for your wireless network. o 20 MHz This mode operates using a single 20MHz channel for wireless devices connecting at 802.11n. This setting may provide more TEW-731BR stability than Auto 20/40 MHz for connectivity in busy wireless environments where there are several wireless networks in the area. o Auto 20/40 MHz This mode can automatically switch between using a single 20MHz channel or 40MHz (two 20MHz channels). When 40MHz is active, this mode is capable of providing higher performance only if the wireless devices support the 40MHz channel width. Enabling 20/40MHz typically results in substantial performance increases when connecting to an 802.11n client. SSID Broadcast o Enabled allows wireless devices to search and discover your wireless network name (also called SSID) broadcasted by your router. o Disabled turns off the ability for wireless devices to find your network. It is still possible for wireless devices to be configured to connect to your wireless network. Note: Setting this option to Disabled, will disable WPS functionality. WMM Wi-Fi Multimedia is a Quality of Service (QoS) feature which prioritizes audio and video data packets. This feature requires the wireless device to also support WMM. Click Enabled (recommended) or Disabled to turn this feature on or off on your router. Copyright 2013 TRENDnet. All Rights Reserved. 19 TRENDnet Users Guide Steps to improve wireless connectivity There are a number of factors that can impact the range of wireless devices. Follow these tips to help improve your wireless connectivity:
1. Keep the number of obstructions to a minimum. Each obstruction can reduce the range of a wireless device. Position the wireless devices in a manner that will minimize the amount of obstructions between them. a. For the widest coverage area, install your router near the center of your home, and near the ceiling, if possible. b. Avoid placing the router on or near metal objects (such as file cabinets and metal furniture), reflective surfaces (such as glass or mirrors), and masonry walls. c. Any obstruction can weaken the wireless signal (even non-metallic objects), so the fewer obstructions between the router and the wireless device, the better. d. Place the router in a location away from other electronics, motors, and fluorescent lighting. e. Many environmental variables can affect the routers performance, so if your wireless signal is weak, place the router in several locations and test the signal strength to determine the ideal position. 2. Building materials can have a large impact on your wireless signal. In an indoor environment, try to position the wireless devices so that the signal passes through less dense material such as dry wall. Dense materials like metal, solid wood, glass or even furniture may block or degrade the signal. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR 3. Antenna orientation can also have a large impact on your wireless signal. Use the wireless adapters site survey tool to determine the best antenna orientation for your wireless devices. 4. Interference from devices that produce RF (radio frequency) noise can also impact your signal. Position your wireless devices away from anything that generates RF noise, such as microwaves, radios and baby monitors. If possible, upgrade wireless network interfaces (such as wireless cards in computers) from older wireless standards to 802.11n. If a wirelessly networked device uses an older standard, the performance of the entire wireless network may be slower. If you are still experiencing low or no signal consider repositioning the wireless devices or installing additional access points. 20 TEW-731BR Fragmentation Threshold Fragmentation in wireless networks is the process of breaking down data communications into smaller data packets in order to improve data efficiency when transferring or receiving data between wireless devices. The fragmentation threshold defines the maximum size of the data packets that are broken down. Default Value: 2346 (range: 1500~2346, even numbers only) DTIM Interval A Delivery Traffic Indication Message (DTIM) is an informational message that is sent as part of a beacon by an access point (your wireless router) to a wireless client (wireless device or connecting station) in sleep mode to provide an alert that data is awaiting delivery. The DTIM Interval
(also called Data Beacon Rate) is the amount of time between DTIM transmissions included in part of a beacon. Default Value: 1 (range: 1-255) TRENDnet Users Guide Advanced wireless settings Wireless > Advanced These settings are advanced options that can be configured to change advanced wireless broadcast specifications. It is recommended that these settings remain set to their default values unless you are knowledgeable about the effects of changing these values. Changing these settings incorrectly can degrade performance. Beacon Interval A beacon is a management frame used in wireless networks that transmitted periodically to announce the presence and provide information about the routers wireless network. The interval is the amount time between each beacon transmission. Default Value:100 milliseconds (range: 25-1000) RTS Threshold The Request To Send (RTS) function is part of the networking protocol. A wireless device that needs to send data will send a RTS before sending the data in question. The destination wireless device will send a response called Clear to Send (CTS). The RTS Threshold defines the smallest data packet size allowed to initiate the RTS/CTS function. Default Value: 2346 (range: 256-2346) Copyright 2013 TRENDnet. All Rights Reserved. 21 TRENDnet Users Guide Access Control Filters Access control basics Access > Filter MAC address filters Access > Filter > MAC Filters Every network device has a unique, 12-digit MAC (Media Access Control) address. Using MAC filters, you can allow or deny specific computers and other devices from using this routers wired or wireless network. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Access, click on Filter, and click on MAC Filters. 3. Add the MAC addresses to the MAC Table first before applying the MAC filter function. Note: MAC filter can be configured to allow access to the listed MAC address and deny all others unlisted or vice versa. The recommended function is to choose to only allow access to the MAC addresses listed and deny all others unlisted because it is easier to determine the MAC addresses of devices in your network then to determine which MAC addresses you do not want to allow access. Name Enter a name for the MAC address entry. MAC Address Enter the 12-digit MAC address.(e.g. 00-11-22-AA-BB-CC) Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR Note: You can check the Dynamic DHCP List for the MAC addresses of the devices on your network, see Setup the DHCP server on your router on page 31 or refer to your computer or device documentation to find the MAC address. Click Add to save the new MAC address entry to the MAC Table. After clicking Add, the MAC address entry will appear in the list below. Repeat for each device. Add Saves a new MAC address entry. To modify an existing MAC address entry, click on the entry in the MAC Table. When selected, the entry will be highlighted. Delete Removes an existing MAC address entry. Update Modifies an existing MAC address entry. Cancel Discard changes to an existing MAC address entry. 22 TRENDnet Users Guide 4. Review the MAC Filter options. Disabled disables MAC address filter. Only Allow computers/devices with MAC addresses listed below to access the local network (LAN/WLAN), web management, and the Internet. Only Deny computers/devices with MAC addresses listed below to access the local network (LAN/WLAN), web management, and the Internet Note: Do not configure this setting until you have added the MAC addresses to the MAC Table first. The recommended option is to only Allow access to the MAC addresses listed and deny all others unlisted. TEW-731BR Domain/URL Filters Access > Filter > Domain/URL Blocking You may want to allow or block computers or devices on your network access to specific websites (e.g. www.trendnet.com, etc.), also called domains or URLs (Uniform Resource Locators). You may also enter a keyword (e.g. instead of complete URL to generally allow or block computers or devices access to websites that may contain the keyword in the URL or on the web page. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Access, click on Filter, and click on Domain/URL Blocking. Click Apply to save the changes. 3. Review the Domain/URL blocking options. Disabled disables domain/URL blocking Allow users to access all domains listed.
(Deny access to all other unlisted websites) Deny users to access all domains listed.
(Allow access to all other unlisted websites) Copyright 2013 TRENDnet. All Rights Reserved. 23 TRENDnet Users Guide Click Apply to save the changes. 4. Under Domain Blocking click on Allow or Deny. The Domains List will then appear. Enter the Website/URL/domain (e.g.www.trendnet.com) or keyword (e.g. trendnet) to allow or block access and click Add to add this to the domains list. The entry will be listed below. Repeat for each additional website or keyword added. Cancel - Discard changes to the domains list. Delete -Delete an existing website/URL/domain or keyword entry, click on the entry in the Domains List. When selected, the entry will be highlighted. Click Delete to remove it from the list. TEW-731BR Protocol/IP filters Access > Filter > Protocol/IP Filters You may want to block computers or devices on your network access to specific ports
(used or required by a specific application) to the Internet. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Access, click on Filter, and click on Protocol/IP Filters. To simplify configuration, there is a list of commonly used pre-defined Protocol/IP Filters to modify otherwise, you can choose to manually add a new Protocol/IP Filter. 4. Go back to the Domain Blocking section and confirm you want to Allow or Deny access to the Domains List. It is generally easier to manage a list of Domains for which access is denied. 5. In Domain Blocking click on Apply to save the selected settings. Copyright 2013 TRENDnet. All Rights Reserved. 3. Review the protocol/IP filter settings. Enabled Selecting Enabled turns on the Protocol/IP Filter and selecting Disabled turns it off. Name Enter a name for the Protocol/IP Filter. 24 TRENDnet Users Guide Protocol Select the protocol type to filter. TCP, UDP, or you can select * to choose all protocol types. Port Enter the port number or port range numbers to block. (e.g. 80-80 or 20-
21). IP Range Enter the IP address or IP address range to apply the protocol/IP filter. (e.g. 192.168.10.20-192.168.10.20 or 192.168.10.20-192.168.10.30). Note: The filter will not be applied to IP addresses outside of the range specified. Add Saves new protocol/IP filter. To modify an existing protocol/IP filter, click on the entry in the Protocol/IP Filters list. When selected, the entry will be highlighted. Delete Removes an existing protocol/IP filter. Update Modifies an existing protocol/IP filter. Cancel Discard changes to an existing protocol/IP filter. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR Firewall rules Access > Firewall Rule You may want specify inbound or outbound access control to allow/deny sources (or Internet IP addresses) to your network from the Internet or from computers or devices on your network to the Internet. Firewall rules may allow for more granular control of specific inbound and outbound access between your network and the Internet. It is recommended that these settings remain set to default unless you are knowledgeable about the effects of changing the firewall rule configuration. It is possible to have undesirable functionality from your router if these settings are improperly modified. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Access, click on Filter, and click on Firewall Rule. 3. In the list, there are two default rules specific which cannot be modified. One rule to deny all access from the Internet to your network for security and the other to allow all access from your network to the Internet. Any additional rules will take precedence over the default rules. 25 TRENDnet Users Guide 4. Review the firewall rule settings. TEW-731BR Enabled Selecting Enabled turns on the firewall ruler and selecting Disabled turns it off. Name Enter a name for the firewall rule. Action Select Allow will allow access and selecting Deny will block or deny access. Source Configure the source information for the firewall rule. o o o Interface - Click the drop-down list and select LAN (from your network) or WAN (from the Internet) depending on where the traffic will be coming from. IP Range Start Changes the starting address for the firewall rule to apply (e.g. 192.168.1.20) IP Range End Changes the last address for the firewall rule to apply
(e.g. 192.168.1.30) Note: The IP Range Start and End specify the range of IP addresses that the firewall rule will apply. Both fields need to be completed so use the same value to specify a single IP address. Destination Configure the destination information for the firewall rule. o o o Interface - Click the drop-down list and select LAN (your network) or WAN (Internet) depending on where the traffic will be coming from. IP Range Start Changes the starting address for the firewall rule to apply (e.g. 192.168.10.20) IP Range End Changes the last address for the firewall rule to apply
(e.g. 192.168.10.30) Note: The IP Range Start and End specify the range of IP addresses that the firewall rule will apply. Both fields need to be completed so use the same value to specify a single IP address. o Protocol Select the protocol type to filter. TCP, UDP, ICMP, or you can select * to choose all protocol types. Below, enter the port number or range of port numbers to apply the firewall rule. (e.g. 80-80 or 20-21). For all ports, use the port range 1 - 65534. Copyright 2013 TRENDnet. All Rights Reserved. Add Saves new firewall rule. Update Modifies an existing firewall rule. Delete Removes an existing firewall rule. New -Saves new firewall rule. Cancel Discard changes to an existing firewall rule. Priority Up Moves an existing firewall rule one step higher in priority. Priority Down Moves an existing firewall rule one step below in priority. Update Priority Save updated changes to priority. Note: Top position in the list is the highest priority, bottom position in the list is the lowest priority. To modify an existing firewall rule, click on the rule in the firewall rules list. When selected, the entry will be highlighted. 26 TRENDnet Users Guide Advanced Router Setup Access your router management page Note: Your router management page http://192.168.10.1 is accessed through the use of your Internet web browser (e.g. Internet Explorer, Firefox, Chrome, Safari, Opera) and will be referenced frequently in this Users Guide. 1. Open your web browser (e.g. Internet Explorer, Firefox, Safari, Chrome, or Opera) and go to http://192.168.10.1. Your router will prompt you for a user name and password. 2. Next to Language, click the drop-down list to select your preferred language. Enter the default user name and password and then click Login. Default User Name: admin Default Password: admin TEW-731BR Change your router login password Main > Password 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Main, and click on Password. 3. Under the Administrator section, in the New Password field, enter the new password, and in the Confirm Password field, retype the new password again to confirm. 4. To save changes, click Apply. Note: If you change the router login password, you will need to access the router management page using the User Name admin and the new password instead of the default password admin. Copyright 2013 TRENDnet. All Rights Reserved. 27 TRENDnet Users Guide TEW-731BR User (Optional): The User account is an additional account used for viewing the settings on the router management page only. Accessing the router management page using the User account will restrict access to viewing only and will not allow any settings to be changed. Default User Name: user Default Password: user Set your router date and time Main > Time 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Main, and click on Time. 3. Next to Time Zone, click the drop-down list to select your Time Zone. 4. Next to Synchronize the clock with, you can choose one of the following options:
Manual Set your router date and time manually in the Set Time section. To save changes, click Apply. Note: Time is specified in 24-hour format. OR Automatic Set your router date and time to synchronize with an NTP
(Network Time Protocol) server address (e.g. pool.ntp.org). Enter the NTP server address next to Default NTP server, (e.g. pool.ntp.org). Next to Daylight Saving, set the annual range when daylight saving is activated. To save changes, click Apply. Note: NTP servers are used for computers and other network devices to synchronize time across an entire network. Copyright 2013 TRENDnet. All Rights Reserved. 5. You can verify the time/date settings next to Local Time at the top of the page. Local Time displays the current date and time set on your router. Manually configure your Internet connection Main > WAN 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Main, and click on WAN. 3. In the Connection Type drop-down list, click the type of Internet connection provided by your Internet Service Provider (ISP). 4. Complete the fields required by your ISP. 5. Complete the optional settings only if required by your ISP. 28 TRENDnet Users Guide 6. To save changes, click Apply. Note: If you are unsure which Internet connection type you are using, please contact your ISP. Note: If your ISP requires a host name to be specified, you can specify it under Main > LAN & DHCP Server, in the Host Name field. To save changes, click Apply at bottom of the page. IPv6 Internet Connection Settings Main > IPv6 IPv6 (Internet Protocol Version 6) is a new protocol that significantly increases the number of available Internet public IP addresses due to the 128-bit IP address structure versus IPv4 32-bit address structure. In addition, there are several integrated enhancements compared to the most commonly used and well known IPv4 (Internet Protocol Version 4) such as:
Integrated IPsec Better Security Integrated Quality of Service (QoS) Lower latency for real-time applications Higher Efficiency of Routing Less transmission overhead and smaller routing tables Easier configuration of addressing Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR Note: In order to use IPv6 Internet connection settings, it is required that your ISP provide you with the IPv6 service. Please contact your ISP for availability and more information about the IPv6 service. 1. Review the IPv6 Internet Connection settings and enter information settings specified by your ISP. IPv6 Automatic Select Enabled for automatic configuration of your IPv6 address settings. Otherwise, if it is required to manually configure the parameters provided by your ISP, select Disabled. 6rd Configuration Select the appropriate option according to the parameters specified by your ISP. IPv4 Address Displays the IPv4 address automatically provided by your ISP. To manually configure the IPv4 address settings, click on Main > WAN and configure your IPv4 settings. Mask Length Enter the IPv4 mask length used for the tunnel provided by your ISP. Assigned IPv6 Prefix Displays the IPv6 address automatically provided by your ISP. 29 TRENDnet Users Guide Tunnel Link-Local Address Displays the IPv6 local link WAN (Internet) interface address. 6rd Border Relay IPv4 Address Enter the IPv4 relay address used for the tunnel provided by your ISP. Primary IPv6 DNS Server Enter the primary IPv6 DNS server address provided by your ISP. Secondary IPv6 DNS Server Enter the secondary IPv6 DNS server address provided by your ISP. TEW-731BR 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Main, and click on WAN. 3. Under your Internet connection settings, find the MAC Address section shown below. 2. To save changes, click Apply. 4. Click either Clone MAC Address to clone the MAC address of the computer you are currently using or manually enter the 12-digit MAC address of your old router. 5. To save changes, click Apply. Clone a MAC address Main > WAN On any home network, each network device has a unique MAC (Media Access Control) address. Some ISPs register the MAC address of the device (usually a router or a computer) connected directly to the modem. If your computer MAC address is already registered with your ISP and to prevent the re-provisioning and registration process of a new MAC address with your ISP, then you can clone the address (assign the registered MAC address of your previous device to your new router). If you want to use the MAC address from the previous device (computer or old router that directly connected to the modem, you should first determine the MAC address of the device or computer and manually enter it into your router using the clone MAC address feature. Note: For many ISPs that provide dynamic IP addresses automatically, typically, the stored MAC address in the modem is reset each time you restart the modem. If you are installing this router for the first time, turn your modem before connecting the router to your modem. To clear your modem stored MAC address, typically the procedure is to disconnect power from the modem for approximately one minute, then reconnect the power. For more details on this procedure, refer to your modems User Guide/Manual or contact your ISP. Copyright 2013 TRENDnet. All Rights Reserved. 30 TRENDnet Users Guide Change your router IP address Main > LAN & DHCP Server In most cases, you do not need to change your router IP address settings. Typically, the router IP address settings only needs to be changed, if you plan to use another router in your network with the same IP address settings, if you are connecting your router to an existing network that is already using the IP address settings your router is using, or if you are experiencing problems establishing VPN connections to your office network through your router. Note: If you are not encountering any issues or are not faced with one of the cases described above or similar, it is recommended to keep your router IP address settings as default. Default Router IP Address: 192.168.10.1 Default Router Network: 192.168.10.0 / 255.255.255.0 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Main, and click on LAN & DHCP Server. 3. Enter the router IP address settings. IP Address Enter the new router IP address.
(e.g. 192.168.200.1) Subnet Mask Enter the new router subnet mask.
(e.g. 255.255.255.0) Note: The DHCP address range will change automatically to your new router IP address settings so you do not have to change the DHCP address range manually to match your new router IP address settings. TEW-731BR 4. To save changes, click Apply. Note: You will need to access your router management page using your new router IP address to access the router management page. (e.g. Instead of using the default http://192.168.10.1 using your new router IP address will use the following format using your new router IP address http://(new.router.ipaddress.here) to access your router management page. Set up the DHCP server on your router Main > LAN & DHCP Server Your router can be used as a DHCP (Dynamic Host Configuration Protocol) server to automatically assign an IP address to each computer or device on your network. The DHCP server is enabled by default on your router. If you already have a DHCP server on your network, or if you do not want to use your router as a DHCP server, you can disable this setting. It is recommended to leave this setting enabled. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Main, and click on LAN & DHCP Server. 3. Review the DHCP Server settings. DHCP Server Enable or Disable the DHCP server. Start IP Changes the starting address for the DHCP server range. (e.g. 192.168.10.20) End IP Changes the last address for the DHCP server range. (e.g. 192.168.10.30) Note: The Start IP and End IP specify the range of IP addresses to automatically assign to computers or devices on your network. Copyright 2013 TRENDnet. All Rights Reserved. 31 TRENDnet Users Guide TEW-731BR Domain Name (Optional) Specifies a domain name to assign to computers or devices. (e.g. trendnet.com) Lease Time Click the drop-down list to select the lease time. Note: The DHCP lease time is the amount of time a computer or device can keep an IP address assigned by the DHCP server. When the lease time expires, the computer or device will renew the IP address lease with the DHCP server, otherwise, if there is no attempt to renew the lease, the DHCP server will reallocate the IP address to be assigned to another computer or device. 4. To save changes, click Apply. Dynamic DHCP List You can view the list of active lease entries for computers or devices that have been assigned IP addresses automatically from the DHCP server on your router. Set up DHCP reservation Main > LAN & DHCP Server DHCP (Dynamic Host Configuration Protocol) reservation (also called Static DHCP) allows your router to assign a fixed IP address from the DHCP server IP address range to a specific device on your network. Assigning a fixed IP address can allow you to easily keep track of the IP addresses used on your network by your computers or devices for future reference or configuration such as virtual server (also called port forwarding, see Virtual Server on page 36) or special applications (also called port triggering, see Special Applications on page 37). 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Main, and click on LAN & DHCP Server. 3. Review the DHCP reservation settings. Static DHCP Enable or Disable the DHCP reservation feature. Name Enter a name for the reservation. IP Address Enter the IP address to assign to the reservation. (e.g. 192.168.10.101) Note: You cannot assign IP addresses outside of the DHCP range. The IP address is required to be within the DHCP IP address range (Start IP & End IP). MAC Address Enter the MAC (Media Access Control) address of the computer or network device to assign to the reservation. (e.g. 00:11:22:AA:BB:CC) Add - Saves the reservation. Copyright 2013 TRENDnet. All Rights Reserved. 32 TRENDnet Users Guide Static DHCP List You can view the list of reservations for computers or devices that have been created in this list. To modify an existing reservation, click on the entry in the Static DHCP list. When selected, the entry will be highlighted. Update Saves changes to an existing reservation. Delete Removes an existing reservation. Cancel Discards changes to existing reservation. Enable/disable UPnP on your router Management > Remote Management UPnP (Universal Plug and Play) allows devices connected to a network to discover each other and automatically open the connections or services for specific applications (e.g. instant messenger, online gaming applications, etc.) UPnP is enabled on your router by default to allow specific applications required by your computers or devices to allow connections through your router as they are needed. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Management, and click on Remote Management. 3. Next to UPnP, click Enabled or Disabled to turn the feature on or off on your router. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR Note: It is recommended to leave this setting enabled, otherwise, you may encounter issues with applications that utilize UPnP in order allow the required communication between your computers or devices and the Internet. 4. To save changes, click Apply. Allow/deny VPN connections through your router Management > Remote Management A Virtual Private Network (VPN) is a network that uses a public network, such as the Internet, to provide secure communications between a remote computer or network and another network. Some offices often provide VPN access to their networks to enable employees to work from their remote office/home office, or while traveling. If your office or place of work has allowed and authorized access for you to access their network through VPN, the default VPN settings in your router have been configured to pass through the most common types of VPN protocols, which typically do not require any additional configuration changes. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Management, and click on Remote Management. 3. Next to PPTP, L2TP, or IPsec (depending the VPN protocol your corporation requires) click Enabled or Disabled to turn the VPN pass through feature on or off on your router. Note: It is recommended to leave these settings enabled. 4. To save changes, click Apply. 33 TRENDnet Users Guide Allow/deny multicast streaming Management > Remote Management In some cases, applications require multicast communication (also called IP multicast which is the delivery of information to a specific group of computers or devices in a single transmission) typically used in media streaming applications. Multicast streaming is enabled by default on your router to allow applications that require multicast communication through your router which typically does not require additional configuration changes. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Management, and click on Remote Management. 3. Next to Multicast Stream, click Enabled or Disabled to turn the feature on or off on your router. Note: It is recommended to leave this setting enabled. 4. To save changes, click Apply. Identify your network on the Internet Main > Dynamic DNS Since most ISPs constantly change your home IP address, providing access to devices on your home or small office Local Area Network (such as IP Cameras) from the Internet requires setting up a Dynamic DNS service and entering the parameters into this management area. Dynamic DNS services allow your router to confirm its location to the given Dynamic DNS service, thereby providing the Dynamic DNS service with the ability to provide a virtual fixed IP address for your network. This means that even though your ISP is always changing your IP address, the Dynamic DNS service will be able to identify your network using a fixed addressone that can be used to view home IP Camera and other devices on your local area network. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR Note: First, you will need to sign up for one of the DDNS service providers listed in the Server Address drop-down list. 1. Sign up for one of the DDNS available service providers list under Server Address.
(e.g. dyndns.com, no-ip.com, etc.) 2. Log into your router management page (see Access your router management page on page 27). 3. Click on Main and click on Dynamic DNS. 4. Next to DDNS, click Enabled. 5. In the Server Address drop-down list, select the provider you selected, and enter your information in the fields. Host Name: Personal URL provided to you by your Dynamic DNS service provider (e.g. www.trendnet.dyndns.biz) User Name: The user name needed to log in to your Dynamic DNS service account Password: This is the password to gain access to Dynamic DNS service (NOT your router or wireless network password) for which you have signed up to. 6. To save changes, click Apply. 34 TRENDnet Users Guide Allow remote access to your router management page Management > Remote Management You may want to make changes to your router from a remote location such at your office or another location while away from your home. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Management, and click on Remote Management. 3. Under the HTTP section, click Enabled. Port It is recommended to leave this setting as 8080. Note: If you have configured port 8080 for another configuration section such as virtual server or special application, please change the port to use.
(Recommended port range 1024-65534) Remote IP Range It is recommended to leave this setting as *, to allow remote access from anywhere on the Internet. Note: You can enter a specific range of Internet IP addresses that are allowed to access your router management page, all others will be denied. 4. To save changes, click Apply. Open a device on your network to the Internet This router can provide access to devices on your local area network to the Internet using the Virtual Server, Special Application, method (DMZ NOT recommended). Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR DMZ Access > DMZ You may want to expose a specific computer or device on your network to the Internet to allow anyone to access it. Your router includes the DMZ (Demilitarized Zone) feature that makes all the ports and services available on the WAN/Internet side of the router and forwards them to a single IP address (computer or network device) on your network. The DMZ feature is an easy way of allowing access from the Internet however, it is a very insecure technology and will open local area network to greater threats from Internet attacks. It is strongly recommended to use Virtual Server (also called port forwarding, see Virtual Server on page 36) to allow access to your computers or network devices from the Internet. 1. Make the computer or network device (for which you are establishing a DMZ link) has a static IP address (or you can use the DHCP reservation feature to ensure the device has a fixed IP address) (see Set up DHCP reservation on page 32). A. Signing up for a Dynamic DNS service (outlined in the DDNS section) will provide identification of the routers network from the Internet. 2. Log into your router management page (see Access your router management page on page 27). 3. Click on Access, and click on DMZ. 4. Next to DMZ Enable, click Enabled. 5. Next to DMZ Host IP, enter the IP address you assigned to the computer or network device to expose to the Internet. 6. To save changes, click Apply. 35 TRENDnet Users Guide Virtual Server Access > Virtual Server Virtual Server (also called port forwarding) allows you to define specific ports (used or required by a specific application) and forward them to a single IP address (a computer or device) on your network. Using this feature is more secure compared to using DMZ
(see DMZ on page 35) in which DMZ forwards all ports instead of only specific ports used by an application. An example would be forwarding a port to an IP camera
(TRENDnet IP cameras default to HTTP TCP port 80 for remote access web requests) on your network to be able to view it over the Internet. Since most ISPs constantly change your home IP address, to be able to access the Virtual Server port(s) from the Internet it is recommended to setup Dynamic DNS service (See DynDNS section). 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Access, and click on Virtual Server. To simplify configuration, there is a list of commonly used pre-defined virtual server entries to modify, otherwise, you can choose to manually add a new virtual server. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR 3. Review the virtual server settings. Enabled Selecting Enabled turns on the virtual server and selecting Disabled turns off the virtual server. Name Enter a name for the virtual server. Protocol Select the protocol required for your device. TCP, UDP, or you can select Both to choose both TCP & UDP (recommended). Note: Please refer to the device documentation to determine which ports and protocols are required. Private Port Enter the port number required by your device. Refer to the connecting devices documentation for reference to the network port(s) required. Public Port Enter the port number used to access the device from the Internet. Note: The Public Port can be assigned a different port number than the Private Port
(also known as port redirection), however it is recommended to use the same port number for both settings. Please refer to the device documentation to determine which ports and protocols are required. LAN Server Enter the IP address of the device to forward the port (e.g. 192.168.10.101). Note: You should assign a static IP address to the device or use DHCP reservation to ensure the IP address of the device does not change. 36 TRENDnet Users Guide Add Saves a new virtual server entry. Delete Removes an existing virtual server. Update Modifies an existing virtual server. Cancel Discard changes to an existing virtual server. TEW-731BR Example: To forward TCP port 80 to your IP camera 1. Setup DynDNS service (See DynDNS section). 2. Access TRENDnet IP Camera management page and forward Port 80 (see product documentation) 3. Make sure to configure your network/IP camera to use a static IP address or you can use the DHCP reservation feature (see Set up DHCP reservation on page 32). Note: You may need to reference your camera documentation on configuring a static IP address. 4. Log into your router management page (see Access your router management page on page 27). 5. Click on Access, and click on Virtual Server. 6. In the list below, click the pre-defined virtual server entry named Virtual Server HTTP. Note: The selected item will be highlighted in yellow when selected. 7. The fields will be populated with the selected pre-defined virtual server entry. Copyright 2013 TRENDnet. All Rights Reserved. 8. Click Enabled to turn on this virtual server. 9. Next to Name, you can enter another name for the virtual server, otherwise, leave the default name. 10. Next to Protocol, make sure TCP is selected in the drop-down list. 11. The Private Port and Public Port, make sure port number 80 is configured for both settings. 12. Next to LAN Server, enter the IP address assigned to the camera. (e.g. 192.168.10.101) 13. To save the changes, click Update. 37 TRENDnet Users Guide Special Applications Access > Special AP Special applications (also called port triggering) is typically used for online gaming applications or communication applications that require a range of ports or several ports to be dynamically opened on request to a device on your network. The router will wait for a request on a specific port or range of ports (or trigger port/port range) from a device on your network and once a request is detected by your router, the router will forward a single port or multiple ports (or incoming port/port range) to the device on your network. This feature is not typically used as most devices and routers currently use UPnP (Universal Plug and Play) to automatically configure your router to allow access for applications. See Enable/disable UPnP on your router on page 33. Note: Please refer to the device documentation to determine if your device supports UPnP first, before configuring this feature. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Access, and click on Special AP. To simplify configuration, there is a list of commonly used pre-defined special application entries to modify, otherwise, you can choose to manually add a new special application. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR 3. Review the special application settings. Enabled Selecting Enabled turns on the special application and selecting Disabled turns it off. Name Enter a name for the special application. Trigger Port or port range requested by the device. o Protocol Select the protocol requested by the device. TCP, UDP, or you can select Both to choose both TCP and UDP. o Port Range Enter the ports or port range requested by the device.
(e.g. 554-554 or 6112-6112). Note: Please refer to the device documentation to determine which ports and protocols are required. Incoming Port(s) forwarded to the device. o Protocol Select the protocol to be forwarded to the device. TCP, UDP, or you can select Both to choose both TCP and UDP. o Port Range Enter the ports or port range to be forwarded to the device.
(e.g. 2000-2038,2069,2081,2200-2210). Note: Please refer to the device documentation to determine which ports and protocols are required. 38 TRENDnet Users Guide Add Saves a new special application. To modify an existing application, click on the entry in the special applications list. When selected, the entry will be highlighted. Delete Removes an existing special application. Update Modifies an existing special application. Cancel Discard changes to an existing special application. TEW-731BR Add static routes to your router Routing > Static You may want set up your router to route computers or devices on your network to other local networks through other routers. Generally, different networks can be determined by the IP addressing assigned to those networks. Generally speaking and for the case of an example, your network may have 192.168.10.x IP addressing and another network may have 192.168.20.x IP addressing and because the IP addressing of these two networks are different, they are separate networks. In order to communicate between the two separate networks, static routing needs to be configured. Below is an example diagram where routing is needed for devices and computers on your network to access the other network. Note: Configuring this feature assumes that you have some general networking knowledge. Copyright 2013 TRENDnet. All Rights Reserved. 39 TRENDnet Users Guide 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Routing, and click on Static. 3. Review the static route settings. Network Address Enter the IP network address of the destination network for the route.
(e.g. 192.168.20.0) route.
(e.g. 255.255.255.0) Network Mask Enter the subnet mask of the destination network for the Gateway Address Enter the gateway to the destination network for the route.
(e.g. 192.168.10.2) Interface Click the drop-down list and select the Interface on your router where the route is active.
(e.g. LAN) Metric Enter the metric or priority of the route. The metric range is 1-15, the lowest number 1 being the highest priority. (e.g. 1 ) TEW-731BR To modify an existing reservation, click on the entry in the static route list. When selected, the entry will be highlighted. Update Saves changes to an existing static route. Delete Removes an existing static route. Cancel Discards changes to existing static route. Add Saves the static route. Copyright 2013 TRENDnet. All Rights Reserved. 40 TRENDnet Users Guide Enable dynamic routing on your router Routing > Dynamic You may want to setup your router to route computers or devices on your network to other local networks through other routers. If other routers support dynamic routing such as RIP (Routing Information Protocol), you can enable this feature on your router to automatically learn the required routes to reach those networks. It is required that the same dynamic routing protocol and version is also enabled on the other routers in order your router and the other routers to exchange information about the network. Note: Configuring this feature assumes that you have some general networking knowledge. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Routing, and click on Dynamic. 3. Select the appropriate dynamic routing protocol and version communicate with other routers. TEW-731BR o RIP 1 - Receive routing information from other routers using the RIP o RIP 2 Receive routing information from other routers using the RIP version 1 protocol. version 2 protocol. 4. Click Apply to save the changes or click Cancel to discard the changes. Transmit Allows your router to send out network information to other routers so other routers can dynamically build routes to your network. other routers. o Disabled Disable sending routing information from your router to o RIP 1 - Sends out routing information to other routers using the RIP o RIP 2 Sends out routing information to other routers using the RIP version 1 protocol. version 2 protocol (recommended if supported by both devices). Receive - Allows your router to receive network information from other router so your router can build routes to other networks. o Disabled Disable receiving routing information from other routers to your router. Copyright 2013 TRENDnet. All Rights Reserved. 41 TRENDnet Users Guide Router Maintenance & Monitoring Reset your router to factory defaults Tools > Settings You may want to reset your router to factory defaults if you are encountering difficulties with your router and have attempted all other troubleshooting. Before you reset your router to defaults, if possible, you should backup your router configuration first, see Backup and restore your router configuration settings on page 43. There are two methods that can be used to reset your router to factory defaults. Reset Button Located on the rear panel of your router, see Product Hardware Features on page 2 . Use this method if you are encountering difficulties with accessing your router management page. OR Router Management Page 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Tools and click on Settings. 3. Under Restore factory default settings, click Restore. When prompted to confirm this action, click OK. Copyright 2013 TRENDnet. All Rights Reserved. Router Default Settings Administrator User Name Administrator Password Router IP Address Router Subnet Mask DHCP Server IP Range Wireless SSID (wireless network name) Wireless Security 802.11 Mode Channel TEW-731BR admin admin 192.168.10.1 255.255.255.0 192.168.10.101-192.168.199 Enabled TRENDnet731 Disabled 2.4GHz 802.11b/g/n mixed mode Auto Channel 42 TRENDnet Users Guide Backup and restore your router configuration settings Tools > Settings You may have added many customized settings to your router and in the case that you need to reset your router to default, all your customized settings would be lost and would require you to manually reconfigure all of your router settings instead of simply restoring from a backed up router configuration file. To backup your router configuration:
1. Log into your router management page (see Access your router management page on page 27). 2. Click on Tools and click on Settings. 3. Under Save Configuration Settings and next to Save Settings, click Save. 4. Depending on your web browser settings, you may be prompted to save a file (specify the location) or the file may be downloaded automatically to the web browser settings default download folder. (Default Filename: cfg.bin) To restore your router configuration:
1. Log into your router management page (see Access your router management page on page 27). 2. Click on Tools and click on Settings. Copyright 2013 TRENDnet. All Rights Reserved. 3. Under Restore Configuration Settings, next to Load Settings, depending on your web browser, click on Browse or Choose File. TEW-731BR A separate file navigation window should open. 4. Select the router configuration file to restore and click Load.
(Default Filename: cfg.bin). If prompted, click Yes or OK. 5. Wait for the router to restore settings. 43 TRENDnet Users Guide Upgrade your router firmware Tools > Firmware TRENDnet may periodically release firmware upgrades that may add features or fix problems associated with your TRENDnet router model and version. To check if there is a firmware upgrade available for your device, please check your TRENDnet model and version using the link. http://www.trendnet.com/downloads/
In addition, it is also important to verify if the latest firmware version is newer than the one your router is currently running. To identify the firmware that is currently loaded on your router, log in to the router, click on the Status tab and then on the Device Information sub-tab. The firmware used by the router is listed at the top of this page. If there is a newer version available, also review the release notes to check if there were any new features you may want or if any problems were fixed that you may have been experiencing. 1. If a firmware upgrade is available, download the firmware to your computer. 2. Unzip the file to a folder on your computer. Please note the following:
Do not interrupt the firmware upgrade process. Do not turn off the device or press the Reset button during the upgrade. If you are upgrade the firmware using a laptop computer, ensure that the laptop is connected to a power source or ensure that the battery is fully charged. Disable sleep mode on your computer as this may interrupt the firmware upgrade process. Do not upgrade the firmware using a wireless connection, only using a wired network connection. Any interruptions during the firmware upgrade process may permanently damage your router. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Status and click on Device Information to check your routers current firmware version at the top of the page. 3. Click on Tools and click on Firmware. 4. Depending on your web browser, next to Upgrade Firmware, click Browse or Choose File. 5. Navigate to the folder on your computer where the unzipped firmware file (.bin) is located and select it. 6. Click Upgrade. If prompted, click yes or OK. 44 TRENDnet Users Guide Restart your router Tools > Restart You may want to restart your router if you are encountering difficulties with your router and have attempted all other troubleshooting. There are two methods that can be used to restart your router. Turn the router off for 10 seconds using the router On/Off switch located on the rear panel of your router, see Product Hardware Features on page 2 . Use this method if you are encountering difficulties with accessing your router management page. This is also known as a hard reboot or power cycle. OR Router Management Page This is also known as a soft reboot or restart. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Tools and click on Restart. If prompted, click yes or OK. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR Check connectivity using the router management page Tools > Ping Test For troubleshooting purposes, you may want to check your router connectivity using the ping (also known as a network connectivity test) test tool on your router management page. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Tools and click on Ping Test. 3. Enter in the IP address (e.g. 192.168.10.101) or host name (e.g. www.trendnet.com) to test. 4. Click Ping. 5. You will receive a success or fail result message of the address you entered providing a basic indicating of the routers connectivity to the Internet or devices that are connected to your network. Click Back to bring you back to the Ping Test page. 45 TRENDnet Users Guide Check the router system information Status > Device Information You may want to check the system information of your router such as WAN (Internet) connectivity, wireless and wired network settings, router MAC address, and firmware version. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Status and click on Device Information. 3. Review the device information. TEW-731BR IP Address The current IP address assigned to your router WAN port or interface configuration. Subnet Mask - The current subnet mask assigned to your router WAN port or interface configuration. Default Gateway The current gateway assigned to your router WAN port or interface configuration. DNS (Domain Name System) The current DNS address(es) assigned to your router port or interface configuration. Firmware Version The current firmware version your router is running. Router Up Time The duration your router has been running continuously without a restart/power cycle (hard or soft reboot) or reset. WAN (Internet) Information MAC Address The current MAC address used by your routers WAN port or interface configuration. Connection Displays the current WAN (Internet) connection status. When using DHCP Client (or Dynamic IP address) Internet connection type, you will provide the option to Release and Renew your IP address settings. Other Internet connection types such as PPPoE will provide the option to Connect and Disconnect. Wireless Information MAC Address The current MAC address of your routers wireless or interface configuration. Connection Displays the status if your wireless functionality on your router is enabled or disabled. SSID Displays the current wireless network name assigned to your router. Channel Displays the current wireless channel your router is operating. Authentication Displays the current wireless security configured on your router. Copyright 2013 TRENDnet. All Rights Reserved. 46 TRENDnet Users Guide Wired LAN Information MAC Address The current MAC address of your routers wired LAN or interface configuration. IP Address - Displays your routers current IP address. Subnet Mask Displays your routers current subnet mask. DHCP Server - Display your routers DHCP server status, enabled or disabled, and provides a link to the DHCP client listing. View your router log Status > Log Your router log can be used to obtain activity information on the functionality of your router or for troubleshooting purposes. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Status and click on Log. 3. Review the device log information. Time Displays the time of the log entry. If the time is inaccurate, make sure to set the router date and time correctly. (See Set your router date and time on page 28) Type Displays a notification regarding the type of log. Message Displays the log message. Router Log Navigation First Page Displays the first page of the log. Last Page Displays the last page of the log. Previous Page Display the log page previous to the current. The Page: 1/1 will display the current page. Next Page Displays the log page next to the current. Refresh - The Page: 1/1 will display the current page. Clear Log - Clears all logging 47 TRENDnet Users Guide Configure your router log Status > Log Setting You may want send your router log to your e-mail address or to an external log server
(also known as Sysco server) so you can check it periodically while away from home. You may also want to only see specific categories of logging. Send router logs to your e-mail address 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Status and click on Log Setting. 3. Review the e-mail log settings. SMTP Authentication Set this option to Enabled if your e-mail service requires authentication. If not, leave this setting to Disabled. Note: If you are unsure of this setting check with your e-mail service provider if authentication is required. SMTP Account Enter your account user name for your e-mail service. SMTP Password Enter your password for your e-mail service. SMTP Server Enter the IP address (e.g. 10.10.10.10) or domain name (e.g. mail.trendnet.com) of your e-mail server. SMTP Server Port Enter the port used by your e-mail service. (e.g. Default SMTP Server Port: 25) From Email Address Enter a sender e-mail address. (e.g. router@trendnet.com) Note: This does not need to be real e-mail address, only used for identification purposes when checking your e-mail. To Email Address Enter your e-mail address. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR Email Log Now Click this option to send an e-mail with the current router log using your email settings. Email Logs Select when you want the router log to be e-mailed. o When log is full The router log will be e-mailed to your e-mail address when router internal log is full. o Click the drop-down list and configure to e-mail logs according to a set schedule. Once on a specific day of the week or once every day. 4. To save changes, click Apply. Send router logs to an external log server 1. Log into your router management page (see Access your router management page on page 27). 48 TRENDnet Users Guide 2. Click on Status and click on Log Setting. 3. Next to Syslog Server, enter the IP address of the external log server to send router logging. 4. To save changes, click Apply. Set the types or categories to include in logging 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Status and click on Log Setting. 3. Next to Log Type, check the types or categories to include in logging. 4. To save changes, click Apply. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR View your router packet statistics Status > Statistics You may want to check your router packet statistics for informational purposes only. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Status and click on Statistic. 3. The table displays the amount of packets sent and received on your routers wired LAN, wireless, and WAN (Internet). View wireless devices connected to your router Status > Wireless You may want to check the wireless devices connected to your router. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Status and click on Wireless. 3. The table displays the amount time each wireless device has been connected and the MAC address of each wireless device. 49 TRENDnet Users Guide Capture packets using the router management page Management > Capture Packets You may want to use the router management page to capture data packets for further troubleshooting and analysis. Packet captures allow you to see what type of data and information is inside each packet. You will need a packet capture software application to be able to open and view the packet capture files downloaded from the router. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Management and click on Capture Packets. 3. Click on the Network Interface drop-down list and select which interface you would like to capture data packets, LAN or WAN. 4. Review the options for capturing packets. Start Starts the packet capture. Stop - Stops the packet capture Download Download the packet capture file.
(.pcap file) TEW-731BR Enable SNMP on your router Management > SNMP SNMP (Simple Network Management Protocol) is a network management protocol used to monitor (read) and/or manage (write) multiple network devices on a network. This preconfigured external SNMP server. 1. Log into your router management page (see Access your router management page on page 27). 2. Click on Management and click on SNMP. 3. Review the options for SNMP. SNMP Select Enabled to enable SNMP. System Location Enter the location. (optional) System Contact Enter the contact. (optional) Community Enter the community to match the settings with the external SNMP server. Trap Receiver 1-3 Enter the IP address of the external SNMP trap receiver. You can enter up to three receivers. (e.g. 192.168.10.250) 4. To save changes, click Apply. Copyright 2013 TRENDnet. All Rights Reserved. 50 TRENDnet Users Guide Router Management Page Structure Main LAN & DHCP Server o WAN Static DHCP Reservation o Clone MAC Address Password Time Dynamic DNS IPv6 Wireless Basic Advanced Wi-Fi Protected Setup Security Status Device Information Log Log Setting o Email Log o o Log Type Syslog Statistic Wireless Copyright 2013 TRENDnet. All Rights Reserved. Routing Static Dynamic Routing Table Access Filter o MAC Filters o Domain/URL Blocking o Protocol/IP Filters Special AP Virtual Server DMZ Firewall Rule Management SNMP Remote Management Capture Packets Routing Static Dynamic Routing Table TEW-731BR Tools Restart Settings o o Restore Configuration Settings o Reset to Factory Default Save Configuration Settings Firmware Upgrade Firmware Ping Test Wizard Setup Wizard 51 TEW-731BR TRENDnet Users Guide Technical Specifications Hardware Standards WAN LAN WPS Button Power Switch Connection Type Supported Web Browsers Internet Access Control Management/
Monitoring Routing LED Indicators Power Power Consumption Dimension (L x W x H) Weight Temperature IEEE 802.3 (10BASE-T), IEEE 802.3u (100BASE-TX), IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3az 1 x 10/100 Mbps Auto-MDIX port (internet) 4 x 10/100 Mbps Auto-MDIX ports Enables Wi-Fi Protected Setup (WPS) function (Hold for 3 seconds) On / Off power switch Dynamic IP, Static (fixed) IP, PPPoE, PPTP, L2TP, IPv6 6rd
(IPv6 rapid deployment) DHCPv4, manual and automatic configuration Internet Explorer 6.0 or above, Firefox 2.0 or above, Chrome, Opera, Safari MAC Address Filter, Domain / URL Filter, Protocol / IP Filter, Virtual Server, DMZ host, UPnP, PPTP / L2TP / IPsec VPN pass through Local / remote configuration, upgrade firmware, backup /
restore configuration via Web browser, Internal System Log, Syslog, E-Mail Logging, SNMPv1/v2c, Ping Test Tool, Dynamic DNS Static and Dynamic RIPv1/2 Power, Status, LAN1~LAN4, WAN, WLAN Input: 100~240V AC, 50~60Hz Output: 5V DC, 1A 3.0 watts (max) 158 x 109 x 34 mm (6.2 x 4.3 x 1.3 in) 210 g (7.4oz) Operation: 0~ 40C (32F~ 104F); Storage: -10~ 70C Copyright 2013 TRENDnet. All Rights Reserved. Humidity Certifications Wireless Frequency Antenna Modulation Media Access Protocol Data Rate Security Output Power Receiving Sensitivity
(14F~158 F) Max 90% (non-condensing) CE, FCC 2.412~2.484 GHz band 2 x 2 dBi fixed dipole antennas 802.11b: CCK (11 and 5.5 Mbps), DQPSK (2 Mbps), DBPSK
(1 Mbps) 802.11g: OFDM with BPSK, QPSK and 16/64-QAM 802.11n: BPSK, QPSK, 16QAM, 64QAM with OFDM CSMA/CA with ACK 802.11b: Up to 11 Mbps 802.11g: Up to 54 Mbps 802.11n: Up to 300 Mbps 64/128-bit WEP (HEX/ASCII), WPA / WPA2-RADIUS, WPA /
WPA2-PSK 802.11b: 15 dBm (typical) @ 11 Mbps 802.11g: 15 dBm (typical) @ 54 M bps 802.11n: 13 dBm (typical) @ 300Mbps 802.11b: -85 dBm (typical) @ 11 Mbps 802.11g: -68 dBm (typical) @ 54 Mbps 802.11n: -62 dBm (typical) @ 300 Mbps 1~ 11 (FCC), 1~13 (ETSI) Channels
*Maximum wireless signal rates are referenced from IEEE 802.11 theoretical specifications. Actual data throughput and coverage will vary depending on interference, network traffic, building materials and other conditions. 52 TRENDnet Users Guide Troubleshooting Q: I typed http://192.168.10.1 in my Internet Browser Address Bar, but an error message says The page cannot be displayed. How can I access the router management page?
Answer:
1. Check your hardware settings again. See Router Installation on page 2. 2. Make sure the LAN and WLAN lights are lit. 3. Make sure your network adapter TCP/IP settings are set to Obtain an IP address automatically or DHCP (see the steps below). 4. Make sure your computer is connected to one of the routers LAN ports 5. Press on the factory reset button for 15 seconds, the release. Windows 7 a. Go into the Control Panel, click Network and Sharing Center. b. Click Change Adapter Settings, right-click the Local Area Connection icon. c. Then click Properties and click Internet Protocol Version 4 (TCP/IPv4). d. Then click Obtain an IP address automatically and click OK. Windows Vista a. Go into the Control Panel, click Network and Internet. b. Click Manage Network Connections, right-click the Local Area Connection icon and click Properties. c. Click Internet Protocol Version (TCP/IPv4) and then click Properties. d. Then click Obtain an IP address automatically and click OK. Windows XP/2000 a. Go into the Control Panel, double-click the Network Connections icon b. Right-click the Local Area Connection icon and the click Properties. c. Click Internet Protocol (TCP/IP) and click Properties. d. Then click Obtain an IP address automatically and click OK. Note: If you are experiencing difficulties, please contact your computer or operating system manufacturer for assistance. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR Q: I am not sure what type of Internet Account Type I have for my Cable/DSL connection. How do I find out?
Answer:
Contact your Internet Service Provider (ISP) for the correct information. Q: The Wizard does not appear when I access the router. What should I do?
Answer:
1. Click on Wizard on the left hand side. 2. Near the top of the browser, Pop-up blocked message may appear. Right click on the message and select Always Allow Pop-ups from This Site. 3. Disable your browser's pop up blocker. Q: I went through the Wizard, but I cannot get onto the Internet. What should I do?
Answer:
1. Verify that you can get onto the Internet with a direct connection into your modem
(meaning, plug your computer directly to the modem and verify that your single computer (without the help of the router) can access the Internet). 2. Power cycle your modem and router. Unplug the power to the modem and router. Wait 30 seconds, and then reconnect the power to the modem. Wait for the modem to fully boot up, and then reconnect the power to the router. 3. Contact your ISP and verify all the information that you have in regards to your Internet connection settings is correct. Q: I cannot connect wirelessly to the router. What should I do?
Answer:
1. Double check that the WLAN light on the router is lit. 2. Power cycle the router. Unplug the power to the router. Wait 15 seconds, then plug the power back in to the router. 3. Contact the manufacturer of your wireless network adapter and make sure the wireless network adapter is configured with the proper SSID. The preset SSID is TRENDnet(model_number). 4. To verify whether or not wireless is enabled, login to the router management page, click on Wireless. 5. Please see Steps to improve wireless connectivity on page 19 if you continue to have wireless connectivity problems. 53 TRENDnet Users Guide Appendix How to find your IP address?
Note: Please note that although the following procedures provided to follow for your operating system on configuring your network settings can be used as general guidelines, however, it is strongly recommended that you consult your computer or operating system manufacturer directly for assistance on the proper procedure for configuring network settings. Command Prompt Method Windows 2000/XP/Vista/7/8 1. On your keyboard, press Windows Logo+R keys simultaneously to bring up the Run dialog box. 2. In the dialog box, type cmd to bring up the command prompt. 3. In the command prompt, type ipconfig /alto display your IP address settings. MAC OS X 1. Navigate to your Applications folder and open Utilities. 2. Double-click on Terminal to launch the command prompt. 3. In the command prompt, type ipconfiggetifaddr<en0 or en1>to display the wired or wireless IP address settings. Note: en0 is typically the wired Network and en1 is typically the wireless Airport interface. Graphical Method MAC OS 10.6/10.5 1. From the Apple menu, select System Preferences. 2. In System Preferences, from the View menu, select Network. 3. In the Network preference window, click a network port (e.g., Network, AirPort, modem). If you are connected, you'll see your IP address settings under "Status:"
MAC OS 10.4 1. From the Apple menu, select Location, and then Network Preferences. 2. In the Network Preference window, next to "Show:", select Network Status. You'll see your network status and your IP address settings displayed. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR Note: If you are experiencing difficulties, please contact your computer or operating system manufacturer for assistance. How to configure your network settings to obtain an IP address automatically or use DHCP?
Note: Please note that although the following procedures provided to follow for your operating system on configuring your network settings can be used as general guidelines, however, it is strongly recommended that you consult your computer or operating system manufacturer directly for assistance on the proper procedure for configuring network settings. Windows 7/8 a. Go into the Control Panel, click Network and Sharing Center. b. Click Change Adapter Settings, right-click the Local Area Connection icon. c. Then click Properties and click Internet Protocol Version 4 (TCP/IPv4). d. Then click Obtain an IP address automatically and click OK. Windows Vista a. Go into the Control Panel, click Network and Internet. b. Click Manage Network Connections, right-click the Local Area Connection icon and click Properties. c. Click Internet Protocol Version (TCP/IPv4) and then click Properties. d. Then click Obtain an IP address automatically and click OK. Windows XP/2000 a. Go into the Control Panel, double-click the Network Connections icon b. Right-click the Local Area Connection icon and the click Properties. c. Click Internet Protocol (TCP/IP) and click Properties. d. Then click Obtain an IP address automatically and click OK. MAC OS 10.4/10.5/10.6 a. From the Apple, drop-down list, select System Preferences. b. Click the Network icon. c. From the Location drop-down list, select Automatic. d. Select and view your Network connection. In MAC OS 10.4, from the Show drop-down list, select Built-in Network and select the TCP/IP tab. In MAC OS 10.5/10.6, in the left column, select Network. e. Configure TCP/IP to use DHCP. 54 TRENDnet Users Guide TEW-731BR In MAC 10.4, from the Configure IPv4, drop-down list, select Using DHCP and click the Apply Now button. In MAC 10.5, from the Configure drop-down list, select Using DHCP and click the Apply button. In MAC 10.6, from the Configure drop-down list, select Using DHCP and click the Apply button. f. Restart your computer. Note: If you are experiencing difficulties, please contact your computer or operating system manufacturer for assistance. How to find your MAC address?
In Windows 2000/XP/Vista/7, Your computer MAC addresses are also displayed in this window, however, you can type getmac v to display the MAC addresses only. In MAC OS 10.4, 1. Apple Menu > System Preferences > Network 2. From the Show menu, select Built-in Network. 3. On the Network tab, the Network ID is your MAC Address. In MAC OS 10.5/10.6, 1. Apple Menu > System Preferences > Network 2. Select Network from the list on the left. 3. Click the Advanced button. 3. On the Network tab, the Network ID is your MAC Address.
) in the notification or How to connect to a wireless network using the built-in Windows utility?
Note: Please note that although the following procedures provided to follow for your operating system on configuring your network settings can be used as general guidelines, however, it is strongly recommended that you consult your computer or operating system manufacturer directly for assistance on the proper procedure for connecting to a wireless network using the built-in utility. Windows 7/8 1. Open Connect to a Network by clicking the network icon (
area. 2. In the list of available wireless networks, click the wireless network you would like to connect to, then click Connect. 4. You may be prompted to enter a security key in order to connect to the network. 5. Enter in the security key corresponding to the wireless network, and click OK. Windows Vista 1. Open Connect to a Network by clicking the Start Button. 2. In the Show list, click Wireless. 3. In the list of available wireless networks, click the wireless network you would like to connect to, then click Connect. 4. You may be prompted to enter a security key in order to connect to the network. 5. Enter in the security key corresponding to the wireless network, and click OK. Windows XP 1. Right-click the network icon in the notification area, then click View Available Wireless Networks. 2. In Connect to a Network, under Available Networks, click the wireless network you would like to connect to. 3. You may be prompted to enter a security key in order to connect to the network. 4. Enter in the security key corresponding to the wireless network, and click Connect. and then click Connect To. Copyright 2013 TRENDnet. All Rights Reserved. 55 TRENDnet Users Guide Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. RoHS This product is RoHS compliant. Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR Europe EU Declaration of Conformity This product is herewith confirmed to comply with the Directive of 1999/5/EC, 2006/95/EC, and 2009/125/EC. EC No. 278/2009 EN60950-1: 2006 + A11 : 2009 + A1 : 2010 Safety of Information Technology Equipment EN 50385: 2002 Product standard to demonstrate the compliance of radio base stations and fixed terminal stations for wireless telecommunication systems with the basic restrictions or the reference levels related to human exposure to radio frequency electromagnetic fields (110MHz - 40 GHz) - General public EN 300 328 V1.7.1 (2006-10) Class B Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN 301 489-1 V1.8.1 (2008-04) Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements EN 301 489-17 V2.1.1 (2009-05) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. 56 TRENDnet Users Guide esky [Czech]
Dansk [Danish]
Deutsch
[German]
Eesti [Estonian]
English Espaol
[Spanish]
[Greek]
Franais
[French]
TRENDnet tmto prohlauje, e tento TEW-731BR je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES, 2006/95/ES, a 2009/125/ES. Undertegnede TRENDnet erklrer herved, at flgende udstyr TEW-
731BR overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF, 2006/95/EF, og 2009/125/EF. Hiermit erklrt TRENDnet, dass sich das Gert TEW-731BR in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG, 2006/95/EG und 2009/125/EG befindet. Kesolevaga kinnitab TRENDnet seadme TEW-731BR vastavust direktiivi 1999/5/E, 2006/95/E ja 2009/125/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. Hereby, TRENDnet, declares that this TEW-731BR is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC, 2006/95/EC, and 2009/125/EC. Por medio de la presente TRENDnet declara que el TEW-731BR cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE, 2006/95/CE, 2009/125/CE y. TRENDnet TEW-
731BR 1999/5/, 2006/95/, 2009/125/ . Par la prsente TRENDnet dclare que l'appareil TEW-731BR est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE, 2006/95/CE, 2009/125/CE et. Italiano[Italian]
Con la presente TRENDnet dichiara che questo TEW-731BR conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE, 2006/95/CE e 2009/125/CE. Latviski [Latvian] AroTRENDnetdeklar, ka TEW-731BR atbilstDirektvas 1999/5/EK, 2006/95/EK, un 2009/125/EK btiskajmprasbm un citiemar to saisttajiemnoteikumiem. Lietuvi
[Lithuanian]
iuo TRENDnet deklaruoja, kad is TEW-731BR atitinka esminius reikalavimus ir kitas 1999/5/EB, 2006/95/EB ir 2009/125/EB Copyright 2013 TRENDnet. All Rights Reserved. TEW-731BR Direktyvos nuostatas. Nederlands
[Dutch]
Hierbij verklaart TRENDnet dat het toestel TEW-731BR in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG, 2006/95/EG, en 2009/125/EG. Malti [Maltese]
Hawnhekk, TRENDnet, jiddikjara li dan TEW-731BR jikkonforma mal-
tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-
Dirrettiva 1999/5/KE, 2006/95/KE, u 2009/125/KE. Magyar
[Hungarian]
Polski [Polish]
Portugus
[Portuguese]
Slovensko
[Slovenian]
Slovensky
[Slovak]
Alulrott, TRENDnet nyilatkozom, hogy a TEW-731BRmegfelel a vonatkoz alapvet kvetelmnyeknek s az 1999/5/EK irnyelv, a 2006/95/EK s a 2009/125/EK irnyelv egyb elrsainak. Niniejszym TRENDnet owiadcza, e TEW-731BR jest zgodny z zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/WE, 2006/95/WE i 2009/125/WE. TRENDnet declara que este TEW-731BR est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE, 2006/95/CE e 2009/125/CE. TRENDnet izjavlja, da je ta TEW-731BR v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive 1999/5/ES, 2006/95/ES in 2009/125/ES. TRENDnettmtovyhlasuje, e TEW-731BRspazkladnpoiadavky a vetkyprslunustanoveniaSmernice 1999/5/ES, 2006/95/ES, a 2009/125/ES. Suomi [Finnish]
TRENDnet vakuuttaa tten ett TEW-731BR tyyppinen laite on direktiivin 1999/5/EY, 2006/95/EY ja 2009/125/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Svenska
[Swedish]
Hrmed intygar TRENDnet att denna TEW-731BR str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG, 2006/95/EG och 2009/125/EG. 57 TRENDnet Users Guide Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TEW-731BR 3 Years Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty. If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defective product or part and deliver an equivalent product or part to the customer. The repair/replacement units warranty continues from the original date of purchase. All products that are replaced become the property of TRENDnet. Replacement products may be new or reconditioned. TRENDnet does not issue refunds or credit. Please contact the point-of-purchase for their return policies. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. There are no user serviceable parts inside the product. Do not remove or attempt to service the product by any unauthorized service center. This warranty is voided if (i) the product has been modified or repaired by any unauthorized service center, (ii) the product was subject to accident, abuse, or improper use (iii) the product was subject to conditions more severe than those specified in the manual. Warranty service may be obtained by contacting TRENDnet within the applicable warranty period and providing a copy of the dated proof of the purchase. Upon proper submission of required documentation a Return Material Authorization (RMA) number will be issued. An RMA number is required in order to initiate warranty service support for all TRENDnet products. Products that are sent to TRENDnet for RMA service must have the RMA number marked on the outside of return packages and sent to TRENDnet prepaid, insured and packaged appropriately for safe shipment. Customers shipping from outside of the USA and Canada are responsible for return shipping fees. Customers shipping from outside of the USA are responsible for custom charges, including but not limited to, duty, tax, and other fees. WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMERS SOLE REMEDY SHALL BE, AT TRENDNETS OPTION, REPAIR OR REPLACE. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING Copyright 2013 TRENDnet. All Rights Reserved. Limited Warranty WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF TRENDNETS PRODUCTS. TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMERS OR ANY THIRD PERSONS MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD. LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT TRENDNETS OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. Governing Law: This Limited Warranty shall be governed by the laws of the state of California. Some TRENDnet products include software code written by third party developers. These codes are subject to the GNU General Public License ("GPL") or GNU Lesser General Public License ("LGPL"). Go to http://www.trendnet.com/gpl or http://www.trendnet.com Download section and look for the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these codes. Please go to http://www.gnu.org/licenses/gpl.txt or http://www.gnu.org/licenses/lgpl.txt for specific terms of each license. PWP05202009v2 2013/01/07 58
This product uses the FCC Data API but is not endorsed or certified by the FCC