all | frequencies |
|
|
exhibits | applications |
---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
User Manual (Statements) | Users Manual | 12.79 KiB | ||||
1 2 |
|
User Manual | Users Manual | 4.35 MiB | ||||
1 2 | Attestation Statements | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | External Photos | |||||||
1 2 | Internal Photos | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | Operational Description | |||||||
1 2 | RF Exposure Info | |||||||
1 2 | Test Report | |||||||
1 2 | Test Report | |||||||
1 2 | Test Setup Photos |
1 2 | User Manual (Statements) | Users Manual | 12.79 KiB |
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Note: The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. 2006/8/16 v1.0
1 2 | User Manual | Users Manual | 4.35 MiB |
a TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Table of Contents Product Overview 1 Package Contents 1 Features 1 Front Panel 2 Mounting Holes 2 Connectors 2 Product Pre-set Information 3 Mounting Accessories 3 Hardware Installation 4 Mount on Wall or Ceiling 4 Mount on T-Bar 4 Wireless Performance Considerations 5 Operation Modes 5 Access Point 5 WDS Bridge 5 WDS AP 5 Universal Repeater5 Application Diagram 6 System configuration 7 System Management and Default Settings 7 Table of Contents Log-in System Management for the First Time 7 Setup Wizard 9 Status 10 System 13 Wireless 16 Management 24 Federal Communication Commission Interference Statement 32 Europe EU Declaration of Conformity 33 RoHS 33 Limited Warranty 35 b TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Product Overview TEW-753DAP Package Contents TEW-753DAP package includes:
TEW-753DAP Multi-Language Quick Installation Guide CD-ROM ( Users Guide) Network cable (1.5 m/5 ft.) Power adapter (12 V, 1.25 A) If any package contents are missing or damaged, please contact the retail store, online retailer, or reseller/distributor from which the product was purchased. Product Overview Features TRENDnets N600 Dual Band PoE Access Point, model TEW-753DAP, is a feature rich business class access point with proven concurrent 300 Mbps dual band wireless technology. A variety of installation scenarios are supported with Access Point, WDS AP, WDS Bridge, and Repeater modes. Save installation time and costs with PoE. Quick Setup Get up and running in minutes with the intuitive guided setup Low Profile Off white low profile smoke detector shape blends into most environments Power over Ethernet (PoE) Save installation time and costs with a PoE (Optional power port for non-PoE installations) LED Control Disable diagnostic LEDs to further reduce visual attention Concurrent Dual Band Proven concurrent 300 Mbps dual band wireless n Gigabit Port Gigabit port maintains high performance connection to network Wireless Coverage Increased coverage with MIMO technology Backward Compatible Compatible older wireless g devices 1 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Operation Modes Independently set each band to Access Point, WDS AP, WDS Bridge, or Repeater mode IPv6 IPv6 support AP Scan Integrated wireless scan function helps optimize wireless setup SSIDs Up to 8 SSIDs per band (16 total) with isolation support Traffic Shaping Allocate bandwidth to each wireless SSID System Logs Eight system logs aid network troubleshooting Spanning Tree Configurable spanning tree controls SNMP Extend network monitoring to this device with SNMP support Encrypted Wireless Support for encryption up to WPA2 VLAN Management Up to eight SSIDs per band with VLAN management support Network Access Create MAC filter tables to reduce network access risk Product Overview Concurrent dual band 300 Mbps* wireless N Create up to 8 SSIDs per band No need to install the device near a power source with PoE installation Manage traffic shaping per SSID Off-white low profile housing blends into environment Off-white housing blends into environment 3-year limited warranty IPv6 support
*Maximum wireless signal rates are referenced from IEEE 802.11 theoretical specifications. Actual data throughput and coverage will vary depending on interference, network traffic, building materials and other conditions. 2 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Front Panel Reset Button Mounting Holes Wireless Network Power Push and hold for 2 seconds to reset TEW-753DAP Push and hold for more than 10 seconds to reset configuration to factory default Connectors Gigabit PoE Port OFF ON OFF Powered off or LED display has been disabled Powered on No network connected through Ethernet port
(PoE) or LED display has been disabled Network connected through Ethernet port (PoE) ON Flashing Network activities are detected on Ethernet OFF
(PoE) port No wireless network connection or LED display has been disabled Flashing Wireless network activities are detected Reset Button Power LED Network LED Orange: 10/100 Green: Giga bit Wireless LED Orange: 2.4GHz Green: 5GHz Product Overview Mounting holes Kensington security slot DC Power 12V DC 1.25A
(Optional) 3 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Product Preset Information Mounting Accessories There are two preset product labels comes with the package. The first label is located on plastic wrapping of TEW-753DAP. The second label is located on the bottom of the TEW-753DAP. You can find default SSID, wireless key, administrator account, and administrator password there. The default static management IP is 192.168.10.100. The mounting accessories are provided for easier hardware installation, including two sets of T-Bar clippers, two sets of screws, and a set of spacers. Product Overview TRENDnet753_2.4GHz_XXXX 0123456#
http://tew-753dap 15/16 T-Bar Clips 9/16 T-Bar Clips P26 * 10 Screws P26 * 25 Screws Made in Taiwan Spacers 4 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Hardware Installation Mount on Wall or Ceiling Use two P3.5 pan head screws to hold the TEW-753DAP. The distance between mounting points is 2 3/4 (7cm) Installation Mount on T-Bar Two additional bronze screw holes are provided for T-Bar mounting. Use two P2.6 screws to secure the TEW-753DAP on T-Bar clip and then clip on the T-Bar. 5 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Wireless Performance Considerations There are a number of factors that can impact the range of wireless devices. Adjust your wireless devices so that the signal is traveling in a straight path, rather than at an angle. The more material the signal has to pass through the more signal you will lose. Keep the number of obstructions to a minimum. Each obstruction can reduce the range of a wireless device. Position the wireless devices in a manner that will minimize the amount of obstructions between them. Building materials can have a large impact on your wireless signal. In an indoor environment, try to position the wireless devices so that the signal passes through less dense material such as dry wall. Dense materials like metal, solid wood, glass or even furniture may block or degrade the signal. Antenna orientation can also have a large impact on your wireless signal. Use the wireless adapters site survey tool to determine the best antenna orientation for your wireless devices. Interference from devices that produce RF (radio frequency) noise can also impact your signal. Position your wireless devices away from anything that generates RF noise, such as microwaves, radios and baby monitors. Any device operating on the 2.4GHz frequency will cause interference. Devices such as 2.4GHz cordless phones or other wireless remotes operating on the 2.4GHz frequency can potentially drop the wireless signal. Although the phone may not be in use, the base can still transmit wireless signal. Move the phones base station as far away as possible from your wireless devices. Adjust the wireless power setting on your AP if you have more than one AP covering a large area. Covering only the neighbor hop APs in wireless range is a good design. Covering more than neighbor APs will experience wireless interference and slow down the communication. Installation Operation Modes There are four operating modes provided by TEW-753DAP, Access Point, Client Bridge, WDS and Repeater. Configure the TEW-753DAP to different operation mode which service the best in your network. Access Point This is the default operation mode. TEW-753DAP service wireless end points in this mode. You can setup local or remote wireless authentication, setup up to 8 sets of SSIDs in 2.4GHz band and 5GHz band, total 16 SSIDs and separate SSID or STA traffic. Client Bridge When Client Bridge mode is set to 2.4GHz or 5GHz interface of TEW753DAP, this interface functions as a wireless client connecting to any AP dynamically
(channels and encryptions). The interface bridges the traffic to the Ethernet and the other wireless interface. Wireless Distribution System In Wireless Distributin System, WDS, mode you can configure the selected interface to be WDS bridge, WDS Access Point, or WDS Station. WDS Bridge: In this mode, the selected interface wirelessly communicate to other WDS bridges to make a wireless backbone. A WDS link is bidirectional;
both end points must support WDS and each access point must know the MAC Address of the other. Each access point will be configured with the remote access points MAC address and vice versa. Make sure all access points are configured with the same SSID, wireless channel and wireless encryption settings. WDS Access Point: This is a hybrid mode. The selected interface can be a WDS bridge and an access point at the same time. WDS Station: This is a hybrid mode. The selected interface can be a WDS bridge and a wireless station at the same time. 6 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Repeater When Repeater Mode is selected, the selected wireless interface functions as a wireless repeater and is able to repeat the wireless signal of an access point. This feature is used to expand your existing wireless network on places your current access point is unable to reach. Make sure all the settings on selected interface of the TEW-753DAP matches the wireless access points you want to repeat in same wireless settings including SSID, channel and wireless encryption settings. Installation 7 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Application Diagram Installation 8 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. System configuration System Management and Default Settings If you have a brand new out of box TEW-753DAP or if you just reset TEW-753DAP to factory defaults by pressing and holding reset button for over 10 seconds, your TEW-753DAP has following settings:
Management IP : 192.168.10.100 Administrator name : admin Administrator password : admin Default SSID :
Default SSID passphrase :
(printed on pre-set label)
(printed on pre-set label) Log-in System Management for the First Time 1 Power on your TEW-753DAP by connecting PoE cable to a PoE switch or plug-in the power adapter comes with the package. The power LED will turned on. System Configuration 2 Search for available wireless connections in your computers network settings. The default SSID of the TEW-735AP is shown on the preset label. The default wireless security settings are set to WPA2 and the passphrase is printed on the preset label and device label. Or, Connect a network cable from your computer to the TEW-753DAP network port. 9 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. 3 Open a web browser and type http://tew-753DAP to access web administration page. 4 Change your administration login password away from factory default setting. Click Next to continue. System Configuration If you have a static IP set on your PC, please open a web browser and enter http://192.168.10.100 The TEW-735AP login page will appear. 5 Change the management IP address for the TEW-753DAP if necessary. Click Apply Enter administrator login information (The default user name is admin and password is admin)
* Please reference the troubleshooting section if you cannot access administration web page. 10 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. 6 Click Save/ Reload on top of the menu and then click Save & Apply System Configuration 7 TEW-753DAP will apply password change and then reboot. Login again with your new password.
* Make sure you are still connecting to TEW-753DAP after reboot if you wireless connects to TEW-753DAP. 11 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Setup Wizard Setup wizard is provided as part of the web configuration utility. It sets up the basic administrator password and management IP address by clicking on the Wizard button on the function menu. The following screen will appear. 2 Enter the management IP address for this TEW-753DAP. The default IP address is 192.168.10.100. Set it up in your network management subnet with a unique IP address. You can leave it set on default IP if you have only one TEW-753DAP on network. Click Apply System Configuration 1 Enter your new administrator password and then click Next to continue. 12 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. 3 Click Save/ Reload on top of the menu and then click Save & Apply Save/ Reload System Configuration 4 TEW-753DAP will apply password change and then reboot. Login again with your new password.
* Make sure you are still connecting to TEW-753DAP after reboot if you wireless connects to TEW-753DAP. The TEW-753DAP is a commercial grade wireless access point. To make multiple network settings change at the same time and minimum the interruption of production network, all network configurations have to be changed in two stages. When you change a network setting, the change command will be saved in a queue. When you finish all the setting changes, click Save/
Reload on top of the menu. Review the list of command on your change list. Click Save & Apply to commit the change. If you want to trash the changes, click Revert The number following Save/ Reload is a reminder showing how many changes in the queue waiting to be commit. 13 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Status Main status page shows TEW-753DAP basic information. Click Status then main to show the page. System Configuration System Information Device Name : Name of this device recognized by other network device such as SNMP. Ethernet MAC Address : The MAC address of Ethernet Interface 2.4G Wireless MAC Address : The MAC address of each individual active SSID 5G Wireless MAC Address : The MAC address of each individual active SSID Country : The counting you are currently located. Current Time : The current time. This time is important for schedule control and log accuracy. Firmware version : Currently run firmware version Management VLAN ID : The VLAN ID assigned to device management network. The default setting is no VLAN tagging on management network traffic. 14 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. System Configuration LAN Settings IP Address :
IP address of TEW-753DAP Subnet Mask : Network range of IP address Default Gateway : Default route going further from TEW-
753DAP network Primary DNS : Primary DNS server address Secondary DNS : Secondary DNS server address DHCP Client : The TEW-753DAP IP address was set statically or dynamically. The IP address was statically set by default. Spanning Tree Protocol : Spanning Tree Protocol is enabled or not. IPv6 IP Address : The dual-stack IPv6 address of TEW753DAP. IPv6 Link-Local Address IPv6 link local address for auto-
configuration IPv6 Default Gateway IPv6 default route going further from TEW-753DAP network IPv6 Primary DNS Primary IPv6 DNS server address IPv6 Secondary DNS Secondary IPv6 DNS server address RX (packets) Received packets by Ethernet interface TX (packets) Transmitted packets from Ethernet interface 15 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. System Configuration Current Wireless Settings: 2.4GHz Operation Mode : Shows which wireless mode the 2.4GHz interface was set and running now. Wireless Mode : Shows which 802.11 wireless mode was set and running on the 2.4GHz interface. Channel Bandwidth : Wireless Channel Bandwidth
( 20 or 40 MHz) Frequency/ Channel : Shows which 2.4GHz wireless channel
(and frequency) was selected. Profile Settings : Briefly shows wireless settings (SSID/
Security/ VID/ 802.1Q) on each SSID. Distance : The distance setting of 2.4GHz wireless. RX (packets) Received packets by 2.4GHz wireless interface TX (packets) Transmitted packets from 2.4GHz wireless interface Current Wireless Settings: 5GHz Operation Mode : Shows which wireless mode the 5GHz interface was set and running now. Wireless Mode : Shows which 802.11 wireless mode was set and running on the 5GHz interface. Channel Bandwidth : Wireless Channel Bandwidth
( 20 or 40 MHz) Frequency/ Channel : Shows which 5GHz wireless channel (and frequency) was selected. Profile Settings : Briefly shows wireless settings (SSID/
Security/ VID/ 802.1Q) on each SSID. Distance : The distance setting of 5GHz wireless. 16 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. RX (packets) Received packets by 5GHz wireless interface TX (packets) Transmitted packets from 5GHz wireless interface Refresh : Click this button to refresh the list System Configuration 2.4G Wireless Client List This page shows all wireless clients connected to the 2.4GHz interface. SSID : # Wireless client was associated with which SSID and what is its client number MAC Address : MAC address of wireless client TX (Bytes) : Transmitting data statistics RX (Bytes) : Receiving data statistics RSSI(dBm) : Received Signal Strength Indication:
Signal strength of this wireless client Kick and Ban : Click this button to send this client to MAC address filter list. Click OK when you see this prompt. Refresh : Click this button to refresh the list 17 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. 5G Wireless Client List This page shows all wireless clients connected to the 2.4GHz interface. System Log This page allows users to view a running log of the access point system statistics, events and activities. System Configuration SSID : # Wireless client was associated with which SSID and what is its client number MAC Address : MAC address of wireless client TX (Bytes) : Transmitting data statistics RX (Bytes) : Receiving data statistics RSSI(dBm) : Received Signal Strength Indication: Signal strength of this wireless client Kick and Ban : Click this button to send this client to MAC address filter list. Click OK when you see this prompt. (Save & Reload to make your change in action) Refresh : Click this button to refresh the list Choose one of the filter to quickly find the log you want. Refresh : Click this button to refresh the log Clear : Click this button to clear up the log 18 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. System Operation Mode You can choose one of the mode to fit your network plan: Access Point, WDS AP, WDS Bridge and Universal Repeater. Access Point This is the default operation mode. Wireless clients, known as wireless stations (STAs), can wireless associate with TEW-753DAP and connect to Internet via Ethernet port. WDS AP In this operation mode. TEW-753DAP wireless connects to other WDS (Wireless Distribution System) for backbone System Configuration communication and provides wireless connection to clients (STAs) at the same time. WDS Bridge In this operation mode. TEW-753DAP connects ONLY to other WDS (Wireless Distribution System) as a backbone bridge. Universal Repeater TEW-753DAP repeats wireless signal and packets in this mode for backbone communication as well as client access. This feature is used to expand your existing wireless network on places your current access point is unable to reach. Make sure all the settings of the TEW-
753DAP matches to your root or connecting wireless access points, same SSID, channel and wireless encryption settings. IP Settings The TEW-753DAP has a static IP 192.168.10.100 set in factory for management purpose. You can change this IP address to fit your network plan. You can also set TEW-753DAP to DHCP client accepting IP dynamically. 19 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. System Configuration IP Address : Specify an IP address IP Subnet Mask : Specify a subnet mask for the IP address Default Gateway : Default route for TEW-753DAP Primary DNS : Primary DNS server address Secondary DNS : Secondary DNS server address Use Link Local Address : Check this to use link local address IPv6 IP Address : Specify an IPv6 dual-stack address Specify a subnet range for the IPv6 address IPv6 Subnet Prefix Length :
IPv6 Default Gateway : Default route for IPv6 IPv6 Primary DNS : Primary IPv6 DNS server address IPv6 Secondary DNS : Secondary IPv6 DNS server address Spanning Tree The TEW-753DAP is designed for end point access as well as backbone connection. To avoid network looping, you can enable 802.1d spanning tree protocol. 20 IP Network Setting : Select Obtain an IP address automatically (DHCP) or Specify an IP address. If you select specify an IP address, you have to enter following information manually. If SHCP is selected, then the IP address is received automatically from the external DHCP server. TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Spanning Tree Status: Enable or disable 802.1d spanning tree protocol to avoid network looping Bridge Hello Time : The time between each bridge protocol data unit (BPDU). Default: 2 sec. Bridge Max Age : Maximum time a BPDU kept in bridge. Default: 20 sec. Bridge Forward Delay : The time spend in listen and learning state. Default: 4 sec. Priority : Priority number for root bridge selection.
(MAC number is listed on Status > Main page) Apply : Click this button to save and activate Cancel : Click this button to abandon the change Band Steer The TEW-753DAP equipped with 2.4GHz and 5GHz wireless interfaces. When your client device can work on both 2.4GHz and 5GHz wireless, Band Steer can redirect your 2.4GHz crowded traffic to 5GHz band automatically. To setup band steer, you have to setup the same SSID on both 2.4GHz and 5GHz. Then check enable band steering on this page. Click Save System Configuration Save : Click this button to save the change.
(Save & Reload is required to take effect.) Cancel : Click this button to abandon the change 21 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. 24G Wireless Wireless Network General setups for your 2.4GHz wireless connection. You can setup up to eight SSIDs for different groups of users. System Configuration Network Mode : Choose between N only, G only, B only, B/G mixed, or B/G/N mixed mode. The rule of the thumb is choose single mode if your devices all works in the same mode. Mixed mode increases compatibility, but sometimes lowers the data speed. Channel HT Mode : The latest 802.11 protocol can combine channel for better wireless performance. You can choose fixed 20MHz or 40MHz, or automatically select 20MHz or 40MHz channels. Extension Channel : When you choose manual channel Channel / Frequency :
selection and 20/40MHz or 40MHz in channel HT mode, you can choose which neighbor channel you want to combine, upper channel or lower channel. If you want to setup fixed channel, choose a channel number to switch your radio frequency. Otherwise, check auto to select channel automatically which is set by default. US: Channel 1 - 11 Euro: Channel 1 - 13 Current Profile SSID (1 - 8) : The wireless network name setup for this SSID 22 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. System Configuration Security : Wireless security was setup to this SSID. VID : VLAN id for this SSID Enable : Check this box to enable this SSID Edit : Click Edit to change the settings of this SSID
(Save & Reload is required to take effect.) AP Detection Before you setup your TEW-753DAP wireless settings, you may want to know what signal is current running in the air. Click Scan to make a site survey and list available access points around you. Type : The 802.11 wireless mode this access point provides. Security : Which wireless security was set to use. Mode: This wireless source works on infrastructure mode or ad hoc mode. Go Back : Click this button to go back SSID Settings Click Edit one the SSID you want to edit. The following setup window will appear. BSSID : Basic SSID. This is strictly unique SSID to identify a wireless access point, WAP. It is also the MAC address of the wireless interface. SSID : Service Set Identifier. This SSID is human readable and performs as ESSID to setup wireless groups. Channel : 2.4GHz wireless channel number Signal Level : The signal strength from the access point. Specify the SSID for the current profile. Check this option to hide the SSID from clients. If 2.4G/5G SSID Profile SSID Suppressed SSID checked, the SSID will not appear in the site survey. Station Separation communication between client devices. Wireless Security Save / Cancel Click the appropriate radio button to allow or prevent See the Wireless Security section. Click Save to accept the changes or Cancel to cancel 23 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. and return previous settings. ESSID Selection : Select the SSID you want to set up wireless security Separate : SSID: If you check this box, clients associated with this SSID cannot communicate with wireless clients associated with other SSID directly. STA: If you check this box, wireless clients (a.k.a. STA) associated with this SSID cannot communicate to each other directly. Even they are in the same wireless group. Broadcast ESSID : Select Enable or Disable from the drop-
down list. This is the SSID broadcast feature. When this option is set to Enable, your wireless network name is broadcast to anyone within wireless signal range. When this is disabled, you must enter the Wireless Network Name (SSID) on the client manually to connect to the network. WMM : Choose to Enable or Disable WMM. This is the Quality of Service (QoS) feature for prioritizing voice and video applications. Encryption : Choose between disable, WEP, WPA, WPA2 or 802.1x for your wireless security. System Configuration Encryption (Disabled) : Choosing disable allow wireless clients connects to TEW-753DAP without password You can relay the authentication to remote RADIUS server by checking Enable 802.1x Authentication and entering RADIUS server information. 24 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Encryption (WEP) : WEP, Wire Equivalent Protection, provides a basic wireless security Enable 802.1x Authentication :
Authentication Type : Select Open System, Shared Key, or auto. Open System allows any client to authenticate as long as it conforms to any MAC address filter policies that may have been set. All authentication packets are transmitted without encryption. Shared Key sends an unencrypted challenge text string to any device attempting to communicate with the AP. The device requesting authentication encrypts the challenge text and sends it back to the access point. If the challenge text is encrypted correctly, the access point allows the requesting device to authenticate. It is recommended to select Auto if you are not sure which authentication type is used. Key Length : Select a 64-bit or 128-bit WEP key length from the drop-down list Key Type : Select a key type from the drop-down list. 128-bit encryption requires a longer key than 64-bit encryption. Keys are defined by entering in a string in HEX
(hexadecimal - using characters 0-9, A-F) or ASCII (American Standard Code for Information Interchange - alphanumeric characters) format. ASCII format is provided so you can enter a string that is easier to remember Default Key : You may choose one of your 4 different WEP keys from below Encryption Key 1-4 : You may enter four different WEP keys System Configuration Check on this box if you would like to use static WEP plus 802.1x authentication. This option works with a RADIUS Server to authenticate wireless clients. Wireless clients can either use Static WEP or 802.1x authentication in order to connect to the network. For 802.1x, clients should have necessary credentials to be authenticated by the Server. Furthermore, it is necessary to specify the RADIUS Servers IP address, service port number, and shared secret. Encryption
(WPA pre-shared key) :
Wi-Fi Protected Access (WPA) pre-shared key WPA Type : Select TKIP, AES, or WPA2 Mixed. The encryption algorithm used to secure the data communication. TKIP (Temporal Key Integrity Protocol) provides per-packet key generation and is based on WEP. AES
(Advanced Encryption Standard) is a very secure block based encryption. Note that, if the bridge uses the AES option, the bridge can associate with the access point only if the access point is also set to use only AES. Pre-shared Key Type : The Key Type can be passphrase or Hex format 25 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Pre-shared Key : The key is entered as a pass-phrase of up to 63 alphanumeric characters in ASCII
(American Standard Code for Information Interchange) format at both ends of the wireless connection. It cannot be shorter than eight characters, although for proper security it needs to be of ample length and should not be a commonly known phrase. This phrase is used to generate session keys that are unique for each wireless client System Configuration WPA Type : Select TKIP, AES, or WPA2 Mixed. The encryption algorithm used to secure the data communication. TKIP (Temporal Key Integrity Protocol) provides per-packet key generation and is based on WEP. AES
(Advanced Encryption Standard) is a very secure block based encryption. Note that, if the bridge uses the AES option, the bridge can associate with the access point only if the access point is also set to use only AES. IP address of RADIUS server RADIUS Server IP Address :
RADIUS Server Port : RADIUS service port number. Default:
RADIUS Server Shared Secret:
1812 RADIUS service shared secret to authenticate this credential agent. Encryption
(WPA RADIUS) :
Use RADIUS server manage your wireless authentication keys for easier account management Apply : Click this button to apply the change Cancel : Click this button to abandon the change Wireless MAC Filter Set up wireless security settings in this page. Select SSID you want to set up, change the value and then click on Apply to commit the changes. Enabling security prevents any unauthorized wireless clients to connect into your network. 26 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Wireless Advanced Settings Fine tuning your wireless settings on this page. System Configuration Fragment Threshold : Packets over the specified size will be fragmented in order to improve performance on noisy networks. Specify a value between 256 and 2346. The default value is 2346. RTS Threshold : Packets over the specified size will use the RTS/CTS mechanism to maintain performance in noisy networks and preventing hidden nodes from degrading the performance. Specify a value between 0 and 2347. The default value is 2347 Beacon Interval : Beacons are packets sent by a wireless Access Point to synchronize wireless devices. Specify a Beacon Interval value between 24 and 1024. The default value is set to 100 milliseconds. DTIM Period : A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages. When the wireless Access Point has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Period value. Wireless clients detect the beacons and awaken to receive the broadcast and multicast messages. The default value is 1. Valid settings are between 1 and 10. Data rate : You can select a data rate from the drop-
down list, however, it is recommended to select auto. In auto mode, TEW753DAP will choose the maximum data rate to fit the instant wireless channel quality automatically. 27 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. N Data Rate : Select different 802.11N Modulation and Coding Scheme (MCS) against particular wireless noise. Or, select auto letting TEW-753DAP select MCSs dynamically. Channel Bandwidth : Select channel bandwidth for 1) Dynamic select 20 MHz and 40MHz bandwidth or 2) choose 20MHz channels only Preamble Type : Select a short or long preamble. For optimum performance it is recommended to also configure the client device to the same preamble type. CTS Protection : Clear to Send, CTS, can be always enabled, auto, or disabled. By enabled CTS, the Access Point and clients will wait for a channel cleared signal before transmitting. It is recommended setting to auto Tx Power : Wireless signal transmission power. Set transmission power to appropriate value can make your multiple AP deployment easier. The default value is 26 dBm. Valid settings are between 11 and 29. Apply : Click this button to apply the change Cancel : Click this button to abandon the change Apply : Click this button to apply the change Cancel : Click this button to abandon the change WPS System Configuration WPS is the simplest way to connect a wireless client to TEW-753DAP. You dont have to select the encryption mode and fill in a long encryption passphrase every time when you try to setup a wireless connection. You only need to press a button on both wireless client and TEW-753DAP, and the WPS will do the rest for you. The TEW-753DAP supports two types of WPS: WPS via Push Button and WPS via PIN code. If you want to use the Push Button, you have to push a specific button on the wireless client or in the utility of the wireless client to start the WPS pairing, and click the Start to Process button in this page under WPS via Push Button to start WPS pairing. If you want to use the PIN code, you have to know the PIN code of the wireless client and switch it to WPS mode, then fill-in the PIN code of the wireless client through the web configuration interface of the wireless router. 28 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. System Configuration WPS Via Push Button :
Click on the Start to Process button if you would like to enable WPS through the Push Button instead of the PIN. After pressing this button you will be required to press the WPS on the client device within two minutes. Click on the OK button in the dialog box WPS via PIN : Specify a PIN, which unique number that can be used to add the router to an existing network or to create a new network. Then click on the Start to Process button WPS : Check this box to enable feature WPS Current Status : Displays the current status of the WPS configuration Self Pin Code : Displays PIN code of TEW-753DAP SSID : Displays the SSID for WPS pairing. Only the first SSID (SSID_1) can proceed WPS pairing. Displays the authentication mode of SSID_1 Authentication Mode :
Passphrase Key : Current passphrase 29 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. 5G Wireless Wireless Network General setups for your wireless connection. You can setup up to four SSIDs for different group of users. System Configuration Radio : Enable or disable overall wireless signals Mode : The operation mode setting in System section Band : Choose the Wi-Fi connection protocols you want to run on AP Enabled SSID# : Choose the number of SSIDs you want to enable (Range: 1 ~ 4) ESSID1 - 4 : SSID names for enabled groups Auto Channel : Enable or disable auto channel selection Channel :
(for Fixed Channel) specify channel number Check Channel Time :
(for Auto Channel) specify how frequently TEW-753DAP is checking the channel status Apply : Click this button to apply the change Cancel : Click this button to abandon the change 30 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. System Configuration ESSID Selection : Select the SSID you want to set up wireless security Separate : SSID: If you check this box, clients associated with this SSID cannot communicate with wireless clients associated with other SSID directly. STA: If you check this box, wireless clients (a.k.a. STA) associated with this SSID cannot communicate to each other directly. Even they are in the same wireless group. Broadcast ESSID : Select Enable or Disable from the drop-
down list. This is the SSID broadcast feature. When this option is set to Enable, your wireless network name is broadcast to anyone within wireless signal range. When this is disabled, you must enter the Wireless Network Name (SSID) on the client manually to connect to the network. 31 Wireless MAC Filter Set up wireless security settings in this page. Select SSID you want to set up, change the value and then click on Apply to commit the changes. Enabling security prevents any unauthorized wireless clients to connect into your network. TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. WMM : Choose to Enable or Disable WMM. This is the Quality of Service (QoS) feature for prioritizing voice and video applications. Encryption : Choose between disable, WEP, WPA, WPA2 or 802.1x for your wireless security. Encryption (Disabled) : Choosing disable allow wireless clients connects to TEW-753DAP without password You can relay the authentication to remote RADIUS server by checking Enable 802.1x Authentication and entering RADIUS server information. System Configuration Encryption (WEP) : WEP, Wire Equivalent Protection, provides a basic wireless security 32 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Authentication Type : Select Open System, Shared Key, or auto. Open System allows any client to authenticate as long as it conforms to any MAC address filter policies that may have been set. All authentication packets are transmitted without encryption. Shared Key sends an unencrypted challenge text string to any device attempting to communicate with the AP. The device requesting authentication encrypts the challenge text and sends it back to the access point. If the challenge text is encrypted correctly, the access point allows the requesting device to authenticate. It is recommended to select Auto if you are not sure which authentication type is used. Key Length : Select a 64-bit or 128-bit WEP key length from the drop-down list Key Type : Select a key type from the drop-down list. 128-bit encryption requires a longer key than 64-bit encryption. Keys are defined by entering in a string in HEX
(hexadecimal - using characters 0-9, A-F) or ASCII (American Standard Code for Information Interchange - alphanumeric characters) format. ASCII format is provided so you can enter a string that is easier to remember Default Key : You may choose one of your 4 different WEP keys from below Encryption Key 1-4 : You may enter four different WEP keys Enable 802.1x Authentication :
System Configuration Check on this box if you would like to use static WEP plus 802.1x authentication. This option works with a RADIUS Server to authenticate wireless clients. Wireless clients can either use Static WEP or 802.1x authentication in order to connect to the network. For 802.1x, clients should have necessary credentials to be authenticated by the Server. Furthermore, it is necessary to specify the RADIUS Servers IP address, service port number, and shared secret. Encryption
(WPA pre-shared key) :
Wi-Fi Protected Access (WPA) pre-shared key WPA Type : Select TKIP, AES, or WPA2 Mixed. The encryption algorithm used to secure the data communication. TKIP (Temporal Key Integrity Protocol) provides per-packet key generation and is based on WEP. AES
(Advanced Encryption Standard) is a very secure block based encryption. Note that, if the bridge uses the AES option, the bridge can associate with the access point only if the access point is also set to use only AES. Pre-shared Key Type : The Key Type can be passphrase or Hex format 33 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Pre-shared Key : The key is entered as a pass-phrase of up to 63 alphanumeric characters in ASCII
(American Standard Code for Information Interchange) format at both ends of the wireless connection. It cannot be shorter than eight characters, although for proper security it needs to be of ample length and should not be a commonly known phrase. This phrase is used to generate session keys that are unique for each wireless client System Configuration WPA Type : Select TKIP, AES, or WPA2 Mixed. The encryption algorithm used to secure the data communication. TKIP (Temporal Key Integrity Protocol) provides per-packet key generation and is based on WEP. AES
(Advanced Encryption Standard) is a very secure block based encryption. Note that, if the bridge uses the AES option, the bridge can associate with the access point only if the access point is also set to use only AES. IP address of RADIUS server RADIUS Server IP Address :
RADIUS Server Port : RADIUS service port number. Default:
RADIUS Server Shared Secret:
1812 RADIUS service shared secret to authenticate this credential agent. Encryption
(WPA RADIUS) :
Use RADIUS server manage your wireless authentication keys for easier account management Apply : Click this button to apply the change Cancel : Click this button to abandon the change Wireless Advanced Settings Fine tuning your wireless settings on this page. 34 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. System Configuration Beacon Interval : Beacons are packets sent by a wireless Access Point to synchronize wireless devices. Specify a Beacon Interval value between 24 and 1024. The default value is set to 100 milliseconds. DTIM Period : A DTIM is a countdown informing clients of the next window for listening to broadcast and multicast messages. When the wireless Access Point has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Period value. Wireless clients detect the beacons and awaken to receive the broadcast and multicast messages. The default value is 1. Valid settings are between 1 and 10. Data rate : You can select a data rate from the drop-
down list, however, it is recommended to select auto. In auto mode, TEW753DAP will choose the maximum data rate to fit the instant wireless channel quality automatically. N Data Rate : Select different 802.11N Modulation and Coding Scheme (MCS) against particular wireless noise. Or, select auto letting TEW-753DAP select MCSs dynamically. Channel Bandwidth : Select channel bandwidth for 1) Dynamic select 20 MHz and 40MHz bandwidth or 2) choose 20MHz channels only Preamble Type : Select a short or long preamble. For optimum performance it is recommended to also configure the client device to the same preamble type. 35 Fragment Threshold : Packets over the specified size will be fragmented in order to improve performance on noisy networks. Specify a value between 256 and 2346. The default value is 2346. RTS Threshold : Packets over the specified size will use the RTS/CTS mechanism to maintain performance in noisy networks and preventing hidden nodes from degrading the performance. Specify a value between 0 and 2347. The default value is 2347 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. CTS Protection : Clear to Send, CTS, can be always enabled, auto, or disabled. By enabled CTS, the Access Point and clients will wait for a channel cleared signal before transmitting. It is recommended setting to auto Tx Power : Wireless signal transmission power. Set transmission power to appropriate value can make your multiple AP deployment easier. The default value is 26 dBm. Valid settings are between 11 and 29. Apply : Click this button to apply the change Cancel : Click this button to abandon the change WPS WPS is the simplest way to connect a wireless client to TEW-753DAP. You dont have to select the encryption mode and fill in a long encryption passphrase every time when you try to setup a wireless connection. You only need to press a button on both wireless client and TEW-753DAP, and the WPS will do the rest for you. The TEW-753DAP supports two types of WPS: WPS via Push Button and WPS via PIN code. If you want to use the Push Button, you have to push a specific button on the wireless client or in the utility of the wireless client to start the WPS pairing, and click the Start to Process button in this page under WPS via Push Button to start WPS pairing. If you want to use the PIN code, you have to know the PIN code of the wireless client and switch it to WPS mode, then fill-in the PIN code of the wireless client through the web configuration interface of the wireless router. System Configuration WPS : Check this box to enable feature WPS Current Status : Displays the current status of the WPS configuration Self Pin Code : Displays PIN code of TEW-753DAP SSID : Displays the SSID for WPS pairing. Only the first SSID (SSID_1) can proceed WPS pairing. Displays the authentication mode of SSID_1 Authentication Mode :
Passphrase Key : Current passphrase 36 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. WPS Via Push Button :
Click on the Start to Process button if you would like to enable WPS through the Push Button instead of the PIN. After pressing this button you will be required to press the WPS on the client device within two minutes. Click on the OK button in the dialog box WPS via PIN : Specify a PIN, which unique number that can be used to add the router to an existing network or to create a new network. Then click on the Start to Process button System Configuration 37 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Management Administration Change the password required to log into the access points web-based management. Passwords can contain 0 to 12 alphanumeric characters, and are case sensitive. Enter your password and system information and then click Apply to save the change. System Configuration System Name: The system name can be identified on your local network. Changing this system name can change the way you access this AP. For example, if you change the system name to lobbyfront, you can access this AP by typing http://lobbyfront/ in Windows and log on to the management page. Default system name is tew-753DAP. Idle Timeout Automatically Default 10 minutes. Old Password: Type in the current password to allow changing to a new password. New Password: Enter your new password here. Confirm Password:
Type your new password again for verification purposes 38 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Management VLAN This feature is only available under Access Point or WDS AP mode and allows users to configure the 802.1q VLAN settings to for all wireless clients. Enter VLAN ID you want to tag to clients associated with specific SSID. Different SSID should set to different VLAN ID. Enable Virtual LAN service and click Apply to save the changes. LAN VLAN MGMT is a special VLAN to manage TEW-753DAP. Enabling management VLAN tagging will keep all services, for example DHCP server and client, in this VLAN. This page allows you to assign a VLAN tag to the packets. A VLAN is a group of computers on a network whose software has been configured so that they behave as if they were on a separate Local Area Network
(LAN). Computers on VLAN do not have to be physically located next to one another on the LAN. Note: Only applicable in Access Point and WDS AP mode System Configuration 39 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Virtual LAN : Choose to Enable or Disable the VLAN features SSID 1 - 4 Tag : Enter VLAN tag you want to add for associated clients. Check the leading check box to enable tagging. All SSIDs have to have different VLAN tag. Valid settings are between 1 and 4094. LAN VLAN MGMT : Enable or disable TEW-753DAP services on a specific VLAN. If management VLAN tagging is enabled. All service packets, including web management, DHCP server/
client, will be tagged with specified tag. MGMT Tag : VLAN number for TEW-753DAP services. This number has to be different to all above VLAN numbers. Apply : Click this button to apply the change Cancel : Click this button to abandon the change Wireless Traffic Shaping Traffic shaping regulates the flow of packets leaving an interface to deliver improved Quality of Service. System Configuration 40 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. SNMP Active : Choose to enable or disable the SNMP feature SNMP Version : Select SNMP version from the drop-down list SNMP Manager IP : Specify the SNMP manager IP address Read Community Name : Specify the password for access the SNMP community for read only access System Configuration Set Community Name : Specify the password for access to the SNMP community with read/write access System Location : Specify the location of the TEW-753DAP System Contact : Specify the contact details of the TEW-
753DAP Trap Active : Choose to enable or disable the SNMP trapping feature Trap Manager IP : Specify the password for the SNMP trap community Trap Community : Specify the name of SNMP trap community Apply : Click this button to apply the change Cancel : Click this button to abandon the change SNMP Settings SNMP Setting allows you to assign the contact details, location, community name and trap settings for SNMP. This is a networking management protocol used to monitor network-attached devices. SNMP allows messages (called protocol data units) to be sent to various parts of a network. Upon receiving these messages, SNMP-compatible devices (called agents) return data stored in their Management Information Bases. SNMP Active : Choose to enable or disable the SNMP feature SNMP Version : Select SNMP version from the drop-down list SNMP Manager IP : Specify the SNMP manager IP address Read Community Name : Specify the password for access the SNMP community for read only access 41 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Set Community Name : Specify the password for access to the SNMP community with read/write access System Location : Specify the location of the TEW-753DAP System Contact : Specify the contact details of the TEW-
753DAP Trap Active : Choose to enable or disable the SNMP trapping feature Trap Manager IP : Specify the password for the SNMP trap community Trap Community : Specify the name of SNMP trap community Apply : Click this button to apply the change Cancel : Click this button to abandon the change Backup / Restore Settings This page allows you to save the current configurations. Click Save to save your current configuration. To load configurations saved previously, click Browse ... to find configuration file and then click Upload In case you want to reset TEW-753DAP configuration back to factory default, click Reset in this page. All configurations will be set back to its original default settings. System Configuration Auto Reboot Settings Click on Apply, the TEW-753DAP will going through all the reboot process automatically. 42 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. System Configuration 1 If a firmware upgrade is available, download the firmware to your computer. 2 Unzip the file to a folder on your computer. 3 Log into the TEW-753DAP 4 Click on Management and then Firmware Upgrade 5 Click Browse... and navigate to the folder on your computer in which the unzipped firmware file (.bin) is. 6 Located and select it the firmware file. 7 Click Apply Time Setting The Time Setting allows your access point to reference or base its time on the settings configured here, which will affect functions such as log entries and schedules. Firmware Upgrade TRENDnet may periodically release firmware upgrades that might add features or fix problems associated with your TRENDnet model and version. To find out if there is a firmware upgrade available for your device, please check your TRENDnet model and version using the link. http://www.trendnet.com/downloads/
43 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Time Setup : Choose a source of time to synchronize with. You can choose to synchronize the TEW-753DAP with a NTP server or your PC Time Zone : Select the time zone of the country you are currently in. The TEW-753DAP will set its time based on your selection. NTP Time Server : Specify a time server (NTP server) to synchronize with. (e.g. pool.ntp.org) Daylight Savings : Check this box if your time zone has daylight savings. DST Start / DST End : Specify the starting date and end date of daylight savings. Apply : Click this button to apply the change Cancel : Click this button to abandon the change Schedule Service schedule can be set up daily or weekly for power saving and security reason. Click Add to add a schedule rule entry. Select an entry and click Edit or Delete Selected to change the entry. Click Delete All to remove all entries. After schedule editing, click Apply to save your schedule. Check Enabled Schedule Table to make AP services work with schedule. System Configuration Add : Add scheduled service Edit : Edit selected scheduled service Delete Selected : Delete selected scheduled service Delete All : Click this button to clear up the list Apply : Click this button to apply the change Cancel : Click this button to abandon the change 44 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. CLI Settings To check your network connection, you can use the PING tool from your TEW-753DAP. Enter the IPv4 address you want to ping and click Start The result will be showed in the terminal down below. System Configuration Log To check your network connection, you can use the PING tool from your TEW-753DAP. Enter the IPv4 address you want to ping and click Start The result will be showed in the terminal down below. Diagnosis To check your network connection, you can use the PING tool from your TEW-753DAP. Enter the IPv4 address you want to ping and click Start The result will be showed in the terminal down below. 45 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. System Configuration Device Name : Device name of neighbor TEW-753DAP. Operation Mode : Which operation mode the neighbor TEW-
IP Address :
753DAP is running. IP address of neighbor TEW-753DAP System MAC Address : System MAC address (LAN/ 2.4GHz wireless interface MAC address) of neighbor TEW-753DAP. Device Discovery The TEW-753DAP can discover other TEW-753DAP on neighbor wired or wireless network. Firmware Version : Specify the starting date and end date of daylight savings. Refresh : Click this button to discover the new neighbor devices. LED Control All LED indicators are turned on by default. You can turn any one of them or all of them on or off. Click the LED you want to change the action and then click Save/Apply to save and apply the changes. 46 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Power LED Network LED Orange: 10/100 Green: Giga bit Wireless LED Orange: 2.4GHz Green: 5GHz OFF ON OFF Powered off or LED display has been disabled Powered on No network connected through Ethernet port
(PoE) or LED display has been disabled Network connected through Ethernet port (PoE) ON Flashing Network activities are detected on Ethernet OFF
(PoE) port No wireless network connection or LED display has been disabled Flashing Wireless network activities are detected Logout Logout from the management page. The TEW-753DAP allows only one management login at the same time. If you want to access the TEW-753DAP from different computer, remember to logout the web management page first. System Configuration 47 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that Increase the separation between the equipment and receiver. to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Interference Statement IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user 48 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Europe EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC, 2006/95/EC and 2009/125/EC.. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC, 2006/95/EC and 2009/125/
EC:
EN 60950-1:2006+A11:2009+A1:2010+A12:2011 IEC 60950-1:2005 (2nd Edition) Am 1:2009 Safety of Information Technology Equipment EN50385 : 2002 Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (0 Hz - 300 GHz) EN 300 328 V1.7.1 Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN 301 489-1 V1.9.2 Electromagnetic compatibility and Radio Spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements EN 301 489-17 V2.2.1 Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. Declaration of Conformity In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. RoHS This product is RoHS compliant. 49 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. cs esky
[Czech]
da Dansk
[Danish]
de Deutsch
[German]
et Eesti
[Estonian]
en English es Espaol
[Spanish]
el
[Greek]
fr Franais
[French]
it Italiano
[Italian]
lv Latviski
[Latvian]
lt Lietuvi
[Lithuanian]
TRENDnet tmto prohlauje, e tento TEW-753DAP je ve shod se zkladnmi poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES, 2006/95/ES, a 2009/125/ES. Undertegnede TRENDnet erklrer herved, at flgende udstyr TEW-753DAP overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF, 2006/95/EF, og 2009/125/EF. Hiermit erklrt TRENDnet, dass sich das Gert TEW-753DAP in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/
EG, 2006/95/EG und 2009/125/EG befindet. Kesolevaga kinnitab TRENDnet seadme TEW-753DAP vastavust direktiivi 1999/5/E, 2006/95/E ja 2009/125/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. Hereby, TRENDnet, declares that this TEW-753DAP is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC, 2006/95/EC, and 2009/125/EC. Por medio de la presente TRENDnet declara que el TEW-753DAP cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE, 2006/95/CE, 2009/125/CE y. TRENDnet TEW-753DAP 1999/5/, 2006/95/, 2009/125/ . Par la prsente TRENDnet dclare que lappareil TEW-753DAP est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE, 2006/95/CE, 2009/125/CE et Con la presente TRENDnet dichiara che questo TEW-753DAP conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE, 2006/95/CE e 2009/125/CE. Ar o TRENDnet deklar, ka TEW-753DAP atbilst Direktvas 1999/5/EK, 2006/95/EK, un 2009/125/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. iuo TRENDnet deklaruoja, kad is TEW-753DAP atitinka esminius reikalavimus ir kitas 1999/5/EB, 2006/95/EB ir 2009/125/EB Direktyvos nuostatas. Declaration of Conformity nl Nederlands
[Dutch]
mtMalti
[Maltese]
hu Magyar
[Hungarian]
pl Polski
[Polish]
pt Portugus
[Portuguese]
sl Slovensko
[Slovenian]
sk Slovensky
[Slovak]
fi Suomi
[Finnish]
sv Svenska
[Swedish]
Hierbij verklaart TRENDnet dat het toestel TEW-753DAP in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG, 2006/95/EG, en 2009/125/EG. Hawnhekk, TRENDnet, jiddikjara li dan TEW-753DAP jikkonforma mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 1999/5/KE, 2006/95/KE, u 2009/125/KE. Alulrott, TRENDnet nyilatkozom, hogy a TEW-753DAP megfelel a vonatkoz alapvet kvetelmnyeknek s az 1999/5/EK irnyelv, a 2006/95/EK s a 2009/125/EK irnyelv egyb elrsainak Niniejszym TRENDnet owiadcza, e TEW-753DAP jest zgodny z zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/WE, 2006/95/WE i 2009/125/WE. TRENDnet declara que este TEW-753DAP est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE, 2006/95/CE e 2009/125/CE. TRENDnet izjavlja, da je ta TEW-753DAP v skladu z bistvenimi zahtevami in ostalimi relevantnimi doloili direktive 1999/5/ES, 2006/95/ES, a 2009/125/ES. TRENDnet tmto vyhlasuje, e TEW-753DAP spa zkladn poiadavky a vetky prslun ustanovenia Smernice 1999/5/EF. TRENDnet vakuuttaa tten ett TEW-753DAP tyyppinen laite on direktiivin 1999/5/EY, 2006/95/EY ja 2009/125/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Hrmed intygar TRENDnet att denna TEW-753DAP str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG, 2006/95/EG och 2009/125/EG. 50 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TEW-753DAP 3 Years Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty. If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defective product or part and deliver an equivalent product or part to the customer. The repair/replacement units warranty continues from the original date of purchase. All products that are replaced become the property of TRENDnet. Replacement products may be new or reconditioned. TRENDnet does not issue refunds or credit. Please contact the point-of-purchase for their return policies. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. There are no user serviceable parts inside the product. Do not remove or attempt to service the product by any unauthorized service center. This warranty is voided if (i) the product has been modified or repaired by any unauthorized service center, (ii) the product was subject to accident, abuse, or improper use (iii) the product was subject to conditions more severe than those specified in the manual. Warranty service may be obtained by contacting TRENDnet within the applicable warranty period and providing a copy of the dated proof of the purchase. Upon proper submission of required documentation a Return Material Authorization (RMA) number will be issued. An RMA number is required in order to initiate warranty service support for all TRENDnet products. Products that are sent to TRENDnet for RMA service must have the RMA number marked on the outside of return packages and sent to TRENDnet prepaid, insured and packaged appropriately for safe shipment. Customers shipping from outside of the USA and Canada are responsible for return shipping fees. Customers shipping from outside of the USA are responsible for custom charges, including but not limited to, duty, tax, and other fees. WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMERS SOLE REMEDY SHALL BE, AT TRENDNETS OPTION, REPAIR OR REPLACE. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME Warranty FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF TRENDNETS PRODUCTS. TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMERS OR ANY THIRD PERSONS MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD. LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT TRENDNETS OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. Governing Law: This Limited Warranty shall be governed by the laws of the state of California. Some TRENDnet products include software code written by third party developers. These codes are subject to the GNU General Public License (GPL) or GNU Lesser General Public License (LGPL). Go to http://www.trendnet.com/gpl or http://www.trendnet.com Download section and look for the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these codes. Please go to http://www.gnu.org/licenses/gpl.txt or http://www.gnu.org/licenses/
lgpl.txt for specific terms of each license. DRAFT TEW-753DAP Users Guide V1.0 51 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved. Warranty 52 TEW-753DAP Users Guide Copyright 2013 TRENDnet. All rights reserved.
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2013-09-13 | 5745 ~ 5825 | DTS - Digital Transmission System | Original Equipment |
2 | 5180 ~ 5240 | NII - Unlicensed National Information Infrastructure TX |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2013-09-13
|
||||
1 2 | Applicant's complete, legal business name |
TRENDNET, Inc.
|
||||
1 2 | FCC Registration Number (FRN) |
0019225663
|
||||
1 2 | Physical Address |
20675 Manhattan Place
|
||||
1 2 |
Torrance, California 90501
|
|||||
1 2 |
United States
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
c******@curtis-straus.com
|
||||
1 2 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
XU8
|
||||
1 2 | Equipment Product Code |
TEW753DAP
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
W******** T****
|
||||
1 2 | Title |
Sr. Product Manager
|
||||
1 2 | Telephone Number |
310-9******** Extension:
|
||||
1 2 | Fax Number |
310-9********
|
||||
1 2 |
w******@trendnet.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | DTS - Digital Transmission System | ||||
1 2 | NII - Unlicensed National Information Infrastructure TX | |||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | N600 High Power Dual Band PoE Access Point | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Original Equipment | ||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Power listed is the maximum combined conducted output power. End users and installers must be provided with operating and installation instructions to ensure RF exposure compliance. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product guidelines. | ||||
1 2 | Power listed is the maximum combined conducted output power. End users and installers must be provided with operating and installation instructions to ensure RF exposure compliance. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter product guidelines. Operations in the 5.15GHz - 5.25GHz band are restricted to indoor usage only. | |||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
Bureau Veritas CPS (H.K.) Ltd., Taoyuan Branch
|
||||
1 2 | Name |
R******** C********
|
||||
1 2 | Telephone Number |
+886-******** Extension:
|
||||
1 2 | Fax Number |
+886-********
|
||||
1 2 |
r******@tw.bureauveritas.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | CC MO | 2412 | 2462 | 0.56 | |||||||||||||||||||||||||||||||||||
1 | 2 | 15C | CC MO | 5745 | 5825 | 0.544 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15E | CC MO | 5180.00000000 | 5240.00000000 | 0.0470000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC