submitted | available | document details (if available) | source link |
---|---|---|---|
August 14 2014 | August 14 2014 | Microsoft Word - DDW36C Safety_Install_Manual_Insert_20140813 1040 ahsia Acrobat Distiller 8.1.0 (Windows) |
various | User Manual | Users Manual | 45.89 KiB | August 14 2014 |
Ubee Interactive www.ubeeinteractive.com DDW36C Advanced Wireless Gateway -
Safety and Installation Product Insert to provide Federal Communications Commission
(FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna Increase separation between the equipment and receiver. the Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Regulatory Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any including interference that may cause undesired operation. interference received, FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. 1 Ubee DDW36C Safety and Installation Product Insert v1.0 Ubee Interactive www.ubeeinteractive.com Operation within 5.15 ~ 5.25 GHz frequency range is restricted to indoor environment. 1. Do not use this device in a humid space, in the rain, or near splashing water. FCC Radiation Exposure Statement:
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated at a minimum distance of 38cm between itself and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. these Safety Notices Read carefully before operating the device. It is important to be aware of these safety instructions. Install the device according to these instructions and keep this guide for future reference. instructions 2. Do not install during thunder or lightning storms. 3. Do not cover any ventilation openings in the device case. 4. Do not place the device near heat sources such as radiators or stoves. 5. Clean the device only with a clean, dry cloth. Do not use liquid or chemical cleaners. 6. Avoid static discharge when touching the device by first touching the coaxial connector of the coaxial cable. 7. Installation of the device should include grounding the coaxial cable to the earth at the building entrance per ANSI/NFPA 70 and the National Electrical Code (NEC, in particular, Section 820.93, Grounding of the Outer Conductive Shield of a Coaxial Cable). The device is designed for IT power systems with 2 Ubee DDW36C Safety and Installation Product Insert v1.0 Ubee Interactive www.ubeeinteractive.com phase-to-phase voltage at 100-120V. instructions. 8. Disconnecting the Device: If the device becomes damaged or encounters some other abnormality, disconnect the power plug from the AC wall outlet immediately. 14. Do not dispose of the device in a trash container. Please recycle. 9. The device should be installed in a location not to exceed the maximum temperature of 40 degrees Fahrenheit). degrees Celsius
(104 10. When this device is placed upright with the aid of the stand, the stand must be fixed at a 90-degree angle to the device. Otherwise, the device will have the risk of tipping over. 11. Keep the device away from Children and Pets. 12. Place the device on a cool surface. Failure to do so may result in overheating which can cause extreme damage. 13. Do not modify or attempt to disassemble the the it only according device. Use to Installation To install this device, follow the procedures below and refer to the following page for a connection diagram. 1. Connect one end of a coaxial cable (not included) to the CABLE port on the device. 3 Ubee DDW36C Safety and Installation Product Insert v1.0 Ubee Interactive www.ubeeinteractive.com Connect the other end to a cable splitter or the cable wall outlet. Be sure not to bend or over tighten the cables as this may strain the connector and cause damage. If you plan to connect the device and a television to the same cable wall outlet, you must use a cable line splitter (not included). 2. Connect one end of the supplied Ethernet cable to one of the ETHERNET ports (ETH1 to ETH4) on the device. Connect the other end to the ETHERNET port on a PC. Note:
Category 5e or Category 6 Ethernet cables with RJ-45 connectors must be used when connecting Ethernet devices to the LAN ports. This ensures Gigabit Ethernet speeds (unless the computer does not support it). 3. Connect the power cord to the POWER port on the device. Plug the other end of the power cord into the AC wall outlet. Important: Use only the power cord that is shipped with the device. Additional Information 1. RESET Button (back of device): This button resets the device to factory defaults. Using a pointed object, insert it into the button opening, and hold for more than 10 seconds. The device will reset and reboot. Note: Not all 4 Ubee DDW36C Safety and Installation Product Insert v1.0 Ubee Interactive www.ubeeinteractive.com parameters are reset to factory defaults. Refer to the User Guide for more information. 2. WPS button (top of device): The WPS button is used for the Wi-Fi Protected Setup (WPS) method to connect a Wi-Fi device to the DEVICE. Refer to the User Manual for more information. LEDs and Other Device Indicators See the following diagram and descriptions of the devices LED behavior, and the behavior of the back-panel Ethernet indicators PowerIf On, indicates that the device has successfully completed internal power-on tests. LED flashes if power-on fails. Note that the LED flashes briefly immediately after powering the device. DSWhen the DS locks on to channels, the LED is On. When the DS SCAN IN PROGRESS, the LED flashes. USWhen the US locks on to channels, the LED is On. When the US SCAN IN PROGRESS, the LED flashes. ONLINEWhen the device is obtaining an IP address and configuration file, the LED flashes. When device obtains these items, the LED is On. 2.4G Wi-FiWhen 2.4G Wi-Fi is enabled, the LED is On. When 2.4G Wi-Fi is disabled, the LED is Off. When passing 2.4G Wi-Fi network traffic, the LED flashes. 5G Wi-FiWhen 5G Wi-Fi is enabled, the LED is On. When 5G Wi-Fi is disabled, the LED is Off. When passing 5G Wi-Fi network traffic, the LED 5 Ubee DDW36C Safety and Installation Product Insert v1.0 Ubee Interactive www.ubeeinteractive.com flashes. MoCAWhen MoCA is enabled, the LED is On. When MOCA is disabled, the LED is Off. When passing Moca network traffic, the LED flashes. 6 Ubee DDW36C Safety and Installation Product Insert v1.0
This product uses the FCC Data API but is not endorsed or certified by the FCC