| submitted | available | document details (if available) | source link |
|---|---|---|---|
| December 14 2010 | December 14 2010 | UniFi Enterprise WiFi System User Guide Rob Rohm Adobe PDF Library 9.9 |
| various | User Guide | Users Manual | 4.64 MiB | December 14 2010 |
Enterprise WiFi System UniFi Enterprise WiFi System User Guide Table of Contents Table of Contents Chapter 1:
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Network Topology Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Chapter 2:
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Chapter 3:
Using the UniFi Controller Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Access Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Guests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Recent Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Admin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Appendix A:
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Appendix B:
Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 FCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Industry Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Appendix C:
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 General Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Appendix D:
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Ubiquiti Networks Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 Ubiquiti Networks, Inc. i UniFi Enterprise WiFi System User Guide Chapter 1:
Product Overview Thank you for purchasing the Ubiquiti UniFi Enterprise WiFi System. The UniFi Enterprise WiFi System includes the UniFi Controller software that allows you to manage your wireless network using your Web browser. The UniFi Enterprise WiFi System also includes the necessary hardware for mounting the unit on a wall or a ceiling. The UniFi Enterprise WiFi System supports Passive PoE which works with the included PoE adapter. If you want to power the UniFi AP from an 802.3af compliant switch, Ubiquiti Networks offers the optional Instant 802.3af Adapter to instantly transform any PoE device into a fully 48V 802.3af compliant product. Product details are available on our website at http://ubnt.com/8023af Package Contents Chapter 1: Product Overview System Requirements Microsoft Windows XP, Windows Vista, Windows 7, or Mac OS X Java Runtime Environment 1.6 (or above) Web Browser: Mozilla Firefox, Google Chrome, or Microsoft Internet Explorer 8 (or above) Network Topology Requirements A DHCP-enabled network (for AP to obtain an IP as well as for the wireless clients after the deployment) Access point(s) and the management station computer connected to the same layer-2 network. Enterprise AP Enterprise AP Wall Mount Switch UniFi Enterprise AP Wall-Mount Bracket Ceiling-Mount Plate UniFi Controller CD with User Guide Quick Start Guide 24v PoE Adapter Power Cord M3X30 Flat Head M3 Nut with Tooth M2.9x20 Self Tapping Screw (Qty. 3) Washer (Qty. 3) Screw (Qty. 3) M3x20 Screw Anchor (Qty. 3) Computer to be used as Management Station Sample Network Diagram Enterprise AP Ubiquiti Networks, Inc. 1 UniFi Enterprise WiFi System User Guide Chapter 1: Product Overview Front Back Reset Button The reset button serves two functions:
Restart It will restart the device when you press and release it quickly. Restore Factory Defaults When you press and hold it for more then 5 seconds, it will restore the device to the factory default settings. Ethernet Port Connects to the 24v PoE Adapter to provide power to the unit. LED Indicates the status of the device. See the table below for details. LED Color Flashing Amber Status Initializing Steady Amber Factory default, waiting to be integrated Alternating Amber/Green Quickly Flashing Green Steady Green Device is busy, do not touch or unplug it, this usually indicates a process such as a firmware upgrade is taking place This is used to locate an AP. When you click on Locate in the UniFi Controller software, the AP will blink. It will also display the location of the AP on the map. Indicates the device has been successfully integrated into a network and is working properly Ubiquiti Networks, Inc. 2 Chapter 2: Installation Below is an overview of the Power over Ethernet connections. UniFi Enterprise WiFi System User Guide Chapter 2:
Installation Hardware Installation The UniFi Enterprise AP is powered by the included PoE
(Power over Ethernet) adapter. To install the AP, perform the following steps:
1. Connect an Ethernet cable to the Ethernet port on the UniFi Enterprise AP. 2. Connect the power cord to the power port on the PoE Adapter. Connect the other end to of the power cord to a power outlet. 3. Connect the other end of the Ethernet cable to the Ethernet port labeled POE on the PoE Adapter. Note: If you plan to mount the AP on your ceiling, perform the ceiling mount installation steps before connecting the Ethernet cable to the PoE Adapter. Power Connection Diagram Mounting the Access Point The UniFi Enterprise AP can be wall-mounted or mounted on a ceiling. Perform the following steps for the appropriate installation:
Wall-Mount 1. Align the wall-mounting bracket with the Wall Mount text facing up. There are horizontal and vertical lines on the bracket to help with orientation. Wall Mount Wall Mount text 2. Use a pencil to mark the holes on the wall. 3. Use a 6 mm drill bit to drill the holes in the wall. 4. Insert the 3 screw anchors into the wall. 5. Secure the wall-mount bracket to the wall by inserting the self tapping screws into the anchors. Wall Mount Ubiquiti Networks, Inc. 3 UniFi Enterprise WiFi System User Guide Chapter 2: Installation 6. Align the notches on the AP with the notches on the wall-mount bracket. Wall Mount 7. Turn the AP clockwise until it locks into place. 6. Feed the Ethernet cable through the hole and then align the Enterprise AP with the notches on the wall-
mount bracket. Wall Mount Ceiling-Mount 1. Remove the ceiling tile. 2. Align the ceiling-mount plate to the center of the top side of the ceiling tile. 3. Use a 3.5 mm drill bit to drill holes for the three flat head screws. 4. Cut or drill a circle approximately 25 mm in size that lines up with the larger circle on the ceiling-mount plate. This will be used for the Ethernet cabling. 5. Secure the wall-mount bracket and ceiling-mount plate to the ceiling tile using the 3 flathead screws and 3 nuts with tooth washers. Note: The UniFi AP supports Passive PoE which works with the included PoE adapter. If you want to power the UniFi AP from an 802.3af compliant switch, Ubiquiti Networks offers the optional Instant 802.3af Adapter to instantly transform any PoE device into a fully 48V 802.3af compliant product. Product details are available on our website at http://ubnt.com/8023af 7. Turn the AP clockwise until it locks into place. Ubiquiti Networks, Inc. 4 UniFi Enterprise WiFi System User Guide Software Installation Insert the UniFi Controller software CD into your CD-
ROM drive and follow the instructions for your specific computer type. Mac Users 1. Click on the Install icon. Chapter 2: Installation PC Users 1. Launch UniFi-installer.exe. 2. Click Install. 3. If your computer doesnt have Java 1.6 or above installed, you will be prompted to install it. Click Install to continue. 2. Click Continue and follow the on-screen instructions to install the software. 4. Click Next. 3. Go to Go > Applications and double-click the UniFi icon. 5. Be sure the Start UniFi Controller after installation option is checked and click Finish. Proceed to Configuring the UniFi Controller Software on page 6. Note: The UniFi Controller software can also be launched from Start > All Programs. Ubiquiti Networks, Inc. 5 UniFi Enterprise WiFi System User Guide Chapter 2: Installation Configuring the UniFi Controller Software 1. The UniFi Controller software startup will begin. When the option becomes available, click Launch a Browser to Manage Wireless Network. 5. Enter an admin name and password to use when accessing the management interface. Confirm your password in the Confirm field. Click Next. 2. Select your language and country. Click Next. 6. Review your settings. Click Back to make changes or Finish to save your settings. Once finished you will be redirected to the management interface via your web browser. 3. Select the devices that you want to configure and click Next. Congratulations, your wireless network is now configured. A login screen will appear for the UniFi Controller management interface. Enter the admin name and password that you created and click Login. 4. The UniFi Installation Wizard will create a secure primary wireless network for your devices. Perform the following steps:
a. Enter the wireless network name (SSID) in the Secure SSID field. b. Enter a passphrase to be used for your primary network. c. To enable guest access, select Enable Guest Access and enter a guest network name in the Guest SSID field. d. Click Next. Proceed to the next chapter for information on using the UniFi Controller software. Ubiquiti Networks, Inc. 6 Chapter 3: Using the UniFi Controller Software To add a custom map, you must first create the image using an illustration, image editing, or blueprint application that exports .jpg, .gif, or .png file formats. Once youve created the map, you can upload it to the UniFi Controller software by performing the following steps:
1. Click Configure Maps. Configure Maps button UniFi Enterprise WiFi System User Guide Chapter 3:
Using the UniFi Controller Software The UniFi Controller software that comes with your UniFi Enterprise WiFi System has a browser-based interface for easy configuration and management. To access the interface, perform the following steps:
1. Launch the UniFi Controller application if hasnt already been started. Mac users: Go > Applications > UniFi PC users: Start > All Programs > UniFi 2. The login screen will appear. Enter the admin name and password in the appropriate fields and click Login. 2. Click Add a Map. Add a Map Map The UniFi Controller software allows you to upload map images of your location(s) for a visual representation of your wireless network. When you initially launch the UniFi Controller application, a default map is displayed. 3. Browse for an image to use as a map (valid file formats are .jpg, .gif, and .png). Give the image a brief description. Click Continue. Ubiquiti Networks, Inc. 7 UniFi Enterprise WiFi System User Guide Chapter 3: Using the UniFi Controller Software 4. Click Close. 5. You can adjust the zoom using the slider on the right. icon(s) from the Unplaced APs Drag the Access Point list on the left to the appropriate location(s) on the map. The access point will appear in the area that you placed it. Access Point Shows the location of the Access Point on the map. Click and hold this icon to drag the Access Point to another location on the map. Click on the Access Point icon to reveal additional options. Click a blank area of the map to hide the additional options. Lock Locks the selected Access Point in the current location on the map. Details Brings up the Details window. This allows you to view Access Point settings and connected users. You can also edit the radio channel, transmit power, and device alias. There are 4 tabs to select from in the Details window. Details, Users, Guests, and Configuration. Details Displays details on the Access Point including the MAC address, model, version, IP address, uptime, connected users, and connected guests. Click Radio to display the channel used, transmit power, and packet information. Users Displays the hostname of the users that are connected to the selected Access Point and the IP address assigned to them. You can click on the hostname to display additional details of each user. A window with Details, Statistics, and Configuration is displayed. The Details tab displays the MAC address, hostname, IP address, uptime and the AP they are connected to. The Statistics tab displays the channel used, signal strength, transmit and receive rates, power saving enabled or disabled, and the number of packets sent and received. You can also click History to see a sortable list of events. The Configuration tab allows you to change the alias name for the device. Guests Displays the MAC address of guests that are connected to the guest network. Configuration Allows you to change the alias name of the device, the channel setting, and set the transmit power to Auto, High, Medium, or Low. You can also remove the AP if you no longer want to manage it with the UniFi software. Remove Remove the Access Point from the location on the map. Ubiquiti Networks, Inc. 8 UniFi Enterprise WiFi System User Guide Chapter 3: Using the UniFi Controller Software 3. Enter the distance that the line represents in the Distance: field. The distance is specified in meters by default but you can switch to feet using the drop-down selection menu on the right. Click Next. Show: You can select to show labels or details and wireless coverage on the map. The following are the options available:
Labels Displays the name of the Access Point. Details Displays the Access Point name, MAC address, transmit/receive channel, number of users connected, and number of guests connected. Coverage Displays a visual representation of the range covered by the Access Point. Map: If multiple maps have been uploaded, you can select which map you want to view using this option. Configure Maps Use this option to add maps or edit the current map(s). Zoom Slider Use to zoom the map detail in and out. Statistics The Statistics tab provides a visual representation of the network traffic connected to your managed APs. Charts representing the number of clients and network traffic are displayed. An hour by hour chart of the usage over the last 24 hours is also displayed on this screen. Set Map Scale Use this option to define the scale of the map. You will draw a line and define the distance that the line represents. Setting the Map Scale 1. Click the Set Map Scale button. 2. Click and hold to draw a line in the area that you want to use to set the scale of the map. If you need to redraw the line, just click and hold again to draw a new line. Once youre happy with the line, click Next. Access Points The Access Points tab displays a list of managed Access Points with their name, IP address, status, number of clients connected, download/upload statistics, and their transmit/receive channel. Search Allows you to search the tables for any information that is displayed. Ubiquiti Networks, Inc. 9 UniFi Enterprise WiFi System User Guide Chapter 3: Using the UniFi Controller Software Name/Mac Address Displays the hostname, alias, or MAC address of the Access Point. You can click on the name to get additional details on the Access Point. IP Address Displays the IP address of the Access Point. Status Displays the connection status information. Num Clients Displays the number of clients connected to the Access Point. Download Displays the total size of downloads via the Access Point. Upload Displays the total size of uploads via the Access Point. Channel Displays the transmit/receive channel being used by the Access Point. Actions Select an action button to perform the desired action:
Restart Restart the selected Access Point. Locate Locate the Access Point on the map. The LED on unplaced APs will flash to indicate which AP it is so that you can place it in the correct location on the map. Upgrade When Automatic Upgrade is enabled, the Access Points will be automatically upgraded. The Upgrade option is used to manually update the firmware on the Access Point. Users The Users tab displays a list of users that are connected to the primary wireless network of the Access Point. Activity Displays the level of activity for each user. Bars Activity Level
(Bytes per second) Idle 500 8000 64000 512000 2048000 Uptime Displays the total time the user has been connected for this session. Actions Click an action button to perform the appropriate action. Block Click this to block a specific user from accessing the Access Point. This will add the client to the Blocked Device list. Reconnect Click this button to reconnect a specific user to the Access Point. Guests The Guests tab displays a list of users that have connected to the guest network of the Access Point. Name/MAC Address Displays the hostname, alias, or MAC address of the connected user. You can click on the name to get additional details. IP Address Displays the IP address assigned to the user. Access Point Displays the hostname or alias of the Access Point. You can click on the name to get additional details on the Access Point. Signal Displays the signal strength from the AP to the client. Up Displays the total size of files uploaded from the user. Down Displays the total size of files downloaded from the user. Name/MAC Address Displays the hostname, alias, or MAC address of the connected guest. You can click on the name to get additional details. Status Indicates whether the guest is authorized or not. For authorization, guests must accept the Terms of Use if the guest portal is enabled and authenticate if authentication is enabled. IP Address Displays the IP address assigned to the guest. Access Point Displays the hostname or alias of the Access Point. You can click on the name to get additional details on the Access Point. Signal Displays the signal strength from the AP to the client. Up Displays the total size of files uploaded from the guest. Down Displays the total size of files downloaded from the guest. Ubiquiti Networks, Inc. 10 UniFi Enterprise WiFi System User Guide Chapter 3: Using the UniFi Controller Software AP The upper part of the window has 4 clickable tabs. The bottom of the window has a Locate and Restart button. Use the Locate button to flash the LED on the Access Point and flash the Access Point icon on the map. Use the Restart button to restart the Access Point. The 4 tabs contain the following information:
Details Displays details on the Access Point. Click Radio to display the channel and transmit/receive statistics. Overview Activity Displays the level of activity for each guest. Bars Activity Level
(Bytes per second) Idle 500 8000 64000 512000 2048000 Uptime Displays the total time the user has been connected for this session. Actions Click an action button to perform the appropriate action. Block Click this to block a specific guest from accessing the Access Point. Reconnect Click this button to reconnect a specific guest to the Access Point. Recent Events Displays a list of recent events including the date and time the event occurred and the details of the event. The user and AP names are clickable links. Event Slider Move the slider right and left to navigate between pages of events. Search Allows you to enter text you want to search for. Simply begin typing, there is no need to press enter. Clicking on an Event Device Link The event messages have clickable links [in brackets underlined in gray text] for access points and users/
guests. Details vary based on the selection. MAC address Displays the MAC address of the Access Point. Model Displays the model information. Version Displays the version of software used on the Access Point. IP address Displays the IP address of the Access Point. Uptime Displays the amount of time the Access Point has been running without interruption.
# Users Displays the number of users connected to the primary network.
# Guests Displays the number of users connected to the guest network. Ubiquiti Networks, Inc. 11 UniFi Enterprise WiFi System User Guide Chapter 3: Using the UniFi Controller Software Radio (11n/b/g) Click Radio to display the channel and transmit/receive statistics. Users Name Displays the name (MAC address if not defined) of users connected to the primary network of the selected Access Point. You can click on the name to display additional details of each user (see User/Guest on the following page) or click a button to perform the appropriate action. WLAN Displays the SSID (network name) of the wireless network the user is connected to. Actions Select from one of the following actions:
Block Click this to block a specific user from accessing the Access Point. This will add the client to the Blocked Device list. Reconnect Click this button to reconnect a specific user to the Access Point. Channel Displays the wireless channel being used. Transmit Power Displays the transmit power. TX Pkts / Bytes Displays the number of packets and total bytes transmitted by the Access Point. RX Pkts / Bytes Displays the number of packets and total bytes received by the Access Point. TX Retry / Dropped Displays the percentage of transmitted packets that needed to be resent and the percentage of packets that were dropped. RX Error / Dropped Displays the percentage of packets received that needed to be resent and the percentage of packets that were dropped.
# Users Displays the number of users connected to the primary network.
# Guests Displays the number of users connected to the guest network. Ubiquiti Networks, Inc. 12 UniFi Enterprise WiFi System User Guide Chapter 3: Using the UniFi Controller Software Guests Configuration Allows you to change device configuration settings. Be sure to click the Apply button to apply any changes that you make. Config Name Displays the name (MAC address if not defined) of users connected to the guest network of the selected Access Point. You can click on the name to display additional details of each user (see User below) or click a button to perform the appropriate action. WLAN Displays the SSID (network name) of the wireless network the guest is connected to. Actions Select from one of the following actions:
Block Click this to block a specific user from accessing the Access Point. This will add the client to the Blocked Device list. Reconnect Click this button to reconnect a specific user to the Access Point. Alias Allows you to name the device. Channel Select a channel or leave the default auto setting. You can also use the default HT20 for 20 MHz operation or HT40 for 40 MHz operation. Tx Power By default the transmit power is set to Auto. You can also manually select High, Medium, or Low. Remove Remove You can remove the AP if you no longer want to manage it with the UniFi software. Ubiquiti Networks, Inc. 13 UniFi Enterprise WiFi System User Guide Chapter 3: Using the UniFi Controller Software User/Guest The User and Guest hyperlinks bring up a window with 4 clickable tabs. The 4 tabs contain the following information:
Overview Channel Displays the channel being used for wireless communication. Signal Displays the signal level. TX Rate Displays the transmit rate. RX Rate Displays the reception rate. Activity Displays user activity. Power Save Indicates whether power saving is enabled. Received Pkts / Bytes Displays the number of packets and total bytes transmitted by the user. Sent Pkts / Bytes Displays the number of packets and total bytes received by the user. History MAC address Displays the MAC address of the Access Point. Hostname Displays the name (if defined). IP address Displays the IP address of the Access Point. Uptime Displays the amount of time the Access Point has been running without interruption. Connected AP Displays the name or MAC address of the Access Point this user is connected to. Statistics Date/Time Displays the date and the time the user connected to the Access Point. Duration Displays the time duration that the user was connected to the Access Point. Down Displays how many bytes were downloaded by the user during the session. Up Displays how many bytes were uploaded by the user during the session. ESSID Displays the wireless network name (SSID) of the network that the user is connected to. Connected AP Displays the MAC address or name of the Access Point the user is connected to. Ubiquiti Networks, Inc. 14 UniFi Enterprise WiFi System User Guide Chapter 3: Using the UniFi Controller Software Configuration Config Alias Allows you to enter a name for the user. Be sure to click Apply to save your name change. Debug Show Archived Show all of the alert messages that have been archived. Archive All Archive all of the alert messages displayed on the screen. Adopt Click this button to adopt an access point that is waiting for adoption. Archive Archive the selected alert message. Settings System System related settings. Guest Control Guest portal and policies. Wireless Networks Wireless networks. Blocked Devices List of blocked wireless devices. Settings >> System Debug Allows you to force a device to connect to a specific Access Point. Alerts Important events are displayed in the alerts window. The date and time of the event and the message are displayed. Search Allows you to enter text you want to search for. Simply begin typing, there is no need to press enter. System Configuration System Name Editable field with the system name. Country Select your country from the drop-down list. Services Automatic Upgrade When enabled, this option will automatically upgrade your firmware when an update is available. Network Discovery When enabled, this option allows UniFi to be discoverable via UPnP. This option is enabled by default. Remote Logging Enable to define a remote syslog server. Enter the IP address and port of the syslog server. Be sure to click Apply to save any changes that you have made. Ubiquiti Networks, Inc. 15 UniFi Enterprise WiFi System User Guide Chapter 3: Using the UniFi Controller Software Settings >> Guest Control Settings >> Wireless Networks Guest Policies Guest Portal This option is disabled by default. When disabled, guests can access the Internet without entering a password or accepting terms of use. When this option is enabled, you can control the guest access portal. You can select from the following authentication and landing page controls:
Authentication No authentication When this option is selected, guests are not required to login but will be required to accept the Terms of Use before gaining access to the Internet. Wireless Configurations Name Displays the wireless network name (SSID). Security Displays the type of security being used on your wireless network. Guest Network Indicates whether the network is a guest network. Actions Select an action button to perform the desired action:
Edit Select Edit to make changes to the wireless network settings. Delete Select to delete the wireless network. Wireless Configuration Simple Password When this option is selected, guests are required to enter the simple password entered here and are required to accept the Terms of Use before gaining access to the Internet. External Portal Server Enter the IP address of your external server if you have a custom guest portal. Landing Page Redirect to the original URL When this option is selected, guests are directed to the URL they requested after accepting the terms of use. Promotional URL When this option is selected, guests are redirected to the URL that you specify here after accepting the terms of use. Be sure to specify the URL with http:// in front of the web address. Example: http://www.ubnt.com Access Control Restricted Subnets Enter in any subnets that you dont want guests to be able to access. Name/SSID Allows you to edit the wireless network name (SSID). Security Selects the type of security to use on your wireless network.
- Open This option is typically only used on the Guest network. When enabled, wireless network access is open to anyone without needing a password.
- WEP WEP (Wired Equivalent Privacy) is the oldest and least secure security algorithm. WPA security methods should be used when possible. WEP Key Enter a WEP encryption key in hexadecimal format. You can enter a 64-bit or 128-
bit key:
Type 64-bit HEX 10 Hexadecimal Characters (0-9, A-F or a-f) Example: 00112233AA 128-bit 26 Hexadecimal Characters (0-9, A-F or a-f) Example: 00112233445566778899AABBCC Ubiquiti Networks, Inc. 16 UniFi Enterprise WiFi System User Guide Chapter 3: Using the UniFi Controller Software Admin Server Information Version The software version is displayed here. If there is an update, UniFi will automatically download it and display it here. Backup Download Backup Settings Click to download a file that contains all of your settings so you can restore them later if you choose. Restore Choose File Select this option to restore settings from a backup file that youve already downloaded. Support Info Download Support Info Select this option to download a file to your computer with information about your configuration that can be emailed to our support team. Key Index Specifies the Index of the WEP Key used. 4 different WEP keys can be configured at the same time, but only one is used. The effective key is set by choosing 1, 2, 3 or 4.
- WPA-Personal WPA or Wi-Fi Protected Access was developed as a stronger encryption method over WEP. WPA-Personal requires a passphrase to connect to the wireless network. Security Key Enter the passphrase that users will use to connect to the wireless network.
- WPA-Enterprise WPA Enterprise uses a RADIUS server to authenticate users on the wireless network. IP Address This is where the IP address of the RADIUS server is specified. Port The port number is entered here. By default it is 1812. Password The password used to authenticate on the RADIUS server is entered here. Guest Policy Select this option to enable guest access policies on this wireless network. Advanced
- VLAN To use a VLAN, select Use VLAN ID and enter the port number.
- Hide SSID Select this option if you dont want the SSID to be broadcast.
- Priority Defines the traffic priority, low, medium, or high. Be sure to click Apply to save any changes that you have made. Click Cancel to discard changes. Settings >> Admin Settings Admin Name Displays the current admin name used to login. To change the admin name, simply enter a new name and click Apply. Password A new password can be entered in this field. Be sure to enter the password again in the Confirm field and then click Apply to save your new password. Confirm Used to confirm your new password. Language Selects the language for use in the interface. Ubiquiti Networks, Inc. 17 Appendix A: Specifications 20 x 20 x 3.65 cm 290 g
(430 g with mounting kits) Ethernet (Auto MDX, autosensing 10/100 Mbps) Reset 2 Integrated
(supports 2x2 MIMO with spatial diversity) 802.11 b/g/n*
Passive Power over Ethernet
(1224V) 24V 1A PoE Adapter included UniFi Enterprise WiFi System User Guide Appendix A:
Specifications Dimensions Weight Ports Buttons Antennas WiFi Standards Power Method Power Supply Maximum Power Consumption Max TX Power BSSID Power Save Wireless Security Certifications Mounting Operating Temperature 10C to 70C (14F to +158 F) Operating Humidity 4W 23 dBm Up to four per radio Supported WEP, WPAPSK, WPATKIP, WPA2 AES, 802.11i CE, FCC, IC Wall/Ceiling (Kits included) 5% 80% Condensing Advanced Traffic Management VLAN 802.1Q WLAN prioritization Advanced QoS Supported Guest traffic isolation Voice, video, best effort, and WMM background 100+
Concurrent Clients Supported Data Rates (Mbps) 802.11n 802.11b 802.11g MCS0 MCS15 (6.5 Mbps to 300 Mbps), HT 20/40 1, 2, 5.5, 11 6, 9, 12, 18, 24, 36, 48, 54
* 2.4GHz Ubiquiti Networks, Inc. 18 Appendix B: Compliance Information UniFi Enterprise WiFi System User Guide Appendix B:
Compliance Information FCC Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provice reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The antennas used for this transmitter must be installed to provide a separation distance of at least the following from all users:
20 cm Industry Canada This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe A est confrome la norme NMB-003 Canada. Operation is subject to the following two conditions:
1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio inteference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. Ubiquiti Networks, Inc. 19 Appendix C: Warranty Disclaimer UBIQUITI NETWORKS does not warrant that the operation of the products is error-free or that operation will be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any nature or description relating to system performance, including coverage, buyers selection of products for buyers application and/or failure of products to meet government or regulatory requirements. UniFi Enterprise WiFi System User Guide Appendix C:
Warranty General Warranty UBIQUITI NETWORKS, Inc (UBIQUITI NETWORKS) represents and warrants that the Products furnished hereunder shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS sole and exclusive obligation under the foregoing warranty shall be to repair or replace, at its option, any defective Product that fails during the warranty period. The expense of removal and reinstallation of any item is not included in this warranty. The foregoing warranty is exclusive and in lieu of all other warranties, express or implied, including the implied warranties of merchantability and fitness for a particular purpose and any warranties arising from a course of dealing, usage or trade practice with respect to the products. Repair or replacement in the manner provided herein shall be the sole and exclusive remedy of Buyer for breach of warranty and shall constitute fulfillment of all liabilities of UBIQUITI NETWORKS with repect to the quality and performance of the Products. UBIQUITI NETWORKS reserves the right to inspect all defective Products (which must be returned by Buyer to UBIQUITI NETWORKS factory freight prepaid). No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned to Buyer freight collect. UBIQUITI NETWORKS shall have no obligation to make repairs or replacement necessitated by catastrophe, fault, negligence, misuse, abuse, or accident by Buyer, Buyers customers or any other parties. The warranty period of any repaired or replaced. Product shall not extend beyond its original term. Warranty Conditions The foregoing warranty shall apply only if:
(I) The Product has not been subjected to misuse, neglect or unusual physical, electrical or electromagnetic stress, or some other type of accident.
(II) No modification, alteration or addition has been made to the Product by persons other than UBIQUITI NETWORKS or UBIQUITI NETWORKS authorized representatives or otherwise approved by UBIQUITI NETWORKS.
(III) The Product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation. Ubiquiti Networks, Inc. 20 Appendix D: Contact Information UniFi Enterprise WiFi System User Guide Appendix D:
Contact Information Ubiquiti Networks Support Ubiquiti Support Engineers are located in the U.S. and Europe and are dedicated to helping customers resolve software, hardware compatibility, or field issues as quickly as possible. We strive to respond to support inquiries within a 24 hour period. Email: support@ubnt.com Phone: 408-942-1153 (9 a.m. - 5 p.m. PST) Skype: Ubiquiti_Support Online Resources Wiki Page: www.ubnt.com/wiki Support Forum: www.ubnt.com/forum Knowledge Base: www.ubnt.com/kb Downloads: www.ubnt.com/support/downloads 91 E. Tasman Drive San Jose, CA 95134 www.ubnt.com 2010 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti Networks, Inc. 21
This product uses the FCC Data API but is not endorsed or certified by the FCC