5 GHz Point to Point 1.0+ Gbps Radio Models: AF5, AF5U Introduction Introduction Thank you for purchasing the Ubiquiti Networks airFiber 5GHz Point-to-Point 1.0+ Gbps Radio. This Quick Start Guide is designed to guide you through the installation, show you how to access the airFiber Configuration Interface, and explain how to set up an airFiber link. This Quick Start Guide also includes the warranty terms and is for use with the following models:
Model AF5 AF5U Description Operating Frequency*
Supports mid-band frequencies 5470 - 5950 MHz Supports high-band frequencies 5725 - 6200 MHz
* Refer to the Specifications section for more information. Package Contents airFiber AF5 I-Bracket Upper Mount Bracket with Elevation Rod Lower Mount Bracket Pole Clamps M10x150 Carriage M10x100 Carriage
(Qty. 2) Bolts (Qty. 4) Bolts (Qty. 2) M8x14 Serrated Flange Bolts (Qty. 4) Azimuth Support Brackets
(Qty. 2) Flat Washers
(M10, Qty. 6) Lock Washers
(M10, Qty. 6) Hex Nuts
(M10, Qty. 6) Cable Ties
(Qty. 2) GigE PoE Adapter Power Cord Quick Start Guide
(50V, 1.2A) 5 GHz Point to Point 1+ Gbps Radio Models: AF5, AF5U TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable is designed for outdoor installations. It is the customers responsibility to follow local country regulations, including operation within legal frequency channels, output power, and Dynamic Frequency Selection (DFS) requirements. 1 airFiber AF5/AF5U Quick Start Guide Hardware Overview Side Lanyard Attachment Loop Elevation Rod Hex Nut to adjust Elevation Rod Pre-Installed M10 x25 Flanged Bolts Grounding Point Lanyard Attachment Loop Assembled View 2 Interfaces Hardware Overview Interface Description Reset Button To reset to factory defaults, press and hold the Reset button for more than five seconds while the unit is already powered on. Remote Display Displays the received signal strength in dBm of the remote airFiber radio. Local Display Displays the received signal strength in dBm of the local airFiber radio. Management Port 10/100 Mbps, secured port for configuration. By default, this is the only port that can monitor, configure, and/or update firmware. Aux Port Data Port Port for audio tone aiming. 10/100/1000 Mbps port handles all user traffic. 3 airFiber AF5/AF5U Quick Start Guide LEDs LED State Status GPS Master Off On No GPS Synchronization Operational (Strong Signal) Normal Flash*
Non-Operational (Weak Signal) Off On Off Short Flash*
Slave mode Master mode RF Off Syncing Link Status Normal Flash*
Beaconing Long Flash*
Registering On On Operational Displays the received signal strength in dBm of the remote airFiber radio. Remote 4 Hardware Overview LED State Status Local On Displays the received signal strength in dBm of the local airFiberradio. Overload Fast Flash Overload Condition
(reserved) 8x 6x 4x to 0.25x On On On 256QAM MIMO 64QAM MIMO 16QAM MIMO Long Flash*
QPSK MIMO Normal Flash*
1x QPSK xRT**
Short Flash*
x QPSK xRT**
* Short Flash (1:3 on/off cycle) Normal Flash (1:1 on/off cycle) Long Flash (3:1 on/off cycle)
** xtreme Range Technology Port LEDs LED State Status t n e m e g a n a M Act Speed Act Off On No Ethernet Link Ethernet Link Established Random Flashing Ethernet Activity Off On Off On 10 Mbps 100 Mbps No Ethernet Link Ethernet Link Established Random Flashing Ethernet Activity a t a D Speed Off On 10/100 Mbps 1000 Mbps 5 airFiber AF5/AF5U Quick Start Guide Installation Requirements Pre-Assembly Tool 13 mm (") wrench Pole-Mounting Tool 17 mm (11/16") wrench Other Requirements Clear line of sight between airFiber radios Clear view of the sky for proper GPS operation Vertical mounting orientation Mounting location with < 0.5 displacement due to twist and sway under wind loading Mounting point:
At least 1 m (3.28 ft) below the highest point on the structure For tower installations, at least 3 m (9.84 ft) below the top of thetower Ground wires min. 10 AWG (5 mm2) and max. length:
1m(3.28ft). As a safety precaution, ground the airFiber radios to grounded masts, poles, towers, or grounding bars. WARNING: Failure to properly ground your airFiber units will void your warranty.
(Recommended) 2 Outdoor GigE PoE surge protectors Note: For guidelines about grounding and lightning protection, follow your local electrical regulatory codes. Outdoor, shielded Category 6 (or above) cabling and shielded RJ-45 connectors are required for all wired Ethernet connections. 6 Installation Overview Installation Overview We recommend that you configure your paired airFiber radios before mounting. Below is an overview of the installation with specific details in the following instructions:
Connect Power over Ethernet to the Data port, and connect an Ethernet cable between your computer and the Managementport. Configure the device settings in the airFiber Configuration Interface. Once configuration is complete, disconnect the cables to move the airFiber radios. Pre-assemble the mounting hardware. Install the airFiber radios at the site. Establish and optimize the RF link. Note: The AF5 and AF5U models share the same installation and configuration instructions. Connecting Power over Ethernet 1. Push the button and slide the port cover down to access cableports. (The port cover cannot be completely removed.) 7 airFiber AF5/AF5U Quick Start Guide 2. Connect an Ethernet cable to the Data port. 3. Connect the other end of the Ethernet cable from the Data port to the Ethernet port labeled POE on the GigE PoE Adapter. 4. Connect the Power Cord to the power port on the GigE PoE Adapter. Connect the other end of the Power Cord to a powersource. 8 airFiber Configuration airFiber Configuration The instructions in this section explain how to access the airFiber Configuration Interface and configure the following settings:
Wireless Mode Configure one airFiber radio as the Master and the other as the Slave. Duplex The airFiber radio supports both half-duplex and full-duplex operation. Half-duplex operation provides more frequency planning options at the cost of higher latency and throughput. Full-duplex operation provides the highest throughput and lowest latency; however, you have fewer frequency management options.
- Half Duplex (default) The TX and RX Frequencies can be the same or different to suit local interference. RX RX F r e q u e n c y A Frequency A TX Master TX Slave Half-Duplex Diagram
- Full Duplex The TX and RX Frequencies should be different. RX RX F r e q u e n c y A Frequency B TX Master TX Slave Full-Duplex Diagram TX and RX Frequencies The TX Frequency on the Master must match the RX Frequency on the Slave, and vice versa. 9 airFiber AF5/AF5U Quick Start Guide 1. Connect an Ethernet cable from your computer to the Management port on the airFiber radio. 2. Configure the Ethernet adapter on your computer with a static IP address on the 192.168.1.x subnet. 3. Launch your web browser. Type http://192.168.1.20 in the address field and press enter (PC) or return (Mac). 4. The login screen will appear. Enter ubnt in the Username and Password fields. Select your Country and Language. You must agree to the Terms of Use to use the product. Click Login. Note: U.S. product versions are locked to the U.S. Country Code to ensure compliance with FCC regulations. 10 5. Click the Wireless tab. airFiber Configuration 6. Enter the Basic Wireless Settings:
a. For one airFiber radio, select Master from the Wireless Mode drop-down. For the other airFiber radio, keep the default, Slave. b. Enter a name in the Link Name field. This should be the same on both the Master and the Slave. c. For the Duplex drop-down:
- Half Duplex The default mode. The TX and RX Frequencies can be the same or different to suit local interference.
- Full Duplex The TX and RX Frequencies should be different. d. Select a TX Frequency. This must match the RX Frequency on your other airFiber radio. e. Select a RX Frequency. This must match the TX Frequency of f. your other airFiber radio. If needed, change the Output Power and/or Maximum Modulation Rate settings. 11 airFiber AF5/AF5U Quick Start Guide 7. Configure the Wireless Security:
a. Select the AES Key Type, HEX or ASCII. b. For the Key field:
- HEX Enter 16 bytes (eight, 16-bit HEX values: 0-9, A-F, or a-f). You can omit zeroes and use colons, similar to the IPv6 format. Note: The airFiber Configuration Interface supports IPv6 formats excluding dotted quad and "::"
(double-colon) notation.
- ASCII Enter a combination of alphanumeric characters (0-9, A-Z, or a-z). 8. Click Change and then click Apply. 9. In-Band Management is enabled by default, so each airFiber radio must have a unique IP Address. (If the airFiber radios use the same IP Address, then you may lose access to the airFiber radios via the Data ports.) Click the Network tab. a. For the Management IP Address option:
- DHCP Keep the default, DHCP, to use DHCP reservation on your router to assign a unique IP Address.
- Static Change the IP Address, Netmask, and other settings to make them compatible with your network. b. Click Change and then click Apply. Repeat the instructions in the airFiber Configuration section on your other airFiber radio. After you have configured the airFiber radios, disconnect them and move them to your installation site. 12 Hardware Installation Hardware Installation The mounting hardware of the airFiber radio can be pre-assembled before pole-mounting. Mounting Hardware Pre-Assembly 1. Insert two M10x150 Carriage Bolts into the Lower Mount Bracket. 2. Insert two M10x150 Carriage Bolts into the Upper Mount Bracket with Elevation Rod. 13 airFiber AF5/AF5U Quick Start Guide 3. Attach the Lower Mount Bracket to the I-Bracket using two M8x14 Serrated Flange Bolts. Ensure that the slots face up and securely tighten the bolts. Proper slot orientation 14 Hardware Installation 4. Attach the Upper Mount Bracket with Elevation Rod to the I-Bracket using two M8x14 Serrated Flange Bolts. Note: Ensure that the orientation of the Upper Mount Bracket matches the illustration below, with the Elevation Rod on the correct side. 15 airFiber AF5/AF5U Quick Start Guide 5. Attach the Pole Clamps to the Mount Brackets. a. Slide the slotted hole of each Pole Clamp over one upper and one lower M10x150 CarriageBolt. b. Place one M10 Flat Washer, M10 Lock Washer, and M10 Hex Nut on each M10x150 Carriage Bolt. 16 Hardware Installation 6. Attach the Azimuth Support Brackets together. a. Insert the two M10x100 Bolts into the Azimuth Support Bracket that has two slotted holes. b. Slide the slotted hole of the other Azimuth Support Bracket over one M10x100Bolt. c. Place one M10 Flat Washer, M10 Lock Washer, and M10 Hex Nut on each M10x100 Bolt. 7. Ensure that there is a 10 mm (0.39 in) gap between the head of each Pre-Installed M10x25 Flanged Bolt and the corresponding trunnion on the airFiber radio. 10 mm 17 airFiber AF5/AF5U Quick Start Guide Pole-Mounting 1. Attach the Azimuth Support Brackets to the pole just beneath the area where the airFiber radio will be attached. Note: The mounting assembly can accommodate a 38.1 - 101.6 mm (1.5" - 4.0") pole. a. Orient the Azimuth Support Brackets around the pole so it is aimed in the direction of the other airFiber radio. b. Slide the open slot of the Azimuth Support Bracket over the corresponding M10x100Bolt. c. Tighten the nuts to approximately 50N-m(37lb-ft). 18 Hardware Installation 2. Attach the mounting assembly to a pole. a. Orient the mounting assembly around the pole so it is aimed in the direction of the other airFiber radio. b. Slide the open slot of each Pole Clamp over the corresponding M10x150 CarriageBolt. c. Tighten the M10 Hex Nuts of the M10x150 CarriageBolts to secure the mounting assembly to the pole. 19 airFiber AF5/AF5U Quick Start Guide 3. Lift the airFiber radio and align the two lower Pre-Installed M10x25 Flanged Bolts with the slots on the Lower Mount Bracket. Seat the bolts in the slots. 20 Hardware Installation 4. Align the two upper Pre-Installed M10x25 Flanged Bolts of the airFiber radio next to the slots on the Upper Mount Bracket. Lift the airFiber radio and seat the bolts in theslots. 21 airFiber AF5/AF5U Quick Start Guide 5. Attach a ground wire:
a. Remove the nut from the Grounding Point. b. Attach a ground wire (min. 8 AWG or 10 mm2) to the lug and replace the nut to secure the wire. c. Secure the other end of the ground wire to a grounded mast, pole, tower, or grounding bar. WARNING: Failure to properly ground your airFiber units will void your warranty. Note: The ground wire should be as short as possible and no longer than one meter in length. 22 Connecting Ethernet Connecting Ethernet 1. Push the button and slide the port cover down to access cableports. (The port cover cannot be completely removed.) 2. Connect the Data/PoE Ethernet cable:
a. Feed an outdoor, shielded CAT6 cable up through the rightmost cable feed slot on the bottom of the port cover. b. Connect the cable to the Data port. c. Create a strain relief for the Ethernet cable by feeding a Cable Tie through the tie slot to the side of the cable. d. Wrap the Cable Tie around the cable and tighten. 23 airFiber AF5/AF5U Quick Start Guide 3. Connect the other end of the Ethernet cable from the Data port to the Ethernet port labeled POE on the GigE PoE Adapter. 4. Connect an Ethernet cable from your network to the Ethernet port labeled LAN on the GigE PoE Adapter. 5. Connect the Power Cord to the power port on the GigE PoE Adapter. Connect the other end of the Power Cord to a power source. Note: For added protection, we recommend installing two GigE PoE surge protectors. Install the first surge protector within 1 m (3.28 ft) of the airFiber Data port, and install the second surge protector at the ingress point of the location housing the wired network equipment. 24 Below is a diagram of a finished installation with recommended surge protectors installed. Connecting Ethernet
) t f 8 2 3
(
. m 1
. x a M Outdoor GigE PoE Surge Protector Outdoor GigE PoE Surge Protector Ground to Pole, Tower, or Grounding Block:
Max. 1 m (3.28 ft) from Ground Bonding Point eth0 eth1 eth2 GigE Router or Switch GigE PoE Adapter Power Source 25 airFiber AF5/AF5U Quick Start Guide Alignment Tips To accurately align the airFiber radios for best performance, you MUST align only one end of the link at a time. For more convenient alignment, you may consider using long-range scopes (not included) temporarily attached to your airFiber radios. You may need to use additional hardware to compensate for issues such as the improper orientation of a mounting pole or significant elevation differences between airFiber radios. Before a link is established, the Master's LED Display looks likethis:
GPS and Master LEDs are solidly lit Note: The GPS LED may not be lit if there is a weak GPS signal. A GPS signal is not required for alignment. Link Status LED flashes (Normal Flash 1:1) Remote and Local LED Displays show a double dash Note: The Local LED Display may briefly flash a large number
(such as 95) when there is no link. 26 Alignment Establishing a Link Adjust the positions of the Master and the Slave to establish a link. Note: The Master must be aimed first at the Slave because the Slave does not transmit any RF signal until it detects transmissions from the Master. 1. Ensure that the following bolts and nuts are loose:
Four Pre-Installed M10x25 Flanged Bolts on the airFiber radio
(two on each side) Four M10 Hex Nuts used to lock the elevation alignment on the Upper Mount Bracket (two on each side) 2. Ensure that the pole mount is snug yet the four M10 Hex Nuts attaching the Pole Clamps are loose enough to allow rotation around the pole for azimuth alignment. 27 airFiber AF5/AF5U Quick Start Guide 3. Master Visually aim the Master at the Slave. To adjust the Master's position:
a. Rotate the airFiber radio on the pole to align the azimuth. b. Use the hex nut on the Elevation Rod to adjust the elevation. Note: Do NOT make simultaneous adjustments on the Master and Slave. 4. Slave Visually aim the Slave at the Master. To adjust the Slave's position:
a. Rotate the airFiber radio on the pole to align the azimuth. b. Use the hex nut on the Elevation Rod to adjust the elevation. 5. Check to see if a link is established. Ensure that the Link Status LED is solidly lit green and the Remote and Local LED Displays of the Slave are displaying signal levels. 28 Alignment 6. Slave Aim the Slave at the Master to achieve the strongest signal level on the Remote LED Display of the Slave. Note: Values on the LED Displays are displayed in negative (-) dBm. For example, 67 represents a received signal level of -67 dBm. Smaller numerical values indicate stronger received signallevels. For example, a reading of 49 is stronger than a reading of 55. Note: Maximum signal strength can best be achieved by iteratively sweeping through both azimuth and elevation. 7. Master Aim the Master at the Slave to achieve the strongest signal level on the Remote LED Display of the Master. Note: If the Overload LED lights up, refer to the airFiberAF5/AF5U User Guide at:
documentation.ubnt.com/airfiber 8. Repeat steps 6 and 7 until you achieve a symmetric link, with the signal levels within 1 dB of each other. This ensures the best possible data rate between the airFiber radios. 9. Lock the alignment on both airFiber radios by tightening the nuts and bolts. 10. Observe the Local and Remote LED Displays of each airFiber radio to ensure that the values remains constant while tightening the nuts and bolts. If any LED value changes during the locking process, loosen the nuts and bolts, finalize the alignment of each airFiber radio again, and retighten the nuts and bolts. 11. For each airFiber radio, close the port cover and ensure that the Ethernet cable stays in the cable feed slot. 29 airFiber AF5/AF5U Quick Start Guide There are three methods for determining the received signal level:
LED Displays (described above) airFiber Configuration Interface (webpage) Audio tone (optional equipment required) Refer to the airFiber AF5/AF5U User Guide for instructions on the airFiber Configuration Interface and audio tone methods. Installer Compliance Responsibility Devices must be professionally installed and it is the professional installers responsibility to make sure the device is operated within local country regulatory requirements. The Frequency and Output Power fields are provided to the professional installer to assist in meeting regulatory requirements. 30 Specifications airFiber AF5/AF5U Specifications Dimensions Weight Mount Not Included Mount Included Operating Frequency AF5 FCC 15.247, 15.407, IC RSS 210 ETSI EN 301 893, EN 302 502 Other Regions AF5U FCC 15.247, IC RSS 21 ETSI EN 302 502 Other Regions Max Power Consumption Power Supply Power Method Certifications Mounting Wind Loading Wind Survivability 938.4 x 468.4 x 281.4 mm
(36.94 x 18.44 x 11.08 in) 11.5 kg (25.35 lb) 16 kg (35.27 lb) 5470 - 5600 MHz, 5650 - 5850 MHz 5470 - 5875 MHz 5470 - 5950 MHz 5725 - 5850 MHz 5725 - 5875 MHz 5725 - 6200 MHz 40 W 50V, 1.2A PoE GigE Adapter
(Included) Passive Power over Ethernet
(42-58VDC) CE, FCC, IC Pole Mount Kit (Included) 863 N @ 200 km/hr
(194 lbf @ 125 mph) 200 km/hr (125 mph) Operating Temperature
-40 to 55 C (-40 to 131F) Networking Interface Data Port Management Port
(1) 10/100/1000 Ethernet Port
(1) 10/100 Ethernet Port 31 airFiber AF5/AF5U Quick Start Guide Receive Sensitivity Spatial Streams Modulation Sensitivity FDD TDD Capacity*
Capacity*
8x 6x 4x 2x 1x x 256QAM MIMO 64QAM MIMO 16QAM MIMO
-65 dBm 1024 Mbps 512 Mbps
-72 dBm 768 Mbps 384 Mbps
-77 dBm 512 Mbps 256 Mbps QPSK MIMO
-83 dBm 256 Mbps 128 Mbps Rate QPSK xRT**
Rate QPSK xRT**
-87 dBm 128 Mbps 64 Mbps
-90 dBm 32 Mbps 16 Mbps
* FDD = (2) 50 MHz channels and TDD = (1) 50 MHz channel
** xtreme Range Technology 32 Safety Notices Safety Notices 1. Read, follow, and keep these instructions. 2. Heed all warnings. 3. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Electrical Safety Information 1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturers label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed. 2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician. 3. This equipment is provided with a detachable power cord which has an integral safety ground wire intended for connection to a grounded safety outlet. a. Do not substitute the power cord with one that is not the provided approved type. Never use an adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding wire. b. The equipment requires the use of the ground wire as a part of the safety certification, modification or misuse can provide a shock hazard that can result in serious injury or death. c. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment. d. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short-circuit backup protection. e. Protective bonding must be installed in accordance with local national wiring rules and regulations. 33 airFiber AF5/AF5U Quick Start Guide Limited Warranty UBIQUITI NETWORKS, Inc (UBIQUITI NETWORKS) warrants that the product(s) furnished hereunder (the Product(s)) shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS under normal use and operation. UBIQUITI NETWORKS sole and exclusive obligation and liability under the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion, to repair or replace any Product that fails to conform to the above warranty during the above warranty period. The expense of removal and reinstallation of any Product is not included in this warranty. The warranty period of any repaired or replaced Product shall not extend beyond its original term. Warranty Conditions The above warranty does not apply if the Product:
(I) has been modified and/or altered, or an addition made thereto, except by Ubiquiti Networks, or Ubiquiti Networks authorized representatives, or as approved by Ubiquiti Networks in writing;
(II) has been painted, rebranded or physically modified in any way;
(III) has been damaged due to errors or defects in cabling;
(IV) has been subjected to misuse, abuse, negligence, abnormal physical, electromagnetic or electrical stress, including lightning strikes, or accident;
(V) has been damaged or impaired as a result of using third party firmware;
(VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or
(VII) has not been received by Ubiquiti within 30 days of issuance of the RMA. In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation; all Ethernet cabling runs use CAT5 (or above), and for outdoor installations, shielded Ethernet cabling is used, and for indoor installations, indoor cabling requirements are followed. WARNING: Failure to properly ground your airFiber units will void your warranty. (Please follow the instructions on page 22 for installation of the ground wires.) Returns No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned freight collect or subject to disposal. Information on the RMA process and obtaining an RMA number can be found at: www.ubnt.com/support/warranty. 34 Limited Warranty Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY Data, SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY, ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY, SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES. BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR ITS THIRD PARTY PROVIDERS CONTROL BUYERS EQUIPMENT OR THE TRANSFER OF Data OVER COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, Data LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant that the operation of the Products will be error-free or that operation will be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any nature or description relating to system performance, including coverage, buyers selection of products (including the Products) for buyers application and/or failure of products (including the Products) to meet government or regulatory requirements. Limitation of Liability EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES
(INCLUDING LOST PROFIT, LOST Data, OR DOWNTIME COSTS), ARISING OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you. EXCEPT TO THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to any transactions regarding the sale of the Products. 35 airFiber AF5/AF5U Quick Start Guide Compliance FCC Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Industry Canada This Class A digital apparatus complies with Canadian ICES-003. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that permitted for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numrique de la classe A est conforme la norme NMB-003 Canada. Pour rduire le risque dinterfrence aux autres utilisateurs, le type dantenne et son gain doivent tre choisies de faon que la puissance isotrope rayonne quivalente (PIRE) ne dpasse pas ce qui est ncessaire pour une communication russie. Cet appareil est conforme la norme RSS Industrie Canada exempts de licence norme(s). Son fonctionnement est soumis aux deux conditions suivantes:
1. Cet appareil ne peut pas provoquer dinterfrences et 2. Cet appareil doit accepter toute interfrence, y compris les interfrences qui peuvent causer un mauvais fonctionnement du dispositif. 36 Compliance RF Exposure Warning The antennas used for this transmitter must be installed to provide a separation distance of at least 126 cm (AF5) or 123 cm (AF5U) from all persons and must not be located or operating in conjunction with any other antenna or transmitter. Les antennes utilises pour ce transmetteur doivent tre install en considrant une distance de sparation de toute personnes dau moins 126cm (AF5) ou 123 cm (AF5U) et ne doivent pas tre localis ou utilis en conflit avec tout autre antenne ou transmetteur. CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it. Alert Sign (!) Follows CE Marking Alert sign must be indicated if a restriction on use applied to the product and it must follow the CE marking. RoHS/WEEE Compliance Statement English European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product. 37 airFiber AF5/AF5U Quick Start Guide Deutsch Die Europische Richtlinie 2002/96/EC verlangt, dass technische Ausrstung, die direkt am Gert und/oder an der Verpackung mit diesem Symbol versehen ist, nicht zusammen mit unsortiertem Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulrem Haushaltmll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gert und andere elektrische und elektronische Gerte ber die dafr zustndigen und von der Regierung oder rtlichen Behrden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemes Entsorgen und Recyceln trgt dazu bei, potentielle negative Folgen fr Umwelt und die menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer Altgerte bentigen, wenden Sie sich bitte an die rtlichen Behrden oder stdtischen Entsorgungsdienste oder an den Hndler, bei dem Sie das Produkt erworben haben. Espaol La Directiva 2002/96/CE de la UE exige que los equipos que lleven este smbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El smbolo indica que el producto en cuestin debe separarse de los residuos domsticos convencionales con vistas a su eliminacin. Es responsabilidad suya desechar este y cualesquiera otros aparatos elctricos y electrnicos a travs de los puntos de recogida que ponen a su disposicin el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estar contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener informacin ms detallada sobre la eliminacin segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminacin de residuos de su zona o pregunte en la tienda donde adquiri el producto. Franais La directive europenne 2002/96/CE exige que lquipement sur lequel est appos ce symbole sur le produit et/ou son emballage ne soit pas jet avec les autres ordures mnagres. Ce symbole indique que le produit doit tre limin dans un circuit distinct de celui pour les dchets des mnages. Il est de votre responsabilit de jeter ce matriel ainsi que tout autre matriel lectrique ou lectronique par les moyens de collecte indiqus par le gouvernement et les pouvoirs publics des collectivits territoriales. Llimination et le recyclage en bonne et due forme ont pour but de lutter contre limpact nfaste potentiel de ce type de produits sur lenvironnement et la sant publique. Pour plus dinformations sur le mode dlimination de votre ancien quipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des dchets, ou lendroit o vous avez achet le produit. 38 Declaration of Conformity Italiano La direttiva europea 2002/96/EC richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sullimballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. responsabilit del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per lambiente e per la salute dellessere umano. Per ricevere informazioni pi dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto. Declaration of Conformity esky
[Czech]
Dansk
[Danish]
Nederlands
[Dutch]
English Eesti
[Estonian]
Suomi
[Finnish]
Franais
[French]
Deutsch
[German]
UBIQUITI NETWORKS tmto prohla uje, e tento UBIQUITI NETWORKS device, je ve shod se zkladnmi po adavky a dal mi p slu n mi ustanovenmi sm rnice 1999/5/ES. Undertegnede UBIQUITI NETWORKS erklrer herved, at flgende udstyr UBIQUITI NETWORKS device, overholder de vsentlige krav og vrige relevante krav i direktiv 1999/5/EF. Hierbij verklaart UBIQUITI NETWORKS dat het toestel UBIQUITI NETWORKS device, in overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Bij deze verklaart UBIQUITI NETWORKS dat deze UBIQUITI NETWORKS device, voldoet aan de essentile eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC. Hereby, UBIQUITI NETWORKS, declares that this UBIQUITI NETWORKS device, is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Kesolevaga kinnitab UBIQUITI NETWORKS seadme UBIQUITI NETWORKS device, vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. UBIQUITI NETWORKS vakuuttaa tten ett UBIQUITI NETWORKS device, tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. Par la prsente UBIQUITI NETWORKS dclare que lappareil UBIQUITI NETWORKS, device est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Hiermit erklrt UBIQUITI NETWORKS, dass sich diese UBIQUITI NETWORKS device, in bereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet. (BMWi) 39 airFiber AF5/AF5U Quick Start Guide
[Greek]
Magyar
[Hungarian]
slenska
[Icelandic]
Italiano
[Italian]
Latviski
[Latvian]
Lietuvikai
[Lithuanian]
Malti
[Maltese]
Norsk
[Norwegian]
Slovensky
[Slovak]
Svenska
[Swedish]
Espaol
[Spanish]
Polski
[Polish]
Portugus
[Portuguese]
Romn
[Romanian]
40 UBIQUITI NETWORKS UBIQUITI NETWORKS device, 1995/5/. Alulrott, UBIQUITI NETWORKS nyilatkozom, hogy a UBIQUITI NETWORKS device, megfelel a vonatkoz alapvet kvetelmnyeknek s az 1999/5/EC irnyelv egyb elrsainak. Hr me l sir UBIQUITI NETWORKS yfir v a UBIQUITI NETWORKS device, er samrmi vi grunnkrfur og a rar krfur, sem ger ar eru tilskipun 1999/5/EC. Con la presente UBIQUITI NETWORKS dichiara che questo UBIQUITI NETWORKS device, conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Ar o UBIQUITI NETWORKS deklar , ka UBIQUITI NETWORKS device, atbilst Direkt vas 1999/5/EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem. UBIQUITI NETWORKS deklaruoja, kad is UBIQUITI NETWORKS renginys atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Hawnhekk, UBIQUITI NETWORKS, jiddikjara li dan UBIQUITI NETWORKS device, jikkonforma mal- ti ijiet essenzjali u ma provvedimenti o rajn relevanti li hemm fid-Dirrettiva 1999/5/EC. UBIQUITI NETWORKS erklrer herved at utstyret UBIQUITI NETWORKS device, er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 1999/5/EF. UBIQUITI NETWORKS t mto vyhlasuje, e UBIQUITI NETWORKS device, sp a zkladn po iadavky a v etky prslu n ustanovenia Smernice 1999/5/ES. Hrmed intygar UBIQUITI NETWORKS att denna UBIQUITI NETWORKS device, str I verensstmmelse med de vsentliga egenskapskrav och vriga relevanta bestmmelser som framgr av direktiv 1999/5/EG. Por medio de la presente UBIQUITI NETWORKS declara que el UBIQUITI NETWORKS device, cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Niniejszym, firma UBIQUITI NETWORKS o wiadcza, e produkt serii UBIQUITI NETWORKS device, spenia zasadnicze wymagania i inne istotne postanowienia Dyrektywy 1999/5/EC. UBIQUITI NETWORKS declara que este UBIQUITI NETWORKS device, est conforme com os requisitos essenciais e outras disposies da Directiva 1999/5/CE. Prin prezenta, UBIQUITI NETWORKS declar c acest dispozitiv UBIQUITI NETWORKS este n conformitate cu cerinele eseniale i alte prevederi relevante ale Directivei 1999/5/CE. JL120913 Support support.ubnt.com Community community.ubnt.com Downloads downloads.ubnt.com w w w . u b n t . c o m 2013 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, UbiquitiNetworks, the Ubiquiti U logo, the Ubiquiti beam logo, airFiber, and TOUGHCable are trademarks or registered trademarks of UbiquitiNetworks,Inc. in the United States and in other countries. All other trademarks are the property of their respective owners.
*720-00074-01*
720-00074-01